Home
Clifford ACE 2000 User's Manual
Contents
1. CLIFFORD The Science of Security ACE 2000 Complete Owner s Manual USA Headquarters 20750 Lassen Street Chatsworth California 91311 1 800 CLIFFORD or 1 800 824 3208 or 1 818 709 7551 Canada Headquarters 4513 Dobrin Street Montreal Quebec H4R 2L8 1 800 361 3444 or 1 514 332 4444 UK Headquarters Boundary Business Court 92 94 Church Road Mitcham Surrey CR4 3TD 0800 929949 or 0181 646 8440 Germany Headquarters Schlesische StraRe 27 10997 Berlin 0130 115 681 oder 030 611 2602 Mexico Headquarters Saratoga 804 B Col Portales Deleg Benito Juarez 03300 M xico D F 01 800 021 2543 0 5 605 0382 Clifford systems are covered by one or more of these Clifford Electronics USA patents 4 158 874 4 233 642 4 327 444 4 383 242 4 430 685 4 845 464 4 887 064 4 890 108 4 922 224 4 997 053 5 081 667 5 146 215 5 157 375 5 467 070 5 650 744 and other patents pending Standard Features The following are standard features of this system Some vehicles may require optional parts wiring and a few are incompatible with some features m Lifetime warranty see terms amp conditions m Two remote controls m 100 range 300 with optional ElectroLoop Antenna m ACG 2 Anti CodeGrabbing protection m Low remote control battery warning m PlainView 2 coded valet mode m Select your own secret code Remote controlled valet mode M Starter interrupt Dual Zone Piezo Sensor detects
2. set off or you may set the system to sound them only upon trigger activation When set to trigger only the basic siren wail will sound if a sensor is activated but the Personalized Siren Sounds will play if the hood trunk or a door is opened See User selectable features column 1 row 3 Smart AutoTesting Each time you remotely arm the system it tests all triggers and sensors If the hood or trunk is open the system will immediately sound 4 chirps and 4 indicator light flashes instead of the usual 2 and 2 If a door is ajar you ll receive 2 chirps and 2 flashes then 5 seconds later there will be 4 chirps and 4 flashes If a sensor is malfunctioning you will receive the usual 2 chirps and 2 flashes then 10 seconds later there will be 4 chirps and 4 flashes NOTE Since this is a warning indication you will hear the 4 chirps even if you use the chirp muting feature Specific malfunction identification The system can also indicate the specific trigger or sensor that is malfunctioning If you get the 4 chirp 4 flash signal upon arming perform the following to identify the malfunctioning trigger or sensor 1 Remotely disarm then turn on the ignition The LED status indicator inside your vehicle will be flashing pause then repeat 2 Count the number of flashes in one cycle between pauses for your convenience the flash cycle repeats a total of 5 times and refer to the chart below LED flashes
3. cellphone cloning devices The thief then plays back the code when you re gone instantly disarming the alarm and unlocking the doors It s like leaving your keys and remote in the door Many non Clifford alarms can be defeated that easily and some of the latest smart code grabbers can even decipher the code hopping jumping sequence used by other car alarm manufacturers In contrast your ACE 2000 uses complex digital signal processing and unbreachable code encryption to randomly change the digital code every time you use the remote control Your remotes will never transmit the same code twice and the control unit will never accept the same code twice Thus the code played back by the code grabber even the latest generation smart code grabbers will never be accepted by your ACE 2000 system Automatic remote control low battery warning If your remote control battery is low you ll hear a rapid 5 chirp sequence when you disarm instead of the usual one chirp with the Self Powered SmartSiren 4 option you ll hear a low pitched chirp Replacement batteries are available from any Authorized Clifford Dealer Remote control battery replacement Replacement of a remote control battery is simple but any Authorized Clifford Dealer will be happy to do it for you without cost provided that you buy the replacement battery at their shop it s a good idea to keep a spare battery in your glove box just in case 1 Insert a small thin s
4. Meaning 1 flash Activation of optional sensor 2 flashes Activation of Piezo Sensor 4 flashes Door open ajar 5 flashes Trunk hood open ajar trunk only if you have the IntelliStart 4 option 6 flashes Hood open ajar only if you have the IntelliStart 4 option 7 flashes Ignition switch was turned on while the system was armed 8 flashes Three or more incorrect valet codes were entered 10 flashes Power tampering or the vehicle battery is very low Tf your vehicle has a factory installed feature that turns off or dims the interior courtesy lights several seconds after you exit the vehicle the system cannot provide this indication Automatic malfunction bypass with AutoReMonitoring The system automatically bypasses any faulty point and arms all other triggers and sensors for the utmost possible protection If you accidentally arm with the hood trunk or a door open just close it no need to disarm and rearm and the system will again monitor that point Smart prior intrusion attempt alert If you hear three chirps when you disarm it means that a trigger or sensor was activated in your absence When you turn on the ignition the LED will flash 1 8 times pause then repeat the flash cycle 4 more times Count the flashes in one cycle and refer to the chart on the previous page Multiple event TotalRecall The system s memory records the identity of the last eight activated or malfunctioning triggers and sensors which allows your i
5. and then re enter your new code If the LED flashes on your new code has been accepted If the LED does not light the two codes did not match and the system has reverted to your previous code NOTE 5 Lets you arm disarm with the remote control of a G4 system on your other vehicle s For instance to set the button of the other car s remote to arm and disarm this system select column 4 row 1 then press the button of the other car s remote you ll hear one chirp Immediately press the button again you will hear a 2 chirp confirmation The button of the other vehicle s remote will now arm disarm this system NOTE 6 The features in this column allow you to control your system with the remote control of a G4 system on your other vehicle s Just select the function you wish then press the unused button or button combination on the other remote that you want fo use to perform that function on this system you will then hear a the chirps noted NOTE You must first set a button or button combination on the other car s remote that will arm disarm the system column 4 row 1 before these others will be accepted EXAMPLE Turn on Lock upon AutoArming and turn off Remote Valet Mode and FACT In this example we ll change three different features in just one programming session We ll turn on the Lock upon AutoArming feature turn off remote controlled valet mode and turn off the FACT anti falsing feature 1 Enter program mode
6. open and that this may indeed be a genuine theft attempt E Automatic noise abatement Alarm sounding is limited to five siren duration cycles even if a door is left open in the wake of an intrusion E Long term chirp silencing You may silence the arm and disarm chirps on a long term basis until you decide to restore them Your vehicle s parking light flashes will continue to provide visual confirmation of remote controlled system arming and disarming See User selectable features Selectable siren duration You may change the factory set 30 second siren duration to 60 or 90 seconds via the programming procedure or via the CliffNet Wizard software See User selectable features E Personalized Siren Sounds requires the Self Powered SmartSiren 4 option The optional Self Powered SmartSiren 4 sounds six different alarm sounds You may turn any of the six sounds on or off via User selectable features programming to create a different combination of sound patterns So if you hear a siren at a distance you will know for sure whether it is your car or someone else s See User selectable features column 1 row 2 What s more with the optional CliffNet Wizard software and DataPort Replicator Cable you may select up to six sounds from more than a dozen different siren sound choices for truly unique customization E Choose when your Personalized Siren Sounds play You may choose to have your Personalized Siren Sounds play every time the alarm is
7. as previously noted ignition on enter your valet code press and hold the button on the PlainView 2 switch until you hear a chirp 2 Since the Lock upon AutoArming feature is in column 3 row 2 of the Table go to column 3 by pressing the blank button on the PlainView 2 switch three times Wait for the 3 chirp column 3 confirmation Then press the button twice you ll hear a chirp each time you press the button After a brief pause you ll hear 2 chirps to confirm that Lock upon AutoArming is now on 3 Since FACT is also in column 3 there is no need to reselect column 3 Therefore you can go straight to the row selection Select row 4 by pressing the button four times After a brief pause you ll hear one chirp to confirm that FACT is now off 4 You ll note that the Remote valet mode feature is at column 2 row 3 To change to column 2 press the blank button twice then wait for the 2 chirp column 2 confirmation Press the button three times to select row 3 After a brief pause you ll hear one chirp to confirm that the Remote valet mode feature is now turned off 5 To exit the program mode turn the ignition off You ll hear 3 chirps to confirm program mode exit 8 Reset All Features If you wish to reset all the user selectable features to their normal factory presets you can do so simply by choosing the Reset all features selection column 1 row 7 on the Table of User Selectable Features If you do so all features except
8. both minor impacts and theff related tampering m Smart DataPort input m For complete optional control of your system via your Windows PC m For smart accessory interfacing m FACT anti false alarm circuitry m Passive AutoArming if you forget to arm with the remote control m Lock upon AutoArming self locking m Visual AutoArming countdown confirmation Instant AutoArm bypass m High Output Siren m Remote controlled chirp muting m Long term selectable chirp muting m Remote siren silencing without disarming if falsely triggered m Power door lock control some vehicles may require optional relays m Ignition switch controlled AutoLocking AutoUnlocking m Built in parking light flasher m Courtesy light s turn on when you disarm with the remote requires optional relay m Remote panic feature m Smart panic locking unlocking based on whether the engine is on off m Smart optional remote trunk release prevents falsing m Smart AutoTesting self diagnostics m With specific trigger amp sensor identification m Malfunction AutoBypass m Automatic trigger remoniforing if trunk hood was open when arming m Smart Prior Intrusion Attempt Alert m With specific trigger amp sensor identification M TotalRecall 8 event trigger sensor memory report m With specific trigger amp sensor identification Remote control code learning m Clear all remotes if ever lost or stolen m LED status indicator m Flash indications reveal s
9. chase receipt In the absence of such purchase receipt the warranty period shall be one 1 year from the date of manufacture Any damage to the product s as a result of misuse abuse neglect accident incorrect wiring improper installation destruction or alteration of the serial number repair or alteration outside our factory or any use violative of instructions furnished by us will void the warranty This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith This warranty is not transferable Clifford Electronics makes no warranty against theft This warranty is not to be alee as an insurance policy against loss Warranty on installation labor removal and reinstallation charges are not the responsibility of Clifford Electronics Inc
10. crewdriver blade in the slot near the keyring opening you may leave the keyring in place and turn it to separate the two halves 2 Remove the old battery noting the and indications and replace it with the new one 3 Put the enclosure back together by first aligning the top of the remote then snapping the case back together at the bottom 3 Adding new remote controls For other drivers or to control Clifford G4 systems on your other cars with the same remote you can buy additional remote controls from any Clifford Dealer or direct from the Customer Service Department of your nearest Clifford Headquarters listed on the front cover and program them into the system yourself ACE 2000 will respond to as many as four remote controls NOTE Clifford G4 systems will respond only to G4 type ACG 2 remote controls Older Clifford ACG and non ACG remote controls are not compatible with G4 systems To add a new remote control to the system use the Add new remote feature column 1 row 1 of the User selectable features section User Selectable AutoArming If this feature is enabled and you forget to remotely arm the system automatically arms itself 30 seconds after the vehicle doors are closed For your convenience if you re open any door s within the 30 second countdown AutoArming restarts the 30 second delay from the beginning after all doors are closed ACE 2000 has these additional features E AutoArming entry delay If you tempo
11. eone bumping your car door with their s and sounds a brief warning tone If needed sensitivity of this sensor can be readjusted by any Authorized Clifford Dealer preferably your installing dealer To prevent falsing system sensors are bypassed when the engine is remotely started if you have the IntelliStart 4 option Ask your Authorized Clifford Dealer about these optional sensors that will further enhance the security of your vehicle Glass Tampering Sensor Today s thieves shatter vehicle windows with a small metal punch device that does not create any vibrations for an impact sensor to detect The Glass Tampering Sensor detects the sound of glass breaking and glass tampering attempts and will trigger the alarm E Digital Tilt Motion Sensor Detects less than one degree of lifting or any minute motion of the vehicle while completely ignoring all other conditions that falsely set off all other sensors Even if you park on a hill the Digital Tilt Motion Sensor will accurately respond to the first hint of tampering to reliably protect your wheels and entire vehicle High Output Siren E Remote siren silencing If triggered by a non threatening event you can silence the siren without remotely disarming Press button w a while the siren is sounding Two chirps confirm that the sensor activated the alarm and the system is remaining armed Four chirps confirm that the system is still armed but that the ignition is on or the hood trunk or a door is
12. feature settings You can change settings simply by mouse clicking the graphical button for each feature You can customize features add or delete remote controls change remote control button assignments view a chronological history of trigger and sensor activations and much more It s actually fun And secure To learn more and download this free software go to www clifford com wizard User selectable features You may set many of the features to your own preferences Once you ve changed a few settings you ll find that programming the system is so easy that you can even do it while driving The system comes with all of its features preprogrammed as noted by the bold type in the Table of user selectable features To change any of the settings use the steps noted below To restore the feature to its factory setting just repeat the procedure NOTE For greater programming ease and even more system control consider the CliffNet Wizard Windows PC software interface www clifford com wizard How to change a user selectable feature Briefly here s how it will work e You will pick a feature from the following Table of User Selectable Features noting the feature s column and row numbers e You ll enter program mode by entering your valet code and pressing the button of the dash or console mounted PlainView 2 switch until you hear a chirp e Press the blank PlainView 2 switch button the same number of times as the column number
13. g 4 chirps 5 presses AutoLock off on NOT USED NOT USED NOT USED Clear all remotes NOTE 6 Other vehicle s remote 6 presses pulovnkgekeetion NOTE 3 NOT USED window rolldown venting 6 chirps Reset all features except remotes Set a new secret valet code NOTE 6 Other vehicle s remote 7 presses and valet code to factory settings NOTE 4 NOT USED remote valet mode 7 chirps Requires optional wiring or accessory ask your Clifford Dealer for details NOTE 1 Press the button of the new remote You ll hear one chirp Press the button again You ll hear two chirps to confirm that the new remote control has been added NOTE 2 This feature requires the optional Self Powered SmartSiren 4 If so equipped selection of this feature will cause the system to sound a few seconds of siren sound 1 Press the blank button to turn on this sound or the button to turn it off It will then sound a few seconds of sound 2 Repeat blank ON OFF for each of the six sounds NOTE 3 You ll hear two chirps to indicate all remotes have been cleared from memory You must now add new existing remotes with the Add new remote control feature and or the Other vehicle s remote feature NOTE 4 Immediately PRESS THE BLANK BUTTON THEN enter your new code wait for the two chirps then turn off the ignition you ll hear 3 chirps to confirm program mode exit You MUST now turn the ignition back on
14. g the end of its useful life see the Low battery warning section for details Electrical radio frequency interference obstructions weather conditions and even sunspots can interrupt the signal from your remote to the system The remote controls are the keys to your system But these remote controls are much more secure than car keys because each incorporates our ACG 2 Anti CodeGrabbing 2 technology with trillions of digital codes for the ultimate protection against remote control cloning devices You will use your ACE 2000 remote control to arm and disarm the system lock and unlock the doors activate deactivate the panic feature enable exit valet mode and command options such as a remote trunk release power window control electric garage door interface or even remote starting of the engine and heater or air conditioner among other options Remotely controlling your Clifford system TO ARM Press button al Upon arming two siren chirps two parking light flashes dashboard LED flashes repeatedly and doors lock TO DISARM Press button m f Upon disarming one chirp one parking light flash LED turns off doors unlock and the interior lights turn on TO ARM OR Simultaneously press both the mf button and the button to arm or disarm without chirp acknowledgments DISARM SILENTLY TO PANIC For three seconds continually press button d a The parking lights will flash repeatedly and the siren will blare for 30 seconds If the ignition is
15. ically checks for another activated sensor or trigger to verify that an intrusion is in progress This feature is user selectable Starter Autolmmobilization While armed your system immobilizes the starter to prevent a thief from starting the engine The engine will remain immobilized even if a thief were to cut power to the system or find and remove the system control unit Optional Wireless Immobilizer Clifford s optional Wireless Immobilizer interrupts a second point in the vehicle such as the ignition or fuel pump This Clifford innovation provides immobilization without any wires to the control unit so a thief could not find the Wireless Immobilizer even if he tried tracing the system wires Operation of the Wireless Immobilizer is automatic and user transparent BE sure to keep the record your Clifford installer provides as to the location of the Wireless Immobilizer in case your vehicle needs future servicing NOTE If your vehicle s engine ever stalls the Wireless Immobilizer WILL engage You must turn the ignition all the way to OFF in order to restart How to interpret the LED status indicator The LED on your car s dashboard or console will inform you of the system status LED Condition Meaning Off System is disarmed and in normal operating mode i e valet mode is off On Valet mode is on the vehicle may be entered without having to disarm Flashing rapidly ignition off System is armed and pr
16. nstaller to instantly track down malfunctions To identify the triggers and sensors held in the system s memory use the following procedure 1 Remotely arm and disarm while pressing the blank button on the PlainView 2 switch 2 The LED will flash 1 10 times to indicate the most recently activated point pause flash 1 10 times to indicate the second most recently activated point and so on 3 Write down the number of flashes between pauses and refer to the chart above With the optional CliffNet Wizard you Il see this chronological report right on screen SmartPowerUp 2 If power is removed SmartPowerUp 2 ensures the system automatically restores itself to its previous state when power is restored So if a thief disconnects the power and then restores it in an attempt to start the car the system will re arm and instantly sound the siren while continuing to immobilize the starter If your vehicle is to be serviced by a mechanic just put the system in valet mode If the mechanic needs to interrupt power your system will automatically return to its valet mode state when power is restored there will be no alarm activation Optional CliffNet Wizard amp DataPort Interface Connector If you opted to have the Clifford DataPort interface connector installed with your system you can use our CliffNet Wizard software to access your system through your Windows PC CliffNet Wizard will show you on your PC screen all your user programmable
17. on indicating you are in the car the doors will automatically lock to prevent an assailant from entering note some vehicles are unable to lock the doors while the ignition is on If the ignition is off the doors will unlock allowing you to enter immediately without fumbling with your keys TO REMOTELY If you have this option press button while the system is in its disarmed state OPEN THE TRUNK TO REMOTELY If you have this option press button to remotely start the engine or shut it down if idling under the control of IntelliStart 4 START THE ENGINE Before remote starting be sure to see the Remote Engine Starting DOs and DON Ts noted in the IntelliStart 4 user s manual Since remote control range is an issue with remote engine starting you may want to consider the optional ElectroLoop Antenna option TO TURN VALET Simultaneously press buttons and to enable exit valet mode MODE ON OR OFF TO REMOTELY OPEN If you have this option press buttons d a and after disarming to fully open the windows controlled by SmartWindows 4 OR VENT WINDOWS On hot days press this button combination right after arming to vent the windows slightly while the system remains armed ACG 2 Anti CodeGrabbing 2 ACG 2 protects you and your automobile from code grabbing devices Code grabbers literally record from hundreds of feet away the code sent by your car alarm remote control code grabbers are very similar to but simpler than
18. otecting your vehicle Flashes pause flashes Either an error such as arming with the trunk open or indicates the trigger or sensor that was tripped Automatic Battery Saving Mode To conserve vehicle battery power the LED actually draws more current than the entire control unit if the system has remained continuously armed for 48 hours the flash rate will automatically slow to half the normal rate After 96 hours it slows to one quarter User Selectable AutoLock and AutoUnLock Some vehicles are incompatible with the AutoLock and AutoUnLock features For your safety and that of your passengers the doors automatically lock the instant you turn on the ignition When you turn the ignition off AutoUnLock automatically unlocks the doors These are user selectable features PlainView 2 Coded Valet Mode All car alarms have a valet mode that turn off the security features This mode is often used to turn off the alarm if the system is not responding to the remote However thieves can disable other alarm brands by simply hotwiring the ignition and flicking the alarm s easy to find hidden valet switch In contrast your ACE 2000 system has safeguards that ensure a thief cannot enable the valet mode as a way of turning off your system To enable valet mode the driver must first enter the secret valet code on the PlainView 2 switch mounted on your vehicle s dash or console When the system is in valet mode it ove
19. progress through each possible setting 7 You may now select another feature or exit program mode continued a To select another feature in that same column repeat step 5 within the next 5 seconds after 5 seconds 3 chirps mean you are back to the Feature Select position b To select a different feature column go to step 4 c To exit program mode turn the ignition off you ll hear 3 chirps and the LED will turn off If driving just wait 60 seconds and the system will automatically exit program mode If you make an error just turn off the ignition and start again Table of User Selectable Features Feature Select 1 blank press 2 blank presses 3 blank presses 4 blank presses Add a new remote control Chirps off on a NOTE 5 Other vehicle s remote ip press NOTE 1 1 2 chirps AutaAmning oien arm disarm 1 then 2 chirps Personalized Siren Sounds sad NOTE 6 Other vehicle s remote 2 presses NOTE NOT USED Lock upon AutoArming off on irurikrelease 2 chips 3 presses Play Personalized Siren Sounds trigger only always 1 2 chirps Remote valet mode via button combo S 9K off on AutoArming entry delay off on NOTE 6 Other vehicle s remote silent arm and disarm 3 chirps 4 presses Siren duration 30 60 90sec 1 2 3 chirps AutoStart both off both on temp only battery only 1 2 3 4 chirps FACT off on NOTE 6 Other vehicle s remote remote engine startin
20. rarily lose the use of your remote controls you may turn on the AutoArming entry delay feature If this feature and AutoArming are turned on it allows you to enter the car if it previously AutoArmed and silently disarm the system by turning on the ignition within 15 seconds of opening the door See User selectable features column 3 row 3 E Visual acknowledgment Five seconds after you exit close all the doors and the interior light has turned off the indicator lights flash twice to confirm the AutoArming countdown is progressing Then 25 seconds later the system will AutoArm E Lock upon AutoArming To ensure you can t accidentally lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change this setting see User selectable features E Instant AutoArming bypass Prevents AutoArming when fueling the vehicle and at other times when you wish to temporarily bypass AutoArming To activate Instant AutoArming Bypass rapidly turn the ignition switch to ON then OFF You will hear a siren chirp to confirm that the system will not AutoArm The system automatically reverts to its normal operating mode when you next start the engine False Alarm Prevention amp FACT With FACT False Alarm Control and Test you ll never experience repeated false alarms If the siren sounds DO NOT disarm allow it to run for the full siren duration Before sounding the siren a second time the system automat
21. rrides AutoArming and all other security features At various times you will need to switch the system off For instance when refueling or washing your car The system s factory set valet code is 2 blank NOTE If you temporarily lose the use of your remote controls you can disarm the system by enabling valet mode Entering a code To enter your code press the button the appropriate number of times on the PlainView 2 switch followed by the blank button To enter a zero you simply press the blank button EXAMPLE To enter a code of 1203 you would press blank blank blank blank To enable valet mode 1 Turn the ignition switch to its ON position or start the engine if it is not already running 2 Enter your valet code on the PlainView 2 switch 3 Continue pressing the blank button for 4 seconds Release the button The LED will continue to remain on for ongoing visual confirmation of valet mode To exit valet mode and restore normal operation 1 Turn the ignition switch to its ON position or start the engine if it is not already running 2 Enter your valet code on the PlainView 2 switch The LED will turn off How to set your own secret valet code You may choose any 1 4 digit code but the first digit must not be a zero e g 1023 is a valid code 0123 is not See User selectable features Example Let s say you want to set a valet code of 4301 1 From the Table of user selectable features
22. tatus m Automatic battery saving mode Multiple vehicle control from the same remote control m Multiple sensor trigger inputs m User programmable features m SecureAccess coded programming m Programmable even while driving Maintenance Your Clifford system requires no maintenance except for periodic replacement of the remote control batteries This product like any electrical device in your vehicle requires your car battery be in proper working order and fully charged To ensure proper operation periodically have your vehicle battery load checked at any local garage mechanic Also make sure the battery cables and connections are tight and free from corrosion Welcome to the world of high technology vehicle security and convenience ongratulations on the purchase of your Clifford Electronics mobile security convenience system Clifford Electronics has long been recognized as the leading manufacturer of high technology vehicle security systems Our commitment to technological innovation quality and reliability is clearly evident in your Clifford system Yet despite all its sophistication your system is amazingly easy to use never more difficult than a few presses of a button Your remote controls The two 3 button remote controls are sophisticated miniature radio transmitters each powered by a 3 volt lithium battery A weak remote control battery will reduce range the system will warn you if the battery in your remote is nearin
23. the programmed remote controls and your valet code will be reset to the factory settings that are indicated in BOLD type on the Table of User Selectable Features To reset all remote controls use the Clear all remotes feature in column 2 row 6 To reset your valet code use the Set a new secret valet code feature in column 2 row 7 Lifetime limited factory warranty terms amp conditions Clifford vehicle security systems and accessories require professional installation by an Authorized Clifford Dealer Unless the system is sold and installed by an Authorized Clifford Dealer all product warranties and guarantees are void As the manufacturer Clifford Electronics warrants to the original consumer purchaser the system control unit and remote controls to be free from defects in material and workmanship for as long as you own the vehicle in which the system was originally installed All other parts of the system and accessories to the system are warranted to be free from defects in material and workmanship for one 1 year from the date of purchase Clifford Electronics will repair or replace at its option and free of charge during the warranty period any system component that proves defective in material or workmanship under normal installation use and service provided the product is returned to our factory by an Authorized Clifford Dealer transportation charges prepaid Products returned to our factory must be accompanied by a photocopy of the pur
24. then the button a number of times equal to the row number 1 Refer to the Table of user selectable features and make note of the column across number and the row down number of the feature s you wish to program 2 Turn the ignition on or start the engine skip this step if the engine is running 3 Enter your valet code then press and hold the button of the PlainView 2 switch for about 4 seconds until you hear a siren chirp 4 Select the feature column Press and release the blank button of the PlainView 2 switch the same number of times as the column number you wish Pause You will hear the same number of chirps as the column number audibly confirming your selection 5 Select the feature row Press and release the button the same number of times as the row number You ll will hear a chirp each time you press to help you count NOTE You have 5 seconds to enter the row number after selecting the column number If you wait too long the system jumps back to the Feature Select position this is indicated with 3 chirps If you wait another 60 seconds the system will exit program mode 6 Pause You will hear either one or two chirps Two chirps ON one chirp OFF If there is a NOTE for the selected feature perform the actions noted NOTE Some features such as AutoStart column 2 row 4 used with the optional IntelliStart 4 accessory have multiple settings Simply reselect the feature additional times to
25. ur code Remote Controlled Valet Mode Valet mode turns off all security features and prevents AutoArming when for instance having your car washed To turn valet mode on off simultaneously press the and em buttons Two parking light flashes confirm valet mode on one flash confirms valet mode off The dashboard LED will glow continuously when valet mode is on Your system remains in valet mode until you again press the and buttons to turn it off and restore normal operation This is a user selectable feature and may be programmed off if you wish to use this button combination for a different function Smart trunk release option If you have this option you may use the em button to remotely release the trunk latch The system s electronic interlock prevents unintentional activation of the remote trunk release when you drive or when the system is armed The Smart Trunk Release feature requires installer programming so if you have the optional trunk release installed you may want to verify that it will NOT activate when the system is armed If it can be activated while armed causing the alarm to sound please return to your installing Clifford Dealer and have them correct this it only takes a couple minutes and there will be no charge to you Dual Zone Piezo Sensor The Dual Zone Piezo Sensor detects theft related vibrations impacts and triggers the alarm It also has a warning zone that detects less serious occurrences such as som
26. you would note that the Set a new secret valet code feature is in column 2 row 7 2 Enter program mode by turning on the ignition entering your current code then pressing and holding the button of the PlainView 2 switch for 3 seconds until you hear a chirp 3 Select column 2 by pressing the blank button twice After a brief pause you will hear 2 chirps to confirm that you have selected feature column 2 Within 5 seconds select row 7 by pressing and releasing the button 7 times To help you count you will hear a chirp each time you press the button After 7 presses immediately press the blank button then immediately enter your new code D Example To enter 4301 as your new code you would press the switch buttons in this manner blank blank blank blank Wait for the 2 chirp confirmation Turn off the ignition to exit program mode you ll hear a 3 chirp confirmation VERY IMPORTANT You must immediately test your new secret valet code Turn on the ignition enter your new code then press and hold the blank button for 4 seconds The LED will illuminate to indicate that the system is in valet mode Turn the ignition off The system is now in valet mode oS If the LED does not illuminate the new code you programmed and the one you just entered do not match In such a case the system will revert to the previous code 8 To exit valet mode and return to normal operation turn the ignition on and enter yo
Download Pdf Manuals
Related Search
Related Contents
Télécharger la documentation battery - Snorkel Huile-moteur COFFEE MAKER Im 2044 - Personal Home Pages (at UEL) VadaTech VT85x User Manual[1] Copyright © All rights reserved.
Failed to retrieve file