Chicago Electric 91332 User's Manual
Contents
1. Assembly Drawing 20 Charger Adapter not shown SKU 91332 Page 82. CHICAGO JEAN CORDLESS SCREWDRIVER SET 3 6 VOLT RECHARGEABLE ASSEMBLY AND OPERATING INSTRUCTIONS Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Battery Pack 3 6 VDC Ni Cd 600 mAh Charging Time 5 to 7 hours Charger Adapter Input 120 VAC 60 Hz Output 5 VDC 300 mA Speed 200 RPM Power Switch Reversing rocker switch Features Twist Handle for pistol or straight grip Accessories 8 Hex drive SAE sockets 5 Slot driver bits 4 Cross driver bits 4 Posidriv type ANSI Type IA drive bits 6 Hex drive SAE fractional bits 8 Star hexalobular internal drive bits 1 2 magnetic tip 1 1 hex adapter 1 1 L x hex adapter 1 Blowmold case Save This Manual You will need the manual for the safety warnings and precautions assembly in structions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry pl
3. ace for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be fol lowed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 2 5 Keep work area clean Cluttered areas invite injuries Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children Use the right tool for the job Do not attempt to force a small tool or SKU 91332 Page 2 10 11 12 13 15 16 17 attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear
4. damaged Never attempt to discharge a tool s battery by continuing to pull the tool trigger When tool performance begins to diminish stop the tool and recharge the battery for optimal performance 2 Insert the Charger Adapter module plug into the unit connector as shown below Plug the Charger Adapter module into an electrical outlet The red LED on the cordless Screwdriver will light Charge the new battery from 5 to 7 hours Battery usage time will ramp up as the new Battery is used and recharged Do not overcharge the battery Caution Never charge Battery for more than 7 hours continuously Charger Adapter should not be left plugged in or charging for more than 7 hours 3 Remove the Power Adapter from the electrical outlet and store in the Blowmold case SKU 91332 Page 5 Using the Cordless Screwdriver Straight Gri oY Be ON Grip Button Lock Pistol Grip Rocker Switch Chuck 1 Forward Reverse To change the screwdriver handle grip from straight to pistol grip slide the Grip Button Lock forward while at the same time twisting the handle counterclockwise See the two illustrations above Insert the desired bit driver or adapter into the Chuck 1 Engage the bit driver or adapter over the item being turned Press forward on the Rocker Switch for turning clockwise Press backward on the Rocker Switch for turning counterclockwise Maintenance When finished using the Screwdrive
5. ditions and situations that may oc cur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure the that all following parts are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual Accessory Bits and Adapters Cordless Screwdriver Charger Adapter SKU 91332 Page 4 Operation Battery Precautions 1 w o Do o A To avoid accidents only charge the supplied batteries Do not use a different charger adapter with this tool Do not expose the battery to rain or wet conditions To avoid damage of cable and plug never pull the cable to disconnect the charger Do not charge the battery if either the cable or plug are damaged Repairs should be carried out by a qualified technician only Do not touch the battery poles with any conductive source Do not store the battery in a box with other metal objects Do not throw the battery in a fire Charging the Battery The internal Battery does not come charged from the factory Charge before us ing 1 Note Never over discharge a battery by using the tool even after tool performance is decreasing Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can be permanently
6. not use the tool if any switch does not turn On and Off properly Guard against electric shock Prevent body contact with electrical circuits when using this tool Replacement parts and accessories When servicing use only identical SKU 91332 Page 3 18 19 20 replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Maintenance For your safety service and maintenance should be performed regularly by a qualified technician People with pacemakers should consult their physician s before using this product Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker In addition people with pacemakers should adhere to the following Avoid operating power tools alone Don t use a power tool with the power switch locked on Properly maintain and inspect all tools before use to avoid electrical shock Note Performance of this tool may vary depending on variations in battery power Warning The warnings cautions and instructions discussed in this instruc tion manual cannot cover all possible con
7. r place it in the Blowmold case along with all the accessories Store in a clean and dry location Recharge the batteries once a month whether used or not SKU 91332 Page 6 REV 07i Parts List Item Description 1 Chuck 2 Screw 3 Screw 4 Enclosure A 5 Screw 6 Enclosure right 7 Switch 8 Limit Block 9 Bearing 10 Limit Box 11 Enclosure B 12 Radiator 13 Gear 14 Steering Stem 15 Gear 16 Gear 17 Motor 18 Enclosure left 19 Battery 20 Charger Adapter NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALI FIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 91332 Page 7
8. restrictive hair covering to contain long hair Use eye and ear protection Always wear ANSI approved impact safety goggles Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have them repaired by an authorized technician The handles must be kept clean dry and free from oil and grease at all times Disconnect power Unplug Charger Adapter when not in use Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the tool or machine work surface before operating tool Avoid unintentional starting Be sure the switch is in the Off position when not in use and before plugging in Do not carry any tool with your finger on the trigger Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do
Download Pdf Manuals
Related Search