Panasonic UT-101
Contents
1. Rear Tray Adjustment Screws a side ray adjustment Screws Tr mountings ic Power Supply mounting area Hardware Kit ee This Hardware Kit includes 1 Zip Ties 4 t Star Washer 5 1 4 20 Screws 5 2 3 4 5 Hold down lug Bumpers 4 D ie 2 1 i i Tall Hold Down Lugs 4 Hold down Lug Vinyl Cap 4 SW E7 gi i i L shaped Wrench 1 24 Keys 2 CON OU BPW N www havis com e 1 800 524 9900 Configuration 1 Ensure the UT 101 Universal Laptop Mount is unlatched by pulling the Latch Release Handle away from the unit 2 Before configuring your UT 101 to fit your laptop make sure you turn the computer s power off and remove any connected cords or peripherals 3 Place your laptop in the center of the Universal Laptop Mount Open your laptop screen and carefully close the Side Trays by pressing them inward a 4 Check to see that the Side Hold down Lugs fit over the laptop There should be a slight gap between the top of the Side Hold down Lugs and the laptop deck Configuration continued 5 If the Side Hold down Lugs installed by the factory are too short please follow Steps 5a and 5b Otherwise proceed to Step 6 5a Locate the adjustment screw for each of the four Side Hold down Lugs Remove the Lug by loosening the screw with the provided L shaped Wrench 5b Take the four Tall Side Hold down Lugs from the Packaging and install the Viny2. Owners Manual Havis Universal Laptop Mount VIS www havis com A 1 800 524 9900 Productivity in motion Before Beginning Original Instructions Havis is pleased to provide this Owner s Manual to aid in the proper installation and use of the UT 101 Universal Laptop Mount For questions regarding the set up of your UT 101 Universal Laptop Mount please contact Havis at 1 800 524 9900 or visit www havis com for additional product support and information This Owner s Manual applies to the following Part Numbers UT 101 e NEVER STOW OR MOUNT THE UT 101 DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE e DO NOT USE COMPUTER WHILE DRIVING e READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION Table of Contents SPECIICALIOMS ora agape sen ee ee ee ee 2 Parts CS Re een ee een 3 CONE UO at tee sr ests tec et een Sut eestor ee ed A PAS Ga ION een re ee E 9 Recon EIN nee ne 10 Specifications Universal Laptop Mount Dimensions 13 2 33 5 cm Wx 11 2 28 4 cm D x 2 2 5 5 cm H Weight 4 2 Ibs 1 9 kg Compatible Computer Dimensions Width 11 472 29 1 cm to 14 192 36 1 cm Depth 9 250 23 5 cm to 11 000 27 9 cm Height Short Lugs 0 665 1 7 cm to 1 265 3 2 cm Tall Lugs 1 265 3 2 cm to 1 865 4 7 cm HAVIS Parts Included Universal Laptop Mount Top Plate Te Fontres D side Hol down Lugs 7 re sidetys rr Reartay Bottom Plate
3. l Caps and Bumbers on each Lug Re install the Tall Side Hold down Lugs into the slots on the Universal Laptop Mount and tighten the screws Make sure the Lugs fit over the side of the laptop before continuing www havis com e 1 800 524 9900 ey Configuration continued NOTE Ensure the laptop is placed in the UT 101 Universal Laptop Mount and the Side Trays are fully closed before proceeding press Side Trays together until a click is heard 6 To adjust the Side and Rear Trays hold your laptop to the surface of the Universal Laptop Mount and carefully place the unit upside down on your lap Use caution when placing the laptop upside down Make sure that you do not damage the laptop screen 7 With the laptop completely forward and flush with the two Front Fences loosen the screws A approximately one full turn DO NOT REMOVE SCREWS With the laptop centered side to side in the Universal Laptop Mount slide both Side Trays at the same time inward until they touch the sides of the laptop Retighten the screws A Torque screws to 22 in Ibs 0 25 Nm 10 Configuration continued 8 With the laptop still completely forward and flush with the two Front Fences loosen the screws B approximately one full turn DO NOT REMOVE SCREWS Slide the Rear Tray inward until it touches the back of the laptop Retighten the screws B Torque screws to 22 in Ibs 0 25 Nm 10 9 To adjust the Side Hold down Lugs t
4. lign the four through holes in the Motion Device with the four 1 4 20 threaded mounting holes on the bottom of the Universal Laptop Mount Star Washers Hardware Kit item 2 1 4 20 Screws Hardware Kit item 3 Secure Universal Laptop Mount to the Motion Device using the appropriate hardware Torque screws to 72 in Ibs 0 8 Nm 10 NOTE If it is necessary to use mounting fasteners other than those provided inthe Hardware Kit make sure that once mounted the screw selected will protrude past the mounting surface into the Universal Laptop Mount by a minimum of 1 4 minimum amount ofthread engagement needed and a maximum of 1 2 maximum length allowed for acceptable clearance to interior moving components If it is necessary to strain relieve wires cables insert Integrated Zip Tie Push Pin Hardware Kit item 1 into any of the 1 4 holes on the Bottom of the Universal Laptop Mount Loop and tighten Zip Tie around wires cables as required www havis com e 1 800 524 9900 Reconfiguring Universal Laptop Mount If at any time you need to reconfigure your Universal Laptop Mount to secure a different computer use the following steps 1 Remove laptop computer and ensure the Universal Laptop Mount is latched by pushing in Side Trays until a click is heard 2 With access to the bottom of Universal Laptop Mount loosen the two Rear Tray Adjustment Screws A one full turn and pull tray outward Retighte
5. n screws by hand 3 Loosen the two Side Tray Adjustment Screws B one full turn and pull the trays outward Retighten screws by hand seers a Sn er 4 Return to Page 4 of this Owner s Manual and begin the Configuration set up instructions HAVIS Related Products Havis offers a wide variety of accessory products specifically for use with the UT 101 Universal Laptop Mount For more information or to order please visit www havis com DS DA 601 Rugged Communication Hub Rugged USB Ethernet hub makes adding peripherals to your mobile workspace easy and safe SS UT X Screen Stiffener Secure your laptop screen to prevent excess wear and reduce vibration while in use DS DA 102 USB Powered Keyboard Light Soft red LED light illuminates the laptop keyboard for night viewing CG X ChargeGuard Auto Shut off Timer Power management system that prevents dead batteries and protects mobile electronics from voltage anomalies www havis com 1 800 524 9900 Havis Inc 75 Jacksonville Road PO Box 2099 Warminster PA 18974 47801 Anchor Court Plymouth MI 48170 www havis com 1 800 524 9900 UT 101_OMN 7 12
6. urn the laptop on its side and loosen the screws and slide the Lug down so it makes firm contact with the laptop deck in order to hold the laptop securely in place Repeat this step for the remaining three Side Hold down Lugs Turn the entire unit right side up and test the Side Hold down Lugs to ensure that they are making contact with the laptop deck www havis com 1 800 524 9900 Configuration continued 10 If any of the Side Hold down Lugs or Front Rear Fences are covering ports loosen the Lug Fence screw and gently slide the Lug Fence along its slot until port is uncovered Retighten the screws to 22 in Ibs 0 25 Nm 10 o N m Deennnenet dssssidii i pa LE a LILLE LS eee eae NOTE It may not be possible to provide access to all ports on laptop For your safety it is important that all Lugs and Fences be rertained for securing the laptop in place 11 Make sure your laptop is secure on the Universal Laptop Mount prior to installation in a vehicle Ei Check List Laptop is in contact with the Front Fences 4 Side Hold down Lugs are set to proper height and are in contact with the deck of the laptop BZ Laptop is in contact with the Rear Fences lv No vital ports or switches are covered by the Side Hold down Lugs or Front Rear Fences where possible Installation 1 Tip the Motion Device up to allow access to the backside of the through holes 2 3 A
Download Pdf Manuals
Related Search