Home

BREVILLE BKC600XL User's Manual

1. We recommend removing the Water Filter if you choose not to replace the Charcoal Filter every 2 months as the filter may clog and affect the smell and taste of the water he One time priming process Priming fills the internal tank with water and cleanses the brewing system You cannot use your Brewer until it has been primed for its first use If the Brewer has been exposed to temperatures below freezing allow the Brewer at least two hours to reach room temperature before priming A frozen or extremely cold Brewer will not prime properly and can cause damage 1 Unwrap the power cord and plug the Brewer into a grounded outlet 2 Place a 12 oz mug on the Drip Tray Plate The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs 3 Fill the Water Tank with water until it is approximately 1 inch below the top edge The Water Tank can be filled in two ways a Remove the Water Tank Lid and pour water directly into the Water Tank while it is still attached to the Brewer then replace the Lid b Remove the Water Tank Lid then gripping the handle located on the left side of the Water Tank lift upwards Fill with water Place the Water Tank back onto the Brewer and replace the Lid BR9013 BKC600XL TB AMEND qxp 11 10 07 zeke Page 9 4 Press and release the Power Switch located on the lower back right side of the Brewer The Power Switch is spring loaded and will return to
2. Mineral content in water varies from place to place Depending on the mineral content of the water in your area calcium deposits or scale may build up in your Brewer Scale is non toxic but left unattended it can hinder the Brewer s performance Descaling your Brewer helps maintain the heating element and other internal parts of the Brewer that come in contact with water The Brewer should be descaled every 3 6 months to ensure optimal performance It is possible for calcium deposits to build up faster making it necessary to descale more often This Brewer is equipped with sensors to detect when scale buildup is interfering with the performance of the Brewer When this is detected the LCD screen will indicate DESCALE Feb READY TO BREW ON OFF TIME ACTIVE 23 BR9013 BKC600XL TB AMEND qxp 11 10 07 zeke Page 24 Care and cleaning continued 11 Repeat the cleansing brew process until the The Brewer will continue to operate even when h hie i Water Tank is empty pouring the contents of the Possil the LCD screen indicates DESCALE cup into the sink after each cycle You may need to perform additional rinse cycles if you notice Brewel any residual taste Remember to raise and lower the Safety Locking Arm between each cycle so However if you do not descale the Brewer soon after it is displayed continued scale build up could the control panel buttons illuminate damage the Brewer If this
3. Once the appropriate minute is reached press the OK button The LCD screen will display OFF TIME indicating that the time you wish the Brewer to automatically turn off is ready to be set lt Setting the OFF TIME i Follow the instructions ii to iv for Setting the ON TIME i Once the appropriate time is reached press the OK button The LCD screen will return to the menu programming options To exit the menu programming options press the MENU button Alternatively press the button to reach EXIT MENU and press the OK button The LCD screen will return to the main screen and indicate whether you have activated the ON OFF TIME feature Geo READY TO BREW ON OFF TIME ACTIVE If you w OFF TIN Switch Brewer the wate to brew Setting This featul 2 hours fr 1 Press option blinkir Press 3 Press ress two 0 a AL scr Bre the scr opt BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 19 b AUTO OFF will be ACTIVE and the LCD 1 press If you want to brew outside the ON TIME and screen will display 2 hr indicating the Brewer k OFF TIME selected press and release the Power will automatically tum off after 2 hours Press to Switch on the lower back right side of the the OK button The LCD screen will return to Brewer to restore power You will have to wait fo
4. liquids Wipe the housing with a soft damp 4 Store cloth then dry thoroughly My K of the Do not use abrasive scouring pads or cleaners when cleaning the housing as they may scratch Cleanin the surface 3 Wash both parts in warm soapy water with a 1 Wipe soft cloth then rinse and dry thoroughly The then c K Cup Holder and Funnel are also top shelf into th dishwasher safe 2 Wash 2 The Drip Tray and Drip Tray Plate can accumulate soft cl up to 12 oz of overflow The water level indicator The K Cup Holder houses a needle in the inside dry th visible through the Drip Tray Plate will pop up base Should a clog arise due to coffee grinds it remai when this occurs The Drip Tray and Drip Tray can be cleaned using a paper clip or similar tool the di Plate should then be removed emptied and Insert the paper clip into the Needle to loosen the cleaned To remove the Drip Tray assembly slide clog and push it out To avoid risk of injury do not Rinse th it toward you keeping it level at all times to put your fingers in the K Cup Holder el avoid spilling Wash both parts in warm soapy water with a soft cloth then rinse and dry thoroughly The Drip Tray and Drip Tray Plate are also top shelf dishwasher safe 4 After cleaning place the Funnel back onto the K Cup Holder remain supply i Cleaning the K Cup Holder 5 Place the assembled K Cup Holder back into Regular cleaning of the K Cup Holder is the Brewin
5. OK button The LCD screen will indicate the default brew size 7 25 oz BREW SIZE we 3 Press bi Select fr a small oz servi 4 Once buttor progre 5 To exi MENL to rea The L and in BR9013 BKC600XL TB AMEND qxp 11 10 07 zeke Page 21 vill return 3 Press the button to go up in size or the button to go down in size press ne Select from a stronger small cup 5 25 oz serving ess the a small mug 7 25 oz serving a large mug 9 25 to the oz serving or a travel mug 11 25 oz serving over W 4 Once the brew size is selected press the OK button The LCD screen will return to the menu programming options 5 To exit the menu programming options press the MENU button Alternatively press the button to reach EXIT MENU and press the OK button The LCD screen will return to the main screen ough and indicate the brew size selected t often gramming ith P ZE vill BR9013 BKC600XL TB AMEND qxp 11 10 07 Zick Page 22 Care and cleaning Before cleaning ensure the Brewer has been turned 2 Disas off Switch off at the wall outlet unplug the power the Lit cord and allow the machine to cool direct Holdel Cleaning the brewer housing 3 Wash Regular cleaning of the Brewer s housing and soapy external components is recommended thorot 1 Never immerse the Brewer in water or other shelf
6. the saning marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of nbling or the appliance 2 the cord should be arranged so that it will not drape over the countertop or tabletop where it ypliance can be pulled on by children or tripped over unintentionally and 3 the extension cord must include a 3 prong grounding plug actions ord plug SAVE THESE INSTRUCTIONS 3 hole n FOR HOUSEHOLD USE ONLY the risk tlet it ion to TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT REMOVE THE BASE PANEL 3 prong A NO USER SERVICEABLE PARTS ARE INSIDE REPAIR SHOULD BE DONE ONLY BY AUTHORIZED PERSONNEL ONLY BR9013 BKC600XL IB AMEND qxp 11 10 07 zeke Page 6 Water tank lid A F Drip tray plate K Brewing chamber head P MyK C B Water tank G Drip tray level indicator L Brewing chamber Q MyKC C Upper filter holder H Drip tray M LCD screen R MyK C D Replaceable charcoal filter K Cup holder N Control panel S MyK C E Lower filter holder J Safety locking arm 0 MyK Cup K Cup holder storage T Power ler storage BR9013 BKC600XL IB AMEND qxp 11 10 07 Zick Page 7 P My K Cup measuring scoop Q MyK Cup lid R My K Cup filter basket S MyK Cup holder T Power Switch To order replacement Charcoal Filters call Breville Customer Service on 1 866 BREVILLE or visit www breville com BR9013 BKC600XL IB AMEND qxp 11 10 07 zeke Pag
7. its original position The Water Tank LED will illuminate The LCD screen will illuminate and indicate PRIME The BREW button will illuminate and flash PRIME 206 pS If the Water Tank is empty or not in place on the Brewer the Water Tank LED s will flash and the LCD screen will indicate REFILL TANK None of the control panel buttons will be active until water is added to the Water Tank AK Cup should not be used for the one time priming process Press the BREW button The Brewer will automatically fill with water and make a vibrating sound This is normal The Brewer will then cease to vibrate and begin heating the water This entire process will take approximately 4 minutes The LCD screen will indicate HEATING during this period The Brewer will take about 4 minutes to heat up during the priming process BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 10 Operating your Breville Gourmet Single Cup Brewer continued 9 Once the water is heated the LCD screen will no longer indicate HEATING The BREW button will illuminate and flash for up to 60 seconds 10 Press the BREW button This will start a cleansing brew which will complete the priming sequence The LCD screen will no longer indicate PRIMING Hot water will flow into your mug When the flow stops discard the hot water READY TO BREW 11 The LCD screen will i
8. occurs DESCALE will 12 The machine is now ready for use begin to flash alerting you to the potential damage to the Brewer if you do not descale immediately If the LCD screen continues to indicate Promptly follow these steps each time the LCD DESCALE after completing the process repeat Brewe screen indicates DESCALE to ensure the Brewer the process above functions optimally 1 Empty the Water Tank 2 Pour 60 oz of vinegar into the Water Tank filling to just below the top edge of the clear viewing area Storage 3 Place a 12 oz or larger ceramic cup do not use Before cleaning or moving the Brewer to a different a plastic cup on the Drip Tray The Drip Tray and location ensure the Brewer has been turned off Drip Tray Plate can be removed to accomodate Switch off at the wall outlet unplug the power cord taller mugs and travel mugs and allow the machine to cool The Water Tank 4 Select the largest brew size 11 25 oz serving should be emptied and dried thoroughly by pressing the button on the control panel Store your Brewer in its upright position to avoid 5 Runa cleansing brew without a K Cup refer to water leakage from the inner tank Brewing Hot Water page 15 Pour the contents Store your Brewer in a frost free environment of the cup into the sink Storing the Brewer in a cold environment runs the 6 Repeat the cleansing brew process until the risk of water freezing inside the Brewer and
9. BR9013 BKC600XL TB AMEND qxp 11 10 07 mt 3 Page al l PRINTED ON Breville RECYCLED PAPER Breville is a registered trademark of Breville Pty Ltd Breville Customer Service Center US Customers bed 19400 S Western Ave Torrance CA 90501 1119 Service Center 1 866 BREVILLE Email askus brevilleUSA com www breville com Canada Customers Bx Anglo Canadian 2555 Avenue Aviation Pointe Claire Montr al Qu bec HOP 222 Service Center 1 866 BREVILLE Fax 514 683 5554 Email askus breville ca www breville com Copyright Breville Pty Ltd 2007 Keurig Keurig Brewed Brewing Excellence One Cup at a Time and K Cups are trademarks or registered trademarks of Keurig Incorporated Covered by U S Patents Numbers 7 165 488 D513572 and 5 840 189 and other U S and foreign patents pending Due to continual improvements in design or otherwise the product you purchase may differ slightly from the one illustrated in this booklet Model BKC600XL Issue 2 07 Packaging Code NA Model BI FILENA BREVIL A5 Inst BR9013 BKC600XL TB AMEND qxp 11 10 07 Page 1 Gourmet Single Cup Brewer Breville Model BKC600XL FILENAME BKC600XL Book IB AMEND qxp ARTWORK SCALE 100 BREVILLE gt BR9013 gt IW GW GC PRINTED HERE AT 100 A5 Instruction Booklet PMS 8403C and BLACK BLACK PMS 8403C BR9013 BKC600XT TB AMEND qxp 11 10 07 Zick Page 2 Contents Page Breville recommends saf
10. Coffee Water Tank is empty pouring the contents of the causing damage If your Brewer has been stored in ar wat cup into the sink after each cycle Remember an environment below freezing ensure to let it to raise and lower the Safety Locking Arm warm to room temperature for at least 2 hours between each cycle so the control panel before using buttons illuminate When preparing to use the Brewer after storage 7 Let the Brewer stand for at least 4 hours while we recommend rinsing the Water Tank with fresh still on water and running three cleansing brews without There a 8 Rinse the Water Tank thoroughly and fill with a K Cup refer to Brewing Hot Water page 15 from 13 fresh water on K Ci 9 Place a 12 oz or larger ceramic cup do not use em www br a plastic cup on the Drip Tray 10 Run a cleansing brew without a K Cup refer to Sx Brewing Hot Water page 15 Pour the contents of the cup into the sink 24 BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 25 Troubleshooting the its of the Possible problem Easy solution lay need notice Brewer will not switch on Plug the Brewer into an independent outlet ind lower Check that the Brewer is plugged in securely ycle so Plug into a different outlet e Reset circuit breaker if necessary Make sure that the Power Switch has been turned on The Water Tank should be illuminated The BREW button and buttons should be illumi
11. Safety Locking Arm The Brewing Chamber will open toward you 5 Select a K Cup 6 Place in the lid or lt There al K Cup Chambe Cup ut your K Cup 7 Lower Brewil When indica buttor illumir BR9013 BKC600XL_IB AMEND qxp 11 10 07 zeke Page 11 6 Place the K Cup in the K Cup Holder located a The LCD screen will indicate the default brew e in the Brewing Chamber Do not remove the foil size 7 25 0z To choose a different size D Open lid or puncture the K Cup press the button to go up in size or the nd button to go down in size ately The W Select from a stronger small cup 5 25 oz serving mplete a small mug 7 25 oz serving a large mug 9 25 brew oz serving or a travel mug 11 25 oz serving The small mug 7 25 oz serving is the default brew size To program your favorite brew size refer to Setting the BREW SIZE feature page 20 ie ess page the ted b Once the brew size is selected press the BREW BREW A z rae 6 Button The BREW button will stop flashing the ae 9 a lt 5 2 k es IO e and buttons will no longer be lit The ae a selected brew size a gt K Cup Holder To avoid risk of injury do not as put your fingers in the Brewing Chamber or zonds K Cup Holder cidental open wering T Lower the Safety Locking Arm to close he Brewing Chamber Head over the K Cup Holder When clo
12. accidental activation To re activate the brew sequence open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely Do not remove the Water Tank during the brewing process Purging the brewer If the Brewer has not been used for more than one week you should renew the water from the inner tank by purging the brewer 1 If there is water in the Water Tank remove the Water Tank Lid then gripping the handle located on the left side of the Water Tank lift upwards Discard the water rinse and refill with bottled or filtered water Place the Water Tank back onto the Brewer and replace the Lid 2 If there is no water in the Water Tank refill with water Place the Water Tank back onto the Brewer and replace the Lid 3 Ensure the Brewer is turned on Raise and lower the Safety Locking Arm on the Brewer without inserting a K Cup 4 The LCD screen will indicate READY TO BREW and the BREW button will illuminate and flash The LCD screen will indicate the default brew size 7 25 oz serving unless programmed otherwise Select the largest brew size 11 25 oz serving by pressing the button on the control panel Place a 12 oz mug on the Drip Tray Plate The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs Press the BREW button Hot water will flow into your mug When the flow stops discard the hot water Repeat this proce
13. arcoal Filter for 5 minutes then rinse for 30 seconds It is normal to see a grey residue after soaking the filter 6 Wash the Lower Filter Holder ensuring the stainless steel mesh is free of residue 7 Insert the Charcoal Filter into the Upper Filter Holder then attach the Lower Filter Holder so it locks into place cS ce LF 8 Set the date dial on the Upper Filter Holder 2 months ahead This will remind you when the Charcoal Filter will need to be replaced 9 Place the assembled Filter Holder into the Water Tank aligning so the date dial is visible from outside the Tank Push down hard on the assembled Filter Holder until it snaps into place 10 Your Brewer is ready for the one time priming process Replace 60 tank To order Breville visit ww We reco choose 2 month smell ar One tim Priming fil the brewir it has bee rae Br elow fr hours to A frozen properly 1 Unwre into a 2 Place drip tr accon 3 Fill the appro The W a nd Jer and p the nen rinse y residue he Filter ler so it der hen the je Water from e to place Replace the Charcoal Filter every 2 months or 60 tank refills more if you have hard water To order replacement Charcoal Filters call Breville Customer Service on 1 866 BREVILLE or visit www breville com
14. e selected brew size 0 13 Raise the Safety Locking Arm remove the assembled My K Cup Holder Use caution as the My K Cup Holder will be hot oe 14 Disassemble the My K Cup Holder by removing Stoppin the Lid from the Holder in a counter clockwise To stop br direction Remove the Filter Basket from the and releas Holder discard the grounds and rinse out the Brewer to Filter Basket and Holder hot cocoa 15 Enjoy your first cup of gourmet coffee tea or and the LE hot cocoa longer be ve A ON OFF T panel butt back on If the BREW button is not pressed in 60 You maj seconds the LCD screen will indicate OPEN your ne HEAD and the BREW button will be disabled to recomm prevent accidental activation To re activate the Brewing brew sequence open the Brewing Chamber then dis Head by raising and lowering the Safety Locking the brev Arm completely ma 14 however reWInd 60 remove Cup id risk rm or wing dicate for the 15 sound e tion as removing ckwise the it the a OF The My K Cup accessory is designed for ground coffee only Do not a Use a K Cup or coffee pod in the My K Cup Filter Basket b Use the My K Cup Filter Basket with the K Cup Holder After brewing with the My K Cup accessory the K Cup Holder must be inserted into the Brewing Chamber in order to brew a K Cup To rep
15. e 8 Operating your Breville Gourmet Single Cup Brewer Installing the water filter For the best tasting gourmet coffee tea or hot cocoa Breville recommends using bottled or filtered water The Water Filter provided with the Brewer can significantly reduce substances that affect the smell and taste of water such as free chlorine certain pesticides and organic impurities as well as traces of heavy metals The Water Filter can be removed from the Brewer If you choose to install the Water Filter it is recommended to replace the Charcoal Filter every 2 months or 60 tank refills more often if you have hard water We recommend removing the Water Filter if using filtered water or if you choose not to replace the Charcoal Filter every 2 months as the filter may clog and affect the smell and taste of the water If you choose not to install the Water Filter you are ready to start the One time Priming Process page 9 Follow these steps each time you install a new Charcoal Filter to ensure it filters optimally 1 Remove the Water Tank from the Brewer by gripping the handle located on the left side of the Water Tank then lift upwards 2 Remove the Water Tank Lid 3 Rinse the Water Tank with fresh water and replace back onto the Brewer 4 Remove the Upper and Lower Filter Holder and Charcoal Filter from the polybag Unwrap the Charcoal Filter from its protective plastic 5 Soak the Ch
16. e Lid from the Holder in a counter clockwise direction Remove the Filter Basket from the Holder 6 Wash the My K Cup Lid Filter Basket and Holder in warm soapy water prior to first use Rinse and dry thoroughly 7 Insert the Filter Basket into the Holder 8 Use tr Filter coffee tables on the tables the an prefer more the gi there upper to sea 1 level s We reco serving Or if yo cup 5 2 you gr 1 Start Pres 2 Expe brew 3 Avoic COUl poor 9 Raise chaml 10 Place Brewil a Rel Ch the On b Ins the the the BR9013 BKC600XT TB AMEND qxp 11 10 07 Zick Page 13 8 Use the My K Cup Measuring Scoop to fill the EN Filter Basket with 1 level scoop maximum of coffee 1 level scoop is equivalent to 2 led jate tablespoons Alternatively there are line markings on the inside of the Filter Basket that indicate 1 amber i ocking tablespoon and 2 tablespoons so you can adjust the amount of coffee to your personal preference Do not fill the Filter Basket with more than one level scoop of coffee or tamp the grinds Ensure the coffee remains loose and te The there are no coffee grinds remaining on the oved to upper rim of the Filter Basket Screw on the Lid 5 seal There are two sharp needles used to puncture on top of 1 level scoop 2 tablespoons the K Cup and My K Cup Holder One in ton the We recommended this for the small mug 7 25 oz t
17. ety first 4 Know your Breville Gourmet Single Cup Brewer 6 Operating your Breville Gourmet Single Cup Brewer 8 Installing the water filter 8 One time priming process 9 Brewing a K Cup 10 Brewing with the My K Cup 12 Stopping the brew process 15 Brewing hot water 15 Refilling the water tank 15 Purging the brewer 16 Menu and programming options 17 Setting the CLOCK SET feature 17 ae Setting the ON OFF TIME feature 17 on the Setting the AUTO OFF feature 19 Setting the BREW TEMP feature 20 Setting the BREW SIZE feature 20 Care and cleaning 22 Cleaning the brewer housing 22 Cleaning the K Cup holder 22 oul Bi Cleaning the My K Cup 22 ee Cleaning the water tank and lid 23 A Cleaning the water filter 23 Descaling the brewer 23 Storade 24 Bre Trouble shooting 25 For mo One year limited warranty 27 orderin French F1 1 866 oO D A qxp 11 10 07 21 BR9013 BKC600XL_IB_AMEND BR9013 BKC600XL TB AMEND qxp 11 10 07 zeke Page 4 Breville recommends safety first IMPORTANT SAFEGUARDS We at Breville are very safety conscious We design and manufacture consumer products with the safety of you our valued customer foremost in mind In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions READ ALL INSTRUCTIONS AND SAVE THESE FOR FUTURE REFERENCE This appliance is for household use only Do
18. g Chamber aligning the arrow Cleanin recommended on the K Cup Holder with the arrow W in Regular cl 1 Raise the Safety Locking Arm and remove the the Brewing Chamber Use caution when doing We sugge K Cup Holder from the Brewing Chamber refer to this as there is a sharp needle on the underside replaced e Brewing with the My K Cup Accessory page 12 i a Brewing Chamber Head that punctures the ee 2 Disassemble the K Cup Holder buy pulling a Lower downwards on the Funnel located at the base of Cleaning the My K Cup accessory Discar the Holder Regular cleaning of the My K Cup accessory is 2 Wash recommended soapy 1 Remove the assembled My K Cup Holder from thoro the Brewer by raising the Safety Locking Arm Use dishw 2 caution as the My K Cup Holder will be hot BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 23 vith a The shelf inside ids a r tool en the do not ito the ck into N a Y in n doing iderside tures the ry ory is Jer from Arm Use gt hot 2 Disassemble the My K Cup Holder by removing the Lid from the Holder in a counter clockwise direction Remove the Filter Basket from the Holder discard the grounds 3 Wash the Lid Filter Basket and Holder in warm soapy water with a soft cloth then rinse and dry thoroughly All parts K Cup Holder are also top shelf dishwasher safe 4 Store the assembled My K Cup Holder in the My K Cup Stora
19. ge compartment located on top of the Brewer Cleaning the water tank and lid 1 Wipe the Water Tank Lid with a soft damp cloth then dry thoroughly The Lid should not be put into the dishwasher 2 Wash the Water Tank in warm soapy water with a soft cloth then rinse and dry thoroughly Do not dry the inside of the Tank with a cloth as lint may remain The Water Tank should not be put into the dishwasher Rinse the Water Tank thoroughly after cleaning to ensure that no cleaners or cleaning solutions remain as they may contaminate the water supply in the Brewer Cleaning the water filter Regular cleaning of the Water Filter is recommended We suggest doing this when the Charcoal Filter is replaced every 2 months or 60 tank refills 1 Disassemble the Water Filter by removing the Lower Filter Holder from the Upper Filter Holder Discard the Charcoal Filter 2 Wash the Upper and Lower Filter Holder in warm soapy water with a soft cloth then rinse and dry thoroughly Both parts are also top shelf dishwasher safe Replace the Charcoal Filter every 2 months or 60 tank refills more if you have hard water To order replacement Charcoal Filters call Breville Customer Service on 1 866 BREVILLE or visit www breville com We recommend removing the Water Filter if you choose not to replace the Charcoal Filter every 2 months as the filter may clog and affect the smell and taste of the water Descaling the brewer
20. he base of the K Cup Holder the other on the eS SOY seria underside of the Brewing Chamber Head by To avoid risk of injury use caution when inserting sinters Or if you like a stronger brew select the small or removing the K Cup K Cup Holder or My aket cup 5 25 oz serving K Cup Holder MM and 1 Start with a coarser grind similar to a French t use Press grind a 11 Lower the Safety Locking Arm to close the 2 Experiment with grinds similar to drip Brewing Chamber Head over the My K Cup brewing grinds Holder When closed completely the LCD screen 3 Avoid a fine espresso grind setting that will indicate READY TO BREW The and could clog the Filter Basket or result in buttons will illuminate and the BREW button will poor extraction illuminate and flash for up to 60 seconds 9 Raise the Safety Locking Arm The Brewing chamber will open toward you D 10 Place the assembled My K Cup Holder into the Brewing Chamber To do this a Remove the K Cup Holder from the Brewing Chamber 10a Store the K Cup Holder in the My K Cup Storage compartment located on top of the Brewer Insert the assembled My K Cup Holder into the Brewing Chamber 10b ensuring to align the arrow on the My K Cup Lid with the arrow W in the Brewing Chamber READY TO BREW BR9013 BKC600XL_IB AMEND qxp 11 10 07 zeke Page 14 Operating your Breville Gourmet Sing
21. lace the K Cup Holder raise the Safety Locking Arm and remove the My K Cup Holder Insert K Cup Holder into the Brewing Chamber aligning the arrow on the K Cup Holder with the arrow Win the Brewing Chamber Use caution when doing this as there is a sharp needle on the underside of the Brewing Chamber Head that punctures the K Cup Stopping the brew process To stop brewing after the process has started press and release the Power Switch on the right side of the Brewer to the OFF status The flow of coffee tea or hot cocoa will stop the heating element will shut off and the LED illuminating the Water Tank will no longer be lit The LCD screen will indicate the time ON OFF TIME and AUTO OFF None of the control panel buttons will be active until the Brewer is turned back on You may get less coffee tea or hot cocoa during your next brew After a terminated brew we recommend that you follow the instructions for Brewing hot water page 15 Your next brew will then dispense the correct volume according to the brew size you have selected BR9013 BKC600XL IB AMEND qxp 11 10 07 zeke Page 15 Brewing hot water The Brewer is able to dispense a cup of hot water for making hot chocolate in a packet for use in cooking for making soups etc Follow the instructions Brewing a K Cup page 10 without inserting a K Cup After brewing a hot cocoa K Cup or stopping the brew
22. le Cup Brewer continued a The LCD screen will indicate the default brew 12 The LCD screen will indicate BREWING however size 7 25 0z To choose a different size press there may be a short pause before the brewing TheMy the to go up in size or the button to go process begins The process lasts about 60 ground down in size seconds and ends with a burst of air to remove a Use i all liquid from the My K Cup Holder K Cu Select from a stronger small cup 5 25 oz serving b Use a small mug 7 25 oz serving a large mug 9 25 There is extremely hot water in the My K Cup K Cu oz serving or a travel mug 11 25 oz serving Holder during the brewing process To avoid risk After bre The small mug 7 25 oz serving is the default of injury do not raise the Safety Locking Arm or the K Ct brew size To program your favorite brew size open the Brewing Chamber during the brewing Brewing refer to Setting the BREW SIZE feature page 20 process To repla Following the brew the LCD screen will indicate Locking HEATING as the Brewer heats the water for the Insert K next brew cycle This process lasts about 15 aligning b Once the brew size is selected press the BREW seconds The pump will make a vibrating sound with the Button The BREW button will stop flashing the This is normal Meca and buttons will no longer be lit The LCD screen will indicate BREWING and the iee
23. nated epeat Brewer will not brew After placing the K Cup in the K Cup Holder or the My K Cup Holder into the Brewing Chamber ensure the Safety Locking Arm is pushed down securely The LCD screen should indicate READY TO BREW The and buttons should illuminate and the BREW button should illuminate and flash for up to 60 seconds If the LCD screen indicates REFILL TANK add water to the Water Tank or ifferent make sure the Water Tank is attached correctly to the Brewer page 15 off e If the LCD screen indicates REFILL TANK even after refilling contact erc Customer Service on 1 866 BREVILLE 1 866 273 8455 nk If the BREW button is not pressed in 60 seconds the LCD screen will indicate OPEN HEAD and the BREW button will be disabled to prevent avoid accidental activation To re activate the brew sequence open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely ent The Exit Needle may be clogged refer Cleaning the K Cup Holder runs the page 22 nd Coffee is too weak Reduce the brew size selection for a stronger tasting cup of coffee stored m or watery refer to Setting the BREW SIZE feature page 20 letit Try an Extra Bold K Cup They have 30 more ground coffee in each Mi K Cup portion pack forage th fresh without There are over 150 varieties of Keurig K Cups ge 15 from 13 g
24. ndicate HEATING as the Brewer heats the water for the next brew cycle Once the water is heated the LCD screen may indicate REFILL TANK REFILL TANK OO 12 Fill the Water Tank with water until it is approximately 1 inch below the top edge 13 The LCD screen will indicate OPEN HEAD Open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely The LCD screen will indicate READY TO BREW 14 The one time priming process is now complete and you are ready for your first K Cup brew page 10 or My K Cup brew page 12 Brewing a K Cup 1 Follow the instructions Installing the Water Filter page 8 and the One time Priming Process page 9 The Brewer should be turned on and the Water Tank should be filled and illuminated 2 The LCD screen will indicate READY TO BREW The and buttons will illuminate and the BREW button will illuminate and flash for up to 60 seconds If the BREW button is not pressed in 60 seconds the LCD screen will indicate OPEN HEAD and the BREW button will be disabled to prevent accidental activation To re activate the brew sequence open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely 3 Place a cup or mug on the Drip Tray Plate The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs 4 Raise the
25. not use this appliance for anything other than its intended use Do not use in moving vehicles or boats Do not use outdoors To protect against fire electrical shock and injury to persons do not immerse the appliance cord or plug in water or any other liquid Do not leave the appliance unattended when in use Close supervision is necessary when the appliance is used by or near children Always use the appliance on a dry level surface Do not place this appliance on or near a hot gas or electric burner or where it could touch a heated oven Do not touch hot surfaces Use handles and knobs where available Do not let the cord hang over the edge of a table or counter touch hot surfaces or become knotted The use of accessory attachments not recommended by Breville may cause a risk of injury to persons fire or electric shock Do not overfill the Water Tank Always keep the Water Tank Lid on the Water Tank unless you are refilling it Use only water in this appliance Do not put any other liquids or foods in the Water Tank except as instructed in Care and Cleaning page 23 There are two sharp needles that puncture the K Cup One on the underside of the Brewing Ds Chamber Head and the other in the base of the K Cup Holder To avoid risk of injury do not put your fingers in the Brewing Chamber or K Cup Holder There is extremely hot water in the K Cup Holder during the brewing process To avoid risk of injury d
26. o not raise the Safety Locking Arm or open the Brewing Chamber during the brewing process To turn off the appliance press and release the Power Switch on the lower back right side of the Brewer to the OFF status and then remove the plug from the wall outlet Always switch the appliance to the OFF status and then remove the plug from the wall outlet when the appliance is not being used and before cleaning Allow the appliance to cool before reassembling or removing parts and before cleaning the appliance Strictly follow the Care and Cleaning instructions page 22 This appliance is equipped with a power cord having a grounding wire with a grounding plug The appliance must be grounded using a 3 hole properly grounded outlet In the event of an electrical short circuit grounding reduces the risk of electrical shock If the outlet is a standard 2 prong wall outlet it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet Do not the thirc use an i Consult instructi doubt e properly Regularl actual a if damac malfunc applianc 1 866 E adjustm For any Breville OP Your Brevi or propert children tc marked el the applia can be pu grounding BR9013 BKC600XL IB AMEND qxp 11 10 07 Zick Page 5 Do not under any circumstances cut or remove the third ground prong from the power cord or Your Breville appliance comes with the unique
27. of gourmet coffee tea or hot cocoal 11 The LCD screen will indicate READY TO BREW indicating that the next K Cup can be inserted for the next brew cycle Brewing with the My K Cup Accessory The Breville Gourmet Single Cup Brewer comes with a My K Cup accessory The dishwasher safe reusable My K Cup allows you to use your own grind of coffee so you can adjust the amount and type of coffee to suit your tastes Along with the included measuring scoop this accessory conveniently stores in the easy open compartment on top of the brewer 1 Follow the instructions Installing the Water Filter page 8 and the One time Priming Process page 9 The Brewer should be turned on and the Water Tank should be filled and illuminated 2 The LCD screen will indicate READY TO BREW If the BREW button is not pressed in 60 seconds the LCD screen will indicate OPEN HEAD and the BREW button will be disabled to prevent accidental activation To re activate the brew sequence open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely 3 Place a cup or mug on the Drip Tray Plate The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs 4 Open the storage compartment located on top of the Brewer by pressing the finger indent on the right side Remove the My K Cup accessory 5 Disassemble the My K Cup accessory by removing th
28. ourmet partners For more information on K Cups or K Cup ordering call Breville Customer Service on 1 866 BREVILLE or visit www breville com BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 26 Troubleshooting continued One yea Possible problem Easy solution Brevlle defects thi Brewer dispenses a The Exit Needle may be clogged refer to Cleaning the K Cup Holder workmans partial cup page 22 date of ori The Water Tank may have been removed during brewing Replace the does not c Water Tank and perform a cleansing brew without a K Cup commerci refer to Brewing Hot Water page 15 the printec e If the LCD screen indicates DESCALE follow the instructions Descaling warranty f your Brewer page 23 basket bl If you have repeated the descale procedure on your Brewer two times disclaims and the message is still displayed contact Customer Service on for incider 1 866 BREVILLE 1 866 273 8455 Some stat es or limitatic The time is not displayed The time will not be displayed on the LCD screen unless you have set it the forego on the LCD screen To set the clock follow the instructions Setting the CLOCK SET feature page 17 ne i ANY WARF e If power is interrupted to the Brewer you will need to set the clock again ITH RESI Brewer shuts off or turns Check to make sure that the ON OFF TIME and or the AUTO OFF EO on automatically features have not been set To do this press
29. process mid cycle we recommend running a hot water brew cycle Refilling the water tank The LCD screen will indicate REFILL TANK when the water level in the Water Tank is low or if the Water Tank has been removed 1 Fill the Water Tank with water until it is approximately 1 inch below the top edge The Water Tank can be filled in two ways a Remove the Water Tank Lid and pour water directly into the Water Tank while it is still attached to the Brewer then replace the Lid b Remove the Water Tank Lid then gripping the handle located on the left side of the Water Tank lift upwards Fill with water Place the Water Tank back onto the Brewer and replace the Lid 2 The LCD screen will indicate either a OPEN HEAD Raise and lower the Safety Locking Arm completely b HEATING as the Brewer heats the water for the next brew cycle This process lasts about 15 seconds The pump will make a vibrating sound This is normal 3 Once the Safety Locking Arm is opened and lowered or the water is heated the LCD screen will indicate READY TO BREW indicating the brew cycle can begin The and buttons will illuminate and the BREW button will illuminate and flash for up to 60 seconds BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 16 If the BREW button is not pressed in 60 seconds the LCD screen will indicate OPEN HEAD and the BREW button will be disabled to prevent
30. r the menu programming options the the water to heat up before the Brewer is ready 5 To exit the menu programming options press the to brew MENU button Alternatively press the button ad press Note to reach EXIT MENU and press the OK button The LCD screen will return to the main screen ispla ane and indicate whether you have activated the ready to Setting the AUTO OFF Feature AUTO OFF feature This feature automatically turns the Brewer off after 2 hours from the last brew tting the 1 Press the MENU button The programming options will appear on the LCD screen with a blinking indicator on CLOCK SET READY TO BREW press AUTO OFF ACTIVE return t 2 Press the button to reach AUTO OFF 3 Press the OK button pres 4 Press the or button to see the button two options button screen j the E h r mw OO S AUTO OFF INACTIVE e AUTO OFF ACTIVE CD C OO LOO O O a AUTO OFF will be INACTIVE and the LCD screen will display indicating that the Brewer will not turn off automatically Press the OK button to select this option The LCD screen will return to the menu programming options BR9013 BKC600XT TB AMEND qxp 11 10 07 zeke Page 20 Menu and Programming Options continued Setting the BREW TEMP feature The Brewer brews coffee at a preset tempe
31. rature of 192 F You can adjust this temperature down by 5 F if you prefer a cooler cup of coffee tea or hot cocoa 1 4 Press the MENU button The programming options will appear on the LCD screen with a blinking indicator on CLOCK SET Press the button to reach BREW TEMP Press the OK button The LCD screen will indicate the default brew temperature 192 F or the pre programmed brew temperature BREW TEMP Press the or button to reach the appropriate brew temperature The temperature can only be set between 187 F and 192 F The Brewer will remain at the selected temperature for subsequent brews 5 Press the OK button The LCD screen will return to the menu programming options 6 To exit the menu programming options press the MENU button Alternatively press the button to reach EXIT MENU and press the OK button The LCD screen will return to the main screen When using the Brewer at high altitudes over 5 000 feet if boiling occurs use the BREW TEMP feature to lower the temperature Setting the BREW SIZE feature This feature allows you to avoid scrolling through brew sizes if a particular size is chosen most often 1 Press the MENU button The menu programming options will appear on the LCD screen with a blinking indicator on CLOCK SET 2 Press the button to reach BREW SIZE Press the
32. sed completely the LCD screen will Note indicate READY TO BREW The and buttons will illuminate and the BREW button will illuminate and flash for up to 60 seconds te Th ns S oO ing READY TO BREW If the BREW button is not pressed in 60 seconds the LCD screen will indicate OPEN HEAD and the BREW button will be disabled to prevent accidental activation To re activate the brew sequence open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely Note BR9013 BKC600XL TB AMEND qxp 11 10 07 zeke Page 12 Operating your Breville Gourmet Single Cup Brewer continued 8 The LCD screen will indicate BREWING however there may be a short pause before the brewing process begins The process lasts about 60 seconds and ends with a burst of air to remove all liquid from the K Cup There is extremely hot water in the K Cup Holder during the brewing process To avoid risk of injury do not raise the Safety Locking Arm or open the Brewing Chamber during the brewing process Following the brew the LCD screen will indicate HEATING as the Brewer heats the water for the next brew cycle This process lasts about 15 seconds The pump will make a vibrating sound This is normal 9 Raise the Safety Locking Arm remove and dispose of the used K Cup Use caution as the K Cup will be hot 10 Enjoy your first cup
33. ses so the foregoing disclaimer may not apply to you ANY WARRANTY OF MERCHANTABILITY OR FITNESS WITH RESPECT TO THIS PRODUCT IS ALSO LIMITED TO THE ONE YEAR LIMITED WARRANTY PERIOD Some states or provinces do not allow disclaimer of the implied warranty with respect to consumer goods so the foregoing disclaimer may not apply to you This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state or province to province If the appliance should become defective within the warranty period do not return the appliance to the store Please contact our Customer Service Center Toll free phone number 1 866 BREVILLE 1 866 273 8455 Internet email AskUs BrevilleUSA com AskUs Breville ca in Canada ORGINAL RECEIPT IS REQUIRED FOR ALL RETURNS HWI Breville products are distributed in Canada by Anglo Canadian Housewares L P and in USA by Metro Thebe Inc
34. ss 2 more times to completely renew the water from inner tank Setting Setting the the time w You mus TIME fe 1 Press option blinkir 2 Press indica 3 Press appro indica 4 Once OK b that tt 5 Press appro 6 Once the O menu continued brew ed button te The oved to S flow card the mpletely BR9013 BKC600XL_IB_AMEND qxp 11 10 07 e Page 17 Menu and programming options Setting the CLOCK SET feature Setting the clock is optional When the clock is set the time will appear on the LCD screen You must set the clock if using the ON OFF TIME feature 1 Press the MENU button The menu programming options will appear on the LCD screen with a blinking indicator on CLOCK SET 2 Press the OK button The hour will blink indicating the hour is ready to be set 3 Press the or button to reach the appropriate hour If the hour has passed 12 the indicator switches from AM to PM C S CLOCK SET 4 Once the appropriate hour is reached press the OK button The minutes will blink indicating that the minutes are ready to be set 5 Press the or button to reach the appropriate minute 6 Once the appropriate minute is reached press the OK button The LCD screen will return to the menu programming options 7 To exit the menu programming options press the MENU button Alterna
35. the MENU button and scroll Some sta through the programming options Both the ON OFF TIME and AUTO of the imp OFF features should be INACTIVE If INACTIVE is not displayed follow goods so the instructions Setting the ON OFF TIME feature page 17 and Setting to you the AUTO OFF feature page 19 This warre The blue light in the The water level is low and a full cup cannot be brewed Add water to may also water tank is flashing the Water Tank following the instructions Re filling the Water Tank state to st page 15 Warranty BR9013 BKC600XL TB AMEND qxp 11 10 07 zeke Page 27 Ider caling mes set it sature lt again d scroll JTO follow Setting to K One year limited warranty Breville warrants this Breville appliance against defects that are due to faulty material or workmanship for a period of one 1 year from the date of original consumer purchase This warranty does not cover damage from abuse neglect use for commercial purposes or any other use not found in the printed Instructions for use booklet There is no warranty for glass parts glass containers filter basket blades and agitators HWI Breville expressly disclaims all responsibility for consequential damages for incidental losses caused by use of this appliance Some states or provinces do not allow this exclusion or limitation for incidental or consequential los
36. tively press the button to reach EXIT MENU and press the OK button The LCD screen will return to the main screen and indicate the time selected If power is interrupted to the Brewer the clock will need to be reset Programmed brew size and brew temperature settings are remembered and restored automatically All other settings will be restored automatically after the clock is reset Setting the ON OFF TIME feature This feature allows you to program the specific time when the Brewer will automatically turn on and or off By programming your Brewer to automatically turn on you will not have to wait for the Brewer to lt gt heat the water in the Water Tank It will take the Brewer approximately 3 7 minutes to heat the water from room temperate You must set the clock if using the ON OFF TIME feature An alternative to setting the ON OFF TIME feature is to leave the Brewer on all the time We recommend this so your Brewer is always ready to brew a fresh cup of gourmet coffee tea or hot cocoa To turn the Brewer off at any time press and release the Power Switch on the lower back right side of the Brewer The clock will remain on if set however you can not activate the brew cycle Press and release the Power Switch again to restore power to the Brewer You will have to wait for the water to heat up before the Brewer is ready to brew BR9013 BKC600XT TB AMEND qxp 11 10 07
37. ty of you use an adapter Assist Plug conveniently designed with a finger ing any hole in the power plug for easy and safe removal from the wall outlet For safety reasons it is recommended you plug your Breville appliance directly into its own electrical outlet on a dedicated circuit separate from other appliances If the electric circuit is overloaded with other Consult a qualified electrician if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is UL i properly 0 Regularly inspect the supply cord plug and actual appliance for any damage Do not operate of the appliances your Brewer may not function not if damaged m anyway or after the appliance properly Use in conjunction with a power strip or 4 malfunctions Immediately cease use of the extencion cord is not recommended appliance and call Breville Customer Service at 1 866 BREVILLE for examination repair or Holder adjustment of oo e For any maintenance other than cleaning call MM c Breville Customer Service at 1 866 BREVILLE e the a SHORT CORD INSTRUCTIONS Your Breville appliance is fitted with a short power supply cord as a safety precaution to prevent personal injury tatu and or property damage resulting from pulling tripping or becoming entangled with a longer cord Do not allow Wher the children to use or be near this appliance without close adult supervision If an extension cord is used 1
38. zeke Page 18 Menu and programming options continued Setting the ON OFF TIME feature continued 1 Press the MENU button The menu programming options will appear on the LCD screen with a blinking indicator on CLOCK SET Press the button to reach ON OFF TIME Press the OK button st 13 ON OFF TIME INACTIVE eON OFFTIME ACTIVE as Cm Cm AOO 00 Press the or button to see the two options ON OFF TIME will be INACTIVE indicating that the Brewer will not turn on or off automatically Press the OK button to select this option The LCD screen will return to the menu programming options ON OFF TIME will be ACTIVE indicating the Brewer will automatically turn on and or off according to the specific times you set Press the OK button to select this option Setting the ON TIME i The LCD screen will display ON TIME indicating that the time you wish the Brewer to automatically turn on is ready to be set The hour will blink indicting the hour is ready to be set ii Press the or button to reach the appropriate hour If the hour has passed 12 the indicator switches from AM to PM i Once the appropriate hour is reached press the OK button The minutes will blink indicating that the minutes are ready to be set Press the or button to reach the appropriate minute

BREVILLE BKC600XL User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents