Casablanca Fan Company Metropolitan User's Manual
Contents
1. CIRCUIT BREAKER TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON 18 70 84 CAUTION MOUNT WITH THE LOWEST MOVING PARTS AT LEAST 2 5 METRES ABOVE FLOOR OR GRADE LEVEL ATTENTION INSTALLER DE SORTE QUELES PIECES INFERIEURES SOIENT A AU MOINS 2 5 METRES AU DESSUS DU PLANCHER OU DU SOL P N 4843010 REV B MAROOPDG MOUNTING RECOMMENDATI ONS Before mounting your Casablanca fan read the following helpful recommendations The location of the fan air circulation and fan size are all important factors to consider before installation Location Ceiling fans have practical uses in almost every room in your home We suggest you follow these mount mg recommendations as you decide where to install your Casablanca fan For safety reasons the fan blades must be a minimum of 7 above the floor Do not locate the fan in a doorway or above a swinging door In any installation the tips of the blades must be at least 18 from the wall in order to provide sufficient clearance for the blades In bedrooms fans work best when mounted above the foot of the bed pool tables be sure to provide plenty of clearance to avoid damage from pool cues In low ceiling locations our optional Low Ceiling Adaptor LCA available at extra cost can be used to gain 3 2 In kitchens be sure to allow for open cupboard doors to clear the fan2. BLUE BLACK 3 way switch Connect this wire to the remaining rth STRIPE y 32 WITH black white striped wire on the W 32 control Se WHITE S pall cure this splice with a wire nut END 5 Remove the two remaining wires from the 3 way OF n switch Connect one of these wires to a black wire LINE LINE on the W 32 control Secure the splice with a wire BLACK rs e nut The remaining wire is to be connected to the WHITE BLACK BLACK other black wire on the W 32 Secure the splice STRIPE COMES Ses with a wire nut 6 Install the W 32 in the wall box with the two long screws provided 120V AC 7 Install the wall plate with the two short color BLACK matched screws provided 8 Installation of the second W 32 control is identi cal Repeat steps 1 through 7 NOTE If wall control operation is reversed fan switch controls lights and light switch controls fan turn off the power at the breaker or fuse panel then swap the two W 32 black white stripe wires Inteli Touch INTELI TOUCH OPERATION POWER The button is normally left in the on position Always turn the power off during cleaning or servicing the fan and during thunderstorms It is also used to exit or enter additional programs POWER must be left on to retain a previously set fan speed or light level INTELI TOUCH OPERATION SPEED CONTROL There are six individual speed settings for
3. lt METROPOLITAN gas CROSSBAR MOUNTI NG BRACKET INSTALLATI ON Proceed with installation as follows CEILING FAN Step 1 Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole Attach the bracket WIRING BOX with ground wire and ridges down to the Approved For Ceil ing Fan Installation ceiling fixture outlet box with the outlet box mounting hardware Tighten the screws firmly being careful not to bend the 2 i RIDGE bracket by over tightening CEILING SIDE WIRING DOWN CAUTION To reduce the risk of personal injury use only the mounting hardware provided with CROSSBAR the approved outlet box to install MOUNTI NG the crossbar mounting bracket BRACKET GREEN GROUND FLAT WASHER WIRE APPROVE OUTLET BOX HARDWARE TMM CANOPY SCREW 4 TA CANOPY A N CO CANOPY LOCK WASHER 4 HATCH ee CANOPY CANOPY INSTALLATI ON Step 2 Attach the canopy to the crossbar mount 4 ing bracket with three of the 8 32 x 2 1 4 long CROSSBAR MOUNTING gt Canopy screws and canopy lock washers Hand BRACKET INSTALLED gt tighten until snug against the ceiling Note On sloped ceilings align the canopy opening towards the top or room peak CANOPY LOCK WASHERS CANOPY SCREWS METROPOLITAN lt Step 3 To hang the fan body in the canopy hold the fan body firmly and in sert the nyl
4. wire connections HI Remove the two wires from the switch rn WIN 2 GREENS 4 5 Connect the two wires just removed from the switch to mie the W 32 wall control black wire and black white stripe Bre wire Secure these connections with wire nuts NECESSARY 6 Install the W 32 in the wall box with the two long screws SEE NOTE provided 7 Install the wall plate with the two color matched screws NOTE If wall control operation is reversed fan switch controls lights and light switch controls fan turn off the power at the breaker BLACK BLACK WITH WHITE STRIPE 120V AC BLACK INTELI TOUCH DUAL W 32 INSTALLATI ON CAUTION Ensure power is turned OFF at the breaker BLACK FROM LIGHTS FROM LIGHTS or fuse panel then swap the two W 32 black white stripe wires or fuse panel before starting installation se n To control the fan and lights from two locations a NEUTRAL SEE MOTE BELOW three way circuit use 2 W 32 wall controls 1 Remove the screws and switch plate from the ex isting switch box and the screws holding the switch in the switch box F 2 Pull the existing switch from the switch box to GRounp expose the wire connections 3 Determine which wire is connected to the common terminal of the 3 way switch The terminal will be marked on switch 4 Remove the wire from the common terminal of the
5. Erantz This slope is 32 This is the maximum slope that will allow the fan to hang straight down It is OK to install your fan Calculation of 32 dints This slope ts more than 32 Use the tear off Ceiling Angle Template card inserted in the a Your fan will not hang straight down an adaptor is necessary Contact your local Authorized Casablanca Dealer in regards back of this manual it provides you with a simple go or to purchasing a Slope Ceiling Adaptor no go for installing your fan on a sloped ceiling INSTALLATION INSTRUCTIONS Unpacking Before assembling and installing your ceiling fan remove all parts from the shipping cartons and check them against the parts listed here Before discarding packaging material be certain that all parts have been removed PERMA LOCK HARDWARE ALLEN SET SCREW Yq 20 Ya PRE INSTALLED 3mm ALLEN WRENCH DOWNROD amp BALL ASSEMBLY FAN PREPARATION IMPORTANT SAFETY INFORMATI ON BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY Prepare for fan installation as follows Step A Route the wires from the motor through the PermaeLock downrod and ball assembly Tip The downrod has a tapered thread that is designed to lock completely when correctly installed Step B Using the provided allen wrench loosen the set screw several turns
6. ure as it is battery operated Once power is restored to the fan it will receive an auto update signal from the remote control within 30 minutes after power is restored All previ ously set modes and functions will be restored to the fan Button Operation Rapid button pressing causes erratic fan operation For reliable operation of the remote control and fan you must wait ONE SECOND between button presses to allow the radio signal to be transmitted to the fan and received Labeling If you have more than one Comfort Touch fan in your home we suggest you put an adhesive room 3 identification label on the back of Ww NS the control Labels are in the remote control package SPACE FOR LABEL General Your Comfort Touch remote control uses one of 15 different ra dio signals to control the fan This channel is set at the factory There may be times when the channel needs to be changed i e Two fans in the house set to the same causing interference Two fans are to be operated from one control Two controls are to operate the same fan see special Dual Remote Control section on the next page COMFORT TOUCH TEST PROGRAM Press the button to activate a two minute program that puts the fan through a complete functional test The test starts with a full screen display then the preset chan nel number before going into a full light fan and reverse exercise Follow the remote con
7. To enter the Safe Exit Program 1 Turn the off for at least three seconds 2 Turn the on gt La 3 Immediately operate the buttons in the following sequence FAN D e FAN 4 LIGHT D tg LIGHT _ After you hear the confirming audio 5 X P dg tones from the fan immediately press 4 The lights will blink to indicate this command has been accepted Note Both Light Minder and Safe Exit The lights will stay on for twenty seconds and then begin to dim After a programs can run at the same time total of thirty seconds has elapsed the lights will be off completely To however the dimmer cannot be used cancel the Safe Exit Program turn the off for three seconds the light may only be turned ON OFF INTELI TOUCH OPERATION HOME SAFE PROGRAM The Home Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times J To enter the Home Safe Program 1 Turn the off for at least three seconds 2 Turn the on 3 Immediately operate the buttons in the following sequence ciem CEN Clem Goran 4 A tone and flashing light indicate this command has been accepted This program overrides all manual control of lights and fan The lights will now be automatically cycled on and off in a controlled sequence as follows On 1 hour off 1 2 hour on 2 hours off 1 hour 1 2 hour then off 2 hours This seven hour pattern will repeat continu
8. each 1 5 F increase or decrease in temperature If temperature decreases enough to turn the fan OFF the Auto Speed indicator will flash slowly to remind you that the fan will turn on when the temperature increases 55 mmm secvam REVERSE 4 SAVER TEST WINTER Note The temperature displayed is from an electronic thermometer built into the remote control that reads room temperature It is not AUTO SPEED a thermostat that controls the room temperature l Temperature Accuracy 3 F To cancel Auto Speed simply push the button again Selecting also cancels Auto Speed COMFORT TOUCH SAVER FEATURE The Saver mode will automatically turn lights off 1 hour after the lights are turned on Press the button and SAVER will appear in the display An audio tone will warn you 20 seconds before the pro gram is going to turn the lights off Press the button again to Pa SAVER AUTO SECURITY REVERSE WINTER lace batteries when Lo is displayed AUTO SPEED Thermostatic fan speed control SECURITY Lights ON and OFF automatically REVERSE Change airflow up or down SAVER Lights turn OFF after 1 hour TEST Tests all fan and light functions WINTER Draft free heat recirculation COMFORT TOUCH WINTER FEATURE cancel The Winter mode provides draft free recirculation
9. fan to its original settings press any button Fan will reset itself within about 30 minutes after power is restored when remote sends normal update message to fan WHEN AC POWER IS TURNED ON LIGHT COMES ON OR FAN TURNS Remote control defective remote buttons pressed too soon AC electricity irregularities noise spikes fluctuations or failure Turn off with remote and restart replace remote control unit or wait twenty seconds for electronics warm up check AC electricity for irregularities defective light dimmers noise spikes voltage changes caused by appliances motors supply brown outs or interruptions or storms etc 761 Corporate CENTER DRIVE Pomona 91768 Free 888 CASA 1ST 227 2178 www CasablancaFanCo com CoPyYRIGHT 2000 CasasLanca Fan Company U S PATENT PENDING PRINTED INROC
10. or Winter use Saver or run the Test mode without affecting Security mode SECURITY MODE CYCLE 1 On for 30 minutes 80 bright 5 On for 60 minutes 100 bright 2 Off for 30 minutes 6 Off for 120 minutes 3 On for 120 minutes 50 bright 7 On for 15 minutes 20 bright 4 Off for 60 minutes 8 Off for 60 minutes You may still turn the light ON and OFF or OFF and ON manu ally for temporary lighting but the light will continue to operate automatically at its programmed times Changing the control channel 1 Hold the Ct button down until a tone is heard 2 The temperature display will show the current channel number 3 Press fan up or down buttons to change the number to a REMOTE ii unique number from 49 to 63 CONTROL DO NOT use other channel numbers CHANNEL 4 Push ms to return to normal operation NUMBER You will need to repeat this step any time you remove the remote Note Always change the remote control channel control batteries Record the new channel setting in the space pro first The fan channel can only be changed by vided on the rear label having the desired channel already set in the re mote control COMFORT TOUCH CHANGING CHANNELS FAN 1 Turn OFF power to the fan for five seconds or longer using the wall switch or circuit breaker 2 Turn the power back ON WAIT 20 SECONDS You have 90 seconds in which to compl
11. to allow installation of the downrod Thread the downrod into the motor coupling until it stops turning this will take at least four and a half full turns Step Securely tighten the set screw with the provided allen wrench to ensure safe operation of your fan CAUTION Failure to fully lock in the down rod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation 9 MOTOR WIRES GROUND WIRE DOWNROD amp BALL ASSEMBLY TAPERED THREAD ALLEN SET SCREW MOTOR COUPLING CROSSBAR WIRE NUT 4 MOUNTING BRACKET ADDITIONAL HARDWARE A I CROSSBAR MOUNTI NG BRACKET SCREW 27 4 2 Co CROSSBAR MOUNTING BRACKET SCREW 172 FLAT WASHER 2 GETTING STARTED CONTINUED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan an approved ceiling fixture outlet box must be installed and wired Warning To reduce the risk of fire electrical shock or personal injury mount to outlet box marked acceptable for ceiling fan support Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source either circuit breaker or fuse box lower the old fixture and disconnect the wiring Check the ceiling fixture outlet box to be sure that it is marked Approved for ceiling fan mounting If it is not a new box must be installed
12. CKET ALKALI NE BATTERY 3 WALL BRACKET ANCHOR 4 x WALL BRACKET SCREW 4 COMFORT TOUCH W 21 WALL BRACKET INSTALLATION Installation of Remote Control The wall mounting bracket for the remote control should be located in a position that is approximately eye level Secure the wall mounting bracket with the 11 4 screws or anchors provided making sure it is level with the floor CAUTION DO NOT MOUNT REMOTE CONTROL ON OR NEAR A METAL SURFACE ERRATIC OPERATION WILL OCCUR Changes or modifications not expressly approved in writ ing by Casablanca Fan Co may void the user s authority to operate this equipment This device complies with RSS 210 of Industry Canada Operation is subject ot the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device AUTO 17 sEcURIT SAVER 2 6 3 gilig SPEED TEST WINTER O Mount control in convenient location WALL Remove for handheld or tabletop use COMFORT TOUCH W 21 BATTERY INSTALLATION MOUNTI NG BRACKET Battery Installation Install three AAA alkaline batteries in the sequence shown and replace the battery compartment cover then press the remote control firmly to the wall bracket so that the Velcro pads grip the pads on the rear of the control The remote
13. METROPOLITAN OWNER S MANUAL INTRODUCTION MOUNTING RECOMMENDATIONS FAN INSTALLATION CONTROL FEATURES INTELI TOUCH OPERATION TROUBLESHOOTING INTELI TOUCH COMFORT TOUCH OPERATION TROUBLESHOOTING COMFORT TOUCH CONTENTS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation therefore before attempting to install and operate your Casablanca fan read this owner s manual completely and carefully Retain this manual for future reference CAUTION To avoid possible electrical shock make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure All wiring must be in accordance with the National Electric Code ANSI NFPA 70 1993 and the appropriate local electrical codes The National Electric Code requires proper grounding as a precaution against electrical shock A qualified electri cian should be consulted if you are unsure This fan is designed to be installed on an existing electrical outlet box The outlet box must be UL Listed for ceiling fan installations if it is not a new box must be installed Casablanca extension poles are available for sloped or high ceiling installations This ceiling fan requires a grounded electrical supply of 120 VAC 60 Hz and a minimum 15 amp circuit The maximum current requirement for the fan with light fixture is 3 8 amps The fa
14. TOR COMFORT TOUCH ADDITIONAL CONTROL FEATURES Additional control program features are available from the con trol panel by opening the control panel door To activate a control function press the appropriate button the display will indicate that the program is running In some cases you can run more than one program at once such as and sw and the display will indicate that they are both activated In other cases one program will override another as the two programs can not run together i e Full details explained the sections that follow CONTROL PANEL DOOR secu Ga Ca REVERSE inter CONTROL PANEL COMFORT Touch COMFORT TOUCH REVERSE FEATURE Pressing the button will change the direction of rotation An audio tone signals the beginning of the reverse sequence and you will see the airflow direction arrow changing The fan gradually slows to a stop then reverses direction Note This function does not operate if the fan is not running REVERSE COMFORT TOUCH AUTO SPEED FEATURE In the Auto Speed mode fan speed changes in response to changes in room tempera ture Push the button to start words AUTO SPEED show on the display Set the fan speed to the speed at which you are most comfortable Once set the fan will increase or decrease by one speed for
15. blades Do not install a fan close to or over a pool or spa High humidity combined with corrosive gases will destroy the finish and warp the blades Fan Size Variable fan speed capability permits the use of a full size 52 fan even in smaller rooms For very large rooms two fans may be needed SLOPED CEILING INSTALLATIONS MAXIMUM HANG TRU 9 ANGLE 322 Suggested Extension Pole Lengths Ceiling Height Pole Length 8 Standard 8 6 9 9 6 10 11 12 13 14 BLADES MUST BE A MINIMUM OF 7 ABOVE THE FLOOR When to Use Extension Poles 7 MINIMUM For best performance and best appearance an extension pole should be used with your Casablanca fan when installing on 2 high cathedral ceilings or sloped ceil ings Casablanca offers standard poles in increments of 6 up to 5 Custom poles are available in lengths up to 10 See your Authorized Casablanca Dealer for details TT Note Fan may wobble or vibrate if pole length is not long enough and inside blade istoo close to downslope EXAMPLE 1 or side wall Extending pole length This slope is less than 32 will usually solve problem It is OK to install your fan EXAMPLE 2
16. can remove heavier dust Surface smudges or accu mulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth An antistatic agent may be used but never use abrasive cleaning agents These will damage the finish Painted and high gloss blades may be cleaned in the same manner Blades Wood finish blades should be cleaned with a furniture pol ishing cloth Occasionally a light coat of furniture polish may be applied for added protection and beauty Never Lubricate this Fan The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life Do not attempt to oil the motor Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs Replace bulbs with same type as removed from the fixture Each fan is rated for a maximum TOTAL wattage of lighting Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty PROBLEM POSSIBLE REMEDIES NO FAN OR LIGHT Check main circuit fuses curcuit breakers or wall switch position Check all wire connections making sure the power is turned off during this inspection FAN WOBBLES OR SHAKES EXCESSIVELY Be sure canopy pin is properly set into the slot on the ball Check the screws holding the blade holders to the fan motor Tighten as necessary Check the angle of the blades to
17. control can be easily removed at any time should you wish to use it in another location J ust give the control a gentle tug to remove it REMEMBER THE REMOTE CONTROL WILL GO BACK TO THE ORIGINAL FACTORY PRESET CHANNEL NUMBER WHEN THE BATTERIES ARE CHANGED CHANGE CONTROL CHANNEL IF NECESSARY AFTER BATTERY REPLACEMENT PRESET CHANNEL Rear View of Remote Control N Ke B ttery a gt Battery G Menea 2 OPEN USE ALKALINE BATTERIES ONLY COMFORT TOUCH W 21 LOW BATTERY WARNING Low Battery Indicator The remote control warns of a low battery condition by displaying a rapidly flashing Lo in place of the temperature display When this occurs replace with fresh alkaline battery WARNING Use of batteries other than non leak sealed alkaline in the remote control will void the warranty and can destroy the unit Note When the remote is in the low battery mode the fan may not respond to control commands correctly even though the fan may be running S SPACE t FOR ROOM LABEL Turning On Your Fan The fan will not receive any signals for the first 20 sec onds after power on This allows the electronics to warm up and stabilize Power Failure The remote control is not affected by household power fail
18. e fan will now respond to either of the remotes when pressed Reminder These steps will have to be repeated whenever the batteries are changed When AUTO SPEED SECURITY SAVER or TEST modes in ef fect at any control Automatic control will only be from the control that was last operated manually TWO CONTROLS OPERATI NG ONE FAN When two controls are used for the same fan we suggest that both controls be set for the same features AUTO SPEED SAVER etc so that performance remains the same as you move from one to the other Remember the fan will only respond to updates from the control that was last operated manually seo reverse BASE To confirm that the control is the BASE 1 Press for 3 seconds until a beep is H AUXILIARY DISPLAY SECURTY REVERSE COMFORT T OUCH TROUBLESHOOTING Before Requesting Service Please follow this troubleshooting guide before contacting your dealer for assistance Caring for Finishes For cleaning a soft brush or lint free cloth Never Lubricate this Fan should be used to prevent scratching the finish A vacuum cleaner The precision motor at the heart of your Casablanca fan features brush nozzle can remove heavier dust Surface smudges or an accu sealed bearings that are lubricated for life Do not attempt to oil mulation of dirt and dust can easily be removed by using a mild the motor detergent and sli
19. ete step 3 3 Press and hold the st and buttons together until the display shows for Change Channel then release The control automatically changes the fan channel to the new setting A second remote control can be purchased from your dealer to provide dual remote control of one fan Because the fan could be confused by two controllers signaling different information it is necessary to set a BASE control and an AUXILIARY control The last control manually operated controls the fan Where two remote controls are used to control a single fan they must be set so that saver b DISPLAY BOTH controls are set to the SAME channel BASE Check ONE control is made into the BASE control OTHER control is made an AUXILIARY control All remote controls leave the factory as a BASE heard si Initial remote control settings 2 Confirm temperature display shows b 1 Set both the controls to operate the fan 3 Press Caw again to set 2 Select one of the remote controls to be the BASE unit COMFORT TOUCH DUAL REMOTE CONTROL AUXILIARY Change the other remote to be used in the room to AUXILIARY 1 Press until a beep is heard Remote displays b 2 Press up or down buttons to change the display to 3 Press Cao again to set Th
20. ghtly dampened soft cloth An antistatic agent Changing Light Bulbs may be used but never use abrasive cleaning agents These will Be sure to turn power to the fan OFF at the wall switch or circuit damage the finish Painted and high gloss blades may be cleaned breaker before changing light bulbs Replace bulbs with same type in the same manner as removed from the fixture Each fan is rated for a maximum TOTAL Blades Wood finish blades should be cleaned with a furniture pol wattage of lighting ishing cloth Occasionally a light coat of furniture polish may be Exceeding the rated maximum allowable wattage for the fan will applied for added protection and beauty burn out the fan electronics module and void the warranty FAN O K NO LIGHT Check for burned out light bulb Check fan light wires REMOTE CONTROL OF FAN IS ERRATIC Check batteries installed correctly Install fresh ALKALINE batteries SELECTING WINTER MODE CANCELS AUTO SPEED Normal CHANGING SPEED OR DIRECTION CANCELS WINTER Normal FAN APPEARS TO RESPOND TO UNKNOWN SIGNAL Change channel of control and fan to a number between 49 and 63 CONTROL ALSO OPERATES A SECOND FAN IN HOME Change channel on control and fan TEMPERATURE DISPLAY DOES NOT CHANGE QUICKLY Normal Updates only every 2 minutes FAN WOBBLES OR SHAKES EXCESSIVELY Make sure hanging ball slot is properly aligned Tighten canopy and mounting crossbar screws Tighten all blade screws Blades must be balanced con
21. make sure that a blade holder has not been bent during installation FAN NOISY DURING OPERATION Check and tighten light fixture retaining screws glass shade screws and or the light bulb s Tighten canopy screws and mounting plate assembly Tighten the blade to bladeholder screws and blade holders to flywheel Make sure all screws in the motor housing are snug but not overly tight Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have fallen off the wire splices Tighten or adjust as necessary BREAK IN PERIOD DOES NOT RUN ON LOW SPEED Let fan run at high speed for two 2 hours If new break in may be required run at higher speed for several days LIGHTS FLASH OR BLINK DURING OPERATION OF W 32 WALL CONTROLS FAN MAY ROTATE OR MAKE AUDIBLE TONES DURING OPERATION OF THE W 11 AND W 12 WALL CONTROLS Normal operation WHEN AC POWER 15 TURNED ON FOR THE FIRST TIME THE LIGHTS OPERATE NORMALLY BUT W 32 WALL CONTROL OPERATION 15 REVERSED FAN BUTTON OPERATES THE LIGHTS LIGHT BUTTON OPERATES THE FAN Reverse the 2 black and white striped wire connections FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES CHANGING SPEED OR INTENSI TY WALL CONTROL OPERATI ON 15 INTER MITTENT Check AC supply for irregularities noise spikes fluctuations or failure or circuit board assembly O O O 2 REMOTE CONTROL REMOTE CONTROL W 21 WALL BRA
22. n uses about 1 amp or 100 watts Maximum light current is 2 8 amps or 340 watts of lighting Where wire nuts are employed be sure all bare wires are within the connectors When installing the canopy hatch make sure all wires are within the canopy and that no wires are being pinched For best performance and for your warranty to be valid use only genuine Casablanca blades light fixtures and accessories The blades in each pack are matched for equal weight to assure smooth fan operation 11 more than one fan is being installed be careful not to mix blades from different cartons Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer It is always good idea to have an assistant to help with the installation When cleaning painting or working near your fan be very careful of the fan and blades Always turn the power OFF to the ceiling fan before servicing it working on it or replacing light bulbs Never insert anything into the path of the fan blades while the fan is in operation Never install a fan over a pool or spa Never operate a fan that has been damaged in any way Contact Casablanca Fan Company by calling toll free 1 888 227 2178 or contact your local authorized Casablanca dealer for assistance in obtaining service FUSE BOX REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON L
23. nce holes in the mounting plate Carefully slide the switch housing into the mount so that the threaded holes are directly behind the clear ance holes Step 12 Install the three screws removed in Step 10 Tighten securely by hand only PROCEED TO YOUR FAN S CONTROL FEATURE SECTION FOR INSTALLATION OPERATING INSTRUCTIONS INTELI TOUCH PAGE 8 COMFORT TOUCH PAGE 12 IntelieTouch 9 9 i J RU The wall control installs in the same manner as an ordinary light switch using an existing junction box and wiring This controller is designed to signal the fan microcomputer as well as perform normal switching operations For this reason the following precautions must be observed 1 Use only the Casablanca W 32 wall control 3 Do not use more than one fan per wall control 2 Do not use any additional control with your Inteli Touch 4 No other light fixtures or electrical appliances may be con fan for example dimmer fan speed control etc nected on the circuit controlled by the W 32 wall control INTELI e TOUCH SINGLE W 32 INSTALLATION or fuse panel before starting installation W 32 is used to describe either white 11 ivory finish 1 Remove the screws and switch plate from the existing 2BLACKS lt L switch box Remove the screws holding the switch in the switch box Pull the existing switch from the switch box to expose the
24. of heated air Press AUTO SECURITY REVERSE to activate and the word WINTER is indicated This puts the fan in the upward airflow direction at the fan s lowest speed Every ten 98 minutes the fan will increase to speed 3 for ten seconds before return ing to the lowest speed UTO SPEED Thermostatic fan speed control SECURITY Lights ON and OFF automatically RI SE Change airflow up or down SAVER Lights turn OFF after 1 hour Pressing any button on the remote will cancel the WINTER SAVER Lights tum OFF alter 1 hour Winter mode except using the light functions MINTER Desf res Neal retti COMFORT TOUCH SECURITY FEATURE Pressing the button will start the Security lighting pro gram The controller beeps and indicates SECURITY The light will automatically turn ON and OFF in a seemingly random man ner over an eight and a quarter hour programmed cycle that is designed to give the home a lived in look SECURITY Regardless of the light setting when switching to the Security mode lights on or off dim or bright the lights will increase a E to high brightness and then begin the Security cycle This cycle 5 is then repeated continuously until cancelled by pressing the button At any time during the Security mode you may adjust the fan SECURITY speed reverse the direction operate in Auto Speed
25. on ball into the canopy opening Check that no wires were pinched Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening CANOPY ELECTRICAL CONNECTI ONS Step 4 Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut Test that the connection is secure by pulling on the wire nut Connect in this order Electrical Connections GREEN leads from mounting plate and fan to GROUND conductor of power source Secure with wire nut WHITE wire from fan to white NEUTRAL wire in ceil ing fixture outlet box Secure with wire nut BLACK power wire from fan to BLACK power wire in ceiling outlet box Secure with wire nut WIRE NUT CANOPY HATCH INSTALLATION Step 5 Tuck the wires into the canopy with the wire nuts pointed upwards so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires CANOPY are clear of the canopy opening HATCH Step 6 Install canopy hatch with the last canopy screw and lock washer To do this LOCK tilt the fan body away from the hatch WASHER opening Tighten the screws firmly by hand only CANOPY Step 7 Straighten the fan then check So to ensure that there is no movement be tween the canopy and ceiling or Hang Tru TILT THE ball and top support shaft FAN TO Note Write down the INSTALL Serial Numbe
26. ously so that a different pattern of lighting is seen each day of the week al To cancel the Home Safe Program turn the off for three seconds INTELI TOUCH OPERATION FAN MI NDER PROGRAM The Fan Minder feature will add to your comfort when used in the bedroom The program reduces the speed of the fan each two hour interval to compensate for the cooling night air To enter the Fan Minder Program 1 Turn the off for at least three seconds Turn the on Immediately operate the buttons in the following sequence LIGHT L LIGHT 7 D FAN STRONG AIRFLOW The fan controller will respond with three descending tones A timer is now initiated and the fan ran minder will reduce one speed for each two hour interval The fan will not however descend below the second lowest speed To cancel the Fan Minder Program turn the off for three seconds You may increase the fan speed by pressing and holding the button until the desired speed is reached then release it The fan will again reduce one speed for each 2 hour interval Fan Minder A PAWN TROUBLESHOOTING Inteli Touch Before Requesting Service Please follow this troubleshooting guide before contacting your dealer for assistance Caring for Finishes For cleaning a soft brush or lint free cloth should be used to prevent scratching the finish A vacuum cleaner brush nozzle
27. r and the LAST model number for future CANOPY reference SCREW BLADE HOLDER SCREW 2 PER BLADE BLADE SCREW 4 PER BLADE Step 8 Attach the blades to the blade holders by first pressing the blade badge into the blade then installing the blade holder using the four blade screws provided for each blade Hand tighten securely BADGE STYLE BLADE HOLDER BLADE SCREW 4 PER BLADE BLADE BLADE HOLDER INSTALLATI ON BLADE Step 9 Rotate the flywheel so that the screw holes can be accessed through the recessed area of the metal plate Attach each blade blade holder assem bly to the motor Tighten securely by hand only 4 5 Blade Combination Flywheel Your Casablanca fan includes our 4 5 combination fly wheel This flywheel accomodates your preference to use either 4 or 5 blades on your fan If you desire a 4 blade fan locate the square counterbores on the fly wheel and use these threaded holes to mount the blades If you desire a 5 blade fan locate the round counterbores on the flywheel and use these threaded holes BLADE HOLDER SCREW 2 PER BLADE 4 blade mounting hole 5 blade mounting hole yD METROPOLITAN Step 10 Remove the three screws on the mounting plate Set aside for Step 12 MOUNTING PLATE INSTALLING THE SWITCH HOUSING CAP Step 11 Line up the three threaded holes in the rim of the switch housing with the three cleara
28. ss LIGHT CONTROL than one second To vary the light brightness ON OFF 1 With lights off press and hold the button After one secondthe momentary press of e lights come on at their lowest level and gradually become brighter the LIGHT button 2 Release the button when the desired brightness level is reached aes The brightness level is now in the fan memory and will automatically come CHANGE BRIGHTNESS on at the same brightness the next time the button is used To PRESS AND HOLD D maintain this level of brightness press the button for less than LIGHT BUTTON one second To lower the brightness turn the lights off then press and hold LONGER THAN ONE the button until the desired brightness level is reached When the SECOND light is on you may increase the brightness level by pressing and holding the button until the desired level is reached then release it AUTOMATI C DEMONSTRATION PROGRAM Programmed into every Inteli Touch Series fan is an Auto A multi tone signal will verify the start of the test program matic Demonstration Program It can be used to fully which proceeds as follows demonstrate and test the operation of the fan Lights slowly increase to full intensity To enter the demonstration program Fan accelerates to speed three with audio tones 1 Turn off for at least three seconds This will Light dims to half intensity clear the fan memory read
29. tact your dealer FAN NOISY DURING OPERATION Tighten glassware and light bulbs Tighten motor housing screws Tighten canopy and mounting crossbar screws DOES NOT RUN ON LOW SPEED If new break in may be required run at higher speed for several days BATTERY LIFE SEEMS SHORT Not using Alkaline batteries Replace with Alkaline batteries TEMPERATURE READINGS Temperature accuracy 3 F FAN DOES NOT RESPOND TO REMOTE CONTROL Power to fan is off wrong remote being used remote channel changed fan receive SET channel changed or fan antenna not receiving See above in locations with two or more fans in different rooms check that controllers are in right rooms change SET channel to match fan change fan SET channel to match remote check antenna connected to RCM check antenna positioned correctly if batteries weak by moving remote close to fan check that remote not laying on metal surface causing weak signal or connect Earth ground to fan FAN APPEARS TO RESPOND TO UNKNOWN SIGNAL OR IS ERRATIC Invalid lower channel SET 2nd remote in area SET to same channel or remote buttons pressed too quickly Be sure SET channel is between 49 and 63 check SET channels of any other remotes at site check if nearby homes have Comfort Touch fans installed remote signal can travel 50 ft and for proper operation of the control you must wait one second between presses AFTER POWER FAILURE FAN AND LIGHTS ARE OFF Normal To immediately restore
30. the fan each speed is indicated by an audible tone of increasing pitch FAN CONTROL To select the desired fan speed 1 With fan off press and hold the button labeled C The fan blades ON OFF will start rotating at the slowest speed and will increase in steps A momentary press amp 2 Release the button when the desired speed is reached of the FAN button The fan speed is now in memory and will automatically come on at the same Gers speed each time the button is used To maintain this level of speed CHANGE SPEED turn the fan on by pressing less than one second To lower speed Press and hold turn fan off then on by pressing and holding the button untilthe button longer than desired speed is reached When the fan is on you may increase the speed by one second pressing and holding the button until the desired speed is reached then release it INTELI TOUCH OPERATION REVERSING AIRFLOW The direction of airflow can be changed from downward to upward or from upward to downward Note A four toned signal indi cates the command was accepted To reverse the airflow by the fan A few seconds later 1 Make sure the is on the fan will slow to a stop and 2 Press the button then reverse direction INTELI TOUCH OPERATION LIGHT To turn the lights off and on press and release the button for le
31. trol LCD display and com pare it to the actual fan operation to confirm correct operation FULL LCD SCREEN DI SPLAY ot 48 W 21 TEMPERATURE COMFORT TOUCH FAN OPERATION The Comfort Touch fan is controlled by the remote control The fan is turned on and off by alternate pushes of the large right hand button As with all button operations an audio tone sounds with each push With the fan on the control display will indicate an up or down moving arrow that shows direction and places a box around the operating speed The two small and buttons below the fan button increase or decrease speed once for each press FAN ON OFF BUTTON AIRFLOW DIRECTION COMFORT TOUCH LIGHT OPERATION The light is turned on and off by alternate pushes of the large left hand button When on the display will indicate the light bulb symbol and a vertical segment display repre senting brightness When the light is on the brightness may be changed by using the small and buttons below the light button Pressing and holding either button will change the brightness continuously Bulb Saver Feature When the light is turned on the brightness is gradually in creased until it reaches the preset level This feature helps extend light bulb life of 8 i LIGHT UP DOWN BRIGHTNESS INDICA
32. y for programming Fan accelerates to full speed with audio tones 2 Turn on Fan reverses at full speed with audio tones 3 Immediately operate the buttons in the following se Fan operates at full speed quence Fan power is reversed with audio tones Fan turns off with audio tones blades coast for a short FAN LIGHT FAN LIGHT time CEN Cam AND amm amm Lights turn off The complete cycle lasts slightly over one minute It will continue to repeat until the is turned off for more than three seconds cancelling the program InteliesTouch 0 01 DA 0 DERE DRA DA The Light Minder program automatically turns OFF the fan mounted lights after two hours To enter the Light Minder Program 1 Turn the OFF for at least three seconds A 2 Turn the ON se 3 Immediately operate the buttons in the following sequence C FN T FAN T C_LIGHT ptd LIGHT 4 A series of tones indicates this command has been accepted The fan and light will operate normally using the buttons to turn them on and off But if the lights are left on they will automatically shut off after two hours To cancel the Light Minder Program turn the off for three seconds INTELI TOUCH OPERATION SAFE EXIT PROGRAM The Safe Exit Program gives you about thirty seconds of light when you turn the lights off enabling you to exit your home before the lights go out
Download Pdf Manuals
Related Search