Cambridge Audio Topaz SR10 User's Manual
Contents
1. Used for AM FM modes The preset buttons are used to select user stored station presets Pressing a preset button once will select one of the first 5 preset then pressing the same preset button again will toggle to the next preset 1 and then 6 for instance These presets are stored separately for each waveband i e there are 10 for FM and 10 for AM press the FM AM button to switch between bands and sets of 10 presets Note As well as these 10 per band available directly from the front panel buttons a further 5 presets 11 15 per band can also be accessed by using the up down buttons to cycle through all 15 presets 7 Display Used to display information such as the selected input source volume and tone balance levels When the FM or AM tuner input is selected the radio frequency or RDS station name will be displayed Note When first purchased the display will have a protective film over the top Peel this off for a clear display BD DVD 3 8 MP3 Aux 00000 Phono Speaker A B 4 9 5 10 Speaker A B button The Speaker A B button toggles between the two sets of loudspeaker terminals The options are speaker A only speaker B only speaker A and B together and both sets of speakers off Note Speaker off is different to the mute function as the Rec Out and Headphones outputs are still enabled Menu button Pressing this once will select the Bass option Pressing a second tim2. Topaz SR10 Cambridge Audio Your music our passion Cambridge Audio Contents In tl OQ HO LO s a e d kek emer terme a DA Se l na et c ke Wu a M w de d akan renter an e 2 Important safety INStruUctionS a4 K K K Zllll kk kk kak k k k AKA A KAK KAWA 3 Limited dezlal a E 4 Rear panel GONE CONS sis iii i i i ii i i i KH KA Kina 5 aa S aes i i i i r 5 Front panel controlS i sskasiiniisinisiissiiast iausi ias us iui sa airis ai 6 Remote COMMU Ola Saias ais iii i i i i i i i i i i eons 7 CONNECUONS Sy adis a a i i aa i a a a a as 8 Operating LAC UE LOS ie rikiai ai i ia a i 10 Technical specifications saisiti iusinninis aks ii ii i i i kk KAKA KA KK KK KA 11 IS SO LINE rere i a i i eee 11 Introduction Thank you for purchasing this Cambridge Audio Topaz SR10 Stereo Receiver We are confident that you will enjoy many years of listening pleasure from it Like all Cambridge Audio products the SR10 adheres to three core principles stunning performance ease of use and incredible value Our usual attention to detail is present with a completely discrete high power bipolar transistor based power amplifier very quiet speed controlled fan cooling and a custom low flux toroidal transformer for audiophile audio performance The built in FM AM tuner features RDS for station name display on FM stations that support this function The unit can support a wide range of external sources and a fron
3. Main Room E a SR10 O EO Hi i SSS Ground W34 ya C JC IL FE 2 C 2 4 JC IEG J wn na 9 9 55535 66 6 3555 B O e g 99999 hihid S 2 Speaker B S Room Two Bi wire connections Note If your loudspeakers are equipped with two sets of terminals then it is Speaker A and B must both be selected for this type of connection to possible to connect them in the bi wire configuration Bi wiring sends the bass and treble frequencies down separate speaker cables resulting in a clearer more focussed sound Remove the bi wire link on the speaker terminals before connecting Refer to your speakers manual for more information work Black Red Red Black Black Red Black Red l Right 5 i 5 O O Left speaker Mi speaker HF 9 0 HF vau HF 9 HF P LF LF 80 LF O LF O O R O O Black Red Black Red Cambridge Audio Operating instructions After making any connections to your unit activate the Topaz SR10 by pressing the On Off button on the front of the unit Setting the source Press the Source bu
4. assurer que les bornes de l enceinte sont Designed and engineered in London England Serial Number Label Removed AN N H AN FAA T T A entierement serres Topaz SR10 Stereo Receiver T A O E per Peake Us Power Consumption 500W www cambridge audio com Mains Voltage Selector Switch YA AA ea sen era Ground G 14314 91 C 2 C J C A az e yr C RE Era A k Europe AM 522kHz 1629kHz C 5 C C F US AM 530kHz 1710kHz 6 A C gee 2D No 7 AC 6 k lt J A C ae D Q C D This device complies with part 15 of the FCC go O GAd aa_xAy EdIN ououd NIN 310 994 di deviy be not sales a ler erehan E way 1 gt 1 ee 000 00 P 1 1 C i a N i B iC ae ser i i Nen en 1431 O 6 8 8 t se i gt OC WED KO 9 amp gonea e A cD BD DVD MP3 Aux MM Phono Rec Out BLA e cee dG et Made under licence in China 2 G 7 4 Audio inputs Aerials These inputs are suitable for any line level source equipment such as the audio outputs of CD players BD DVD players etc 2 Phono input This input has a built in phono stage Record players fitted with Phono Cartridges of the Moving Magnet MM or high output Moving Coil MC type between 2 6mV output and 30 50k load impedance can be used Low output Moving Coil types lt 1mV and usually 10 1000 ohm load impedance cannot be directly connected and will require a matching transformer or head amp Plea
5. defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use with only the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus O When a cart is used use caution when moving the cart AA apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as the power supply cord or plug having been damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped WARNING To reduce the risk of fire or electric shock do not expose this unit to rain or moisture Batteries battery pack or batteries installed shall not be exposed to exc
6. use we recommend that you set the Topaz SR10 to Auto mode Press the Mode Store button on the front of the unit This button cycles through Preset Auto and Manual modes 10 Mode Store Z When Auto mode has been selected press the M4 button to scroll down through the station frequencies or press the button to scroll up through the station frequencies The tuner will stop at the first strong signal it finds To move to another station simply press the M4 or gt gt button again Setting presets Radio stations can be stored into the memory presets for easy access You can store up to 15 presets for each band i e 15 presets for the AM band plus 15 presets for the FM band Tune to the station you wish to store and hold down the Mode Store button on the front of the unit The display on the unit will flash the next available preset Mode Store P Press the Mode Store button again to store the preset The available preset will stop flashing to indicate that the station has been stored To change the preset number simply press and hold the Mode Store button to enter store mode then select any preset number you require with the M4 and D keys then press the Mode Store button again to actually save the preset To recall a stored preset simply press the number on the remote control that corresponds with the preset Each of the preset buttons can select two presets To select the second preset on the butt
7. will automatically mute the loudspeaker outputs 3 l a PPI Skip Scan buttons The skip scan buttons are used when the FM AM tuner is selected These buttons have different uses depending on the mode selected In Preset mode Steps up or down through the user stored presets In Auto mode Searches for the previous or next available station The unit stops at the next strong signal it finds In Manual mode Allows manual stepping up or down of the frequency Note When Preset mode is activated the unit will automatically tune to the first available preset 4 Mode Store button Used for AM FM mode Press to cycle the tuning mode between Preset Auto and Manual modes Pressing and holding the button will allow the current selected station frequency to be stored in the preset bank First press and hold the button then use the l4 gt or Preset buttons to select the preset location for the station to be stored to Press the Mode Store button again to confirm and store the preset Note In Store mode if no button is pressed for a while the unit will come out of Store mode and the preset will not be saved 5 Input source buttons CD BD DVD MP3 Aux FM AM Phono Press the relevant source button to select the desired input source Note The FM AM source is built into the SR10 This button toggles between the FM mode and AM mode when pressed more than once 6 Preset buttons 1 6 2 7 3 8 4 9 5 10
8. 1kg 17 8lbs European AM 522 1629kHz FM 87 5 1O8MHz US AM 530 1710kHz FM 87 5 108MHz FM 75 ohms Coaxial AM 300 ohms wire loop single wire 60dB typical FM lt 0 4 1kHz 5OkHz deviation FM mono lt 0 6 1kHz 50OkHz deviation FM stereo Check aerial connections and placements Check speaker connections There is a hum coming from the speaker Ensure that all cable connections are secure particularly ground shield connections For turntables There is unwanted background noise and interference Move the unit away from other electrical equipment that is likely to cause interference Re orientate the aerial Ensure that all cable connections are secure particularly ground shield connections for turntables The remote handset will not function Check that the batteries have not expired Ensure that nothing is blocking the remote sensor Over temperature protection The unit has an over temperature and shutdown protection If the unit is continuously used for a long period and over heats the unit will shut down Leave the unit ON for 10 minutes to cool down then turn the unit off and on to continue listening If the problem persists then the unit is being over driven Reduce the volume level and ensure the unit is in an open ventilated area to resolve the problem Use of two pairs of speakers which are less than 8 Ohms can cause overloading and is not recommended In the event tha
9. airs will void this Warranty This Warranty does not cover products sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER CAMBRIDGE AUDIO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other statutory rights which vary from state to state or country to country For any service in or out of warranty please contact your dealer Plug Fitting Instructions UK Only The cord supplied with this appliance is factory fitted with a UK mains plug fitted with a 3 amp fuse inside If it is necessary to change the fuse it is important that a 3 amp one is used If the plug needs to be changed because it is not suitable for your socket or becomes damaged it should be cut off and an appropriate plug fitted following the wiring instructions below The plug must then be disposed of safely as insertion into a mains socket is likely to c
10. ause an electrical hazard Should it be necessary to fit a 3 pin BS mains plug to the power cord the wires should be fitted as shown in this diagram The colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug Connect them as follows The wire which is coloured BLUE must be GREEN E connected to the terminal which is marked YELLOW with the letter N or coloured BLACK FUSE The wire which is coloured BROWN must be BLUE connected to the terminal which is marked N with the letter L or coloured RED The wire which is coloured GREEN YELLOW bn must be connected to the terminal which is marked with the letter E or coloured GREEN GRIP If a 13 amp BS 1363 plug is used a 3 amp fuse must be fitted or if any other type of plug is used a 3 amp fuse must be fitted either in the plug or adaptor or on the distribution board Rear panel connections Topaz SR10 N 92 7 AS FM 7562 AM 3000 Service Port EE opa E E E Cambridge Audio Caution Veuillez s
11. comply with the F limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help ENGLISH Cambridge Audio Ventilation IMPORTANT The unit will become hot when in use Do not stack multiple units on top of each other Do not place in an enclosed area such as a bookcase or in a cabinet without sufficient ventilation Ensure that small objects do not fall through any ventilation grille If this happens switch off immediately disconnect from the mains supply and contact your dealer for ad
12. duct as easy i as possible Information in this document has been carefully checked 1 for accuracy at the time of printing however Cambridge Audio s policy gt is one of continuous improvement therefore design and specifications 1 l are subject to change without prior notice i z This document contains proprietary information protected by copyright 1 All rights are reserved No part of this manual may be reproduced by any I mechanical electronic or other means in any form without prior written 1 permission of the manufacturer All trademarks and registered i trademarks are the property of their respective owners I 1 O Copyright Cambridge Audio Ltd 2009 i I 1 _ a E at 4 i gt Important safety instructions For your own Safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply They will also enable you to get the best performance from and prolong the life of the unit 1 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth N O Oh EB W N Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not
13. e will select the Treble option and pressing a third time will select the Balance option When one of these options is selected the volume control will adjust the level If nothing is pressed for a while the source will be displayed and the volume control will go back to controlling the volume level Infrared sensor Receives IR commands from the supplied remote control An unobstructed line of sight between the remote control and the sensor is required 14 Volume control Use to increase or decrease the level of the sound from the outputs of the unit This controls the volume level of the loudspeakers and headphones It does not affect the level of the Rec Out output The volume control will also change the level of bass treble and balance in the menu options 12 MP3 input socket This source input allows you to connect a portable audio device such as an MP3 player directly into the front of the unit using a 3 5mm stereo jack Once plugged in this input is automatically selected although other inputs can still be selected once a stereo jack is plugged in The MP3 AUX button on the front of the unit will select this input whilst a stereo jack is plugged in Note Plugging a source into the front panel MP3 input overrides the Aux input Simply remove the jack from the front panel to automatically re enable the Aux input Also note that as the output level of MP3 players tends to be quite low the SR10 adds 10dB to the cu
14. enu Toggles between Bass Treble and Balance options Use the volume buttons to change the level of the selected option Preset buttons 1 5 2 6 3 7 4 8 Used when FM or AM is selected These select user stored station presets Pressing a preset button once will select one of the first 4 presets then pressing the same preset button again will toggle to the next preset 8 presets are available directly from the remote further presets can be selected in Preset mode by using the Skip Scan buttons Source buttons CD FM AM BD DVD MP3 Aux Phono Press the relevant button to select the desired music source Topaz CD5 CD10 rm Presets is Le 12 4 gt Repeat Remain Qe BD DVD MP3 Aux Cambridge Audio SR10 ENGLISH Cambridge Audio Connections Loudspeakers Check the impedance of your speakers When using a pair of speakers you can use types with an impedance of between 4 and 8 Ohms When using two pairs of speakers you must use types with an impedance of 8 Ohms each see later section The red coloured speaker terminals are positive and the black speaker terminals are negative Make sure correct polarity is maintained at each speaker connector or the sound can become weak and phasey with little bass Using bare wire connections Prepare the speaker cords for connection by stripping off approximately 10mm 3 87 or les
15. essive heat such as sunshine fire or the like The unit must be installed in a manner that makes disconnection of the mains plug from the mains socket outlet or appliance connector from the rear of the unit possible Where the mains plug is used as the disconnect device the disconnect device shall remain readily operable Only use the mains cord supplied with this unit Please ensure there is ample ventilation at least 10cm clearance all round Do not put any objects on top of this unit Do not situate it on a rug or other soft surface and do not obstruct any air inlets or outlet grilles Do not cover the ventilation grilles with items such as newspapers tablecloths curtains etc This unit must not be used near water or exposed to dripping or splashing water or other liquids No objects filled with liquid such as vases shall be placed on the unit Topaz SR10 Vorm ffnen des ger tes Ne pas ouvrir Netzstecker ziehen Risk of electric Risque de choc shock electrique Do not open A The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions i
16. multi room system Note When using two pairs of speakers use speakers with a nominal impedance of 8 ohms 7 Voltage select switch For servicing use only AC power socket Once all connections are complete plug the AC power cable into an appropriate mains socket and turn the unit on Note The SR10 is supplied with a temporary aerial for initial use For permanent use outdoor aerials are highly recommended AM loop aerial Connect each end of the single length antenna to the antenna terminals Place the antenna as far from the main system as possible to prevent unwanted noise and to obtain optimum reception If the AM loop aerial provided does not provide sufficient reception it may be necessary to use an outdoor AM aerial FM aerial Connect the supplied aerial to the FM 75 ohm socket Extend and move the aerial lead around until you get the best reception For continued use we strongly recommend using a 75 ohm outdoor FM aerial ENGLISH Cambridge Audio Front panel controls Cambridge Audio Topaz SR10 Stereo Receiver Oo A amp On Off O ee Phones 144 gt Pl Mode Store 1 6 2 7 1 Power On Off Switches the unit on or off 2 Headphones socket Allows for the connection of stereo headphones with a inch jack plug Headphones with an impedance of between 32 and 600 ohms are recommended Note Plugging in headphones
17. n the service literature relevant to this appliance The symbol on this product indicates that it is of CLASS Il double insulated construction WEEE symbol The crossed out wheeled bin is the European Union symbol for indicating separate collection for electrical and electronic equipment This product contains electrical and electronic equipment which should be reused recycled or recovered and should not be disposed of with unsorted regular waste Please return the unit or contact the authorised dealer from whom you purchased this product for more information C CE mark This product complies with European Low Voltage 2006 95 EC Electromagnetic Compatibility 2004 108 EC and Environmentally friendly design of Energy using Products 2005 32 EC Directives when used and installed according to this instruction manual For continued compliance only Cambridge Audio accessories should be used with this product and servicing must be referred to qualified service personnel C Tick mark This product meets the Australian Communications Authority s Radio communications and EMC requirements G Ross Test Stamp This product meets Russian electronic safety approvals FCC regulations NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT This equipment has been tested and found to
18. on press the button again and this will toggle to the second preset Preses AZ lt To load a stored preset from the front of the unit simply press the number on the front the unit or remote that corresponds with the preset To access the second preset represented by the button you must press and hold the button UN Note You can only access stored presets 1 8 on the remote preset buttons You can access stored presets 1 10 on the front panel preset buttons To access all presets set the mode to Preset mode with the Mode button on the remote control or Mode Store button on the front panel and use the M4 or gt buttons This will allow access to the full 15 AM stored presets or 15 FM stored presets Resetting tuner presets To clear all stored presets for both AM and FM press and hold both the 5 10 and Menu buttons at the same time The unit will display Reset Restart the unit by powering off and on Menu S gt Topaz SR10 Troubleshooting Tuner settings It is possible to change the tuner region settings for this unit This can be necessary if the unit has been moved to a different country There is no power Ensure the AC power cord is connected securely ENGLISH Ensure the plug is fully inserted into the wall socket and is switched on Two settings are possible which set the correct de emphasis and tuning steps for either North America or Europe Rest of the w
19. orld Check fuse in the mains plug or adaptor Note Changing the tuner settings will clear all stored presets When Check the power is on at the front of the unit moving the unit to another region the Voltage Select switch must be set to the correct mains supply voltage by an authorized dealer There is no sound Menu Check the correct input is selected S Check that the speakers are connected correctly If using the tuner check aerial connections and an available station is selected Check the unit is not in mute mode Check the Speaker A B configuration matches your speakers Press and hold both the 4 9 and Menu buttons at the same time The display will show the software revision and followed by either a letter A which represents North America or a letter E which represents The sound is distorted Europe Rest of the world Restart the unit by powering off and on Technical specifications Power output THD unweighted Frequency response 1dB S N ratio ref 1W Input impedances Power Amp damping factor Max power consumption Bass Treble controls Dimensions Weight Tuners Bands Aerial inputs Signal to noise Distortion 85 watts into 8Q lt 0 01 1kHz 80 of rated power lt 0 15 20Hz 20kHz 80 of rated power 5Hz 50kHz gt 82dB unweighted 47k ohms gt 50 500W Shelving ultimate boost cut 10dB 100Hz and 20kHz 110 x 430 x 340mm 4 3 x 16 9 x 13 4 8
20. rchase To obtain warranty service please contact the Cambridge Audio authorised dealer from which you purchased this product If your dealer is not equipped to perform the repair of your Cambridge Audio product it can be returned by your dealer to Cambridge Audio or an authorised Cambridge Audio service agent You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the warranty period must be presented to obtain warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a Cambridge Audio authorised dealer You may call Cambridge Audio or your local country Cambridge Audio distributor to confirm that you have an unaltered serial number and or you purchased from a Cambridge Audio authorised dealer This Warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installation or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer or authorised service agent which is authorised to do Cambridge Audio warranty work Any unauthorised rep
21. rrent volume setting when and only when the MP3 input is selected Remote control The Topaz SR10 is supplied with a remote control that operates this unit and its built in tuner In addition the buttons with Blue coloured icons can operate a matching Topaz CD5 or CD10 player Always use Alkaline batteries CD5 CD10 Blue coloured icons To operate the Topaz CD5 or CD10 players only For more information refer to the Topaz CD5 and CD10 user s manual IK Mute Mutes audio on the unit Press again to cancel mute Speaker A B Toggles between the selected loudspeaker terminals speaker A only speaker B only speaker A and B together or all speakers off Stereo Mono Used only when FM is selected Toggles between FM stereo output and FM mono output For low quality stereo FM signals selecting mono can usually reduce the noise Note Some FM stations are mono only and selecting Stereo will have no affect on these Mode Used for AM FM mode Press to cycle the tuning mode between Preset Auto and Manual modes A Volume Increases or decreases the volume of the unit Also used to change the bass treble and balance settings when these are selected K gt I Skip Used when FM or AM is selected In Preset mode Steps up or down through the user stored presets In Auto mode Search for the previous or next available station with a strong signal In Manual mode Adjusts the frequency in steps for fine tuning M
22. s of the outer insulation More than 10mm could cause a Short circuit Twist the wires tightly together so there are no loose ends Unscrew the speaker terminal insert the speaker cable tighten the terminal and secure the cable Right speaker O O O O Note All connections are made using standard loudspeaker cable Basic connection The diagram below shows the basic connection of your unit to a CD player and a turntable and a pair of loudspeakers O O Left speaker SR10 Left CD player Turntable Topaz SR10 T Speaker B connections Either A or B or both A and B may be selected for use 2 The Speaker B connections on the back of the amplifier allow for a second Note When using two pairs of speakers use speakers with a nominal S set of speakers to be used i e speakers located in another room impedance of 8 ohms each The Speaker A B button on the front panel and remote control allows the two sets of speakers to be toggled on and off Refer to the Front Panel or Remote Control section of this Manual for more information on the Speaker A B operation O O Speaker A O O E a
23. se consult your dealer for details The Service Por Cambridge Audio ground terminals on both the record player and the SR10 should be connected where possible with a ground wire for lowest noise hum pickup 3 Rec Out Connect to the recording input of a tape deck CD recorder input etc 4 AM FM antenna Tuner aerial connections for picking up radio signals Refer to the Connections section of this manual For permanent use outdoor AM FM aerials are highly recommended 5 Service port For servicing use only Do not connect anything here as it may result in damage 6 Loudspeaker terminals Two sets of loudspeaker terminals are available A main loudspeaker terminals top row and B secondary switchable loudspeaker terminals bottom row Connect the wires from your left channel loudspeaker to the Left positive and negative terminals and the wires from the right channel loudspeaker to the Right positive and negative terminals In each case the red terminal is the positive output and the black terminal is the negative output Care should be taken to ensure no stray strands of wire are shorting speaker outputs together Please ensure that the loudspeaker terminals have been tightened adequately to provide a good electrical connection It is possible for the sound quality to be affected if the screw terminals are loose The use of A and B speakers affords you an easy and inexpensive way to create a simple
24. shock Overloaded AC outlets extension cords frayed power cords damaged or cracked wire insulation and broken plugs are dangerous They may result in a shock or fire hazard Be sure to insert each power cord securely To prevent hum and noise do not bundle the interconnect leads with the power cord or speaker leads Cleaning To clean the unit wipe its case with a dry lint free cloth Do not use any cleaning fluids containing alcohol ammonia or abrasives Do not spray an aerosol at or near the unit Battery disposal Please dispose of any discharged batteries according to local environmental electronic waste disposal guidelines Loudspeakers Before making any connections to loudspeakers make sure all power is turned off and only use suitable interconnects Servicing These units are not user serviceable never attempt to repair disassemble or reconstruct the unit if there seems to be a problem A serious electric shock could result if this precautionary measure is ignored In the event of a problem or failure please contact your dealer Limited warranty Cambridge Audio warrants this product to be free from defects in materials and workmanship Subject to the terms set forth below Cambridge Audio will repair or replace at Cambridge Audio s option this product or any defective parts in this product Warranty periods may vary from country to country If in doubt consult your dealer and ensure that you retain proof of pu
25. t panel MP3 Portable Media Player input has been fitted which can be used with the headphone or line level outputs of most portable players The supplied remote control can control this receiver and its built in tuner plus the matching CD5 or CD10 CD players if required Part of our new Topaz range this product also features a new casework design with braced front panel rigid wrap over lid assembly and carefully designed mechanicals for resonance control Your receiver can only be as good as the system it is connected to Please do not compromise on the quality of your source equipment speakers or cabling Naturally we particularly recommend source and speaker models from the Cambridge Audio range which have been designed to the same exacting standards as this product Your dealer can also supply excellent quality Cambridge Audio interconnects to ensure your system realises its full potential Thank you for taking the time to read this manual we recommend you keep it for future reference Nauda Gr Matthew Bramble Cambridge Audio Technical Director and the SR10 design team ee N i 1 Make sure you register your purchase i l 1 1 1 Visit www cambridge audio com sts I i l i By registering you ll be the first to know about 1 1 e Future product releases 1 e Software upgrades i e News events and exclusive offers plus L L i competitions 1 1 1 This guide is designed to make installing and using this pro
26. t the above solutions do not remedy your problem please consult our frequently asked questions FAQ section on our website www cambridge audio com sts faqs For all servicing in or out of warranty please contact your dealer 11 Cambridge Audio is a brand of Audio Partnership Plc Registered Office Gallery Court Hankey Place London SE1 4BB United Kingdom Registered in England No 2953313 www cambridge audio com 6 2009 Cambridge Audio Ltd N LO 0 LC LC N Q lt
27. tton on the front of the unit corresponding to your desired source Alternatively you may use the appropriate button on the remote control MP3 Aux E Adjusting the volume Use either the Volume Up Down buttons on the remote control or the Volume control on the front of your unit system to change the volume level The newly selected level will be indicated briefly on the front display The volume is displayed in minus dB where OdB is the highest level A progressively larger negative number indicates the volume is being reduced Adjusting the audio settings Adjustments to the bass treble and balance can be made as follows 1 To enter the audio menu Press either the Menu button on the front of the unit or on the remote control 2 Step through the available settings by pressing the Menu button The settings available are in order Bass Treble and Balance 3 When you wish to make an adjustment for bass treble or balance simply rotate the Volume control or use the Volume control buttons on the remote control 4 To exit wait for five seconds until the unit returns to normal mode Tuning and listening to the built in tuner Select the Tuner source using the FM AM button on the front of the unit or directly by pressing the FM or AM buttons on the remote FM AM S Repeatedly pressing the FM AM button on the front of the unit switches between FM and AM modes Note For ease of tuning on first time
28. vice Positioning Choose the installation location carefully Avoid placing it in direct sunlight or close to a source of heat No naked flame sources such as lighted candles should be placed on the unit Also avoid locations subject to vibration and excessive dust cold or moisture The unit can be used ina moderate climate This unit must be installed on a sturdy level surface Do not place in a sealed area such as a bookcase or in a cabinet Do not place the unit on an unstable surface or shelf The unit may fall causing serious injury to a child or adult as well as serious damage to the product Do not place other equipment on top of the unit Due to stray magnetic fields turntables or CRT TVs should not be located nearby due to possible interference Electronic audio components have a running in period of around a week if used several hours per day This will allow the new components to settle down the sonic properties will improve over this time Power sources The unit should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company To turn the unit off switch off on the front panel If you do not intend to use this unit for a long period of time unplug it from the mains socket Overloading Do not overload wall outlets or extension cord as this can result in a risk of fire or electric
Download Pdf Manuals
Related Search