CDA FWV470 User's Manual
Contents
1. Firmly push the pushfit connectors B and F onto each end of the filter Clip the filter C into its bracket E noting the direction of flow through the filter C towards the ice maker Cut the flexible pipe A so it is slightly longer than the required lengths to and from the filter unit C When cutting the pipe use a sharp Stanley knife ensuring that the pipe is cut cleanly and square at all ends Firmly push the pipe A apx 12mm into the pushfit connector B Screw the large pushfit adaptor G onto the 3 way tee H Firmly push the pipe A apx 12mm into the pushfit connector F and push fit adaptor G 7 Connect the drain pipe as shown in fig 6 and the other end to an appropriate drain for example a laundry standpipe or under sink spigot Drain connections to the plumbing side are not supplied 8 Insert the appliance into the housing ensuring that the runners on the machine are located in the runners on the base unit Then slide the appliance fully into the housing Please note Due to the weight of this appliance the housing unit must be secured to the wall prior to installation You must ensure that all water connections are sound and check there are no leaks and check the drain is in place before completing installation For best performance the mains water pressure must be between 011 3 bar Do not use outdoors Do not locate the drain outdoors Do not insta2. normal use this fills with water this d water is used in the ice making process and is replaced every 24 hours by the automatic dr water from the water nozzle for drinking The water nozzle is height adjustable for ease of use To adjust the height hold the black oi and raise or lower it to the height required The nozzle will automatically remain at the hei To dispense ice When the ice drawer is full the display shows ICE FULL WATER READY Open the drawer fully and use the scoop provided to remove the ice as required Please note If the ice drawer is not emptied for a long period of time the appliance will go on standby and the display shows ICE OFF WATER READY After the standby period has ended the again If you do not want to wait for the standby period to finish press the ON button If the ice drawer is not emptied regularly an excessive accumulation of ice cubes could hin carriage You are recommended to open the ice drawer slowly after a long period of time ice cubes from the drawer Care and maintenance Always disconnect the appliance from the power before any cleaning or maintenance As the icemaker has a stainless steel or enamel surface you should use a nonabrasive clean will scratch the surface and could erase the control panel markings Stainless steel can be e dilute solution of water and mild detergent and drying to a shine with a clean cloth Proprietary stainless steel cleaners are available We reco
3. as been should contact CDA Customer Care for inspection repair or adjustment Installation min 2000m IMPORTANT THIS APPLIANCE SHOULD BE FITTED BY SUITABLY QUALIFIED PERSON We recommend that you seek the assistance of another individual when installing this appliance This appliance requires a mains water supply and a connection to the drain waste system drain connection is not supplied Slide the base unit into the housing ensuring the dimensions are correct as per figure 1 2 Fix the base unit in place by attaching the 10 screws in to the holes 3 Push the runners fully closed on the base unit 4 Connect the plug to the plug socket This must be accessible after the appliance has been installed 5 Using an appropriate supply pipe connect one end of the hose to the threaded inlet of the valve on the dispenser located at the rear of the appliance as shown in fig 3 and the other end to the mains supply tap outlet This must be accessible after the appliance has been installed 6 Install the inline filter Locate a convenient position to install the filter C remembering that it must be accessible when it is to be changed and functions best when mounted vertically Screw the filter bracket E to the cupboard wall using screws D if attaching the bracket to an interior wall use rawl plugs also Remove the dust caps from the ends of the filter C and write the installation date onto its label
4. coloured RED or BROWN If in doubt regarding the electrical connection of this appliance consult a qualified electrician supply cable the appliance may require removing for servicing N B Ensure that the plug socket is situated in an easily accessible place after install CDA To contact our Customer Care Department or for Service please contact us on the details below
5. e and pulling it t 2 Turn on the machine at the power switch on the left side of the machine The machine cycle which will take approximately five minutes During this process the display will s 3 Push the machine back into the housing 4 Switch on the machine by pressing the ON button 5 The machine is now ready for use and the display shows ICE ON WATER READY Please note You should clean the pipes through before first use to remove any impurities in the system place a jug under the water nozzle and press 9 for approximately two minutes disposing The Icemaker To make ice The icemaker will make ice automatically once it is switched on and will continue to make i full Whenever ice is removed the icemaker will make more ice until the compartment is f To dispense water The amount of water dispensed from the water nozzle is controlled by three different butt U water glass U water jug manual setting this button dispenses water as long as the button is pressed To change the preset buttons It is possible to adjust the amount of water dispensed by the preset buttons U e7 D To the water nozzle and press until the required amount has been dispensed Then confir U e x for the water glass button or buttons e for the water jug button Please note To stop water dispensing once a preset button has been pressed simply press the button a The ice water tray is located below the ice drawer In
6. habits CDA Manual for Installation Use and Maintenance Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect u product Please note that CDA reserve the right to invalidate the guarantee supplied with t installation or misuse of the appliance Under no circumstances should any external covers be removed for servicing or maintenan qualified personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cu fault with your appliance and to register your appliance for guarantee purposes CE Declarations of Conformity This appliance has been designed constructed and marketed in compliance with safety requi 2006 95 EEC Low voltage and requirements of EMC Directive 2004 108 EEC This appliance has been manufactured to the strictest standards and complies with all appl Electrical safety LVD and Electromagnetic interference compatibility EMC Parts intend food conform to EEC 89 109 4 IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACC DIRECTIVE 2002 96 EC At the end of its working life the product must not be disposed of as urban waste It must authority differentiated waste collection centre or to a dealer providing this service Disposing of a household appliance separately avoids possible negative consequences for t deriving from inappropriate disposal and enables the co
7. ll near a hob or oven To reduce the risk of electric shock do not mount over a sink CABLE TIE WATER DRAIN AK ADDITIONAL CABLE TIE TUBE WATER TUBE DOUBLE VALVE OUTPUT HOSE CONNECTION WATER TUBE Electrical information Warning This appliance must be earthed Green amp Yellow to Earth Brown to Live 13 Amp Fuse Cord Clamp The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug To chang follow the steps below 1 Remove the fuse cover and fuse 2 Fit replacement 13A fuse ASTA approved to BS 1362 type into the fuse cover 3 Replace fuse cover Important Do not use the appliance without the fuse cover in position How to connect an alternative plug If the fitted plug is not suitable for your socket outlet then it should be cut off and disposed o electric shock A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows e The wire which is coloured GREEN and YELLOW must be connected to the terminal whic or by the Earth symbol i or coloured GREEN and YELLOW e The wire which is coloured BLUE must be connected to the terminal which is marked with coloured BLACK e The wire which is coloured BROWN must be connected to the terminal which is marke
8. mmend the CDA E Cloth available stainless steel surfaces You should remove and clean regularly the ice compartment drawer and both sections of tl Once cleaning is complete reconnect the mains power supply If the appliance is not to be used for prolonged periods of time you should empty clean th electricity and water supply To empty the icemaker follow the steps below 1 Press the OFF button 2 Empty the ice drawer 3 Press the ON 9 and 7 buttons simultaneously 4 The display will show ICE OFF WATER EMPTY for approximately five minutes until IMPORTANT Steam cleaners must not be used when cleaning this appliance Ensure that all parts are correctly replaced after cleaning before attempting to use the ice You should replace the water filter every six months Replacement filters are available fro Troubleshooting WATER MISSING shows in the display Check the water supply is connected and switched on ICE FAULT WATER READY shows in the display Turn the icemaker off with OFF and the main switch on the side before at first switch on switching it on again The dispensed water has an unpleasant taste Ensure that only water pipes suitable for drinking water are used ICE FAULT shows in the display Turn the icemaker off with OF F remove some ice and turn it on again We recommend that the unit is not left on permanently IMPORTANT Do not operate with a damaged cord or plug after the appliance malfunctions or h
9. nstituent materials to be recovere in energy and resources As a reminder of the need to dispose of household appliances sep with a crossed out wheeled dustt Please note This appliance is designed solely to produce ice cubes and dispense water Other types of prove dangerous The CDA Group Ltd will not be held liable for any damage caused by inc the appliance e Read all instructions thoroughly before use e Before first use you must allow the icemaker to settle for at least twenty four hours pri e To protect against fire electrical shock and injury to persons do not immerse cord or pl e The use of accessory attachments not recommended by The CDA Group Ltd may resul e Ifthe appliance is switched off you should allow five minutes before switching it on ag damage to the compressor e You should only use cold drinking water in this appliance with water hardness level les icemaker ammm lt lt A Contr Panel Water Nozzle Ice Drawer Ice Water Tray Drip Tray On button Off button Water glass button this button dispenses a small amount of water Water jug button this button dispenses a large amount of water Manual water button this button dispenses water as long as the button is pressed By fm p p por Settings button this button changes the preset amounts of water The Icemaker Before first use 1 Pull the machine out of its housing by lifting the handle of the machin
Download Pdf Manuals
Related Search