Channel Plus 7400 B&W User's Manual
Contents
1. HANNELP us Model 7400 B amp W HIGH PERFORMANCE VIDEO CAMERA FEATURES e Low Profile Small Size Easy to Conceal Surface Mount Ideal for many different applications e Easy Installation Save valuable time Linear LLC 2055 Corte Del Nogal Carlsbad CA 92009 USA 760 438 7000 800 999 5225 fax 760 931 1340 www channelplus com 2004 Linear LLC Carlsbad CA USA INTRODUCTION WIRING The 7400 camera is available in White or Black The surface mount unit allows for The camera requires RG6 or RG59 coax cable to distribute the video signal to a discrete attractive CCTV camera installation monitor s or modulator s video input Use the power supply provided for proper operation No additional cable or wire is shipped with the 7400 Series cameras CAMERA COMPONENTS 1 The camera supplies video through the yellow female RCA connector If required use an RCA to F adapter not included to connect RG6 or RG59 video cable to the camera s video connector 2 The camera receives power from the power supply through a female mini jack Connect power to the camera using one of the following two options a If the power supply can be located near the camera connect the power supply s mini plug directly to the camera s mini jack b If the power supply cannot be located near the camera cut the power supply wire a few inches back from the power supply s mini plug Strip both ends of the wire and connect a length of 18 AWG 2 c2. Specifications Typical 25 C 5 C Image NTSC Color Image Sensor 1 3 Sony Superhad CCD Resolution 380 TV lines Minimum Illumination 0 5 lux Signal to Noise Ratio 45 dB AGC Yes Lens 3 6mm F2 0 Power 12VDC Power supply part 219704 Power consumption 1 5W Warranty Linear LLC warrants this product to be free from defects in material and workmanship for 5 years The time period will be measured using the date code labeled on the product Linear LLC is not responsible for damage to the product resulting from the buyer s improper handling stocking or warehousing of the product Any implied warranty arising from the sale of the product including implied warranties of merchantability and fitness for purpose are limited Linear LLC shall not be responsible for any losses damages or expenses whether direct consequential or incidental arising from the use or the inability to use the product Some states and countries do not allow limitations or how long an implied warranty lasts or the exclusion or limitation or incidental or consequential damages so the above exclusions may not apply The Linear LLC warranty gives specific legal rights in addition to other rights which may exist and vary from state to state and country to country The warranty is limited to repair or replacement of products returned freight prepaid to Linear LLC there is NO PROVISION FOR LABOR COST OR OTHER REIMBURSEMENTS OF ANY KIND 1 Failures due to product abu
3. onductor wire between the mini jack and the power supply s wire Solder the connections and insulate with electrical tape or use wire nuts x IMPORTANT OBSERVE PROPER POLARITY when extending the power ppwater CAMERA DOME INSTALLATION The surface mount hardware included with the camera allows easy installation in almost any situation including retro fit applications Provisions must be made for j f p physical wire connections but the camera assembly itself is simply screwed in wire Power supply wire polarity marking White Stripe place RCA CONNECTOR F CONNECTOR 1 Drill a 3 4 diameter hole in mounting surface to accommodate wiring 2 Mount the main bracket in the desired location using three 1 1 4 screws TO VIDEO MONITOR OR MALE RCA CHANNEL PLUS MODULATOR INPUT TO FEMALE TYPE F ADAPTOR NOT INCLUDED VIDEO OUT FROM CAMERA 12 VDC 300mA p x POWER SUPPLY 12 VDC WHITE POWER STRIPE TO CAMERA 7400 SERIES VIDEO CAMERA USE 1 1 4 SCREWS oH 3 Feed the camera leads through hole in mounting surface Connect wires see BLACK FEMALE MALE TO EXTEND POWER SUPPLY CONNECTION WIRING MINI JACK MINI PLUG USE 18 AWG 2 CONDUCTOR WIRE OBSERVE POLARITY 4 Place assembled camera housing into main bracket 5 Place dome over camera housing and attach to main bracket with three 1 2 screws Do not tighten completely ADJUSTMENT 1 After wiring make provisions to view the came
4. ra image 2 Adjust the camera to point it at the desired location Make sure image is level 3 With the camera properly aimed tighten the screws USE 1 2 SCREWS 2 TIGHTEN SCREWS
5. se such as negligence improper use and electrical surge including damage from lightning water damage or other damage due to natural disasters are not covered by the warranty The most common form of product abuse is surge damage caused by lightning 2 The warranty shall also be voided by any tampering with the date code labels or other markings on the product 3 Products that are damaged in transit to Linear LLC due to improper packaging or by the carrier shipping company will not be covered under the warranty If the product was damaged or lost by the carrier it is the sender s responsibility to create a claim against the carrier 4 The user is responsible for all labor costs associated with removing reinstalling and returning the product to Linear LLC Linear LLC at its option will repair or replace the defective product Replacements will be made from B Stock if an exact replacement is not available Linear LLC at its option will select the nearest equivalent product The user is responsible for freight charges to Linear LLC Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent service A customer may pay the additional costs for second day or next day service All products returned for warranty service require a Return Product Authorization Number RPA Contact Linear Technical Services at 1 800 999 5225 for an RPA and other important details Copyright 2004 Linear LLC 9900582 X1 C
Download Pdf Manuals
Related Search