Butler PIG DESIGN 92647 User's Manual
Contents
1. Suther correction ROUND PARK BENCH Pig Design WOE 92647 ASSEMBLY INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Manual Revised 04 05 SPECIFICATIONS Construction Cast Iron Frame w Black Finish Finished Slats Varnished Wooden Slats Design Lazy Pig Eating Daisies Seat Size 20 1 4 W X 17 1 2 D X 23 172 H 16 1 4 H from ground Overall Dimensions 24 1 8 L X 21 9 4 WX 34 5 6 H Weight 60 Lbs Weight Capacity 330 Lbs SAVE THIS MANUAL You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference SAFETY WARNINGS AND PRECAUTIONS 1 KEEPWORK AREA CLEAN Cluttered areas invite injuries 2 OBSERVE WORK AREA CONDITIONS Keep work area well lighted 3 DO NOT ATTEMPT TO ASSEMBLE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to2. determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not attempt to assemble this product 4 STAY ALERT Watch what you are doing at all times Use common sense Do not assemble this product when you are tired or distracted from the job at hand 5 CHECK FOR DAMAGED PARTS Before using any product any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for any broken or damaged parts and any other conditions that may affect its operation Check wood for any stains or flaws Replace or repair damaged or worn parts immediately 6 USE EYE AND EAR PROTECTION Always wear ANSI approved impact safety goggles when assembling this product 7 WEAR GLOVES AND AVOID SHARP EDGES WHEN ASSEMBLING 8 MAKE CERTAIN TO SET THE BENCH ON A FLAT EVEN AND SOLID SURFACE Place product on carpet or grass Concrete could injure people if Bench is tipped over 9 ALWAYS CHECK HARDWARE AND ASSEMBLED PARTS AFTER ASSEMBLING All connections should be tight and hardware tightened We recommend assembling the Bench outdoors Two adults are better at assembling this product 10 DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY OF 330 LBS 11 DO NOT ALLOW CHILDREN TO PLAY ON STAND UPON OR CLIMB ON THE BENCH SKU 92647 For technical questions please call 1 800 444 3353 Page 2 12 THIS PRODUCT IS MANUFACTURED OF CAST IRON Do not force any par
3. eck periodically to be sure all hardware stays tightened PARTS LIST DESCRIPTION Round Back Assembly End Pieces Left amp Right Seat Slats Bolt 6 x 30mm Nuts 6mm amp Washers 6mm Bolt 6 x 20mm amp Washers 6mm Support Bracket Self Tap Screw 4 x 10mm Bolt 8 x 30mm Nuts 8mm amp Washers 8mm ASSEMBLY ILLUSTRATION Part 2 L Part 7 not shown Part 6 not shown Pars5 M Part rounded slat Seat Slates 3 Part 8 MAINTENANCE For better and safer performance keep all parts of this product clean and dry at all times THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 92647 For technical questions please call 1 800 444 3353 Page 5
4. f the Bench Use the Bolts Washers and Nuts 4 to attach See Figure 1 Note It may become necessary to enlarge the holes in the End Pieces 2 Clear the hole of paint by sliding a bolt through the hole or using a drill before assembly Round Back Assembly 1 ssembly 1 End Piece Right Side 2 R Bolts 4 Seat Slats 3 Round Stat in Front Figure T SKU 92647 For technical questions please call 1 800 444 3353 Page 3 2 Attach the Round Back Assembly 1 to the End Pieces left and right 2 Use Bolts 5 to attach Hand tighten only See Figure 2 Round Back Assembly 1 Bolt 8 Figure 2 3 With the assistance of another person carefully tum the Bench upside down and attach the Support Bracket 6 with the Self Tap Screws 7 in the two center predrilled holes Screw into the second wood slat counting from the back of the seat Use Bolts Nuts and Washers 5 to secure the ends of the Support Bracket to the End Pieces 2 left and right See Figure 3 Bolt Nut amp Washer 5 Support Bracket 6 Self Tap underneath Screw 7 Bolt Nut amp Washer 5 Figure 3 Note Use a small Carpenter s Square to adjust the angle between the End Pieces 2L amp R and Slats so you can maintain the 90 angle SKU 92647 For technical questions please call 1 800 444 3353 Page 4 4 Tighten all hardware at this time maintain the 90 angle while tightening all hardware Ch
5. t of the assembly and do not overtighten the bolts Serious damage can occur Do not stand on this Bench Use only for intended purpose The Park Bench is made for children Children need to be supervised Injury could occur if Park Bench is overloaded Use caution 13 STORE IDLE EQUIPMENT When not in use products must be stored in a dry location to inhibit damage from moisture and salt air 14 TIPPING HAZARD Do not jump or climb on the Bench Do not allow anyone to sit on the back of the Bench 15 REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Use of any other parts will void the warranty Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator UNPACKING When unpacking check to make sure all parts shown on the Parts List page 5 are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible ASSEMBLY INSTRUCTIONS We suggest you assemble the unit on a soft surface to avoid damage to the finish ASSEMBLY OF BENCH PLACING SLATS Attach the five Seat Slats 3 in the channel of the End Pieces 2 as shown Note The Round Slat is to be anchored in the front o
Download Pdf Manuals
Related Search