Chicago Electric 96996 User's Manual
Contents
1. 25249 5 et seq SKU 96996 For technical questions please call 1 800 444 3353 Page 3 Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure the parts listed on page 6 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Operation Refer to FIGURE 1 below and the Assembly Drawing on page 6 Warning Before attaching or removing the Drill Attachment unplug the drill not included from the power source If it is a cordless drill first remove the battery If a pneumatic drill disconnect it s air supply 1 Read and fully follow the manufacturer s safety and operating directions for the drill not included 2 Open the chuck on the drill not included and insert the Shaft 8 securely into the chuck Tighten the chuck securely 3 Thread the Handle 9 into the hole on either side of the Drill Attachment 4 To install a Drill Bit hold the Chuck Sleeve firmly in place and turn the Chuck counterclockwise Insert the shank of a bit not included all the way into the Chuck While holding the Chuck Sleeve in place turn the Chuck clockwise to2. metal wood and chemical dusts and mists 8 Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines 9 Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have them repaired by an authorized technician The handle must be kept clean dry and free from oil and grease at all times 10 Disconnect power Unplug tool when not in use 11 Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in SKU 96996 For technical questions please call 1 800 444 3353 Page 2 12 Avoid unintentional starting Be sure the switch on any power tool is in the Off position when not in use and before plugging in Do not carry any tool with your finger on the trigger whether it is plugged in or not 13 Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired 14 Take caution as some woods contain preservatives such as copper chromium arsenate CCA which can be toxic When cutting these materials extra care should be taken to avoid inhalation and minimize skin contact 15 Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform
3. CHICAGO Jale Power Tools RIGHT ANGLE DRILL ATTACHMENT WITH 3 8 KEYLESS CHUCK eye 1 96996 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product A Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 Specifications Max RPM 2 800 RPM 90 Degrees Chuck Capacity 1 16 3 8 Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equip
4. FIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 96996 For technical questions please call 1 800 444 3353 Page 5 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusi
5. its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn On and Off properly 16 Guard against electric shock Prevent body contact with grounded surfaces such as pipes radiators ranges and refrigerator enclosures 17 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools 18 Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool 19 Use proper size and type extension cord If an extension cord is required it must be of the proper size and type to supply the correct current to the tool without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool Longer extension cords require larger size wire If you are using the tool outdoors use an extension cord rated for outdoor use signified by WA on the jacket 20 Maintenance For your safety service and maintenance
6. lock the Drill Bit in place 5 Always use both hands while using this Attachment one hand on the Handle 9 and the other hand on the hand of the drill used with the Drill Attachment Operate the drill according to the manufacturer s instructions Be careful to avoid letting the bit get stuck as this will cause the Drill Attachment and drill to twist possibly causing injury 6 After operation unplug the drill not included from the power source If it is a cordless drill remove the battery Then turn the Chuck 2 counterclockwise to open the jaws of the Chuck and remove the bit Chuck FIGURE 1 Sleeve Chuck 2 Jaws of Chuck 2 Handle 9 Shaft 8 Maintenance Before each use clean off the Shaft 8 Make sure it has no dirt grease or debris clinging to it 2 Before each use open the jaws of the Chuck 2 following the instructions above and remove any dirt grease or debris Store it in a cool dry location out of reach of children i SKU 96996 For technical questions please call 1 800 444 3353 Page 4 Assembly Drawing Parts List 1 Chuck Screw MSxI6 a PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBU TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALI
7. ment Read all instructions before using this tool 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended 6 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair 7 Use eye and ear protection Always wear ANSI approved impact safety goggles Wear a full face shield if you are producing metal filings or wood chips Wear an ANSI approved dust mask or respirator when working around
8. on may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 96996 For technical questions please call 1 800 444 3353 Page 6
9. should be performed regularly by a qualified technician 21 Use tools with both hands when required Many tools such as chain saws drills routers etc require the use of both hands when operating This helps maintain tool stability and keeps hands away from the working area of the tool 22 Always adhere to all warnings and safety precautions provided with the drill that this Attachment is to be used with 23 Read and adhere to all safety warnings and instructions provided in the manual of the power drill being used with this Drill Attachment Note Performance of this tool may vary depending on variations in local line voltage or tool battery power Extension cord usage may also affect tool performance WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code
Download Pdf Manuals
Related Search