Clarion VRX8271 User's Manual
Contents
1. Press the FUNC button 7 to turn on the power Do not give an excessive force to the opera tion panel Even after the operation panel is installed and locked pulling it forcefully acti vates the sensor of the DCP and turns off the power to the unit or may cause a breakdown Turning on and off the monitor Each time you press the MONI button 7 the monitor is turned on and off When a button other than the volume adjustment button is pressed or during rear vision monitoring the monitor off mode is canceled Mute Each time you press gt I center of the ENT button T mute is turned on and off MUTE is displayed when mute is turned on in radio mode and PAUSE is displayed in CD changer mode Adjusting the tone Notes e When the DSP or equalizer unit DPH9100 DPH7100 or EQH5100 sold separately is connected to the source unit the tone is adjusted by the DSP or equalizer unit and the tone adjustment mode cannot be selected For further information see the section Operating the DSP and Equalizer If no operation is made for about 5 seconds after each operation the unit returns to the previous mode and the settings made are stored 1 Press the AM button 3 to go to the tone adjustment mode BA bass and TR treble are displayed in the information panel 2 13 2 Slide the Up Down button 1 to 4 left gt right A up or Y down to adjust the ton2. 4 Press the ADJ button 15 to return to the pre vious display A WARNING THIS PRODUCT IS NOT INTENDED FOR VIEWING TELEVISION BROADCASTS OR VIDEO TAPES OR FOR PLAYING VIDEO GAMES Such uses of this product may distract the driver or interfere with the dri ver s safe operation of the motor vehicle and may violate state law CLARION DIS CLAIMS ANY LIABILITY FOR ANY BODILY INJURY INCLUDING FATALITIES OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY SUCH UNINTENDED USES OR FROM ANY IMPROPER USE OF THIS PRODUCT 21 Adjusting the brightness and tone of color Notes This function is not available unless you stop the car and apply the parking brake e This function is not available when the display is stored The brightness can be adjusted only when the pic ture of the rear vision camera is displayed 1 Press the ADJ button 5 to select the CON FIGURATION display 2 Slide the Up Down button 4 to Y down or A up to move the cursor to DISPLAY CAMERA MONTOR men Bag Adjusting the brightness 3 Slide the Up Down button 4 to right to select either of BRIGHT COLOR or HUE Each time you slide the Up Down button 1 to P gt right the adjustment mode switch es in the following order C BRIGHT gt COLOR gt HUE BRIGHT Adjusts the brightness of the dis play COLOR Adjusts the color saturation HUE Adjusts the tone of color red is emphas
3. This unit can control a separately sold CD changer to store and play up to 18 CDs Note CD ROM discs cannot be played Listening to a CD 1 Press the FUNC button 7 and select CD changer mode Playback starts automatically 2 Press one of the Disc No buttons 9 No 1 to No 6 corresponding to each CD to select one The selected CD No becomes pink in the dis play Note e f a slot in a magazine is empty that slot No does not appear in the display and cannot be selected 3 Slide the Up Down button 1 to right or left to select a track song gt Selects the next track Example The third track from the current one is select ed by sliding the button 3 times To return to the beginning of the current track slide the Up Down button 1 once to 4 left 4 Selects the previous track Example The third track before the current one is selected by sliding the button 1 3 4 times the first sliding returns you to the beginning of the current track Notes e After CD No 6 is played CD No 1 is played again However when a CD changer capable of storing 12 or 18 CDs is connected to the unit all CDs in all magazines are played sequentially unless the magazine is locked The empty slot No is skipped and the next CD is Played Fast forward and fast backward 1 Slide and hold the Up Down button 1 to gt right and lt q left The CD fast forwards or fast backwards while the
4. to select the CON 3 Press the ADJ button 15 to return to the pre vious mode Switching the background color The background color of the display can be switched between blue and black 1 Press the ADJ button 15 to select the CON FIGURATION display 2 Slide the Up Down button 1 to W down or A up to move the cursor to COLOR 3 Each time you slide the Up Down button fi to P right the background color toggles between blue COLORI and black COLOR2 4 Press the ADJ button 15 to return to the pre vious mode Always turning on the button illumi nation on the operation panel The button illumination on the operation panel when the display is turned upward can be switched between AUTO and OFF AUTO Button illumination on the operation panel turns on for 5 seconds OFF Button illumination is always on when the power is turned on 23 Note e This function is not available when the display is stored 1 Press the ADJ button 15 to go to the CON FIGURATION display 2 Slide the Up Down button T to W down or up to move the cursor to DCP ILL 3 Slide the Up Down button T to right to switch indication AUTO to OFF 4 Press the ADJ button 15 to return to the pre vious mode To set AUTO again switch OFF to AUTO manually Turning on and off the operation sound You can turn o
5. 2 Press the DISP button 0 to select PS AS mode Press the DISP button 0 again to return to preset mode When PS AS mode is displayed press No 2 of the Preset buttons 9 Stations with good reception are automatically stored in preset buttons starting from Preset button 9 After storing 6 stations preset No 1 station is tuned in and auto storing ends A S in the display becomes pink Stations with good reception are stored in the order from the current station to stations with a higher frequency If there are fewer than 6 sta tions with good reception the auto storing returns to the lowest frequency and resumes from there Note e When stations are preset by the auto store func tion the station previously stored in the memory at that position is cleared If there are fewer than 6 stations with good reception the stations previ ously stored at the remaining preset buttons are not cleared 2 Preset scanning Note This function is not available when the display is stored 1 Press the BAND button 8 to select a band 2 Press the DISP button 10 to select PS AS mode Press the DISP button f0 to return to preset mode In PS AS mode when No 1 of the Preset but tons 9 is pressed the preset stations are tuned in for 5 seconds each P S in the display becomes pink When a preset station has been tuned in preset scanning starts from the station after the current
6. Do not disassemble or modify the set in any way Doing so may result in damage A WARNING THIS PRODUCT IS NOT INTENDED FOR VIEWING TELEVISION BROADCASTS OR VIDEO TAPES OR FOR PLAYING VIDEO GAMES Such uses of this product may distract the driver or interfere with the dri ver s safe operation of the motor vehicle and may violate state law CLARION DIS CLAIMS ANY LIABILITY FOR ANY BODILY INJURY INCLUDING FATALITIES OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY SUCH UNINTENDED USES OR FROM ANY IMPROPER USE OF THIS PRODUCT Do not draw the LCD panel out and use it as a tray Also subjecting the LCD panel to shocks may result in breakage deformation or other damage e Do not let cigarettes burn the display Doing so may damage or deform the cabinet Y If a problem should occur have the set inspected at your store of purchase Do not insert objects or poke in the space between the LCD panel and the source unit when the panel is tilted Do not place anything on the display when the LCD panel is tilted e Do not hold on the LCD panel when adjusting the angle of the LCD panel Doing so may damage it In extremely cold weather the movement of the picture may be slow and the display may be dark but this is not a malfunction The set will work normally once the temperature increases Cleaning e Cleaning the cabinet Use a soft dry cloth and gently wipe off the dirt For tough dirt app
7. No 1 HAL HALL Sound setting simulating a large hall Sound setting simulating a big church with a very high ceiling Sound setting simulating a large stadium with no fence or ceiling Sound setting simulating No 4 LVH LIVE HOUSE a live house slightly larger than a jazz club Sound setting simulating a disco where the bass is emphasized Sound setting simulating No 6 JAZ JAZZ CLUB a jazz club with a low ceiling No 2 CHC CHURCH No 3 SDM STADIUM No 5 DIS DISCO lt DSP BASIC2 gt only for DPH9100 No 1 DOM DOME Sound setting simulating an indoor sports ground No 2 CHM CHAMBER Sound setting simulating a grand chamber of a court No 3 PRK PARK Sound setting simulating a large outdoor field Sound setting simulating a movie house or theater Sound setting simulating a listening room Vocal sound is eliminated No 4 THE THEATER ios STU STUDIO No 6 BGM BGM lt DSP USER gt only for DPH9100 No 1 US1 DSP U 1 No 2 US2 DSP U 2 No 3 US3 DSP U 3 No 4 US4 DSP U 4 No 5 US5 DSP U 5 No 6 US6 DSP U 6 Set by the user Set by the user Set by the user Set by the user Set by the user Set by the user Note e Turn on the DSP effect after following instructions in the next subsection Turning on and off the DSP effect Otherwise the above set
8. left or right to adjust the balance 5 Press I center of the ENT button 1 to enter the adjustment or wait for about 5 sec onds The display returns to the listening position adjustment mode Changing the DSP characteristics The DSP creates the surround effect in the cabin space without deteriorating sound quality through digital signal processing Selecting the sound setting menu The sound setting menu can be selected from the provided DSP menu or from the DSP char acteristics selected by yourself Notes eThis function is available only when the DPH9100 DPH7100 is connected e If the control is idle for about 5 seconds after each operation the unit returns to the previous mode 1 Press the DSP button 13 to select the DSP mode 2 Press the BAND button 8 to select DSP BASIC or DSP USER When the DPH7100 is connected only the DSP BASIC menu same as the DSP BASIC1 for the DPH9100 is displayed Each time you press the BAND button DSP menu changes in the following order E DSP BASIC1 DSP BASIC2 DSP HSER DSP BASIC1 2 Each menu consists of 6 char acteristics initially set This menu is an adjustment menu to be set by the user for setting the menu see the next subsection Setting your own DSP characteristics DSP USER 3 Press one of the Preset buttons 9 No 1 to No 6 and select the DSP menu to be set lt DSP BASIC1 gt for DPH9100 DPH7100
9. 0 C to 140 F 60 C The power was turned off when driving on bumpy roads Severe vibration to the operation panel activated the DCP s sensor Press the POWER button 7 again to turn the power on Colors are pale or hue is poor COLOR tone of color and HUE are not adjusted appro priately Select the CONFIGURATION display and a just the color and hue density using the COI OR and HUE controls Spots or stripes on picture Interference signals This may be caused by interference from other cars trains high voltage lines neon lights etc Check again in another place The compact disc does not enter There is already a compact disc inside the disc insertion slot Eject the compact disc and then insert another one The compact disc soon comes out again The compact disc has been inserted upside down Insert the compact disc with the labeled side facing up Sound skipping noise and other noise are heard The compact disc is dirty Wipe the compact disc with a soft cloth The compact disc is severely scratched or warped Replace the compact disc with one that is in good condition The sound is poor imme diately after switching on the power When the car is parked in a humid place dew might form on the internal lens Turn the unit on and wait for about 1 hour be fore operating 33 10 ERROR DISPLAYS If an error
10. 5 to return to the pre vious mode 5 In radio mode press the VISUAL button 18 to switch to the camera mode In CD chang er mode press the VISUAL button 8 twice and go to the camera display In camera mode the illumination colour of the VISUAL button 18 changes If green illumina tion is selected the VISUAL button lights amber if amber illumination is selected the VISUAL button lights green When sound is set to MUTE PAUSE the VISUAL button 18 alternates between amber and green Note e When you shift into the reverse gear the rear vision camera is automatically turned on To cancel the rear vision camera change ON to OFF of the CCD in step 3 above Connecting an external monitor An output terminal for an external monitor is pro vided on the back of the unit to connect an exter nal monitor 1 Press the ADJ button 5 to select the CON FIGURATION display 2 Slide the Up Down button 1 to W down or A up to move the cursor to MONITOR gt mo A 3 Slide the Up Down button 1 to right and switch AUDIO to VISUAL Slide the Up Down button OQ to right again to return to AUDIO AUDIO Display becomes black VISUAL The rear vision camera is monitored on the display Applicable only when the rear vision camera is con nected When It has not been con nected display becomes black in radio CD or ISR mode
11. e When the DPH9100 DPH7100 or EQH5100 is connected to the source unit the tone cannot be adjusted as in the regular mode The DSP and EQ can Adjust the listening position when the DPH9100 or DPH7100 is connected Set the sound setting when the DPH9100 or DPH7100 is connected Adjust the sound range when the DPH9100 DPH7100 or DQH5100 is connected Enter titles when the DPH9100 is connected Adjusting the listening position By adjusting the sound propagation time based on seat position a natural sound setting can be created Notes This function is available only when the DPH9100 DPH7 100 sold separately is connected e If the control is idle for about 5 seconds after each operation the unit returns to the previous mode 1 Press the AM button 3 to change the dis play to the listening position adjustment mode Slide the Up Down button 4 to Y down or A up to select the listening position Each time you slide the Up Down button 1 the adjustment position changes as follows The selected position is displayed in white FULL SEAT Center of the cabin space X FRONT R Right side of the front seats FRONT L Left side of the front seats FRONT Center of the front seats REAR Center of the rear seat POSITION PASS Usual adjustment 26 3 Press gt II center of the ENT button 4 to select the balance adjustment mode 4 Slide the Up Down button T to A up Y down lt
12. to A up and V down to change each set value 2 in the table on the next page Note e The sound setting menu DSP BASIC1 has already been set in DSP USER amp S 27 Adjustment Description Remarks Slide the button to amp up or down to EFFECT _ set the sound reflection ratio 0 to 100 Slide the button to A The BGM type INITIAL UP or Y down to pattern s in the DELAY set the distance from DSP menu can the sound source not be adjusted 1 ms to 100 ms hoy the Baan to amp Only the rever up or down to bration type PEERB set the reverbration pattern 4 in the time DSP menu can 0 3 sto 10 0 s be adjusted Sige the purion R A Only the early up or down to reflection type ROOMSIZE Set the sound pattern Sin the expansion DSP menu can 0 1 to 1 0 be adjusted Slide the button to A Only the rever up or down to bration type set the reverbration pattern in the HIGH ratio for high DSP menu can frequency sounds be adjusted 0 1 to 1 0 Slide the button to A Only the early up or down to reflection type LIVENESS adjust the echo pattern 5 in the 0 to 10 DSP menu can be adjusted The BGM type pattern indicates BGM in BASIC2 The reverbration type pattern indicates HALL and CHURCH in BASIC1 and DOME and CHAMBER in BASIC2 5 The early reflectio
13. PRECAUTIONS 1 This set is exclusively for use in motor 4 Driving on extremely bumpy roads which vehicles with a 12V power supply nega cause severe vibration may cause the tive ground sound to skip 2 Do not operate the set in ways other than 5 This unit uses a precision mechanism those described in this owner s guide In Even in the event that trouble arises addition the LCD pane s opening closing never open the case disassemble the mechanism is delicate so do not operate unit or lubricate the rotating parts or use it with excessive force 3 When the inside of the motor vehicle is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible If moisture forms on the disc wipe it off with a soft cloth If moisture forms on the optical parts of the player do not use the player for about one hour and the condensation will disappear naturally to allow normal operation USE OF CONTROLS ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL A WARNING THIS PRODUCT IS NOT INTENDED FOR VIEWING TELEVISION BROADCASTS OR VIDEO TAPES OR FOR PLAYING VIDEO GAMES Such uses of this product may distract the driver or interfere with
14. White External Amplifier sold separately Hed Sub Woofer ee separately 13 pin C BUS cable Gp DINIbag attached to the CD changer attached Source Unit eee ae Clarion i CD Changer 1 sold separately Tuner Amplifier 4 Unit 1 1 The switch Normal DSP equalizer on the tuner amplifier unit should be set to N N D I 9 Radio antenna terminal on vehicle 3 RCA lead Audio sold separate RCA lead Audio sold separate 2 An external amplifier other than the tuner amplifier unit can be connected In this case connect the speakers to the external amplifier sold separately 3 Use the attached antenna extension lead to connect the radio antenna terminal on the External Amplifier vehicle and the tuner amplifier unit sold separately 2 A WARNING Attached leads for the power supply and speakers This product must be installed and used only in accordance with these instructions DO NOT CONNECT A TELEVISION TUNER TO THIS PRODUCT OR OTHERWISE ALTER THIS PRODUCT SO THAT IT CAN BE USED FOR RECEIVING TELEVISION BROADCAST SIGNALS OR FOR PLAYING VIDEO TAPES OR VIDEO GAMES Any alteration of this product that enables it to be used in ways other than those provided for in this manual could distract the driver and result in an accident for which the installer may be held liable CLARION DISCLAIMS ANY LIABILITY THAT MAY RESULT F
15. cancel the ISR function press the ISR but ton 6 or FUNC button 7 The ISR function is canceled and the previous mode returns Area change When you listen to the radio outside the U S use this function Switchable frequency setting This car stereo is initially set to tune in frequen cy intervals of 10 kHz for AM and 200 kHz for FM the standard calibrations in the U S When using the unit outside the U S use the following procedure to switch the frequency range The table below lists the frequency specifica tions for the U S and other countries Otte Initial Setting New Setting _ U S standard outside U S Frequency spacing 10 kHz 9 kHz AM F requency range 530 to 1710 kHz 531 to 1629 kHz Frequency spacing 200 kHz 50 kHz Frequency range 87 9 to 107 9 MHz 87 5 to 108 MHz 17 Changing area Note e This function is not available when the display is stored Depending on whether you use the unit in the USA and OTHER switch the area as follows 1 Press the ADJ buttot to go to the CON FIGURATION display 2 Slide the Up Down button 4 to A up or wW down and move the cursor to AREA 3 Slide the Up Down button 1 to right to switch the area between in the USA and OTHER Set the USA usually 4 Press the ADJ button 15 to return to the pre vious mode The new setting returns to the initial setting 18 CD Changer Mode Operations
16. connected to the source unit loudness cannot be adjusted See the subsection Setting the auto loudness effect page 28 to adjust loudness Press the LD button 3 for about 1 second The loudness effect turns on and off When the loudness effect is turned on LD appears in the display Setting the clock Note This function is not available when the display is stored 1 Press the ADJ button 15 to go to the CON FIGURATION display 2 Slide the Up Down button 1 to Y down or A up and move the cursor to CLOCK 3 Press gt II center of the ENT button 1 to go to clock setting mode bss 4 Slide the Up Down button 1 to 4 left right A up or W down to set a time Increments the figure Selects the hour Decrements the figure Selects the hour the hour becomes blue and can be changed Selects the minute the minute becomes blue and can be changed The hour or minute increments while the corresponding figure is blue Y The hour or minute decrements while the corresponding figure is blue 5 After adjusting the time press I center of the ENT button 4 to set it Pressing gt II center of the ENT button T resets the second to zero 6 Pressing the ADJ button 15 returns the mode to the previous one gt VY A Notes e The time is always displayed in radio and CD changer modes e When the clock mode is turned on when the dis p
17. dB Slide the Up Down button 1 to A up a or down to select the magnitude of L vibration 1 3 5 7 20 1 To move the cursor to the next item slide the Up Down button 1 to right and to the previous item slide the button to lt left If you slide and hold the Up Down button T to lt left the adjustment menu returns 2 Select REAR or FRONT of P EQ in the EQ ADJ display beforehand Turning on and off the surround effect Slide the Up Doun button T to gt right to turn on and off the surround effect Titling the DSP and equalizer menu Note e This function is available only when the DPH9100 sold separately is connected 1 Press the DSP button 13 or the EQ button 14 whichever you want to title 2 Press the BAND button 8 and one of the Preset buttons 9 No 1 to No 6 to select a user No to be titled 3 Press the TITLE button 16 when the menu is displayed to go to the title input display To enter a title see the subsection Titling page 24 Press the TITLE button 6 to cancel the titling Note Up to 11 characters can be entered in one title 31 9 TROUBLESHOOTING Sympton Power does not switch on There is no sound produced Replace the fuse with one of the same rating 0 5 A or 10 A for this unit If the fuse blows again contact the store where you purchased the u
18. occurs the type of error is displayed Take the measures described below to eliminate the problem ERROR 1 Memory error This error occurs if the disc loading data etc is lost due to wear of the CD auto changer s battery Remove all the discs from the magazine insert the empty mag azine and press the eject key to return to the first disc ERROR 2 Mechanical error This error occurs if there is a problem with the mechanism and the eject or disc selection operation is not completed in the speci fied amount of time Consult the nearest Clarion service shop or customer clinic ERROR 3 Functional error This error occurs if the pickup cannot focus after several tries due to scratches on the disc signal interference etc Replace the disc ERROR 6 Disc error This error occurs when the disc is loaded upside down Reload the disc properly TEMP ERROR Temperature error This error occurs when the CD mechanism s temperature sensor detects that the temperature is too high lems When the temperature returns to normal playback starts 34 FM Tuner Frequency range 87 9 MHz to 107 9 MHz 87 5 MHz to 108 MHz Usable sensitivity 12 dBf new IHF 50 dB quieting sensitivity 18 dBf new IHF Signal to noise ratio IHF A 70 dB Frequency response 30 to 15 kHz 3 dB Stereo separation 35 dB 1 kHz 60 dBf AM Tuner Frequency range 530 kHz to 1710 kHz 531 kHz to 1629 kHz Usable
19. resumes amp Repeat play This function plays the current track track repeat or the current CD disc repeat repeatedly 1 Press the DISP button 0 to select SCN RPT RDM mode 2 Press No 2 of the Preset buttons 9 to start track repeat or press it for about 2 seconds to start disc repeat 19 RPT becomes pink and T RPT or D RPT appears in the display To cancel track repeat or disc repeat press No 2 of the Preset buttons 8 again Playback resumes Random play This function plays all the tracks on the current CD track random or plays the all CDs in the magazine disc random in random order 1 Press the DISP button 10 to select SCN RPT RDM mode 2 Press No 3 of the Preset buttons 9 to start track random or press it for about 2 seconds to start disc random RDM becomes pink and RDM or D RDM appears in the display 3 When a track that you want to listen to is played press No 3 of the Preset buttons 9 again to resume playback Switching the magazine Note This function is not available with the CD changer storing 6 CDs Press the MAGA button 8 to select a maga zine Each time you press the MAGA button 8 the magazine switches in the following order Cc Magazine 1 Magazine 2 Magazine 3 when a CD changer ngad 3 magazines is connected Playback sta
20. sensitivity 28 dB uV Signal to noise ratio 50 dB monaural Audio Amplifier Rated power output 14 W x 4 20 Hz to 20 kHz 1 4 Maximum power output 30 W x 4 EIAJ Speaker impedance 4 Q 4 to 8 Q LCD Display Screen size 5 inch 4 102 mm Width x 2 15 16 74mm Height Display method Transmission type TN liquid crystal display Drive method TFT thin film transistor active matrix driving Pixels 224 640 960 x 234 General Power source voltage 14 4 V DC Ground Negative Current consumption 4 0 A 1 W Dimensions source unit 7 178 mm Width x 2 50 mm Height x 6 1 8 156 mm Depth Dimensions tuner amplifier unit 7 178 mm Width x 1 1 2 38 mm Height X 7 3 4 196 mm Depth Weight source unit 3 30 Ib 1 5 kg Weight tuner amplifier unit 2 42 Ib 1 1 kg inch Source Unit Unit mm 6 1 8 156 mm ji 6 13 1 172 mm zs 178 mm 30 mm a r g 3 3 Tuner Amplifier Unit y 1 1 2 178 mm i Notes Specifications comply with EIAJ Standards Specifications and design are subject to change with out notice for further improvement fakin VRX8271 Installation Wire Connection Guide Contents OMNOANPON HA v BEFORE STARTING risasi PACKAGE CONTENTS CAUTIONS ON INSTALLATION INSTALLING THE SOURCE UNIT REMOVING THE SOURCE UNIT CAUTIONS ON WIRING WIRE CONNECTIONS
21. title 1 Select the mode where the title you want to change is stored radio or CD changer mode 2 Press the TITLE button 16 to select the title input display Change the title using the procedure described in step 3 above and in the sub section Entering a title page 24 Selecting the title 1 Select the mode where the title you want to select is stored radio or CD changer mode 2 Press the TITLE button 16 twice to select the TITLE SELECT display The entered titles appear after the title numbers In CD mode the TITLE SELECT display can not be selected In radio mode slide the Up Down button 1 to lt left or gt right to select a band Slide the Up Down button T to W down or up to move the cursor to the title to be selected Press gt II center of the ENT but ton T to tune in to the selected station Press the TITLE button 16 twice to quit the TITLE SELECT display 3 25 Operating the DSP and Equalizer Notes To use the functions described in this section the DSP Digital Sound Processor DPH9100 or DPH7100 sold separately or the EQ Equalizer EQHS5100 must be connected to the source unit Also some functions are restricted to certain con nection units Therefore the model numbers of the units which incorporate each function are indi cated in the instructions hereafter e The functions described in this section are not available when the display is set
22. when the DPH9100 DPH7100 is connected Note e The setting for the sub woofers cannot be preset in USER1 to 6 Adjusting the parametric equalizer Frequency characteristic in the cabin space can be adjusted The items shown in the table below can be adjusted Press II center of the ENT button 7 to out put the TEST TONE PINK NOISE in the follow ing order e FRONT gt REAR gt ALL eles The preset selection display appears first Note e The settings made for the parametric equalizer cannot be preset in USER1 to 6 Items 1 Description Slide the Up Down button 4 to A up FRONT se or down to select one out of 6 pa PRESET rameters according to the vehicle type TYPE to TYPE6 Slide the Up Down button T to A up REAR 2 or W down to select one out of 7 PRESET parameters according to the vehicle type TYPE1 to TYPE7 Slide the Up Down button 7 to A up or Y down to select the band to be BAND adjusted Select 1 and 2 to adjust the bass and 3 and 4 to adjust the treble and mean 1 to 4 Slide the Up Down button 1 to A up or down to select the range of the FRE frequency to be adjusted QUENCY Set BAND1 and 2 to select the frequency range between 20 Hz and 500 Hz or set BANDS and 4 to select the range between 630 Hz and 20 kHz Slide the Up Down button 1 to A up GAIN or down to adjust the sound level 12 dB to 12
23. C button 7 the operation mode changes as follows f CD changer mode Radio mode When the CD changer is connected tad Press and hold the FUNC button 7 for about one second to turn off the power Slide the Up Down button T to A up or W down to adjust the volume A Increases the volume Y Decreases the volume The volume level indicated is in the display in a range from 0 minimum to 33 maximum 2 Note e In the CONFIGURATION or BALANCE display the volume cannot be adjusted While driving keep the volume to a level at which external sounds can be heard 12 Note Be sure to read this chapter referring to the front diagrams of chapter 2 CONTROLS on page 5 spread A WARNING THIS PRODUCT IS NOT INTENDED FOR VIEWING TELEVISION BROADCASTS OR VIDEO TAPES OR FOR PLAYING VIDEO GAMES Such uses of this product may distract the driver or interfere with the dri ver s safe operation of the motor vehicle and may violate state law CLARION DIS CLAIMS ANY LIABILITY FOR ANY BODILY INJURY INCLUDING FATALITIES OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY SUCH UNINTENDED USES OR FROM ANY IMPROPER USE OF THIS PRODUCT Opening and turning the display 1 Press the OPEN button 5 to open the Display 2 Notes e Do not place any object on the open display Do not drop any object on the movable part e Do not expose the display to shocks If the display is left horizonta
24. EQ button 14 to go to the equaliz er mode 2 Press the BAND button 8 to select EQ USER 3 Press gt II center of the Up Down button 1 when the EQ USER is displayed 4 Slide the Up Down button 1 to lt 4 left or gt right to select the frequency and slide to A up or W down to adjust the sound level Repeat the above procedures to set the char acteristics The frequency selection option differs accord ing to the connection unit as follows DSP EQ type Sound level to Frequency to be be adjusted selected DPH9100 30 50 Hz 100 Hz 12 dB to DPH7100 200 Hz 400 Hz 12 dB 1 kHz 3 kHz 12 kHz 30 Hz 60 Hz 120 Hz 15 dB to EQHS100 200 Hz 15 dB 400 Hz 1 kHz 3 kHz dB to 8 kHz 12 kHz 12 dB 5 After setting the characteristics press and hold one of the Preset buttons 8 No 1 to No 6 where you want to store the setting A beep sounds when the setting is stored 6 Press the EQ button A to return to the pre vious mode 29 Other equalizer settings Basic settings The following items can be set for the equalizer No of sub woofers STEREO MONO OFF SUB WOOFER when sub woofers are connected Lowest frequency 30 Hz 50 Hz EQ MINFREQ when the DPH9100 or DPH7100 is connected Parametric equalizer adjustment FRONT REAR OFF P EQ when the DPH9100 is connected Turning on and off the surround effect ON OFF SU
25. ROM A FAILURE TO INSTALL AS INDICATED IN THESE INSTRUCTIONS 45 E Sample System 2 DSP or Equalizer is con RCA lead Audio sold separately RCA lead Audio sold separately 20 pin DIN lead attached Yellow Red White nected Clarion Rear Vision Camera sold separately o p Clarion Power Box sold separately Connect to the exclusive CCD expansion 13 pin C BUS cable attached to the CD changer Tuner Amplifier Unit 1 9 Radio antenna terminal on vehicle 3 Front Speakers sold separately Source unit Clarion CD Changer sold separately Clarion O e C Rear Speakers sold separately Attached leads for the power supply and speakers 1 Clarion Expand DSP EQ sold separately Black Q GENERAL CAUTIONS 2 3 digital optical fiber cable sold separately 2 RCA lead Audio sold separately The switch Normal DSP equalizer on the tuner amplifier unit should be set to D The AUDIO OUT IN terminal on the tuner amplifier unit can be used only for the audio input not output ND Ll The sound can be improved by using a dig ital optical fiber cable sold separately to connect the Clarion CD changer and the DSP EQ Use the att
26. RROUND when the EQH5100 is connected Note e If the control is idle for about 5 seconds after each operation the unit returns to the previous mode 1 Press the EQ button 14 to go to the equaliz er mode 2 Press the ADJ button i5 to display the set ting menu 3 Slide the Up Down button 1 to A up and V down to select the item and slide the Up Down button 1 to right to change the setting The following items can be set SUB WOOFER STEREO MONO OFF Switches the settings according to the no of speakers EQ MINFREQ 30 50 Sets the lowest frequency P EQ FRONT REAR OFF Switches the front and rear SURROUND ON OFF Tums on and off the surround effect When setting the item SUB WOOFER or P EQ in PUSH ENT if you press gt II cen ter of the ENT button 1 the adjustment mode is set For information about the adjust ment mode of each item see the next sub section Setting in the adjustment mode 4 After completing the setting press the EQ button to return to the previous mode 30 Setting in the adjustment mode Note e When the sub woofer or parametric equalizer is turned off it cannot be adjusted Select an item to be adjusted following step 3 in the previous subsection Basic settings and press gt II center of the ENT button 1 The setting mode is displayed and each adjustment window is displayed Slide or press the Up Down button T followin
27. SAMPLE SYSTEMS GENERAL CAUTIONS A WARNING This product must be installed and used only in accordance with these instructions DO NOT CONNECT A TELEVISION TUNER TO THIS PRODUCT OR OTHERWISE ALTER THIS PRODUCT SO THAT IT CAN BE USED FOR RECEIVING TELEVISION BROADCAST SIGNALS OR FOR PLAYING VIDEO TAPES OR VIDEO GAMES Any alteration of this product that enables it to be used in ways other than those provided for in this manual could distract the driver and result in an accident for which the installer may be held liable CLARION DISCLAIMS ANY LIABILITY THAT MAY RESULT FROM A FAILURE TO INSTALL AS INDICATED IN THESE INSTRUCTIONS 1 BEFORE STARTING 1 This set is exclusively for use in cars with a negative ground 12 V power supply 2 Read these instructions carefully 3 Be sure to disconnect the battery termi nal before starting This is to prevent short circuits during installation Figure 1 Car battery Figure 1 37 2 PACKAGE CONTENTS Source unit Tuner amplifier unit Manuals Owner s Guide amp Installation Warranty card Connection lead for the source unit and the tuner amplifier unit Antenna extension lead Power supply lead for the tuner amplifier unit Parking sensor extension lead orange Extension lead for rear vision camera white red Bag for accessories of the source unit No 1 Flat head screw M5 x 8 Sems hexagonal
28. TUNER S INCH COLOR LC DISPLAY WITH CD CHANGER DSP EQ CONTROL Clarion VRX8271 Owner s Guide amp Installation Thank you for purchasing the Clarion VRX8271 Please read this Owner s Guide amp Installation in its entirety before proceeding with wire con nection and installation After reading this manual be sure to keep it in a handy place e g glove compartment If you sell the motor vehicle please leave the manual in it so that the new owner can use it Read the contents of the enclosed warranty card and keep it with this manual The section CD Changer Mode Operations of this Owner s Guide provides the operation pro cedure of a CD changer which is connected to VRX8271 by C BUS cable If you buy the CD changer only it is accompanied only by its owner s guide The operation guide of the CD changer is included in this Owner s Guide Contents English aS SN aw PRECAUTIONS CONTROLS FEATURES MODE DISPLAY HANDLING COMPACT DISCS BUTTON TERMINOLOGY First Finger Control Operatior CAUTIONS ON HANDLING Cleaning OPERATION Basic Operations Radio Mode Operation CD Changer Mode Te Rear Vision Camera Other Functions Operating the DSP and Equalizer TROUBLESHOOTING 0 ERROR DISPLAYS 1 SPECIFICATIONS e Installation Wire Connection Guide 37 1
29. ached antenna extension lead to connect the radio antenna terminal on the vehicle and the amplifier unit 1 Do not open the case There are no user ser 2 viceable parts inside If you drop anything into the unit during installation consult your dealer or an authorized CLARION service center 46 Use a soft dry cloth to clean the case Never use a rough cloth thinner benzine or alco hol etc For tough dirt apply a little cold or warm water to a soft cloth and wipe off the dirt gently
30. bolt M5 x 8 4 Bag for accessories of the source unit No 2 Hook plate 7 Zip tie Spacer Mounting screw Bag for accessories of the tuner amplifier unit Mounting bracket se Plastic blind clip Mounting screw M4 x 8 Universal mounting bracket DCP case 3 CAUTIONS ON INSTALLATION 1 Prepare all articles necessary for installing the source unit before starting 2 This model is used with the LCD panel slid forwards shell loading system On some types of cars the LCD panel may touch the dashboard or shift stick in which case it can not be installed Check that the set will not hamper operation of the shift stick before choosing the place of installation Figure 2 Dashboard rd Shift stick Shift stick check that it does not touch the LCD Figure 2 3 Install the unit within 30 of the horizontal plane Figure 3 Max 30 Figure 3 38 4 If you have to do any work on the car body such as drilling holes consult your car dealer beforehand 5 Use the enclosed screws for installation Using other screws can cause damage Figure 4 Chassis Chassis _ Max 5 16 8 mm Figure 4 6 The source unit has mounting screw holes for NISSAN N marks and TOYOTA T marks vehicles and for Clarion installation kit C marks When you use a mounting kit sold separate ly affix the screws to the marks above according to the type of the veh
31. button is being held gt Moves forward 3 times faster than normal play when you slide it for about 1 second and 15 times faster than normal play when you slide it for 5 seconds or longer 4 Moves backward 3 times faster than nor mal play when you slide it for about 1 sec ond and 15 times faster than normal play when you slide it for 5 seconds or longer Note e Slide the Up Down button 1 to P right or lt left for 1 second or shorter to switch the tracks 2 Release the button when you reach the desired track to start playback Pausing playback 1 Press II center of the ENT button T to pause playback PAUSE appears in the display 2 Press Il center of the ENT button 1 again to resume playback Scan play This function plays the first 10 seconds of all the tracks on the current CD track scan or first 10 seconds of the first track of all the CDs in the CD changer disc scan 1 Press the DISP button f0 to select SCN RPT RDM mode 2 Press No 1 of the Preset buttons 9 to start track scan Scanning starts from the next track of the current one Press No 1 of the Preset buttons 9 for about 2 seconds to start disc scan Scanning starts from the next disc of the current one SEN becomes pink and TSCN or B SCN appears in the display Turning off the power cancels scan play Press No 1 of the Preset buttons 9 when you reach the track you want to listen to Playback
32. e 4 left Bass is attenuated gt right Bass is emphasized A up Treble is emphasized down Treble is attenuated 3 Press the AM button 3 to return to the pre vious mode Adjusting the balance Note e If no operation is made for about 5 seconds after each operation the unit returns to the previous mode and the settings made are stored 1 Press the AM button 3 to go to the tone adjustment mode 2 When the tone adjustment mode is dis played press the following buttons to switch to the balance adjustment mode When the display is open Press it cen ter of the ENT button 1 When the display is closed Press the AM button 3 BL balance of right and left speakers and FD fader balance of front and rear speakers are displayed in the Information Panel 5 Balance of the front and rear speakers Balance of the left and right speakers Slide the Up Down button 1 to lt 4 left gt right A up or W down to adjust the balance of the speakers 4 Increases the volume of the left speaker gt Increases the volume of the right speaker A Increases the volume of the front speaker Increases the volume of the rear speaker 2 14 Loudness Notes e When the DSP or equalizer unit DPH7100 or EQH5100 sold separately is connected to the source unit the loudness effect cannot be select ed e When the DSP unit DPH9100 sold separately is
33. ec tion of arrow and remove them Figure 7 Source Unit l 2 Springs Screwdriver 4 Hexagonal screws M5 x 8 K eS a Z Center Panel Note 1 The parts and screws with this mark are used to install radio or included in the installation kit The screws with this mark are originally attached to the vehicle Note 1 In some cases the center panel may require some modification trimming filling etc 40 2 Screws Mounting bracket NG pair for the left and right sides a aia Se 2 Secure the mounting brackets to the chassis as shown in Figure 8 Holes are pre tapped for TOYOTA and NISSAN vehicles modifica tion such as drilling new holes of the mount ing brackets may be required for other mod els 3 Wire as shown in Section 7 4 Secure the unit in the dashboard and then reassemble the dashboard and the center panel os Figure 8 Note 2 If a hook on the installation bracket interferes with the unit bend and flatten it with a nipper or a similar tool m Installing the Tuner Amplifier Unit Before installing the tuner amplifier unit position it considering safety and operability of the entire system Figure 9 Sample installation when the unit is installed under the front seats Install the unit under the front seats using the included parts If there are not enough space under the seats consult the store where you purchased the uni
34. equency stations To stop the seek tuning slide the Up Down button f to lt 4 left or gt right Manual tuning 1 When MANU does not appear in the display press and hold the BAND button 8 for about 1 second to select manual tuning When manual tuning is selected MANU appears in the display 2 Slide the Up Down button T to P right or lt 4 left to tune in to a station Each time you slide the Up Down button T the frequency changes in 0 2 MHz increments for the FM and in 10 kHz increments for the AM band Press and hold the Up Down button 1 to gt right and 4 left to increase or decrease the frequency continuously 16 Preset memory function A total of 24 stations can be preset 6 each for the FM1 FM2 FMS and AM bands Note e When a station is preset the station previously stored in the memory at that position is cleared Manual memory function 1 Press the BAND button 8 to select a band 2 Slide the Up Down button 1 to P right or lt 4 left to tune in to a station 3 Press and hold for about 2 seconds one of the Preset buttons 9 where you want to store the station When a beep sounds the station is stored in that button One station in each band can be preset to each button Auto store function Note e This function is not available when the display is stored 1 Press the BAND button 8 to select a band
35. et ting is made becomes flat 3 Press No 1 to 6 of the preset buttons 9 to select the equalizer characteristic to be set Putton EQ BASIC EQ USER No 1 BAS Bass is ust BASS BOOST emphasized No 2 HIG Treble is us2 HIGH BOOST emphasized No 3 ACO Mean human US3 ACOUSTICAL voice is emphasized No 4 IMP IMPACT Bass and US4 treble are emphasized No 5 SMO Sound level of US5 SMOOTH each band is smoothed No 6 FLA FLAT Original sound US6 fat equalizing Note e Turn on the equalizer effect after following the instructions in the next subsection Turning on and off the equalizer effect Otherwise the above settings will be invalidated Turning on and off the equalizer effect 1 Press the ADJ button 15 to go to the CON FIGURATION mode 2 Slide the Up Down button T to Y down or up to move the cursor to EQ 3 Slide the Up Down button 1 to gt right to turn OFF and ON 4 Press the ADJ button 15 to return to the pre vious mode Setting and storing the equalizer characteristics You can set your own equalizer characteristics and store them to EQ USER US1 to US6 Up to 6 patterns can be stored Notes e This setting cannot be edited when EQ in the CONFIGURATION display is turned off e If the control is idle for about 5 seconds after each operation the unit returns to the previous mode 1 Press the
36. ff the beep sound output during operation 1 Press the ADJ button 5 to select the CON FIGURATION display 2 Slide the Up Down button T to W down or A up to move the cursor to BEEP 3 Each time you slide the Up Down button E to P right the beep sound is turned on and off 4 Press the ADJ button f5 to return to the pre vious mode 24 Titling You can title a radio station or CD name title and store them When the titled station is tuned in or the CD is played its title appears in the display Entering a title Notes Up to 30 FM band and 20 AM band stations can be titled Also 50 CDs can be titled If you try to input more than the specified number of titles OVER FLOW appears in the display and further input becomes impossible Delete unnecessary titles to input new ones e ACD litle can be entered only when it is played 1 Select a station or CD which you want to title 2 Press the TITLE button 6 and select the title input display FM 98 1 P cHe am mom Each time you press the TITLE button i6 the display switches in the following order came input display TITLE SELECT Preset mode TITLE CLEAR 3 Press No 1 and No 2 of the Preset buttons B to select the letter type No 1 of the Preset buttons 9 Upper case letters and figures No 2 of the Preset buttons 9 Lower case letters and symbols Slide the Up Down button 1 to A
37. g the instruction on the display and make setting Adjusting the sub woofer Volume or filter of the sub woofer is set Items shown in the table below can be set Items 1 Description Slide the Up Down button 1 to A up WOOFER or down to adjust the volume of the woofer 0 to 4 Slide the Up Down button T to A up Be or Y down to set the frequency of the low pass filter 60 Hz amp 80 Hz 120 Hz PE Slide the Up Down button 1 to A up or EPG pre down to set the slope of low pass filter 12 dB oct 18 dB oct 24 dB oct Slide the Up Down button 1 to A up hee or down to set the frequency of the high pass filter Through 50 Hz 80 Hz 120 Hz Slide the Up Down button 1 to amp up or HPF V down to set the slope of high pass filter off FRONT L FRONT R SLOP REAR L REAR R WOOFER L WOOFER R ALL ch Slide the Up Down button 1 to amp up or Y down to check the wiring of the speakers TEST off FRONT L FRONT R TONE REAR L REAR R WOOFER L 4 WOOFER R ALL ch 1 To move the cursor to the next item slide the Up Down button 7 to gt right and to the previous item slide the button to lt 4 left If you slide and hold the Up Down button T to left the adjustment menu returns 2 The LPF SLOPE and the HPF SLOPE can be adjusted when the DPH9100 is connected The TEST TONE can be adjusted
38. icle Figure 5 Figure 5 4 INSTALLING THE SOURCE UNIT m Universal Mount 4 Place the universal mounting bracket into the instrument panel use a screwdriver to bend each stopper of the universal mounting bracket inward then secure the stopper as shown in Figure 6 i P i Notes 2 Wite as showniin SECHNON 1 Some car models require special mounting 3 Insert the source unit into the universal kits for proper installation Consult your mounting bracket until it locks Clarion dealer for details 4 Mount the outer escutcheon so that all the 2 Fasten the front stopper securely to prevent hooks are locked the source unit from coming loose Console opening dimensions Instrument panel Source Unit Stoppers So 2 Springs Note Set the outer escutcheon so that its metallic part on the back side fits the upper edge of the source unit Figure 6 39 Fixed Mount TOYOTA NISSAN and other ISO DIN equipped vehicles This unit is designed for fixed installation in the dashboard If the vehicle is equipped with a factory installed radio install the source unit with the parts and screws marked Figure 8 If the vehicle is not equipped with a factory installed radio obtain an installation kit to install the source unit in the following procedure 1 Remove the screws at both sides of the source unit and slide the springs to the dir
39. inal Red AUDIO output right White AUDIO output left NO FADER 1 Yellow Rear vision camera stipe Orange O IS Parking brake lead 7 a White red Rear View of the Source Unit Is Rear vision camera control lead 7 Bleck Ground lead 2 1 range white Illumination power supply lead Attached gem lead Red M Accessory power supply lead 3 DSP EQ RY Yellow a IS Main power supply lead 4 w m Black amp a E Ground lead 2 lue white fi r ZE Amplifier control remote turn on lead 5 Green Purple F Rearlet gt Greenfolack Rear right Tuner Amplifier Unit Purpie black 5 Ta re White ZE Front SA gt Connect to the Speakers J Gray p Wnitelack Front right Graylblack Front left Front right _ Radio antenna terminal JASO 7 Audio output input terminal L R RCA 6 a1 2 3 4 5 6 7 Fader cannot be adjusted with these outputs Connect them to an amplifier sold separately etc Connect securely to the metal part of the vehicle with a screw etc Connect to the power supply terminal whitch can be turned on and off by the ignition switch Connect to the power supply terminal where the power
40. is always supplied regardless of whether the ignition switch is turned on or off Connect to the remote turn on lead of amplifiers Connect to an external amplifier or Clarion expand DSP EQ sold separately etc using the RCA lead L R sold separately Use the attached extension lead when necessary 43 E Connecting the Accessories e Connection to the external amplifier The external amplifier can be connected to the audio output terminal RCA terminal red white on the side of the tuner amplifier unit and the source unit Connection to the rear vision camera for vehicle The rear vision camera for vehicle can be connected to the rear vision camera CCD terminal on the source unit For details refer to the instruction sheet or manual for the rear vision camera Note A power supply box sold separately is required for connection of the source unit and the rear vision camera Connection to the DSP or equalizer The Clarion DSP or equalizer DPH9100 or EQH5100 sold separately can be connected to the connection terminal for the tuner amplifier unit and the audio terminal RCA terminal red white For details refer to the instruction manual for the DSP or equalizer Note When connecting the DSP or equalizer the switch Normal DSP equalizer on the attached tuner amplifier unit should be set to D N D 44 8 SAMPLE SYSTEMS E Sample System 1 RCA lead Audio sold separately
41. ized green is empha sized Press Il center of the ENT button 1 to select what to adjust 4 Brighten BRIGHT is selected Darken 5 Slide the Up Down button 4 to right or lt left to adjust the brightness 22 6 After the adjustment press gt I center of the ENT button 1 to return to the CONFIG URATION display 7 Press the ADJ button 15 to return to the pre vious mode Other Functions Note The following operation is not available when the display is stored Switching the spectrum analyzer display The spectrum analyzer display pattern can be switched in radio or CD changer mode Each time you press and hold the DISP button f0 for about 2 seconds the spectrum analyzer display pattern switches in the following order SPECTRUM Character display REV SPECTRUM MIRROR IMAGE SPECTRUM PEAKS SPECTRUM Character display SPECTRUM mew FM1 90 0 re SPECTRUM PEAKS Notes In ISR mode the spectrum analyzer patterns can not be displayed e The spectrum analyzer turns off temporarily in some mode or during some key operation Switching the button color Button color can be switched between green and amber 1 Press the ADJ button FIGURATION display 2 Each time you slide the Up Down button 1 to P right the button color toggles between green ILLUMI1 and amber ILLUMI2
42. lay is stored after a station is tuned in the fre quency is displayed for several seconds then the time will be displayed Turning on and off the clock display Note This function is not available when the display is stored 14 Press the ADJ button 15 to go to the CON FIGURATION display 2 Slide the Up Down button T to A up or Y down to move the cursor to CLOCK p BE ee ON EA 3 Each time you slide the Up Down button T to P right the clock display turns on and off 4 Press the ADJ button 15 to return to the pre vious mode 15 Radio Mode Operations FM Reception For enhanced FM performance the MAGITUNEEZ tuner includes signal actuated stereo control Enchanced Multi AGC Impulse noise reduction curcuits and Multipath noise reduction circuits Listening to the radio 1 Press the FUNC button 7 to select radio mode 2 Press the BAND button 8 to select a band Each time you press the BAND button 8 the band changes in the following order eS eS a 3 Press one of the preset buttons 9 to tune in to a station Seek tuning 1 While MANU appears in the display press and hold the BAND button 8 for about 1 second to switch to the seek tuning 2 Slide the Up Down button 1 to right or lt left to start the seek tuning When a sta tion is found it is automatically tuned in gt Seeks higher frequency stations lt 4 Seeks lower fr
43. lifier Unit wiring is correct If it is replace the fuse with a new one with A the same amperage rating as the original 4 To replace the fuse release the catch on the 5 When connecting the ground lead fasten the source unit side remove the old fuse and insert the new one Figure 11 Note There are various types of fuse holder Do not let the battery side and touch other metal parts Example 1 Amplifier contro Blue white Example 2 Main power supply Yellow Figure 11 ground lead black securely to a clean metal plate on the car Figure 12 If the set is insufficiently grounded it may not operate or there may be noise Figure 12 After the connection fix the lead by a clamp or insulation tape for protection A WARNING This product must be installed and used only in accordance with these instructions DO NOT CONNECT A TELEVISION TUNER TO THIS PRODUCT OR OTHERWISE ALTER THIS PRODUCT SO THAT IT CAN BE USED FOR RECEIVING TELEVISION BROADCAST SIGNALS OR FOR PLAYING VIDEO TAPES OR VIDEO GAMES Any alteration of this product that enables it to be used in ways other than those provided for in this manual could distract the driver and result in an accident for which the installer may be held liable CLARION DISCLAIMS ANY LIABILITY THAT MAY RESULT FROM A FAILURE TO INSTALL AS INDICATED IN THESE INSTRUCTIONS 42 7I WIRE CONNECTIONS CD changer terminal Rear vision camera CCD term
44. lly in the open posi tion for 10 seconds or longer it is automatically drawn in 2 Turn the display upwards to a good viewing angle When the display is turned upwards a pic ture appears Information panel display dis appears Label rs A gt upwards by holding only the front edge from the label Do not turn the display unless it is complete ly open When adjusting the angle of the display be careful not to let your fingers get caught by the panel or instrument panel of the vehicle Do not hold the part of the display beyond the label see the illustration above 3 To store the Display 12 in the source unit turn it to the horizontal position until a click is heard The display will be stored and the power to the source unit will be turned off automatically Be careful not to let your fingers get caught when storing the panel Mounting and detaching the operation panel The operation panel of this unit is detachable to prevent theft DCP mechanism 1 Move the DCP Lever 4 to the right The operation panel is unlocked and comes out The power is turned off at the same time j 2 Pull the top edge of the Operation Panel m to remove it After removing the panel put it in the attached DCP ae case for protection i DCP case 3 To mount the Operation Panel 11 insert the panel s lower edge into the display edge and push the panel s upper edge until a click is heard
45. ly some neutral detergent diluted in water to a soft cloth wipe off the dirt gently then wipe again with a dry cloth Do not use benzene thinner car cleaner etc as these substances may damage the cabinet or cause the paint to peel Also leav ing rubber of plastic products in contact with the cabinet for long periods of time may cause stains Small black and shiny dots inside the LCD panel are normal for LCD products The LCD panel may stop temporarily when it is opened or closed when the engine is stopped or when it is cold This is not a mal function If this happens repeat the opera tion e Cleaning the LCD panel The LCD panel tends to collect dust so wipe it off occasionally with a soft cloth a Good an The surface is easily scratched so do not rub it with hard objects Scratch LEA 11 8 OPERATION Basic Operations When this unit is turned on starting and stop ping the engine of a car with its volume raised to the maximum level may harm your hearing Be careful about adjusting the volume NOTE Use this unit after starting the engine Turning on the power and adjusting the volume 1 After turning the car s ignition switch on and starting the engine press the POWER button 7 to turn on the power to the unit This unit starts in the mode it was in when the power was turned off last Press the FUNC button 7 to select the oper ation mode Each time you press the FUN
46. n type pattern indicates STADIUM LIVE HOUSE DISCO and JAZZ CLUB in BASIC1 and PARK THEATER and STUDIO in BASIC2 5 After setting the pattern press and hold one of the Preset buttons 9 No 1 to No 6 at which you want to store the pattern A beep sounds when the pattern is set 6 Press the DSP button 13 to return to the pre vious mode Setting the auto loudness effect The auto loudness effect can be turned on and off or adjusted Notes e This function is available only when the DPH9100 sold separately is connected to the source unit If the control is idle for about 5 seconds after each operation the unit returns to the previous mode 28 Turning on and off the auto loudness effect 1 Press the DSP button 13 to go to the DSP mode Press the ADJ button 15 to display the adjustment menu Slide the Up Down button 4 to W down to select A LD ADJ Slide the Up Down button 14 to right to turn on and off the auto loudness effect 5 Press the DSP button 13 to return to the pre vious mode 2 g 4 Adjusting the sound level of the auto loud ness effect The sound level of the auto loudness effect can be adjusted in 11 levels 0 to 10 Notes e in order to make the following adjustments you must turn on the A LD ADJ described in step 3 in the previous subsection e The adjusted sound level canno
47. nit Wiring is incomplete See Installation Wire Connection Guide especially Section 7 Wire Connections of this manual and connect properly Nothing happens when but tons are pressed or the display is not accurate Noise etc is causing the microprocessor to malfunction Press the reset button with the tip of a very fine instrument for about 2 seconds Reset button Tip of a very fine instrument DSP EQ does not operate The switch of the tuner unit is set to N Turn off the ignition switch once and set the switch to D Picture does not appear Parking brake is not applied Check that the parking brake is fully applied Picture has shadow or shadows Signal condition is poor This may be due to signals reflected off mountains or buildings Check again in a different place and direction LCD panel is not drawn in when it is set to the horizontal position Foreign object at back of tray The panel will not be properly drawn in if there is an object on the tray in the TV storage compartment Remove the object Screen is dark Brightness is adjusted too low Check that the brightness is properly adjusted in the CONFIGURATION mode and set it prop erly Usage conditions are poor This may happen if the temperature in the car is below 32 F 0 C or above 140 F 60 C Check again when the temperature is between 32 F
48. ompact disc by the edges Never touch the surface To remove fingermarks and dust use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference pea New discs may have some roughness around the edges The unit may not work or the sound may skip if such discs are used Use a ball point pen etc to remove roughness from the edge of the disc Ball point pen Sy Roughness Note 5 HANDLING COMPACT DISCS Note on Compact Discs Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen Do not use any solvents such as commercially available cleaners anti static spray or thinner to clean compact discs Do not use compact discs that have large scratches are misshapen or cracked etc Use of such discs will cause misoperation or damage No Ra Do not expose compact discs to direct sunlight or any heat source Do not use commercially available CD protection sheets or discs equipped with stabilizers etc These may get caught in the internal mechanism and damage the disc Note Be sure to read this chapter referring to the front diagrams of chapter 2 CONTROLS on page 5 spread 1 Up Down A Up W Down 4 Left Right Buttons ENT Enter 1II Button 12 Information Panel 3 AM Audio Mode Button LD Loudness Button 4 DCP Detachable Control Panel Lever 5 OPEN Button ISR Instant Sta
49. one When a preset station has not been tuned in preset scanning starts from preset No 1 4 When a desirable station is tuned in press No 1 of the Preset buttons 9 to cancel PS AS mode and press the preset button to which the station is to be stored The preset scanning is canceled and you can listen to the station t Preset selection 1 Press the BAND button B to select a band 2 Press one of the Preset buttons 9 to select the stored station Note e In PS AS mode do not perform the preset selec tion excluding the preset scanning In PS AS mode when No 2 of the Preset buttons 9 is pressed the auto storing starts and all the stored stations are cleared ISR memory If an AM or FM station is stored in the ISR but ton it can be directly tuned in by pressing the ISR button from any other mode 1 Press the BAND button 8 to select a band 2 Press the Preset button 9 or the ENT button 1 to tune in to a station you want to store 3 Press and hold the ISR button 6 for about 2 seconds When a beep sounds the display turns to the ISR Instant Station Recall display and the frequency is stored 4 Press the ISR button 6 to return to the pre vious mode Calling the station with the ISR button 1 In any mode pressing the ISR button 6 allows you to tune in to the stored station When the ISR is functioning the ISR display appears The default ISR setting is 87 9 MHz 2 To
50. ormation Panel Band Frequency Seek tuning mode indication Station title j 2 Band Preset No amp anA Oa a ia 40 ELLI sT Frequency Stereo indication Preset Nos _ Current time _ Stereo indication L Manual indication Auto store indication 5 Preset scan indication P 5 lt CD Changer Mode Display gt Display Information Panel Magazine No Disc No Disc No r CD title Track No j CD mode i appears when a j CD magazine is locked Magazine No c gi j ji lt at gt ied maca nisc q TRack Pi igre ses RPA PSN 1 SPECTRUM __ Track No 4 2S amp AJIES i wee AAA Be LOE c A Le Playback time counter fiss _ Stored Disc Nos L Current time L Random play indication RDM _ Playback time counter Repeat play indication BED _ Sean play indication GCN This unit has been designed specifically for play back of compact discs bearing the E8 mark No other discs can be played To remove the compact disc from its storage case press down on the center of the case and lift the disc out holding it carefully by the edges Proper way to hold the compact disc Removing the disc Always handle the c
51. rts from No 1 CD in the selected magazine The selected magazine No DISC No and TRACK No appear in the display h maa os STACK BS Magazine No 20 Locking the magazine 1 Press and hold the MAGA button B for about 2 seconds to play tracks on only the current CD The selected magazine No becomes pink in the display Notes e Even when the magazine is locked pressing the MAGA button 8 switches to the new magazine which is locked e When the magazine is locked scanning and ran dom playback are performed only for the locked magazine 2 To cancel press and hold the MAGA button 8 for about 2 seconds Playback resumes Rear Vision Camera Note e Use this camera as an auxiliary means to check ing obstacles Monitoring the rear vision camera The rear vision camera can be connected to this unit For the power supply of the camera mount the power box sold separately CCA 147 Note e This function is not available when the display is stored 1 Press the ADJ button 15 to select the CON FIGURATION display 2 Slide the Up Down button Olto W down or A up to move the cursor to CCD 3 Slide the Up Down button T to right to change OFF to ON p ELE CONEIGURATION TEUM GOLO e When CCD in the CONFIGURATION display is turned on the setting can be switched even if the camera has not been connected 4 Press the ADJ button
52. t 2 Mounting brackets eee ae blind clips 1 Attach the mounting brackets on the left and right side of the tuner amplifier unit using the attached screws M4 x 8 Figure 9 2 Position the tuner amplifier unit on the floor carpet and drill holes through the carpet at the position where the holes of the bracket fit 3 Push the attached plastic blind clips through the holes on the carpet into the mounting bracket holes Nes 4 Mounting screws M4 x 8 Figure 9 5 REMOVING THE SOURCE UNIT 1 When the back of the source unit has been secured with the method shown in Figure 6 unfasten the special bolt 2 Remove the outer escutcheon 3 Insert the hook plate between the spring and the universal mounting bracket fit tab of the spring into hole of the hook plate then Universal mounting bracket 2 Hook plates o Outer escutcheon pull the source unit out by the hook plate Insert both the right and left edges of the hook plate Figure 10 Note Keep the hook plate You cannot remove the unit without disengaging the hook plate r Instrument panel Figure 10 41 6 CAUTIONS ON WIRING 2 Be particularly careful where you route the Be sure to turn the power off before wiring Antenna wires Keep them well away from the engine and exhaust pipe etc Heat may damage the wires SS a 3 If the fuse should blow check to see if the sf Tuner Amp
53. t be stored in USERI to 6 1 Press the DSP button 13 to go to the DSP mode Press the ADJ button 15 to display the adjustment menu Slide the Up Down button 1 to Y down to select A LD ADJ and press gt II center of the ENT button T to go to the auto loudness effect adjustment mode The adjustment dis play appears Slide the Up Down button Mto a up or Y down to select the sound level Press the DSP button 13 to return to the pre vious mode 2 e 4 5 Modifying the equalizer character istics The equalizer selects the appropriate sound fea tures and frequencies for each type of music Selecting the equalizer characteristics You can select the equalizer characteristics from the provided equalizer menu or from the equal izer characteristics which have been selected by the user Note e If the control is idle for about 5 seconds after each operation the unit returns to the previous mode 1 Press the EQ button 14 to go to the equaliz er mode 2 Press the BAND button 8 to select EQ BASIC or EQ USER Each time you press the BAND button 8 the EQ BASIC and EQ USER toggles EQ BASIC This menu consists of the 6 equalizer characteristics initially set EQ USER The menu containing user set equalizer characteristics for setting the characteristics see the next subsection Setting and storing the equalizer charac teristics The equalizer No where no s
54. the driver s safe operation of the motor vehicle and may vioiate state law CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY INCLUDING FATALITIES OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY SUCH UNINTENDED USES OR FROM ANY IMPROPER USE OF THIS PRODUCT INFORMATION FOR USERS CHANGES OR MODIFICATIONS TO THIS PRODUCT WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL 2 CONTROLS COMMANDES CONTROLES Note Be sure to spread this page and refer to the front diagrams when you read each chapter SOURCE UNIT When the display is closed 22 OO eatin at Ta IAN E Sua St isn Clarion PA B H HE J W 5 inch TFT Active Matrix Drive Type Color LCD Panel Shell Loading Mechanism m Various Character Panels for AM FM Reception CD Display and Equalizer etc E Title memory function storing CD titles and AM FM stations E Environment setting function to select illumination color amber green background color and whether to turn on or off the beep sound Auto Store Function Multiple CD Changer Control RCA Gold plated LINE OUT DCP function enables you to detach the operation panel to prevent theft Available when the CD changer or equalizer sold separately is connected 4 MODE DISPLAY _ lt Radio Mode Display gt Display Inf
55. tings will be invalidated Turning on and off the DSP effect 1 Press the ADJ button 15 and go to the CON FIGURATION mode 2 Slide the Up Down button 1 to Y down or A up to move the cursor to DSP 3 Slide the Up Down button T to right to turn OFF and ON 4 Press the ADJ button 115 and return to the previous mode Setting your own DSP characteris tics Up to 6 DSP characteristics can be set by the user and stored in the DSP USER US 1 to US 6 Notes e This function is available only when the DPH9100 sold separately is connected to the source unit e If the control is idle for about 5 seconds after each operation the unit returns to the previous mode elf DSP is turned off in the CONFIGURATION mode the following instructions cannot be operat ed 1 Press the DSP button 13 to go to the DSP mode 2 Press the BAND button 8 to select DSP USER Press the ADJ button i5 when DSP USER is displayed to select the adjustment menu Press gt II center of the ENT button 1 to go to the DSP EDIT adjustment mode Adjustment items are displayed as shown on the next page To move the cursor to the next item slide the Up Down button T to gt right and to move it to the previous item slide the button to lt lt left If you slide and hold the Up Down but ton 4 to lt left the adjustment menu returns 1 in the table on the next page Slide the Up Down button 1
56. tion Recall Button 2 7 POWER Button FUNC Function Button 8 BAND Button 9 MAGA Magazine Button Preset Buttons 2 Disc No Buttons C1 ca First Finger Control Operation 3 E 2l R E G lal Et Eq El fs amp DISP Display Button Operation Panel Display DSP Digital Sound Processor Button EQ Equalizer Button ADJ Adjust Button TITLE Button MONI Monitor Button VISUAL Button Rear Vision Camera Indicator Receiver for remote control unit In Radio Mode In CD Changer Mode By sliding the Up Down button 1 up amp down right P or left lt you can select various items and make settings This function is called the First Finger Control Operation With this function you can select a menu or track control the volume or change a frequency according to ihe operation mode Press the center of the ENT button 24 T to execute a selected menu play pause or mute on off CAUTIONS ON HANDLING For a longer service life be sure to read the fol lowing cautions iS 10 Be sure to store the LCD panel inside the source unit when parking the car outdoors for long periods of time The LCD panel will operate properly in a tem perature range of 32 F 0 C to 140 F 60 C Don t allow any liquids on the set from drinks umbrellas etc Doing so may damage the internal circuitry
57. up Y down lt q left or PB right to move the pink cursor to the letter you want to enter Press gt II center of the ENT button 4 The selected letter is entered at the cursor black on the top of the display Repeat steps 3 and 4 above to enter the title If you entered the wrong letter press No 4 of the Preset buttons 9 to backspace the cursor black and enter the correct letter this time Press No 5 of the Preset buttons 8 The cur sor black moves to the right E 5 After entering the title press and hold gt II center of the ENT button 1 for about 2 seconds The title is stored when the beep sounds and the previous mode is recalled Notes e The title list of the title select display in radio mode displays only titles for the preset stations After entering a title if you change the reception area inconsistency between the entered title and the frequency occurs Clearing the title 1 Select the mode where the title you want to clear is stored radio or CD changer mode 2 Press the TITLE button 16 to go to the TITLE CLEAR display 3 Slide the Up Down button 4 to W down or A up to move the cursor to the title you want to clear and press and hold 1I center of the ENT button 1 for about 2 seconds The title is cleared when the beep sounds 4 Press the TITLE button 16 to return to the previous mode Changing the
Download Pdf Manuals
Related Search