Clifford Sabre User's Manual
Contents
1. LED Condition Meaning Off System is disarmed On Protected valet mode Flashing System is armed Flashing in cycles TotalR ecall of the last activated trigger or sensor see page 4 Prior Intrusion Attempt Alert When you remotely disarm if you hear 3 chirps instead of the usual one chirp it means that a trigger or sensor was activated in your absence m AutoTesting Each time you remotely arm it tests all triggers and sensors If a trigger malfunction is found you will be visually and audibly alerted immediately with 4 chirps and flashes instead of the usual 2 If a sensor is malfunctioning you will receive the usual 2 chirps and flashes then 5 second later there will be 4 chirps and flashes m Automatic Malfunction Bypass To provide the utmost protection even if a system component malfunctions the system will automatically bypass the faulty point and arm all other triggers and sensors until you can have the system serviced by your local Authorized Dealer 3 m TotalRecall The system s non volatile memory records the identity of the last activated or malfunctioning trigger or sensor which allows your installer to instantly track down a malfunction and save you servicing costs To identify the trigger or sensor held in the system s non volatile memory simply perform the following procedure 1 With the ignition OFF flick the valet switch to one side 2 Press button I to arm the system the2. Turn the ignition off 6 Repeat steps 1 5 for any other features you wish to program Programming Table for User Selectable Features of Program Feature seal iese er i completion Result g chirps confirmation 1 chirp 3 Change state from AutoArming ON 4 seconds after ast step ON to OFF or vice versa 1 chirp 3 AutoArm c Change state from OFF 5 seconds after amp Lock ast step ON to OFF or vice versa Arm Disarm 1 chirp 3 i Change state from Chirp Confir ON 6 seconds after mation ast step ON to OFF or vice versa FACT False Alarm 1 chirp 3 a 4 scan ater ranae are ia Test Tamper last step pening 9 ing Warning Add a New Button I channel 1 code of delice _ 8 Press remote control button 1 chirp fea Fee control has arm disarm been memorized of Program Feature Sie nes an 7 completion Result chirps confirmation Add a New Remote to Button Il channel 2 code of ease E 10 Press remote control button Il 3 chips new remote control mote has been memorized accessory Add a New Remote to Press remote control buttons I ll Button Hl channel 3 code Channel 3 si 9 or button III of the optional 2 chirps of new remote control lent arm dis 4 channel remote control has been memorized arm m User Programmable Remote Controls Your system will respond to as many as four remote controls regardless of each
3. remote control s individual digital coding Thus you can buy additional remote controls including the super high security 4 3 billion code Premier remote controls from any Authorized Clifford Dealer To add a new remote control to the system use the procedures noted in the User Selectable Features section on pages 5 6 m To Erase Unwanted Remote Control Codes If your remote control is ever lost or stolen you can erase its digital codes from the system memory to make sure that the missing remote control can never be used to disarm your system Just use the Add a New Remote procedures noted in the User Selectable Features section on pages 5 and 6 for a total of four times e g if you have one remote control remaining program it four times if you have two remote controls program each twice Copyright Clifford Electronics Inc 1992 31 046A 892 SABOM
4. E AntiScan Press button II to activate another remote controlled option such as a remote trunk release be sure to disarm the Sabre be fore remotely releasing the trunk latch Simultaneously press buttons I II or button III of the optional 4 channel remote The system will arm or disarm with all the indications noted above except the chirp acknowledgements Press button I for 3 seconds The lights will flash repeatedly and the siren will blare for 30 seconds or until you press but ton I again to turn it off Car thieves use electronic scanners that rapidly transmit one remote control code after another to defeat ordinary alarms AntiScan prevents scanners from disarming your system m AutoArming If you forget to remotely arm the system will arm itself automatically passively 30 seconds after the vehicle doors are closed If you re open any door s within the 30 second countdown AutoArming will restart from the beginning once all doors are closed This ensures you ll never accidentally leave your vehicle unprotected AutoArming Enable Disable If you prefer you may deactivate or reactivate AutoArming To do see User Selectable Features on pages 5 6 m AutoArm amp Lock To ensure you can t accidently lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change this setting see User Selectable Features on pages 5 6 m NOTE To prevent AutoArming of the system when fu
5. World Class Auto Security Sabre Owner s Manual Using Your Sabre Security System E 2 Button 3 Channel Remote Control The 2 button 3 channel remote control is a miniature radio transmitter with a range of up to 100 feet Obstructions interference or a weak battery will reduce the range Your 2 button 3 channel remote control is the key to your security system It is an ingenious user friendly device that transmits three distinct and unique digital codes Use it to arm or disarm the system lock or unlock the doors activate its panic feature or control options such as headlight activation or remote trunk release TO ARM THE SYSTEM TO DISARM THE SYSTEM Press button I once You will hear two chirps and the parking lights will flash twice The dashboard LED will flash repeat edly and the car doors will automatically lock some vehicles require an optional power lock adaptor Any attempt to break into the vehicle will immediately disable the starter sound the siren and flash the parking lights Press button I again One chirp and one flash of the parking lights will confirm disarming In addition the car doors will automatically unlock some vehicles require an optional power lock adapand the interior lights will turn on and stay on for 30 seconds or until you start the engine TO ACTIVATE AN OPTION 255 g TO SILENTLY ARM OR DISARM THE SYSTEM TO ACTIVATE THE PANIC FEATURE
6. car s doors will lock or unlock You can also use button II to activate an option E Optional Automatic Starter Interrupt If equipped with an optional relay the system automatically prevents engine starting while the system is armed Only after disarming will the system allow the engine to be started with the ignition key m Tampering Warning Normally the system immediately sounds its siren at the first inkling of an intru sion attempt However you may set the system to issue a rapid five chirp warning whenever the system detects tampering to the exterior of your vehicle If there is any further tampering within the next 30 seconds or if a door the hood or trunk is opened at any time your system will sound a continuous 125dB siren blast To select the mode of your choice see User Selectable Features on pages 5 6 m NOTE Turning on the Tampering Warning feature overrides the FACT fea ture and vice versa FACT False Alarm Control and Test With FACT you ll never experience repeated false alarms If your siren goes off DO NOT remotely disarm the system allow it to run for the full 30 second siren duration The system automatically checks for another activated trigger before sounding the siren a second time Should the siren sound again you will know for sure that someone is tampering with your vehicle LED Status Indicator The LED on your car s dashboard or console will inform you of the system status
7. eling the vehicle either enable valet mode or leave one of the doors open the system AutoArms 30 seconds after all doors are closed m Protected Valet Mode Whenever the alarm is put in protected valet mode all of the alarm functions are bypassed preventing AutoArming and accidental activation of the alarm Use the valet mode whenever your car is either to be serviced by mechanics handed over to car wash personnel or driven by valet attendants It also comes in handy if you ever lose your remote control or its battery dies If you have the AutoArming feature set on when fueling your car either put the alarm in valet mode or leave the driver s door open the system will not AutoArm if a door is open Be sure to ask your installer to show you where the valet switch is located m To turn ON the protected valet mode 1 Insert your ignition key and turn it to the ON position or start the engine 2 Flip the valet switch 3 The LED will glow continuously to indicate that the alarm is in valet mode m To turn OFF the protected valet mode 1 Insert your ignition key and turn it to the ON position or start the engine 2 Flip the valet switch 3 The LED will turn off to indicate that the alarm is in normal operating mode m Keyless Entry in Valet Mode Even if valet mode on you will still be able to remotely control the convenience features For instance simply press button I as if you were arming or disarming and your
8. n again to disarm 3 The LED will blink several times pause then repeat the blink cycle 4 times 4 Count the number of blinks in one cycle and refer to the chart that follows Number of LED blinks per cycle Trigger Sensor that Last Activated or Malfunctioned 1 blink Magnetic Resonance Sensor 2 blinks Door trigger 3 blinks Trunk or hood trigger E How to Interpret the Chirps and Parking Light Flashes When you press the remote control buttons the system will respond with chirps unless you have the chirp muting feature turned on and flashes the parking lights to indicate the system status The meaning of these chirp flash acknowledgements is as follows Number of chirps and flashes Meaning 1 Disarming of the alarm 2 Arming of the alarm 2 and then 4 Armed and there is a sensor malfunction automatically bypassed 3 Disarmed and there was an intrusion attempt 4 Armed and there is a trigger malfunction automatically bypassed E Multi Level Chirp Control Whenever you wish you may silence the system s arm disarm chirps The short term and one time chirp muting capabilities are especially valuable when parking late at night in a quiet residential area You have several choices m Extended Chirp Silencing Lets you completely silence the chirps until you wish to restore them See User Selectable Features on pages 5 6 m Short Term Chirp Muting Lets you silence
9. the chirps for a single arm and disarm cycle To enable short term chirp muting simply turn the vehicle s igni tion switch rapidly ON then OFF The next time you arm and later disarm the system there will be no chirps After which the chirps are restored m One Time Remote Chirp Muting The most simple of all To remotely arm or disarm the alarm silently press buttons I II on the remote control 4 User Selectable Features Your Sabre vehicle security system allows you to set many of its features to your own personal preferences We have made the programming procedures very simple to make a change you just flick the valet switch a few times The system comes from the factory with all of its features pre programmed as noted in the table below and on page 6 To change any of the settings use the procedure noted To restore the feature to its factory setting just repeat the procedure 1 Select the feature you wish to program from the table on the following pages Note the number of flicks and chirps associated with that feature 2 Insert your ignition key and turn it to the ON position 3 Immediately flick the valet switch back and forth counting the number of chirps you hear Stop when you reach the appropriate number of chirps 4 If noted do the secondary action 5 You will hear one or more chirps as noted in the program completion con firmation section to confirm that you have changed the feature setting
Download Pdf Manuals
Related Search