Channel Vision DP-XXXX User's Manual
Contents
1. wires as shown Align holes with mounting tabs Bend mounting tabs over to secure the Companion Board Connect Intercom Hub here see following pages for details Attaching the Camera DP XXXXC The DP 5xxxC and DP 6xxxC come with a mini camera that can be attached to the integrated mount that allows the camera to see through the opening in the plate The illustrations bellow show how to mount the camera Mini Pinhole Camera Threaded Mounting Hole Cone Lens Break away the section of perforated metal screen that covers the camera opening by pushing a screwdriver through the slot on the front of the door plate Press near the top or bottom of the section and the tabs that hold it in place will break free Attach the camera to the mount so that the cone of the camera points through the opening Adjust the camera to the desired position and secure it in place by tightening the screw in the mount Completed Sub assembly see Attaching the Companion Board Attach camera to mount using the screw provided AET Remove this section of screen material Attach pigtail to rear of amp lt Connect Intercom Hub here see following pages for details lt _ Connect to power supply and video distribution system 7 Channel Vision Compatible DP xxxx Channel Vision s DP Oxxx does not come with a camera but the DP 5xxx amp DP 6xxx Series door plates come with mini came2. the camera to the desired position and secure it in place by tightening the screw in the mount Completed Sub assembly see Attaching the Companion Board Attach camera to mount using the screw provided AET Remove this section of screen material lt _ Connect Telephone Entry Controller here see following pages for details amp Connect to power supply 5 and video distribution system Attaching the Companion Board DP XXXXC This door intercom product consists of two sub assemblies which must be attached to each other before the final assembly can be installed In this guide the electronic sub assembly will be referred to as the Companion Board and the mechanical assembly will be referred to as the Door Plate Review the following diagrams and assemble as shown Companion Board Connection Details Volume Adjustment U WEEHBEN O Oan O Microphone o attached to back side oO El To Speaker To Button o De Position the companion board onto the three mounting tabs as shown below The microphone attached to the back side of the companion board should line up with the microphone tube on the bracket Bend the mounting tabs to secure the companion board Connect the speaker and button wires by sliding the small connector over the exposed pins on the companion board as shown Microphone Companion Board Attach button and speaker
3. INSTRUCTIONS Telephone Entry Door Intercom B CHANNEL VISION 2007 CHANNEL VISION TECHNOLOGY Channel Vision s DP Series are 1 4 solid brass door plates that interface with a telephone entry controller to provide communication with the front door They are available in a variety of configurations including options for a hidden camera and compatibility with Panasonic s popular KSU phone systems Each plate comes with the DP 9001 or DP 9002 surface mount box depending on the finish color It is compatible with the DP Rbox ll flush mount box which is sold separately Features e 1 4 thick solid brass plate e Discrete speaker and microphone e Fits the DP Rbox Il flush mount box and the DP 9001 DP 9002 surface mount boxes e Available in 9 different finishes 4 h A 6 hee y DP Series Faceplate included oe 17 A 6 hae v LT y lt 4 h 4 gt DP 9001 or DP 9002 DP Rbox ll Surface Mount Box Flush Mount Box included optional Understanding the model number Part numbering DP door plates D P 02 1 2 A DP 0212C shown for example only Blank P 0920 P 0921 amp TE110 C 0920 compatible C P 0930 compatible P Panasonic compatible 212 White 222 Polished Brass 232 Antique Brass 242 Chrome 252 Oil Rubbed Bronze 262 Antique Copper 272 Satin Silver 282 Black 302 Satin Nickel 0 No camera 5 Black and white came
4. e original purchaser and a purchase receipt invoice or other proof of original purchase date will be required before warranty repairs are provided Mail in service can be obtained during the warranty period by calling 800 840 0288 toll free A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton This warranty gives you specific legal rights and you may have other rights which vary from state to state If a problem with this product develops during or after the warranty period please contact Channel Vision Technology your dealer or any factory authorized service center CHANNEL VISION www channelvision com 234 Fischer Avenue Costa Mesa California 92626 USA 714 424 6500 800 840 0288 gt 714 424 6510 fax email techsupport channelvision com 500 126 Rev B1
5. he door plate Place the microphone in the compartment and replace the plastic cap over the microphone Note that the plastic cap will form a friction fit over the top of the microphone wires holding them snug against the outer compartment wall until they exit at the base as shown Remove the mounting screws which are already attached to the bracket and use them to attach the companion board The companion board should mount on the front side of the bracket so that the screws pass through the companion board before threading into the bracket Companion Board Place pressure cap over microphone Attach button and speaker wires as shown with mounting screws Completed Sub assembly Connect Telephone Entry Controller here see following pages for details Attaching the Camera DP XXXX and DP XXXXP The DP 5xxx DP 5xxxP DP 6xxx and DP 6xxxP come with a mini camera that can be attached to the integrated mount that allows the camera to see through the opening in the plate The illustrations bellow show how to mount the camera Mini Pinhole Camera Threaded Mounting Hole Cone Lens Break away the section of perforated metal screen that covers the camera opening by pushing a screwdriver through the slot on the front of the door plate Press near the top or bottom of the section and the tabs that hold it in place will break free Attach the camera to the mount so that the cone of the camera points through the opening Adjust
6. late only 6 L x 4 W x D DP Series assembly 6 L x 4 W x 1 D Black amp White Camera DP 5xxx amp DP 5xxxP only Camera Lens 3 8mm Resolution 500 lines S N Ratio More than 48 dB Min Illumination 0 05 LUX F2 0 Power Supply 12VDC regulated Power Consumption 110 mA Video Output 1 Vp p 75 ohms Dimensions see instruction for the 5401 B W camera Operating Temp 10 C to 50 C 14 F to 122 F Color Camera DP 6xxx amp DP 6xxxP only Camera Lens 3 8mm Resolution 380 lines S N Ratio More than 48 dB Min Illumination 0 4 LUX F2 0 Power Supply 12VDC regulated Power Consumption 120 mA Video Output 1 Vp p 75 ohms Dimensions see instruction for the 6401 color camera Operating Temp 10 C to 50 C 14 F to 122 F Specifications subject to change without notice 11 S CHANNEL VISION 2 Year Limited Warranty Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts free of charge in the USA for two years from the date of original purchase This is ano hassle warranty with no mail in warranty card needed This warranty does not cover damages in shipment failures caused by other products not supplied by Channel Vision Technology or failures due to accident misuse abuse or alteration of the equipment This warranty is extended only to th
7. nic KXT30865 These 1 4 solid brass door plates provide an attractive alternative to the standard plastic door station sold by Panasonic This product interfaces with Panasonic s KSU phone systems to provide communication with the front door Model DP 6xxxP includes a color camera model DP 5xxxP includes a Black amp White camera and DP OxxxP includes no camera Connect to the In e terminals marked TO SYS From Telephone Service Provider Panasonic KSU System Phones N D 2 Conductor power Supply Extension not included Se Camera Power x BNC Video To Monitor or Connector Video Distribution TKS Coax Extension not included stallation Install a compatible mounting box at the desired location such as DP Rbox ll flush mount box DP 9001surface mount box or DP 9002 surface mount box Using a 2 conductor wire connect the door phone output of your Panasonic KSU to the empty screw terminal block on the DP see diagram Consult your Panasonic manual for instructions regarding door phone operation If necessary attach the camera s video output to a coax extension that is long enough to reach your monitor or video distribution equipment If necessary cut the connector off of the end of the power supply and splice in an extension using crimp on connectors Channel Vision CAT5 Intercom Compatible DP xxxxC The diagram below shows how to connect the DP xx
8. ra 6 Color camera Understanding the compatibility options There are three different types of systems that DP door plates can be used with The compatibility for these different types of systems is indicated by the suffix of the model number which follows the 4 digit numerical code If there is not a letter suffix on the model number such as DP 0212 that door plate is compatible with Channel Vision s telephone entry products including models P 0920 P 0921 C 0920 and TE110 If the suffix is the letter P such as DP 0212P then the door plate is compatible with Panasonic s phone systems which are designed to use the Panasonic door phone model KXT 30865 If the suffix is the letter C such as DP 0212C then the door plate is compatible with Channel Vision s Whole House CAT5 Intercom Hub model P 0930 Please double check to be sure that you have purchased the correct model number for your application Attaching the Companion Board DP XXXX and DP XXXXP This door intercom product consists of two sub assemblies which must be attached to each other before the final assembly can be installed In this guide the electronic sub assembly will be referred to as the Companion Board and the mechanical assembly will be referred to as the Door Plate Review the following diagrams and assemble as shown Companion Board Connection Details Remove the plastic cap that covers the microphone compartment on t
9. ras which attach to the integrated camera mount The DP 5xxx contains a Black amp White camera while the DP 6xxx contains a color camera The DP Oxxx DP 5xxx and DP 6xxx all interface with the Channel Vision s telephone entry controllers TE110 C 0920 P 0920 and P 0921 to provide audio and video communication with the front door From Telephone Service Provider Connect to the terminals marked TO SYS Intercom TELEPHONE ENTRY CONTROLLER CO Input Telephones House Telephones Q 2 Conductor Power Supply Extension not included xN Camera Power gt BNC Video To Monitor or Connector Video Distribution KS Coax Extension not included Installation e Install a compatible mounting box at the desired location such as DP Rbox Il flush mount box DP 9001 surface mount box or DP 9002 surface mount box e Using a 2 conductor wire connect the Telephone Entry Controller to the empty screw terminal block on the DP see diagram If necessary attach the camera s video output to a coax extension that is long enough to reach your monitor or video distribution equipment If necessary cut the connector off of the end of the power supply and splice in an extension using crimp on connectors Panasonic Compatible DP xxxxP Channel Vision s DP Panasonic Series models are a compatible replacement for the Panaso
10. xxC to Channel Vision s CAT5 Whole House Intercom system When the button is pressed on the DP xxxxC the ST 2000 Intercom Stations will generate a door chime Pressing Answer End will open communication with the DP xxxxC Model DP 6xxxC includes a color camera model DP 5xxxC includes a Black amp White camera and DP OxxxC includes no camera DP xxxxC These terminals can be ST 2000 used to connect a C5IDS Door Strike Relay Module Press here to answer door BNC Video P 0930 g Connector Page Tigger Power Page Out Coax Extension not included B To Monitor or 2 Conductor newer i Video Distribution Supply Extension not included Camera Power Installation e Install a compatible mounting box at the desired location such as DP Rbox ll flush mount box DP 9001 surface mount box or DP 9002 surface mount box e Using CAT5 wire connect the P 0930 to the 110 connector on the DP see diagram e If necessary attach the camera s video output to a coax extension that is long enough to reach your monitor or video distribution equipment e f necessary cut the connector off of the end of the power supply and 10 splice in an extension using crimp on connectors Specifications Speaker Size mm 50 Depth in 1 5 Impedance 8 Ohms Power Peak W 0 2 Frequency Range 500 Hz 4 5 kHz Dimensions DP Series p
Download Pdf Manuals
Related Search