Canon LV-5210 Instruction Guide
Contents
1. ES LV CL08 03 8 26 7 40 PM 2 1 B M4x40 1 A M4X12 3 di lt CY G2 NORMNBEZA4V w TAA 3 4 FS2. LV CL08 03 8 26 7 40 PM 4 mm mm 127 5 1855 p A 1 eJ CN O fp 5 n Co EET E i 4 p 9FL 106 E 40 602 70 802 90 1002 1102 1202 150 200 2502 00 Ami rem 2am sem sem sem aom 44m aen eom 5 LV CL08 03 8 26 7 40 PM 5 Mounting Hanger for Low Ceilings Assembly Installation Manual occa a mm LY CLO8 Make sure to ask a company specializing in installation work to install the hanger This mounting hanger is specifically for the projectors shown above It cannot be used for any other equipment Do not place or hang any other object on this mounting hanger Do
3. A M4X 12mm CA FET 2 LV CL08 03 8 26 7 40 PM 3 Edge WAFL G60 15 360 ARI
4. QUE 1 7kg A 11 B 1 1 BG 1 A B A 3 B 1 2 CO 4 A
5. LV CL08 03 8 26 7 40 PM 1 LY CLO8 LV 7215 LV 7210 LV 5210 Kis a
6. Loosen the angle adjusting screws before adjusting the angle again If the angle is not proper adjust the angle again After adjustment confirm that the projector is fixed securely LV CL08 03 8 26 7 40 PM 8 Front view Unit mm Side view Unit mm 127 5 185 5 122 ai S 206 5 173 Q Va Ceiling hanging fitting mounting dimensions Hole 4 29 106 E Approximate projection distance areen size 40 60 70 80 90 100 110 120 150 200 250 300 Maximum zoom 1 0m 1 5m 1 8m 2 0m 2 3m 2 5m 2 8m 3 1m 3 8m 5 1m 6 4m 7 7m Minimum zoom 1 6m 4 0m 4 8m 6 0m Each approximate projection distance is a calculated value based on lens design specifications An error of approximately 5 maximum may occur due to lens quality etc
7. body mounting fitting to which the projector is attached into the ceiling hanging fitting that is attached to the ceiling Then fix the main body mounting fitting securely to the ceiling hanging fitting with four A screws included in the package Caution During this procedure take care not to drop the projector Since the projector is hung only temporarily it is not yet secured When wiring make sure not to let cables or other items block the air inlet or the exhaust port This may raise the inside temperature and result in a malfunction Adjusting the projection position Refer to Fig 2 Adjust the projection position so that an image is projected in the center of the screen Then tighten the angle adjusting screws securely using the hexagon wrench included in the package If fine adjustment of the angle cannot be smoothly attained loosen the angle adjusting screws with the hexagon wrench Then use the angle fine adjustment screw This will allow smooth fine adjustment LV CL08 03 8 26 7 40 PM 6 Fig 1 Assembly Screws A En Plus screw with round head M4 x 12 3 pcs with spring washer and flat washer Screw B Plus screw with round head M4 x 40 1 pc with spring washer and flat washer Main body mounting fitting 1 pc Projector main body pe a gt P Adjuster 1 Pull out the adjus
8. not let children hang on it Assemble and install this mounting hanger correctly in accordance with this manual Make sure to observe the cautions given here When displaying the projector by hanging it from the ceiling using this mounting hanger the INSTALLATION ceiling should have sufficient strength to support both the projector and the mounting hanger Before installation check the weight of the projector and the mounting hanger then CAUTIONS confirm the strength of the ceiling If the ceiling does not have sufficient strength be sure to sufficiently reinforce it Make sure to install this mounting hanger from a ceiling that is level Do not hang it from an inclined ceiling Qn order to prevent swaying caused by earthquakes or vibration take proper anti swaying steps using wires etc during installation The total weight of this mounting hanger s main body is 1 7 kg Screw AN 11 pcs Screw B 1 pc Wire 2 pcs Hexagon Wrench 1 pc Assembly Parte included dde 0 Installation Manual in package i LY Assembly and installation procedure j Refer to Fig 1 1 Turn over the projector main body and attach it to the main body mounting fitting with screws A and B screw A 3 pcs screw B 1 pc D 2 Attach the drop prevention wires 3 Attach the ceiling mounting fitting to the ceiling Refer to the ceiling hanging fitting attachment dimensional drawing 4 Slide the main
9. ter from the 2 Hang securely the drop 3 Tighten securely the wire clamp 4 Attach the drop prevention wire to projector main body prevention wire included in the with the drop prevention wire the main body mounting fitting package to the adjuster in the and push down the adjuster in with two A screws M4 x 12 mm main body 2 positions the main body included in the package Attach the drop prevention wire on the opposite side in the same way Measures to prevent the projector from falling Make sure to take measures to prevent the projector main body from falling as explained here Ceiling hanging Fix securely the main body fitting mounting fitting to the ceiling hanging fitting with four A D screws M4 x 12 mm included in the package Main body mounting fitting LV CL08 03 8 26 7 40 PM 7 Fig 2 Adjustment This screw facilitates fine adjustment of the projection angle while the projector is half fixed After determining the projection angle make sure to fix securely the projector with the angle adjusting screws Angle adjusting screws with hexagon socket Rotated 360 to the left and right NET Tilted 15 in the 360 rotation range 15 15 CAUTION After the projector angle is fixed once if the angle is adjusted again in the fixed status the fixed area may be deformed and N adjustment might no longer be possible
Download Pdf Manuals
Related Search