Chamberlain TCR2 User's Manual
Contents
1. CHAMBERLAIN SPECIFICATIONS Output Rating 5 Amps 28Vac Vdc Max Power 12Vdc or 18 to 34Vac Vdc 30ma RF Frequency 300 or 310 MHz Accessory Transmitters TC1 TC2 and TC4 The TriCode digital receivers are designed for use with automatic garage gate operators and access control systems All TriCode products may be matched with Linear Delta 3 Multi Code and Stanley radio products which may already be installed The TriCode radio format provides a potential of 1024 different digital codes For Linear Delta 3 compatible products 256 different digital codes are available The codes are set using 10 position DIP switch system TRICODE TCR2 DUAL CHANNEL RECEIVER USED FOR TCR1 AND TCR2 To prevent possible SERIOUS INJURY or DEATH from electrocution e Be sure power is NOT connected BEFORE installing the receiver To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door e ALWAYS keep transmitters out of reach of children NEVER permit children to operate or play with remote control transmitters e Activate gate or door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel e ALWAYS keep gate or garage door in sight until completely closed NEVER permit anyone to cross path of moving gate or door NOTICE To comply with FCC and or Industry Canada IC rules adjustment or modifications of this receiver and or transmitter are prohibited e2. D system Figure 2 Delta 3 Linear 310 MHz Multi Code Stanley Configuration Switch 300 MHz 310 MHz Configuration Switch Delta 3 Linear Multi Code Stanley CST__MNT oy CST MNT g H DIP SWITCH SETTINGS amp POWER CONNECTIONS Setting DIP Switch The TriCode Receiver DIP switch CH1 is factory set OFF 1 10 and CH2 is factory set ON 1 10 Locate the 10 position DIP switch If this is a new installation using TriCode transmitters randomly set switches matching those of the transmitter Never use factory settings If receiver is used with Linear Delta 3 Multi Code or Stanley transmitters match the receiver DIP switch to the above transmitters Some transmitters may use toggle switches and it may be difficult to determine on amp off If so try reversing the setting on the TriCode DIP switch Figures 4 and 5 NOTE In LINEAR DELTA 3 mode 8 bits system the last 2 bits DIP 9 amp 10 settings are ignored They can be left in either ON or OFF settings Figure 4 Multi Stanley 1 Thru 10 Linear Delta 3 1 Thru 8 DIP Switch Channel 2 DIP Switch Figure 5 Channel 1 DIP Switch Power Supply and Relay out Connections There are six wires exiting the housing Figure 6
3. RED amp BLACK POWER INPUT BROWN amp BLUE CHANNEL 1 RELAY OUTPUT WHITE amp GREEN CHANNEL 2 RELAY OUTPUT Red Figure 6 Power Supply 12V 24V Black Q Brown Relay Output Chi O Blue ie White o Relay Output Ch2 O Green For installation and service information please call our toll free number 1 800 528 2806 or contact us through the web at www chamberlaingroup com 2007 The Chamberlain Group Inc 01 17468D All Rights Reserved
4. is required Remove back cover of receiver by removing screws Set jumper to the 12 volt setting Figure 1 JUMPER Mounting Holes P3 OUTPUT RELAYS amp CONFIGURATION SWITCH SETTINGS Setting Output Relay Mode The TriCode receiver is factory set for momentary relay output MNT e Momentary mode The output relay will be on for 5 seconds before turning off e Constant pressure mode Output relay is continuously on while receiving matching valid ID code from transmitter The output relay will turn off immediately once receiver does not receive a matching valid ID code from the transmitter Figure 3 NOTE If constant pressure mode is desired open front cover and move mode jumper from MNT to CST Figure 2 Figure 3 Relay CH1 mode CST MNT Relay CH2 mode CST MNT CH1 MODE Setting the Configuration Switch The TriCode receiver is factory set for Linear Delta 3 Locate the configuration switch and set it to the desired RF mode of operation Figures 2 and 3 Modes are as follows Linear Delta 3 works with all Linear Delta 3 transmitters transmitted at 310 MHz using 8 bits ID system Multi works with all Multi Code transmitters transmitted at 300 MHz using 10 bits ID system Stanley works with all Stanley radio transmitters transmitted at 310 MHz using 10 bits I
5. xcept for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Patent 6 915 146 POWER SWITCH SETTINGS NOTE To avoid the possibility of duplicating codes in adjacent systems all transmitters and receivers should be re coded prior to operation Unless using maximum number of codes the following four codes should not be used All DIP Switches ON All DIP Switches OFF DIP Switches alternating ON OFF DIP Switches alternating OFF ON Receivers should be installed at least 5 apart to avoid cross talk After completing installation operate transmitter outside of building to make certain the chosen DIP switch setting does not operate with nearby garage door operators and or security systems If so select another DIP switch setting and check the coded signal again Repeat as necessary RECEIVER MOUNTING Mount receiver to wall using 6 hardware not provided Hardware used will depend on mounting application Refer to Figure 1 for receiver mounting hole locations Figure 1 Back View Power Supply Selection Setting The TriCode receiver is factory set for 24 volt power input if 12 volt
Download Pdf Manuals
Related Search