Carcomm POCKETLOOX CMPC-22 User's Manual
Contents
1. 3 Housing 2 1 The Qvality Line www carcomm nl i2. 5 Electronic and other sophisticated systems for example speed control ABS anti lock brake fuel injection navigation and airbag systems are relatively immune to malfunction caused by PDA or GPS receiver However should you experience false operation of these systems or are in any doubt whatsoever as to their functionality please consult the vehicle s dealer 6 The mobile PDA cradle is suitable for use only in vehicles with a 12V negative grounding Use on other supply voltages or alternative polarity will damage the equipment 7 The PDA should not be left switched on for extended periods without running the vehicle s engine Failure to comply could drain the vehicle s battery Before starting the installation of the mobile PDA cradle please check if the following contents are present Mobile PDA Cradle Rotating Swivel Window Mount Suction Cup Fuse Holder cable with fuse Screw sets Surface cleaner Manual Safety Mount pattern Copyright Carcomm International BV 2006 Subject to change without previous notice All used brandnames are owned by their respective owners T he Cvality Line www carcomm nl Mobile PDA Cradle CMPC 22 Fujitsu Siemens PocketLoox 410 The Quality Line Installing the Mobile PDA Cradle 1 Mount the window suction mount or Safety Mount sold seperataly instructions included with the product To mount the window mount please clean the window and place the window mount
3. in your preferred position Tighten the nut on the base of the mount to make it stick to the window Place the window mount in a position where it doesn t interfere with the operation of the vehicle 2 You can screw the cradle to your mounting part directly or use the included swivel If you use a Safety Mount it may be necessary to drill holes in the Safety Mount to be able to screw on the cradle with or without swivel You can use the pattern on the front page to see the positions where to drill the holes in the Safety Mount Adjust the swivel to optimize your view on the PDA screen and tighten it well OO Align the cradle on the rotating swivel or Safety Mount and screw the cradle onto it with the enclosed screws through the 4 holes Tighten the screws well For permanent installation and connection to the cars ignition power move on to step 5 4 Plug the Cigarette jack into the Cigarette plug adaptor check if the red light of the cigarette plug is lighted Now you are able to charge your PDA in the mobile cradle Move on to step 7 5 Disassemble the Cigarette plug or cut it from the wiring loom and strip the wires The cradle is also available with a fuse in the wiring loom instead of cigarette plug 6 Now the red wire with fuse needs to be connected to the red wire from the cradle wiring loom Then the other side of the fuse s wire needs to be connected to the vehicle s 12V Ignition controlled voltage 15 to
4. Mobile PDA Cradle CMPC 22 Fujitsu Siemens PocketLoox 410 Introduction This installation manual has been prepared to provide the basic information needed to install the CMPC 22 This manual is not intended to be definitive because there are different models and types of vehicles which will require different installation work The information given is for general guidance only The terms of warranty demand that this mobile PDA cradle is installed by an experienced installer An end user should never attempt to install this mobile PDA cradle without professional assistance as the installation requires special tools and knowledge Note Thoroughly read the manual before beginning the installation procedure WARNINGS 1 Ensure that the vehicle s battery is disconnected before you start the installation procedure and that it remains disconnected during the procedure 2 Do not smoke or use open flames when working near the vehicle s fuel system Compatible devices 3 Ensure that the vehicle s electrical cables hydraulic lines fuel lines and safety i Fujitsu Siemens PocketLoox 410 equipment are not damaged during the installation Fujitsu Siemens PocketLoox 420 Fujitsu Siemens PocketLoox N500 4 Ensure that normal control and operation of the vehicle is not obstructed by the rau emen Rokoo N20 installation particularly the brakes and steering Ensure that airbag operation is not qu isu Stamans Pocialloax Css obstructed
5. avoid draining the vehicle s battery when the vehicle is not used for a long time The black wire needs to be connected to the Negative Ground of the vehicle Step 3 7 Slide the PDA into the cradle slowly and make sure the PDA is centred well above the connector Then press it over the connector gently When removing the PDA from the cradle use one hand to hold the cradle and other hand to pull the PDA out of it Connecting a Carcomm Euro Navigator wired GPS Receiver optional Connect the PS 2 plug from the GPS to the PS 2 Jack from the PDA cradle The PDA will get the data from the GPS receiver and the cradle will supply 5V power to the GPS Receiver The GPS receiver can be connected plug amp play to the PDA Cradle Mount the GPS on the dashboard with supplied hook amp loop tape or under the dashboard with included dual sided tape Make sure it has a clear unobstructed view to the sky and make sure that the GPS is positioned so that the top is facing upwards Now you re able to setup and use your navigation software In cars with UV protected windows the reception will be influenced and decreased How to connect another brand GPS Receiver When connecting another brand GPS Receiver please check the tables below for the pin assignment of the PS 2 Female connector Or check our website for adaptor cables Step 7 Note The TX and RX connections have to be twisted to the GPS connector PS 2 Female Frontview 6 9 4 6 4 3 2
Download Pdf Manuals
Related Search