Chief Manufacturing FSA-1004 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS Small Flat Panel Lift Arm FSA 1004 and KSA 1004 The Lift Arm FSA KSA 1004 is an accessory that can be used with a broad range of Small Flat Panel Displays The FSA KSA 1004 allows the user to move a display Lift Arm vertically up or down in a 13 inch radius The lift arm can be moved vertically 6 1 2 up from center and 6 1 2 down from center The FSA KSA 1004 is designed to safely hold a display weighing up to 25 lbs 11 3kg The display can be up to 30 inches wide The FSA KSA 1004 accommodates all VESA 75mm 100mm compliant displays BEFORE YOU BEGIN e CAUTION To prevent damage to the mount which could affect or void the Factory warranty thoroughly study all instructions and illustrations before you begin to install the mount brackets Pay particular atten tion to the Important Precautions on Page 2 e lf you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 or 952 582 6480 CHIEF MANUFACTURING INC 8832 000041 Rev F F CH l z F 1 800 582 6480 952 894 6280 FAX 952 894 6918 2007 Chief Manufacturing ICA 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com SAVAGE MINNESOTA 55378 USA 03 07 Installation Instructions FSA KSA 1004 A IMPORTANT WARNINGS and CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibi2. KSA 1004 CABLE MANAGEMENT Item Description Qty COVER Arm COVER Am Peram SCREW Phillips Flat Machine 8 32 x 3 8 WRENCH Hex 3 32 provided a Attach all cables to display b Open the cable management bracket by sliding it towards the edge of the arm NOTE f necessary cable management bracket attach screws may be loosened using hex key 30 Attach Screws OPEN Position CLOSED Position foh View from Bottom fofi A CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched when bracket is closed c Carefully insert cables into bracket Cable Management Bracket in open position Cable Path typical j NOTE Display not shown for clarity d Close cable management bracket by sliding it back towards the centerline of the arm NOTE If necessary cable management bracket attach screws may be tightened using hex key 30 A CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched by installation of cover 10 or screws 20 e Carefully insert cables in cavity located in lower portion of mount arm See Figure 22 f Using Phillips screwdriver install cover 10 with two screws 20 Cable Path typical NOTE Installation is complete
3. the following steps display NOTE Do not remove the four screws not shown that NOTE The two button head cap screws removed from attach the display to the interface bracket the mount will be replaced with longer screws 1 Disconnect the power audio video cables from the waen the ditan IS installed display not shown NOTE Keep the pivot pin removed in step 2 This part 2 Remove the cap screw washers pivot pin and will be used again when the lift arm is installed retaining nut from the display end of the mount Refer to Figure 2 Separate the display from the mount Display Mount Parts Typical PART NAME SCREW CAP WASHER FLAT Flat Washers SMALL WASHER NYLON LARGE WASHER NYLON NUT NYLOCK Pivot Pin Figure 2 Single Swing Arm FWS 110 Example Installation Instructions Installing the Lift Arm To install the lift arm perform the following procedures Installing base end of lift arm Locate the tension adjustment bolt on the lift arm see Figure 3 Install the pivot pin 40 and a washer 20 onto the base of the mount Assemble a button head cap screw 50 one stainless steel washer 70 washer 30 anda second stainless steel washer 70 onto button head cap screw 50 as shown in Figure 3 Insert the screw assembly step 2 into the pivot hole on the lift arm 10 and the base end of the mount Thread the lock nut 60 to the screw assembly step 2 at the bottom of the m
4. g the Display from the Mount 006 4 Installing the Lift Arm cccccccccccccsseseseseseseseseseseeeees 5 e 3 16 Hex Key wrench provided Installing base end of lift arm eee 5 Installing display end of lift arm eee eeeeeeeeees 5 NOTE Other tools may be required depending on the Adjusting Lateral Movement 6 method of installation Adjusting Lift Arm Tension cccscccseeeseeeeeeeeeees 6 Cable Management cccccccsececeeeseeeeseeeeseeeeaeees Error Installation Instructions PARTS Tension adjustment bolt 50 70 30 S ALF CS PH CT 40 i DON 20 J O ae 60 Figure 1 Lift Arm Installation Drawing PARTS LIST Table 1 Lift Arm Parts SPACER STAINLESS STEEL 320 x 018 LARGE LOCK NUT NYLOCK Ceo frocewm mmo oo eo FSA KSA 1004 Installation Instructions FSA KSA 1004 INSTALLATION Adding a lift arm modifies your mount configuration This 3 To remove the pivot pin see Figure 2 from the other procedure applies to most small flat panel displays end do the following particularly those with a pivot or swing arm whether wall mount or desk mount a If the mount is a pivot pitch wall mount remove the attaching hardware from the display Removing the Display from the Mount b If the mount is wall mounted desk mounted or has more than one swing arm remove the To remove the display from its mount perform the pee P attaching hardware from the arm closest to
5. lity of damage or destruction of equipment if you do not follow the corresponding instructions e WARNING Improper installation can result in serious personal injury Make sure that the mounting surface can support a redundant weight factor five times the total weight of the equipment if not reinforce the mounting surface structural members before installing the FSA KSA 1004 e WARNING Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted e WARNING The installer is responsible for verifying that the mounting surface to which the FSA KSA 1004 is anchored will safely support the combined load of all attached components or other equipment e WARNING The combined weight of the display placed on the FSA KSA 1004 must not exceed 25 Ibs 11 3kg the maximum load capacity of the mount e WARNING Watch for pinch points Do not put your fingers between movable parts e WARNING Make sure the mount is correctly oriented e WARNING When using an OFB and adding an additional arm to an existing mount the total number of arms on the mount cannot exceed two arms e CAUTION Check the unit for shipping damage before you begin the installation e CAUTION Over tightening mounting screws may damage your display CONTENTS TOOLS REQUIRED FOR Fata ar ae ce a a ta ea eleanigmnednenaeaa 3 INSTALLATION PAS LIS T oa A AEEA E 3 INSTALLATIO Niccoieei titei caress isteneit oksia 4 e 5 32 Hex key wrench provided Removin
6. ount CAUTION Over tightening a tension screw 50 will Cause excessive wear and may distort adjustment components 5 Using the 3 16 hex key provided tighten the button head cap screw 50 into the nut 60 several turns leaving flexibility in the hinged joint Do not over tighten the cap screw 50 50 Y 30 ie AB Original 50 C D l Pivot ij Pin ETS P K i GD CS 2 _ ED FSA KSA 1004 Installing display end of lift arm Install the original pivot pin see Figure 3 that was retained when the display was removed and a washer 20 onto the base of the mount Assemble a button head cap screw 50 one stainless steel washer 70 washer 30 and a second stainless steel washer 70 onto button head cap screw 50 as shown in Figure 3 Insert the screw assembly step 2 into the pivot hole on the lift arm 10 and the display end of the mount Thread the lock nut 80 to the screw assembly step 2 at the bottom of the mount CAUTION Over tightening a tension screw 50 will cause excessive wear and may distort adjustment components Using the 3 16 hex key provided tighten the button head cap screw 50 into the nut 80 several turns leaving flexibility in the hinged joint Do not over tighten the cap screw 50 Lift Arm Parts Co rawn a 20 moewa on 2 a0 emu wasnen non 2 Ca porns 1 MI ININJ gt B0 oa sonew suronneno 2 e0 rocknor mo 1 C70 spacer stanesss
7. rec 4 e0 umee Loon moek 1 BR Figure 3 Installing Lift Arm Installation Instructions Adjusting Lateral Movement CAUTION Over tightening tension bolt will cause excessive wear and may distort adjustment components To adjust the lateral movement tension perform the following procedures 1 Slightly tighten or loosen the tension adjustment bolt 2 Check for desired tension Repeat as necessary Adjusting Lift Arm Tension CAUTION Over tightening tension bolt will cause excessive wear and may distort adjustment components To adjust the tension of the lift arm 1 Raise or lower the lift arm until tension adjustment bolt appears in the opening 2 Using the 5 32 hex key provided adjust the tension adjustment bolt as follows NOTE There is no fixed number of revolutions to turn the tension adjustment bolt Tighten or loosen the bolt as needed When the bolt is adjusted correctly the display can be easily raised or lowered at any time and stay in place without sagging a To increase lift arm tension turn the tension adjustment bolt counterclockwise b To decrease lift arm tension turn the tension adjustment bolt clockwise 3 Raise or lower the lift arm to check for desired tension Repeat step 2 as needed FSA KSA 1004 Lateral Tension Adjustment Bolts Lift Arm Tension Adjustment Bolt Adjusting Lift Arm Tension Installation Instructions FSA
Download Pdf Manuals
Related Search