Chamberlain PIR2300R User's Manual
Contents
1. top of the Base Station to wake it up If the green power is illuminated look at the two small white Base Station switches next to the Learn Button The 1 Dip Switch should be down towards the circuit board If it is up the Base Station has been muted If the Base Station signals when you press the Learn Button it is not muted PIR Motion Sensor is detecting motion only part of the time To detect cars it is best to mount PIR Motion Sensor at height of car s motor and have it between ten and twenty feet from the road Swivel sensor as needed The Alert is giving false alarms Check for moving tree branches or insects in sensor window PIR sensor can also be triggered by light shining directly in sensor window such as reflected sunlight or motion in front of a light source It is possible that condensation has built up on the sensor Wipe condensation from PIR Motion Sensor with cotton swab Let it sit inside for a few hours open to the air without the batteries and it should correct itself Check Sensor Switches on PIR Motion Sensor See Switch Settings Base Station beeps every ten minutes The battery in the Base Station is low Replace with 9 Volt battery or operate it using AC Adapter The Alert is not getting expected transmission range Keep both antennas vertical and keep PIR Motion Sensor antenna away from trees and metal objects Ensure Base Station is in clearest possible sight of the PIR Motion Sensor Th2. CHAMBERLAIN Overview The Wireless Pedestrian amp Vehicle Sensor is a Passive Infra Red sensor that detects movement of people and vehicles while allowing small animals to pass through undetected Each PIR Motion Sensor has its own unique ID for a secure radio link Base Station not provided can learn the signals of up to four PIR Motion Sensors The Base Station will give a single beep for the first Sensor that it learns a double beep for the second and so forth Additionally multiple Base Stations can work with the same PIR Motion Sensor to sound in different places Carton Inventory Sun Rain Shield Mounting Plate PIR Motion Sensor Assembly amp Test Step 1 Attach PIR Motion Sensor box to mounting plate with large silver screw Tighten screw until PIR Motion Sensor stays in place when repositioned Model PIR2300R Wireless Pedestrian amp Vehicle Sensor Step 2 000000 Install 4 AA Alkaline batteries not provided Lithium batteries recommended for colder environments LED light will flash Switch Settings Antenna PIR Sensor Switch 1 15 Detection Range 30 Detection Range Default Low Sensitivity ON High Sensitivity NOTE To avoid unwanted detection of small animals move Switch 2 to OFF Step 3 Insert battery pack facing away from circuit board and attach cover NOTE Ensure the batteries do not
3. e less objects between the devices the longer the range Base Station is not very loud An accessory such as a bell buzzer or light can be attached to the relay switch The relay switch can handle up to 120 AC volts at 10 amps The accessory device will need a separate power supply The accessories can be purchased at any electronics store NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment 114A3508B FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER 1 800 528 9131 www chamberlain DlY com NOTICE To comply with FCC and or Industry Canada rules IC adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2008 The Chamberlain Group Inc All Rights Reserved
4. touch the circuit board and the antenna and battery wires are not pinched Test PIR Motion Sensor by waving hand in front of sensor Test light should flash Secure cover with the smallest screws Programming PIR Motion Sensor to Base Station Step 5 A Ensure Base Station and PIR Motion Sensor are in close proximity to each other Press and release learn button on Base Station Buzzer will sound B Within 5 seconds wave hand in front of PIR Motion Sensor Test light will illuminate and Base Station will buzz PIR Motion Sensor Installation Mount PIR Motion Sensor horizontally on solid surface a few feet off the ground and within 900 of Base Station rotate sensor to access screw holes Unit should be able to swivel as needed Attach sun rain shield NOTE Keep PIR Motion Sensor antenna away from metal objects Do not mount PIR Motion Sensor in direct sunlight near moving tree branches or in the path of a sprinkler system Vehicle Alert Installation For cars the best mounting position is about 4 high between 10 20 back and angled to see the back of car after passing the sensor Troubleshooting The PIR Motion Sensor lights up but the Base Station does not respond The PIR Motion Sensor must be programmed to Base Station See Step 5 Ensure Base Station is on and is not muted If the green power light is not lit or is flashing press the Mute Button on the
Download Pdf Manuals
Related Search