Cissell HF 234 User's Manual
Contents
1. ccccccccccceceeee eee eeneeeee cette tnaeeeeeeeetiaeeeeeeeenaa 18 6 Technical remarks ccccccccccceceeeeeceeennneeeeeeeeenaeeeeseesenaeeteeeeenaaas 19 Internal connection of the electrical heating ccecceeeeteeeeeetees 19 THES WHC sares meai cetacean sacs iiai E rea EAA AE E EETA 19 EMMOFMCSSAGES ueria ariii a a a a i a 20 7 Maintenance of the machine cccccccecetttte eee eeeentneeeeeeeeeenaaes 22 Code 249 00173 00 19 12 00 Contents General safety instructions Ignoring any of the safety instructions can cause serious personal injury and can also cause damage to the linen or the machine Read the installation and instruction manual carefully before connecting the machine CI is recommended that the machine be installed by qualified technicians E The machine should be installed according to the installation instructions See chapter 3 Ithe machine should be grounded according to the instructions in order to eliminate the risk of electrocution CI Donot expose the machine to high humidity or extreme high or low temperatures cut off all main water inlets steam and electrical supplies at the end of each operating day Cl Before starting repairs or maintenance shut off all power and water supplies To prevent fire and explosion Keep the area around the machine free from inflammable or combustible products Do not put fabrics that are treated with inflammable products into the ma2. Conical coupling MM 1 2 Single window 1 2 One way valve 1 2 M inner wire F outer wire The manufacturer is not responsible for damage or accidents caused by not following the installation instructions Operating instructions Machine with start button Opening the door Fill the drum Close the door Select program g SELECT gt P START gt O W2 eo R CONTROLLED ROLLED Add detergent Push the red button on the door handle to open the door Sort the linen according to the type and required temperature of the linen Empty all pockets of the garments so that no garments can be damaged and no left articles can cause damage to the machine Turn sleeves of shirts blouses inside out It is recommended to mix small and large items to enhance the drop of the linen during the wash cycle and hence improve the wash quality Wash loads of below 80 of machine capacity can obstruct the proper functioning of the machine and can damage the machine Overloading the machine can also lead to a bad wash result On machines with a start button the programmer can contain up to 100 programs 0 99 The program number is displayed on the right display By pressing the SELECT button P the next program will be displayed By pressing the ECO button E the previous program will be displayed By keeping this butto
3. L1 L2 L3 The green yellow grounding clamp has to be connected to the grounding wire PE 380 V3AC N 380 V 3 phase 3AC N has to be connected to the connectors L1 L2 L3 the blue neutral to the N connector The green yellow grounding clamp has to be connected to the groun ding wire PE Cl After connection check the spin direction The cylinder must spin in the direction of the arrow showed on the sticker on the door window clockwise A wrong spin direction can damage the motor and can also cause water to spurt from the soap dispenser CI Incase of wrong spin direction switch the terminal clamps of the motor machine with steam heating or boiler fed machines without additional electrical heating 220V3AC 380V 3AC N 16A 16A machine with electrical heating 220V 3AC 380V 3AC N 12kW 40A 20A 15kW 50A 25A 18kW 50A 32A 21kW 40A 24kW 40A Liquid soap connection option Connection of the liquid soap A rubber connection has been placed over the air break opening at the back hoses of the machine There are 5 holes in this rubber connection through each of whicha liquid soap hose can be driven S1 85 Press the hoses until they appear well inside the soap dispenser The central gap in the rubber connection remains and serves as air breaker Electrical connection of On machines equipped with a liquid soap connection connect the wires the liquid soap pumps directly o
4. cS cissell Expect Great Things Instruction manual HF 176 HF 234 With electronical timer p20 Technical specifications Installation instructions Operating instructions Maintenance A wei amp w d CETE aaa lee w arixct P wis Ge oo start gt o B W 7 Te 831 South First St POB 32270 Louisville KY 40232 2270 Phone 502 587 1292 Fax 502 585 3625 www cissellmfg com Part No D0051 Contents 1 General safety instructions 00 citi e ce eettte tere teeenttateteeeeeenaaes 3 2 Technical data and dimensions cece entice eee eenttetteeeeeenaae 4 TOCHHICAl data o3323 2eceiebs 3 axzzeweteids ieetenen E RESA Mobiaies 4 DIUMGNSIONS 3335 Sedetecttiesiteddenetsi EE 5 3 Installation ANd connection 00 0 0 1 ccc inte e eee tn tte eee t ett ttaeeeeeetee 6 GIOUING ain eel eee ee ee 6 Removing the transport brackets c cccccccteeeseeeeeteeenneeeeeteeeneaeees 6 Water CONNCCHON snee i E EE ATE 6 Water dralft zc sas tiie ea st Sedat ea ee a ide 7 Main POWEr CONNECTION eeceeeeececcteeceeceeeeeeeeeteeeeeeeeeeeeeeetetteeteeeneess 7 Liquid Soap CONNECTION entei eee aa aa 8 Sloan CONMCCUON Saee E E E TE ieee 9 4 Operatinginstructions c icici cect e ee teeentee eee eteneenaeeeeeteennaatees 10 Machine with Start button ccccecccceeeeeee eee eteeeneeeeeeteneenaeeeeeteeeeaanees 10 5 Standard programs
5. spin blinking rapidly slowly slowly off Final spin continuously continuously continuously rapidly Following functions can be activated during the program F1 Time stop Toincrease the duration ofa program segment beyond its originally program med duration F2 Soak To soak heavily soiled linen F3 Reduced wash action To avoid wear of delicate garments F4 Execute high spin as low spin To avoid creasing delicate linen F5 Rapid advance To skip certain program segments F6 No spin To give total protection to delicate garments F7 on the left display appears the number of revolutions of the drum F8 changing the number of revolutions at final spin In order to limit the rpm for delicate linen Selecting a function Push the SELECT button P at the time the special function needs to be activated and keep the button depressed Now push the START button S simultaneously and release same Only now release the SELECT button P The central display now shows F1 and this function is now active By pressing the SELECT button P the next function will appear on the central display And so on up to F8 To return to normal operation press the START button S and release A function is also terminated by selecting another function Functions are also automatically ended and switched off at the end of the each program 12 Description of the functions YR
6. once more you add each time 10 minutes After 50 minutes 1 0 1 1 1 2 etc appear with a maximum of 4 0 hours By means of the START button S you can each time reduce 10 minutes Remark The programmed stop time is executed after the decimal point in the right display has extinguished The stop time cannot be programmed during spin Function F2 soak This function can only be chosen during prewash main wash and first rinse The cycle time is stopped The bath is filled till high water level and heated up to 40 C ifa higher temperature was programmed this will be followed As long as this temperature is not reached the machine makes a reduced wash action shorter action time and longer pause time When the bath has reached its temperature the drum will make one left right rotation every 4 minutes Should the temperature fall the water will be heated again during which the action will be reduced again This function remains active until the START button S is pressed again Programmable soak time In the same way as for the stop time you can program the soak time see programmable stop time 13 g eorsen DY CONTROLLED SELECT gt P 4 SELECT gt P SELECT gt P 4 By selecting F3 the wash action time and pause time will be reversed unless the w
7. with the following program displayed during the shorter time span This function is canceled by pressing the START button S again for at least 5 seconds This function can be combined with an economy wash with the functions F1 to F6 and with a programmed start The freely programmable stop function can however only be executed during the first program Operation Press the START button S to start the programs The central display will show the remaining time per program The total time of both programs together is not displayed The right display alternately shows the program in operation during a longer time span and the second program to be executed during the shorter time span After the first program has been run only the second program number will be displayed Cooldown This function allows to gradually lower the temperature of the wash bath to prevent creasing of the linen During a cool down the remaining program time on the central display will be replaced by cd Power Failure Should the power fall out during the program the water will be drained and the door can be opened after maximum 3 minutes When the door remains locked and the power comes back up within 24 hours the program will continue from there where it was at the time of the power failure Ifdue to breakdown the door is not unlocked automatically you have to remove the service panel A below and pull the ring B suspended on the left si
8. 00002 00 Repair and after sales _ Incase of important malfunctions and deficiencies which you cannot resolve service yourself do not hesitate to contact the technical service of your distributor Data distributor Name ccccccccsccececececsccessceececessceesceetscecseceusecetseecesecenass TENG 0 g gt i0 oe a eR NC ae Data machine Wy G68 sis fas Son curate thie Satay aed i Paice Mla eld aa Programi o Noerdin renerrien dE aAa aiaeeiiee ede EE OASE Date of installation n an a Installed iby aaar sieeee ily eases acer vases eth mae Se flal number niteni tendeni a ee ete Operation voltage and frequency ccceceeeeeeeeetteeeeeeeeentaees The manufacturer reserves the right to change the content of this instruc tion manual at all times and without previous notice ooo gt gt gt
9. 1D253 LC1D0901 3x2kw 1Skw 3x2kw A LC1D253 LC1D1810 3x3kw 18kw 3x3kw A LC1D323 LC1D1810 3x3kw 2ikw 3x3kw wee wee LC1D1810 3x4kw wee ee A LC1D1810 24kw 3x4kw wee A LC1D1810 3x4kw eee ee A LC1D1810 Bre Brown Remark Bu Blue W White Other executions are available as options W B White black W R White red Tilt switch The tilt switch is mounted on the solid part of the machine There is a window around the probe of the tilt switch that is mounted on the movable part of the machine When the machine goes out of balance by overloading or uneven distribution of the linen the tilt switch will interrupt this action to prevent damage to the machine Important To guarantee good functioning the probe should be centered horizontally and vertically at 1 3 from the bottom of the tilt window when machine drum is empty 19 6 Error messages When one of the following malfunctions occurs during a program the central display will communicate the appropriate error message at the end of the cycle E3 Eprom The Eprom is wrong replace it by another Remark For coin op machines it is possible that a program number appears on the right display in combination with E3 This indicates a wrong price adjustment for thi
10. CONTROLLED START gt w g SELECT gt P START s 4 Function F1 Time stop During the wash cycle The wash time is stopped The temperature water level and wash action remain the same as programmed During the wash cycle this function remains active until the START button S is pressed again During intermediate spin The intermediate spin normally lasts 1 minute By activating function F1 the machine will spin for nine minutes unless the START button S is pressed earlier During final spin At final spin you have high spin after low spin By activating F1 during low spin this low spin will be extended tol5 minutes unless the START button S is pressed earlier Ifthe 15 minutes of low spin have been completed the high spin is automatically canceled By activating F1 after the preprogrammed low spin you will have amaximum of 14 minutes of high spin unless the START button S is pressed earlier Adjustable stop time Here you can program a certain stop time The display shows the countdown of this extratime When this time is expired the function will appear automatically and the program will continue Select F1 see above The stop time can be programmed by means of the ECO button E By pressing it once the stop time is programmed for 10 minutes From now onwards FI and 10 appear by turns on the middle display By pressing the ECO button E
11. ary heating X Packing dimensions HxWxD 1650x1020x1150 mm Weight Net 455kg 570 kg Gross 524 kg 630kg Dimensions a Hard water connection 3 4 IB Warm water connection 3 4 Ic Soft water connection 3 4 IP Electrical connection Te Electrical connection clamps Ir Output steam valve Ia Water drain JH Steam connection mle Ventilation soap dispenser Installation and connection Ground The machine must be placed on a flat solid surface metal base concrete or solid ground It is recommended that the machine be anchored on the provided places A in the base especially in case of a plinth see Dimensions 2 The machine must be placed entirely level For easy maintenance it is recommen ded to keep a minimal distance of 600 mm between the wall and the back of the machine If several machines are placed next to each another there should be a minimal distance of 30 mm between each machine Removing the transport brackets To prevent damage during transportation the machine has been equipped with four red transport brackets D to eliminate every possible movement of the tub After the machine has been placed level take off the service and the back panel to remove these transport brackets Important The machine must never be activated befo
12. ash action time was programmed to be shorter than the pause time Example 12 sec action 3 sec pause becomes 3 sec action 12 sec pause 6 sec action 9 sec pause remains 6 sec action 9 sec pause This function does not influence the cycle time the program continues normally and remains active until the START button S is pressed Function F3 reduced wash action Function F4 execute high spin as low spin By activating this function high spin will be automatically replaced by low spin This function does not influence the cycle time the program continues normally and remains active until the START button S is pressed Function F5 rapid advance This function is mostly used by technicians and maintenance staff It allows to the program By pressing and releasing the ECO button E the programs skips to the next segment Attention IfF5 is activated during final spin this segment of the program will be skipped as described above It is however followed by a coast and tumble time to disentangle the linen This special function prevents the user from opening the machine while the drum is still rotating and represents an important safety feature To return to normal operation press the START button S Function F6 no spin This function eliminates all spin action Intermediate spin is replaced by a regular wash action During final spin only the programmed low spin time will be complet
13. chine These fabrics should be hand washed or air dried first C Aiways carefully read and follow the instructions on the packing of detergents Store these products out of the reach of children Always take into account the instructions on the labels of clothes Never allow children to play in the surroundings of a machine Remark CI These instructions surely cannot prevent all risks of accidents It is up to the user to act with the utmost precaution Cl Do not hesitate to contact the dealer in case of a problem Technical data and dimensions Technical data HF 176 HF 234 Capacity dry weight 1 11 16 0kg 21 3 kg 1 10 17 6 kg 23 4kg 1 9 19 5kg 26 0 kg Cylinder Diameter 750 mm 750 mm Depth 399 mm 530 mm Volume 176 Lit 234 Lit Cabinet Height 1505 mm 1505 mm Width 900 mm 900 mm Depth 885 mm 985 mm Front loading Diameter door opening 395 mm 395 mm Door height lower edge Door height center 630 mm 630 mm 820 mm 820 mm Speed Wash 10 50 tr min Distribution 100 tr min Spin 250 500 tr min High spin 500 1000 tr min G force Spin 74 High spin 373 Motors 3 phase 4p 1470 rot min 2 KW 3 kW Drain Depend O Drain 3 Option 2 Water inlet Hard soft hot water amp cool down 3 4 Steam connection Steam connection 3 8 Heating Electric 220 380 V 12 15 18 kW Electric 380 V 24 kW Steam X Boiler fed X Boiler fed with auxili
14. de while opening the door Important Before opening the door check that all the water has been drained from the tub and that the cylinder has come to a complete stop Remotestop function By means of this function no cycles can be selected anymore during a certain period of time e g between 10 p m and 7 a m This time is determined by an extern timer As soon as the last cycle is finished OFF blinking appears on the left display as long as this function is activated 17 Standaard programma s 1 2 3 4 5 6 7 8 9 The machine is standard equipped with 10 programs 0 9 These have been designed in cooperation with specialized detergent manufacturers to obtain the best possible wash results using the most frequently used detergents Program 0 starching is mostly used in very special applications and is therefore not displayed on the front panel 0 Starching 1 RINSE COLD 1 HOT WASH 2 BATHS 40 90 C 2 HOT WASH 1 BATH 90 C 3 COLOUREDS 2 BATHS 40 60 4 COLOUREDS 1 BATH 60 C 5 SYNTHETICS 2 BATHS 40 40 C 6 SYNTHETICS 1 BATH 40 C 7 WOOL 2 BATHS 30 30 C 8 WOOL 1BATH 30 9 CURTAINS 1BATH COLD 18 Technical remarks Internal connections of the electrical heating B Black Gy Grey R Red PU Purple Y Gr Yellow green Heating 3x220V R5 3x380V R5 12kw 3x2kw A LC
15. ed as regular wash action High spin is skipped in its entirety This function influences the cycle time the program continues normally and remains active until the START button S is pressed Function F7 indication of the rpm By using F7 the number of revolutions of the drum rpm appears on the right display Function F8 changing the number of revolutions rpm at final spin By means of F8 the number of revolutions can be changed at high spin The programmed number of revolutions appears on the left display Each time you press the ECO button E the spin decreases with 25 rpm min 500 Eachtime you press the START button S the spin increases with 25 rpm max 999 Remark This function has to be selected before final spin has started 14 End of a program 4 At the end of a program while the door is being released the left display shows End and the Start LED is switched off After that only the right display will continue to show the program number This is the end of the program Premature ending ofthe program By pressing the START button S during the program the Start LED is switched off and the water is drained from the machine As long as the water has notreached the safety level the door will remain sealed and the display will show SLE Safety Level on the left display Afterwards t
16. he display will temporarily show End on the same display and the Start LED will be switched off After that only the right display will continue to show the program number This is the end of the program Remark Ifany attempt is made to interrupt the program prematurely during a spin phase of the program all functions on the display will be temperary replaced by blinking horizontal dashes After that only the right display will continue to show the program number and the door will be released This is the end of the program 5 Iam Remarks SEQ w a wo MICROPROCESSOR CONTROLLED 5 MICROPROCESSOR CONTROLLED SELECT gt START gt wE dE g Se Oe MICROPROCESSOR CONTROLLED SELECT gt START gt O u2 o 4 Freely programmable stop function Before starting a program it is possible to preprogram a time stop in every program segment This function permits special additional functions like adding bleach or extra detergent to the wash bath Programming After selecting the program press the ECO button E and keep it depressed Now push the START button S simultaneously and release same Only now release the ECO button E The left display now shows StO Stop and the right display shows the program number The first program sequence LED is switched on Confirm by pressing the START b
17. n pressed this function will be accelerated Remark Select program 0 by keeping the SELECT button pressed continuously for more than 5 seconds It is recommended to only use detergents with a foam breaker These are often found in the launderette or laundry or can easily be found in retail stores Recommended doses are mentioned on the detergent packing Overdosing of detergents can lead to reduced wash results and overfoaming which can damage the machine Left compartment A Prewash 1st wash Central compartment B Main Wash 2nd wash Right compartment C Final Rinse fabric softener Bottom compartment D Direct access to tub Moderately soiled linen can be washed using the Economy Wash function which reduces the water level of washes and rinses by 20 allowing savings of water and energy Press the ECO button during the wash cycle to activate the economy wash function The ECO LED will lightup At the end of the program the ECO function will be automatically eliminated If the ECO function is required in the following wash cycle as well reactivate this function by repeating the actions described above 10 Start the machine g SELECT gt START e s Indications of program sequence 4 Start the wash cycle by pressing the Start button S and releasing it immediately The door is sealed and the cycle LED lights up During
18. n the print board next to the ground wire connection option Connect as indicated on the wiring diagram The two connectors on the right give a tension of 220V max 4A which can be applied to drive 220V soap pumps If more than 4A is required an external tension will have to be used 6 connections have been provided eQ COLLA oo of which one S6 can be used to drive a waterproofing pump e g for rain PP E cars coats etc Ea COMO SIH S2 HY 53 HR sH s5 H The 220V can be transformed to other values to drive other type soap pumps Example pumps 24V a GOG Also pumps with different operating tension can be combined SMODVODOGOO Lidi dhd Example 5 pumps 220V and pump 24V aH BH SAH H SO With an external tension 24V DC Steam connection NAUK WN PE 3 17 9 10 11 12 With directsteaminjection into the machine Steam pipe Steam cut off valve 3 8 Pipe coupling 3 8 Steam filter 3 8 Magnetic steam valve 3 8 Curve MF 3 8 Steam hose with appropriate pipe coupling 3 8 l Added parts for steam heating with heatexchanger Double pipe coupling 1 2 Condensation accumulator with filter 1 2
19. re removing these transport brackets Water connection The machine is delivered with hoses with 3 4 connections These hoses fit the water inlet valves of the machine and the main water inlet taps To ensure the optimal functioning of the water inlet valves the water pressure on the inlet should be between 0 5 and 10 kg cm 7 and 145 psi If the pressure is too low the cycle time will increase considerably Incase of boiler fed machines a minimum ofhot water of 90 C should be available Forthe HF176 1251 HF234 1501 3 Water drain The machine is equipped with a drain valve with 3 outer diameter 80 mm This drain valve should be connected to the drain by means of the drain elbow which is delivered with the machine Cl The diameter of the main drain should be adapted to the water flow and the number of machines It should be sufficient to handle at least 160L min permachine CI It is necessary to connect the main drain at least on one side to an open air brake to allow ventilation 0 When the main drain has not been sufficiently deodorized every machine should be installed seperately with a deodorizer Main power connection NOZE XE N AO8E X Power of the breaker plugs Cl Remove the cover plate at the back of the machine See dimensions E CI Connect the power cable to the connectors 220V 3AC 220V 3 phase 3AC should be connected to the connectors
20. s program A coin value 0 or bigger than 1000 was programmed Example wrong price adjustment for program 5 E4 water level The appropriate water level was not reached after 15 minutes E5 Heating The wash bath did not reach the required temperature after 80 minutes of heating E6 door lock The door lock was released during the wash cycle E7 safety level The water was insufficiently drained the machine did not spin and the water is possibly still inside the tub E8 temperature sensor The temperature sensor is probably broken or malfunctioning 20 E9 motor protection The thermo magnetic protection was activated 5 times EA tilt The tilt switch was activated 15 times during final spin and the final spin was therefore skipped Eb tilt switch The tilt switch is blocked Mot 2 rotation sensor The speed detection is not operating properly The speed meter is probably out of order or disconnected r Remark When a malfunction occurs during a program the central display will communicate the appropriate error message at the end of the cycle When this malfunction has been removed and a new program has been selected this error message also disappears When malfunctions E6 E7 E9 or Eb are detected at the start of the wash cycle the program will not be started and the error mes
21. sage will remain on the display 21 l Maintenance of the machine General maintenance CI Clean the entire cabinet of the machine regularly and remove all traces of soap etc Remove all detergent residue in the soap dispenser with hot water Clean the door gasket and remove all detergents and other products Shut off the main water steam and power connections at the end of each day Do not change the setting of the water inlet taps on boiler fed machines once these have been installed It is recommended to leave the door and the soap dispenser open after use to ventilate the machine ON OOO Periodical maintenance _ The V belts ofthe motors shouldbe retightened after two to three months when first used This is necessary because these belts are subject to a one time stretching when first used By ignoring this instruction the belt starts to slip after a few months and will brake shortly afterwards Check regularly ifthe filters of the water inlet are not blocked by calcification aie Ifamachine frequently skips the final spin check whether the probe of the out of balance switch is still in the appropriate position that is horizontally centered and vertically 1 3 from the bottom inside the window When the drum is empty Cl An obstructed drain can cause frequent interruption of spinning for safety reasons Ly The automatic lubricator needs to be replaced each year Order number 212
22. the first 2 minutes after starting the program number is blinking and you can change the program in case of a possibly wrong selection To do so select another program with the SELECT button P This new program will start immediately Display information The left display will indicate the temperature of the wash bath in C or F on machines where this function has been selected The central display shows the remaining time to the end of the wash cycle For programs which are being run for the first time the machine will take a theoretical time estimate Ifthis time indication does not correspond to the real cycle time the cycle time will be corrected from the second cycle onwards Self Teaching function of the machine This correction will have to be preprogrammed and is not activated on program numbers higher than 20 The corrected time will also be lost when the power has been cut from the machine for more than 24 hours The right display will continue to show the selected program number Ifa Level stop was programmed which halts the programmer during the filling of the cylinder and or a Heat stop which stops the programmer during the heating up of the wash bath then the respective LED s light up in the display Once the required water level and or temperature have been reached the LED is turned off and the internal programmer advances again Wash cycle LED s Each program segment has a corresponding LED Each of
23. these 6 LED s light up when the appropriate segment is executed This way the program sequence can be accurately followed When a LED blinks the machine is taking up water When a LED blinks slowly the machine is heating up the water Spin LED s When the water is drained at the at the end ofa program segment and the machine spins ifso desired the eftspin L ED intermediate spin will light up together with thecycle LED Functioning of the spin LED s during intermediate spin LED drain distribution low spin coast Interm spin blinking rapidly continuously continuously Functioning of the spin LED s during gentle intermediate spin LED drain distribution low spin coast Interm spin blinking rapidly blinking slowly blinking slowly 11 Manual interventions during the program g SELECT gt START e s wO YR CONTROLLED 4 During final spin both the left spin LED intermediate spin will light up together with the right spin LED final spin Functioning of the spin LED s during final spin LED drain distribution low spin high spin coast tumble Interm spin blinking rapidly continuously slowly continuously off Final spin continuously continuously slowly continuously rapidly Functioning of the spin LED s during gentle final spin LED drain distribution low spin high spin coast tumble Interm
24. utton S ifatime stop is required in this phase of the program Ifno time stop is needed press the ECO button E to move on to the next segment of the program Run through the entire program in this way If needed return to previous segments by pressing the SELECT button P Errors can be corrected by returning to the erroneously programmed time stop in the segment and correcting by pressing the START button S After the final program segmentall programmed time stops will be displayed and the left display will show End Confirm this program by pressing the START button S again Now start the program Operation When a stop is reached during the run of the program the time will be stopped The wash bath will be filled to the appropriate level and temperature and the programmed wash action is executed The left display will alternately show temperature and StO while the central display is showing FI Now ifso desired additional detergents can be added When this has been done press the START button S to continue the run of the program To remove any possible remains of corrosive products in the tub the machine will rinse an additional 2 seconds Programmable automatic start By using this function a program can be started up to 99 hours later Programming After selecting the program press the SELECT button P again and keep it depressed Now push the START button S simultaneously and release same Onl
25. y now release the SELECT button P The left display now shows DEL Delay The central display shows 10 minutes Every push on the SELECT button P will add 10 minutes to the delayed start time Hours and minutes are separated by adecimal point 1 5 stands for 1 hour and 50 minutes After 10 the counting is done by hours By pressing the ECO button E the delay time can be counted down Operation After having set the desired delay time the count down can be started by pressing the START button S During the count down the displays blink and the remaining time is counted down In the last hour the displays blink faster When the delay time has elapsed the program is started automatically 16 Add g SELECT gt START gt O ze oz x a MICROPROCESSOR CONTROLLED 4 It is possible to run 2 programs automatically in sequence This can be handy to perform very special functions like waterproofing outerwear and add these to the wash program Linking 2 programs Programming First select the program which will be run last Now press the START button S and keep it depressed for at least 5 seconds The left display now shows Add Now select the program which will be run first The right display now shows both linked programs alternately the first to be run program during the longer time span alternating
Download Pdf Manuals
Related Search