Chief Manufacturing CTA-2536 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS CTA 2536 Internal Dual Stud Wall Plate The CTA 2536 Dual Stud Wall Plate provides a mounting solution for the following wall arms e CTA 025 Single Stud Wall Arm 9 9 e WMA 300 Wall Mount Arm The CTA 2536 has a maximum weight capacity of a ng 150 Ibs 68 0 kg p ng ay D 9 o CTA 2536 Internal Dual Stud Wall Plate BEFORE YOU BEGIN e CAUTION To prevent damage to your equipment which could affect or void the Factory warranty thoroughly study all instructions and illustrations before you begin to install the CTA 2536 Pay particular attention to the Warnings and Cautions in this document e Ifyou have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 or 952 582 6480 TA CHIEF MANUFACTURING INC 8809 000028 Rev A 10 C H E E 1 800 582 6480 952 894 6280 FAX 952 894 6918 2004 Chief Manufacturing Ideas Supporting Ideas 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com SAVAGE MINNESOTA 55378 USA 11 04 Installation Instructions CTA 2536 Mnrortan WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Improper installation can result in serious personal injury Make sure that the mounting surface can suppor2. 4 REFERENCE ONLY Attaching Front Cover 1 Locate front cover and four M4 x 8mm Phillips head cap screws shipped with wall arm NOTES e The front cover may be partially removed and reinstalled to conceal power audio video cables after the TV Mount s installed e You may remove one or both knockouts on Figure 4 Install Cover on Wall Arm cover to assist routing to wall through cover 2 Install the front cover using four M4 8mm Phillips head cap screws See Figure 4 STEPS REFERENCE ONLY Connecting NPT Pipe or Nipple to Wall Arm 1 Locate M6 x 6mm set screw and 1 1 2 NPT pipe or nipple supplied with TV Mount or purchased separately 2 Connect the 1 1 2 NPT pipe or nipple supplied with TV Mount or purchased separately to the wall arm See Figure 5 3 Using the M3 Allen key install the M6 x 6mm set screw Tighten the set screw WARNING Make sure to tighten the M6 x 6mm set screw to prevent equipment damage or personal injury 4 Supplied with TV Mount or purchased separately Figure 5 Connect NPT Pipe or Nipple to Wall Arm
3. pencil awl or small nail to mark the mounting holes where the top two pilot holes will be drilled into the center of the wood studs Make sure that the mounting holes in the unit are level Using a 15 64 drill bit drill two pilot holes for anchoring the wall plate 10 See Figure 2 Using two 5 16 lag bolts 20 and two 5 16 flat washers 30 fasten the wall plate 10 to the wall See Figure 2 Repeat step 2 to drill four more pilot holes into the wood studs for the middle and bottom mounting holes Repeat step 3 to install the remaining four 5 16 lag bolts 20 and four 5 16 flat washers 30 into the wood studs and to secure the wall plate 10 Figure 2 Install the Wall Plate CTA 2536 Installation Instructions CTA 2536 STEP 3 WASHER M8 LOCK W ASHER Attaching Wall Arm to Wall Plate A M8 SCREW 1 Locate the wall arm six M8 flat washers 40 six M8 lock washers 50 and six M8 x 16mm button head screws 60 See Figure 3 CHIEF WALL ARM 2 Attach wall arm to wall plate 10 as follows a Using the parts 40 50 and 60 described in step 1 in the top mounting holes attach the wall arm to the wall plate 10 b Using the parts 40 50 and 60 described in step 1 in the bottom mounting holes attach the wall arm to the wall plate 10 c Using the M5 Allen key 70 tighten the six M8 x 16mm button head screws 60 to secure the wall arm to the wall plate 10 STEP
4. ssing any of the listed parts contact Customer Service at 1 800 582 6480 300 Table 1 Shipping Contents ITEM DESCRIPTION QTY 10 Wall Plate 20 5 16 X 2 5 Lag Bolt 30 5 16 Flat Washer 40 M8 Flat Washer 50 M8 Lock Washer 60 M8 X 16mm Button Head Cap Screw 70 M5 Allen Key ON AY OS TOOLS REQUIRED FOR INSTALLATION The tools required for installation are as follows Electric drill and bit set Stud sensor mechanical or electronic 1a box end wrench or ratchet with 12 socket 13mm box end wrench or ratchet with 13mm socket Level NOTE Other tools may be required depending on your method of installation Installation Instructions INSTRUCTIONS STEP 1 Determine a Suitable Mounting Location NOTE The wall plate 10 must be mounted to wood studs that are 16 apart on center See Figure 2 Locate the wall plate 10 six lag bolts 20 and six flat washers 30 WARNING It is the installer s responsibility to verify that the structure to which the mount is anchored will safely support five times the combined load of all attached components and equipment Determine a suitable mounting location Keep in mind that the wall plate 10 must be mounted to wood studs that are 16 apart on center Using a stud sensor locate the two wood studs where you will mount the wall plate 10 STEP 2 Installing the Wall Plate l Holding the wall plate 10 against the wall use a
5. t a redundant weight factor five times the total weight of the equipment if not reinforce the mounting surface structural members before installing the mount WARNING Be aware of the potential for personal injury or damage to the equipment if the CTA 2536 is not adequately mounted WARNING The installer is responsible for verifying that the mounting surface to which the CTA 2536 is anchored will safely support the combined load of all attached components or other equipment WARNING The combined weight of the TV monitor and all attached components and equipment placed on a Chief Wall Plate must not exceed 150 Ibs 68 0 kg the maximum support weight of the CTA 2536 WARNING Watch for pinch points Do not put your fingers between movable parts CAUTION Check the unit for shipping damage before you begin the installation PARTS 03 20 C O deseos HH TH IH H LH LE co VA No ALDO Noa Ct ch A Figure 1 CTA 2536 Parts Installation Instructions CONTENTS TOOLS REQUIRED FOR INSTALLATION INSTRUCTIONS colinas Determine a Suitable Mounting Location Installing the Wall Plate Attaching Wall Arm to Wall Plate Attaching Front COVE Connecting NPT Pipe or Nipple to Wall Arm CTA 2536 INSPECT THE UNIT BEFORE INSTALLING Unpack the carton Carefully inspect the parts for shipping damage Verify contents listed in Table 1 If you are mi
Download Pdf Manuals
Related Search