BOXLIGHT MP-93i User's Manual
Contents
1. Lf ks MA VTR with S VH Computer Desk type Paint aay 2 O O O VTR etc video model only Oj 10 Audio amplifying equipment CRT Display 27 28 Cleaning the air filter Clean the air filter about every 100 hours 1 Turn the main power switch off and disconnect the power plug from the power outlet 2 Remove the front filter cover 3 Clean the air filter using a vacuum cleaner e When air filter is very dirty wash it using neutral detergent diluted with water and dry well 4 Attach the air filter on the cover Air filter Filter cover vl V e f air filter is strutted with dust etc protection circuit will turn the power off e Do not use with removed air filter Lamp Light source lamp has a service life The picture will become dark or color will be poor when the lamp is used for a long time If usage of lamp is continued in such cases it could cause a malfunction Replace lamp with new one As reference for replacement time indicator will operate or message will be displayed when the power is turned on as shown on page 30 31 In these cases the lamp should be replaced Consult your dealer Also LAMP indicator will light when the lamp becomes too hot Turn off the power and let the projector cool for 45 minutes Turn on If LAMP indicator st2. lt Manual Operation gt Adjust optional items manually SELDUR INEST IMAGE DPI VOLUME 1 Use the MENU buttons on the unit or the DISK PAD on the remote BRIGHT r CONTRAST control to move the green cursor to the number of the item you wish to V POSIT F H POSIT adjust H PHASE 2 With the green cursor on the number use the MENU buttons on the COLOR BAL unit or the DISK PAD on the remote control to raise or lower the value Adjustments and functions continued lt AUTO adjustment gt The projector will automatically adjust four items V POSIT H POSIT H PHASE H SIZE White level When AUTO is selected the cursor is moved from Manual Operation towards the right the AUTO Confirm screen shown below will be displayed v lt AUTO adjustment Confirm Screen gt SETUP INPUT IMAGE OPT mr While the AUTO confirmation screen is displayed as illustrated on the VOLUME S L upper right if you shift the cursor upward and selet AUTO the projector CONTRAST will perform auto adjustment ed It will become as illustrated on the lower right HP If CANCEL is selected for three seconds or if the RESET button on either fe on BAL the unit or the remote control is pressed the green cursor will return to the value for the selected item Manual Operation lt During AUTO adjustment gt At the lower right of the screen the word lt AUTO gt will flash in green letters When the auto adjustment i
3. The following messages are displayed on the screen CHANGE THE LAMP Accumulated operation of lamp has exceeded 1 700 hours It is recommended AFTER REPLACING LAMP to replace lamp Replace with new lamp If accumulated operation reaches RESET THE LAMP TIMER 2 000 hours lamp will automatically turn off 1 CHANGE THE LAMP Lamp has 1 979 hours on it AFTER REPLACING LAMP Call a maintenance person 1 RESET THE LAMP TIMER Time is 20 0 count down THE POWER WILL TURN OFF AFTER 20 Hr Blinking of When the lamp has 2 000 hours or more on it the message will blink and the CHANGE THE LAMP power will turns off after 10 minutes 2 NO INPUT IS DETECTED Signal is hot input See page 19 20 The horizontal frequency of the input signal exceeds the range of the projector it cannot be displayed See page 20 21 SYNC IS OUT OF RANGE 1 This message are not displayed after 3 minutes But this message are displayed when you turn on the power again 2 It is possible to again turn on the power however the power will go off after about 10 minutes Message table continued Indicator display The ON indicator LAMP indicator and TEMP indicator will light or blink in the following cases ON marcator LAMP acatar TEMP naico Meaning Ronedy d C PS atts goon Goes _Goosot oumngvamngup tans goon coeso coson fooro S Paints orange Coosa Goosct_ ounngcooingaown ENGLISH Cool projector b
4. 130 02 Sroa eaea g 12 24 107 06 Sn a io ee s o Senere io f 2s 18 fos STOA TIT 73H 11 18 95 01 Back porch b Front porch d Active c AE DATA Oo VSYNC Sync a Computer signal venra e asa ar svea vere 3 at 600 i svea 3 27 600 i Mac G ro EAERI xao 6 20 7a 3 vemena 3 60 350 32 _ Posso s 25 400 7 Vertical Timing Ces a b Cc Mac tarmode 3 39 480 3 _xGA 7ora 6 2 7a 3 XGA 76H2 s 28 7e Soas x04 TR 3 s2 B64 1 xea x960 or 3 36 960 1 SeA 3 98 ioa SXGA 1280X 1024 Skz 3 a38 1024 1 21 22 Connection to the control signal terminal 1 Control signal terminal HEE Ponta Poa es E p r ofm D sub 15pin shrink terminal Male a oe z ea a ee SE ee ae ae E Turn off the power of both the projector and computer before connecting Connect the computer to the control terminal of the projector using an appropriate cable Refer tothe instruction manual of each device before connecting 2 Mouse emulation 1 Connect the projector and the mouse terminal of computer using an appropriate cable while the projector and the computer are turn off 2 Turn the main power switch of the projector on and press the STANDBY ON button The indicator will light The ON indicator will light up green 3 Press the INPUT of the projector or RGB button of the remote control
5. continued To turn off the power 1 o A ENGLISH RESET RIGHT MOUSE ON BLANK TIMER RGB VIDEO pnu 1 Press the STANDBY ON button for 1 second e The ON indicator blinks orange and the lamp turns off About 1 minute later the fan stops and the indicator lights up orange e Press the STANDBY ON button for short time less than 1 second the projector do not set in standby mode 2 Turn the MAIN POWER switch of the projector off OFF 3 Install the lens cap e To reduce temperature inside the projector fan will rotate for about 1 minute after the lamp is turned off e Donot turn off the MAIN POWER switch during the lamp on because the lamp is damaged PLUG amp PLAY This projector complies with VESA DDC1 2B specifications PLUG amp PLAY is a system with computer peripherals including projectors and operating system It works when the projector is connected to DDC Display Data Channel ready computer that is running an operating system software that incorporates plug amp play functionality Only RGB 1 13 Basic operations continued FREEZE FUNCTION This function can display a still picture by freezing This function can STANDBY ON MUTE be used in combination with a MAGNIFY function J 9 Se U 1 Press the FREEZE button BS The display image stops A J mark appears at the lower right of STR a the screen for about 3 seconds during the FREEZE function
6. lower 00h 00h 24h higher 00h 00h 00h less 00h 00h 24h more 00h 00h 00h red 00h 00h 24h green 00h 00h 00h soft 00h 00h 24h sharp 00h 00h 4Fh 00h left 00h 00h 17h O5h right 00h 00h 06h 06h narrow 00h 00h 04h OCh wide 00h 00h 03h 00h down 00h 00h 00h 06h up 00h start 07h stop OXh Blank off 1Xh Blank on BLANK bitO O Blue off 1 Blue on bitt O Green off 1 Green on bit2 O Red off 1 Red on bit3 O Not change 1 change REVEAL X1h Reveal down X4h Reveal right X 0 slow 7 fast 1 Circuit codes when ask code and default set code are issued Number of data byte 1 00h normal display 01h magnified display 2 When magnification is set by setting codes Number of data bytes 6 1st 2nd data bytes magnification starting positions in horizontal direction left end MAGNIFY 00h OOh left 3Ch O5h right 3rd 4th data bytes magnification starting positions in vertical direction top 00h OOh top ODh 04h bottom 5th 6th data bytes Horizontally magnified dot number data 64h 00h large 20h 06h small FREEZE OOh normal display 01h still picture display If computer sends the undefined command code or data code Projector can not guarantee operation Command is consisted of 2 command bytes and following data bytes 1 st byte indicates the kinds of commands and the length of command OxH Error reply Projector sends to computer IxH Command reply Projector sends to co
7. not support the projector to avoid falling of the projector and causing an injury e Do not revolve the foot adjusters by force the foot adjusters is damaged e Securely lock the adjuster e Do not apply unnecessary force from the upper side when lifting the projector Otherwise projector may be damaged or a finger could be caught and cause injury 11 Basic operations To project the picture oA NI _ 3 4 5 6 T FREEZE Sac f MAGNIFY VOLUME AAS POSITION ON LASER RESET RIGHT MENU ON MOUSE ON BLANK TIMER VIDEO RGB ero Turn the MAIN POWER switch of the projector on I ON e The ON indicator will light up orange Press the STANDBY ON button e The ON indicator blinks green during warm up and then lights green e Power cannot be turned on even if the STANDBY ON button is pressed within 60 seconds after power is turned off since the lamp has cooled preparing for next lighting Remove the lens cap Adjust picture size using the projection lens ZOOM knob Adjust focus using the projection lens FOCUS ring Power on all connected equipment The method of connecting various equipment see on the page 19 27 Press the INPUT button or the INPUT SELECT VIDEO or RGB button to select the source of the signal to be projected on the screen e The selected signal input is displayed at the bottom right of the screen ih eek for 3 seconds RGB1 Basic operations
8. p 75Q termination SvIBEO signal Chrominance signal 0 286Vp p burst signal 75Q termination VIDEO signal 1 0Vp p 75Q termination 200mVrms 20k below MAX 3 0Vp p AUDIO signal Output 0 200mVrms 1kQ 2 Signal input terminal Chrominance signal Luminance signal ENGLISH oo o9 S VIDEO input Mini DIN4 pin Video input signal terminals have priority in the following order S VIDEO input terminal RCA jack input terminal Even when the video signal is displayed only an audio signal is output to RGB audio output terminals Connection to the RGB signal terminal 1 Input output signal Video signal Analog 0 7Vp p 75Q termination Positive polarity Horizontal sync signal TTL level Positive negative polarity Vertical sync signal TTL level Positive negative polarity Composite sync signal TTL level BENO 200MVrms 20KQ below MAX 3 0Vp p 0 200mVrms 1kQ 2 Signal input output terminal Waco sal Red 8 NG Blue a 7 2 F N C DDC Display Data channel RGB1 only iG Kal Ea EA 1 2 INC 12 Horizontal Composite sync signal Ground for R Vertical sync signal 7 Ground for G DDC Display Data channel RGB1 only Ground for B Do not use RGB cable other than that specified Some RGB cable may not operate DDC Display Data Channel D sub 15pin shrink terminal Female because there are not connect from pin NO topin NO Connection to the
9. the button is pressed TO RETURN TO NORMAL DISPLAY 6 Press MAGNIFY OFF button Note The MAGNIFY function is released when an input selector button is pressed or when the display mode of a personal computer is switched over during display Adjustments and functions A STANDBY ON MUTE FREEZE Ole MAGNIFY VOLUME Glee STANDBY ON C INPUT O POSITION ON LASER ENGLISH 1 Press the MENU 7 buttons or the MENU ON OFF button e On screen menus are displayed on the screen NO Select the menu to be adjusted using the MENU buttons or DISK PAD e Menu displayed in green is selected GO Select the item to be adjusted using the MENU 7 buttons or DISK PAD e Item displayed in green can be adjusted When no operation is done for about 5 10 seconds menu screen will go off Memory function Individual memory functions are provided for the VIDEO RGB1 and RGB2 input terminals Adjustments are saved after power off To return to the initial setting e Resetting menu items SETUP INPUT IMAGE OPT 1 Select the menu item to return to the initial setting 2 Press the RESET button 3 Select the DEFAULT To select the CANCEL is not changed Display shown on the right will appear SETUP INPUT IMAGE OPT RESET SETUP E DEFAULT DO CANCEL e Resetting adjustment items VOLUME BRIGHT etc 1 Select the adjustmen
10. transmitter and select the input connection 4 Turn on the computer 5 Start mouse emulation mode If can not start mouse emulation reset the computer With soft reset or reset switch 6 See on the page 9 about to operate the remote control transmitter Caution M ouse cannot be operated while start up screen or menu screen is being displayed e n some note computers which have internal pointing device mouse emulation don t work without setting the internal pointing device disabled In this case set the internal pointing device disabled in BIOS setting After setting in BIOS operate 1 5 Please check its hardware manuals to disable internal pointing device in BIOS setting e n some computers mouse emulation don t work without the utility program In this case see and check the operating manuals of the computer Connection to the control signal terminal continued PS 2 mouse Projector Computer 8 DATA CLK ini Dj BATE ou 3 GND Mini Din 6pin S 5V CLK SELO 6 O RTS n 5V CQ NJ W PS 2 cable ADB Mac mouse Projector Computer 1 ADB n POWER ON Mini Din 4pin DATA G 5V 4 GND RTS 5V Q GND QO ADB cable Serial mouse Projector Computer 5 GND D sub 9pin RTS 9 0 RTS O00000 0000 Serial cable Communication via RS 232C cannot be operated with Serial mouse cable Purchase RS 232C cable Type name Cable serial interface Parts No ZU 0
11. 243 70 0010 23 Connection to the control signal terminal continued 3 Communication 1 Connect the projector and computer using RS 232C cable 2 Turn off the computer and after computer is setting up turn on the projector 3 Select the data speed COM SPEED and the data format COM BITS of the projector See page 18 4 Start communication Projector Computer 1 CD 2 RD 3 TD 4 DTR 6 GND D sub 9pin SELO 6 6 DSR 00000 RTS 7 7 RTS 0000 8 CTS 9 RI GND 0 RDP 3 TDP RS232C cable Reference 4 Control command table Control command table Prefect Comparer Computer Projector m o POWER on on n em th omn m A n oh 3 h oh e n oh 3 Reven o amn n en am on a _ 1 40h 15h 11h 15h 20h 15h anini 16h 15h 6 36h 15h 6 FREEZE 11h 16h 1 20h 16h 31h 16h 1 40h 16h Connection to the control signal terminal continued Control data table MOUSE OOh stop mouse emulation 01 7Fh start mouse emulation OXh 8N1 1Xh 7N1 COMMUNICATE XOh 1200bps X1h 2400bps X2h 4800bps X3h 9600bps X4h 19200bps POWER 3Eh Power off Standby mode 3Fh Power on MIRROR OOh Normal 01h H Invert O2h V Invert OS3h H amp V Invert INPUT 11h VIDEO 21h RGB1 22h RGB2 00h OOh Auto 00h O1h NTSC 00h 04h NTSC4 43 DEC TEY 00h 02h PAL 00h 03h SECAM 00h 05h M PAL 00h O6h N PAL 00h min 24h max 00h 00h 00h dark 00h 00h 24h brite 00h 00h 00h
12. Do not use this unit in a bathroom etc This may cause a fire electric shock etc Do not use near water E Do not look directly at the lens when the lamp is lit Do not look directly at the lens when SO the lamp is lit Since a strong light is used it could damage you vision etc Especially pay attention if children are present E Do not insert any foreign object e Donot insert a metal or flammable object inside through the ventilation S holes etc This may cause a fire electric shock etc e e f foreign matter enters inside turn the power switch off and disconnect the power plug from the power Pull out the tlet and contact your dealer 1f OWS Plug outlet and contact your dealer fromthe you use as it is it may cause a fire power let electric shock etc Be careful outst especially if children could touch the unit E Do not apply any shock If you drop this unit or if the cabinet Z is broken turn off the power switch Pull out the disconnect the power plug and power plug contact your dealer If you useit as fromthe it is it may cause a fire electric een shock etc E Do not remodel this unit Do not remodel this unit It may O cause a fire electric shock etc Prohibition of disassembly E Do not put a container etc with liquid on this unit Do not put a vase flowerpot SO cosmetic container medicine or water and small metal objects on this unit If liquid spills and en
13. FOR CLASS EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse the value of which is indicated on the pin face of the plug Should the fuse need to be replaced an ASTA or BSI approved BS 1362 fuse must be used of the same rating If the fuse cover is detachable never use the plug with the cover omitted If a replacement fuse cover is required ensure it is of the same colour as that visible on the pin face of the plug Fuse covers are available from your dealer DO NOT cut off the mains plug from this equipment If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point then obtain an appropriate safety approved extension lead or consult your dealer Should it be necessary to change the mains plugs this must be carried out by a competent person preferable a qualified electrician If there is no alternative to cutting off the mains plug ensure that you dispose of it immediately having first removed the fuse to avoid a possible shock hazard by inadvertent connection to the mains supply WARNING THIS EQUIPMENT MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code Green and Yellow arth Blue Neutral Brown Live Green amp Yellow to Earth Brown to Live Fuse Blue to Neutral Cord Clamp As these colours may not correspond with the coloured maki
14. IN POWER switch on le The power cord is disconnected Insert the power cord into an AC socket 60 seconds have not elapsed since the J When the power is turned off turn the power power was turned off switch on after waiting at least 60 seconds eInside the projector too hot eDo not block the ventilation holes leClean the air filter leUse the projector under 35 C temperature No picture and eThe setting of the input source is not leSet the correct input using the input select button 7 Fe Sound correct of the projector or the remote control leWiring to the projector is not correct leConnect the cable correctly 5 8 ye Only picture is Wiring to the projector is not correct eConnect the cable correctly displayed with no le The volume is set to minimum Press the VOL button or press the MENU button aera and adjust the volume eThe unit enters the mute mode lePress the MUTE button leWiring the projector is not correct leConnect the cable correctly Power cannot be turned on Only sound is le The brightness is set fully to the dark ePress the MENU button and select BRIGHT and P16 heard without a picture side press the button Lens cap is attached leRemove the lens cap Color is weak and The color and tint have been adjusted leThe brightness and contrast has been __jeAdjust the brightness and contrast correctly P 16 Picture is dark adjusted incorrectly leThe lamp has not been adjusted Replace the l
15. Only RGB signal input While the back light on you can operate POSITION 1 DISK PAD When the back light of MENU ON button on selects or adjusts the menu item See page 15 When removes the on screen menus works as mouse When the back light of the POSITION ON button on moves picture 2 MENU ON button Displays the on screen menus And back light on See page 15 18 While the back light on you can operate MENU BLANK ON button The blank screen which is displayed by pressing BLANK And the blank screen will be revealed down by pressing BLANK again See page 18 INPUT SELECT button Selects the input source See page 12 1 POSITION ON icon When presses POSITION ON button back light on and icon is displayed While displaying the icon you can operate POSITION Icon is displaying in video mode but can not operate POSITION A STANDBY ON MUTE GEEKS ah MENU ON MOUSE ON BLANK TIMER RGB VIDEO a ineur y 2 MUTE button Silences the sound Cancels the mute when the unit is set in mute mode VOLUME button Adjusts volume The sound is loud or low while pressing the or button LASER button Laser pointer ON button Use as a stick for indication See page 10 MOUSE LEFT button Mouse left button is the left click of the mouse bottom button See page 22 RESET RIGHT button When displays the on screen menus
16. RGB signal terminal continued 3 Example of computer signal Resolution fH fV Standard Display Dots HXV kHz Hz Type play 640 X 400 248 sea fo NEC PC9800 fo Expanded 1024 X 640 40 Xo vesa vani xpanaea t008 x 0 640 X 400 VESA VGA 2 Expanded 1008 X 640 720 X 400 VESA TEXT Expanded 1008 X 640 640 X 480 VESA VGA3 Expanded 1024 X 768 EE H a E 800 X 600 VESA SVGA 85Hz Expanded 1000 X 750 o e woo ven er aa mo o ven p Note 1 Signal mode Note 2 MAC adapter is necessary to the resolution mode Projector is compatible with 13 inch mode and 16 inch mode MAC13 mode switch 1 and switch 2 are ON MAC16 mode switch 2 and switch 4are ON Note 3 Display mode Example 16inch mode e Some input source may not be displayed properly because they are not compatible with the projector e Some input source may not be displayed in full size as shown Display Dots Connection to the RGB signal terminal continued 4 Initial set signals The following signals are initially set The settings may be different depending on the computer type In this case adjust the settings referring to pages 15 16 Back porch b Front porch d Active c ENGLISH DATA HSYNC Sync a Computer signal Horizontal Timing us es TEXT ons fes 1s asa 08 VOAS 72H2 C svea esha 11 27 tae 06 Mac te mode 11 39 145 06 xene 21 25 158 04 Soa E XGA 75H t2 22
17. Sea HT I CORPORATION Liquid Crystal Projector Model name MP 931 OPERATING GUIDE ENGLISH Thank you very much for purchasing this BOXLIGHT Liquid Crystal Projector Please read this operating guide to use correctly After reading this manual keep it carefully for future reference Outline This Liquid Crystal Projector can display various computer signals and NTSC PAL SECAM video signals Features 1 High brightness A highly efficient optical system with a UHP lamp ensures high brightness 2 High resolution Three separate high definition liquid crystal panels are used for the R G and B signals 3 Compact size light weight for portability 4 RGB output terminal 5 RS232C Communication 6 Mouse emulation 7 Power zoom and power focus functions 8 Complies with VESA DDC1 2B specifications 9 Auto adjustment function Contents Page Before use Contents of shipping box Names and functions of each part 7 Installation Basic operations Adjustments and functions Connection to the video signal terminals Connection to the RGB signal terminal Connection to the control signal terminal Example of system setup When you think something wrong 31 Specifications FOR THE CUSTOMERS IN U K THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE FOR THE U K PLEASE REFER TO THE NOTES ON THIS PAGE IMPORTANT FOR UNITED KINGDOM WORDING
18. T IN DEN STRAHL BLICKEN LASAER KLASSE 2MANUFACTURER A MADE IN JAPAN CLASSI LASER PRODUCT LASER APERTURE Installation Example of the projector and screen installation Determine picture size and projection distance as illustrated below View from the top View from the side Screen Lens center ENGLISH a Distance from the projector to the screen tolerance 10 This screen size is full screen size 1024 dots X 768 dots Installation of liquid crystal projector Please basically use liquid crystal projector at the horizontal position If you use liquid crystal projector by the lens up position the lens down position and the side up position this may cause the heat inside to build up and become the cause of damage Be especially careful not to install it with ventilation holes blocked Screen inch Adjust the projection position using the foot adjusters at the bottom of the projector View from the front View from the side op g Vertical adjustments can be made in the range of 0 to 9 Foot adjuster N W k Horizontal inclination may be adjusted using the adjuster at the rear 1 Lift up the projector and press the button of the adjuster to release the lock 2 Adjust the projection angle release the button of the adjuster and securely lock it 3 To adjust the angle slightly revolve the foot adjusters e Do not unlock the foot adjusters while you do
19. amp with a new one P 29 Picture is not clear Focus or H PHASE is not matched Adjust the focus or H RPHASE P 12 16 LAMP indicator Turn off the power and leave for 45 minutes lights red Trouble with the lamp then turn the power on again Remote control eCable was connected after the power __ eBe sure to perform procedure in the following order mouse cannot be was turned on 1 Connect cable 2 Turn on projector 3 Turn PC on P22 e RGB signal not selected le nput RGB signal and select and display input 3 operated EETA A bright dot may be seen in the picture This is a phenomenon peculiar to the liquid crystal and is not a problem 31 32 S pec fi cat O n S e All specifications are subject to change without notice aa ar X aar fxetuay foo aduaton X 102 oregon S VIDEO Mini DIN4 pin terminal input terminal VIDEO RCA Jack terminal Input Output AUDIO RCA Jack terminal terminal RGB input output RGB signal D sub 15pin shrink terminal Female signal terminal AUDIO Stereo mini jack Control terminal D sub 15pin shrink terminal Male Remote control MAC adaptor Accessories POWER code Video Audio cable BATTERIES LR6 2 Mouse cable RGB cable Operating guide Dimension diagram All dimensions shown in inches Video signal a e9 Leal amr oS 5
20. aw TO RELEASE FREEZE N Press the FREEZE button The freeze function is cancelled Furthermore a mark appears at the bottom of the screen for 3 seconds or so when FREEZE is released e Note When the FREEZE Button is pressed FREEZE and RELEASE can function alternately e What is more FREEZE is released when an input selector button is pressed or when the display mode of a personal computer is switched over during display e The POSITION ON icon is not displayed during freeze Also scrolling using DISK PAD operation is not possible e When a still picture signal is given as input and the freeze function is ON do not forget to cancel the freeze function MAGNIFYING FUNCTION It is possible to display a partially magnified picture This function can be used in combination with a FREEZE function 1 Press the MAGNIFY button e By doing so the center of the picture can be magnified as one STANDBYION MUTE part becoming double in size 1 2 ap TO CHANGE MAGNIFICATION r 5 2E 2 Press the MAGNIFY button FOSTON oN e When the button is pressed more magnification of display o takes place Maximum about 4 times 4 3 3 Press the MAGNIFY button e When the button is pressed the magnified display reduces its 5 size Minimum about 1 1 times TO SHIFT DISPLAY AREA 4 Press the POSITION ON button 5 Press the DISK PAD button up and down and left and right e The magnified display area shifts in the direction
21. box Check that the carton contains the following items ENGLISH Liquid Crystal Projector Remote Control Transmitter Operating Guide batteries included o Power Cord 3 Conductor RGB Cable Mac adapter Mouse cable x3 110V US Video Audio Cable 15 15 pin M M with dip switch Names and functions of each part Main unit ON indicator This blinks in the standby mode and lights in the operation mode See page 31 STANDBY ON button Power ON OFF button OFF sets the unit in standby mode see page 12 13 MUTE button Silences the sound Cancels the mute when the unit is set in mute mode INPUT button To select the input source Each time this button is pressed the input source is changed in sequence as shown below See page 12 RGB1 gt RGB2 gt VIDEO RESET button Resets unit to factory settings See page 15 MENU button Picture adjustments Refer to page 15 18 for details Lamp LAMP indicator Crewe TEMP indicator This lights or blinks when temperature inside the projector is too high or when fan is abnormal See page 31 This lights or blinks when the lamp does not light See page 31 Speaker ZOOM knob Adjusts picture size Speaker See page 12 Remote control Cooling fan sensor exhaust Lens Lens cap Cooling fan Handle in take e Use the remote control transmitter within the range FOCUS ring of about 16 feet from the
22. ed to the ground Or if normal coaxial cables are used the cables must be enclosed in metal pipes or similar way to reduce the interference noise radiation 2 Power cord Shielded power cord must be used The outer shield must be connected to the ground 3 Video inputs The input signal amplitude must no exceed the specified level Before use Before Use Illustrated marks Various illustrated marks are used in this product and instruction manual so the product is used correctly and safely and also to protect you and others from danger and your property from being damaged This shows that a person could be killed or injured if the AN arn I ng wrong operation is done by ignoring this indication 7 This shows that a person could be injured or material may be AN aution damaged if the wrong operation is done by ignoring this indication Examples of The A mark informs you that there is a warning including caution The concrete details of the warning the left diagram shows the caution for an electric shock hazard is shown in the diagram illustrated marks prohibited action the left diagram shows the prohibition of The mark informs you of a prohibited action The concrete disassembly is drawn in the diagram or near it The mark informs you of actions you must do The concrete g instruction details the left diagram shows Disconnect the power plug from the power outlet is drawn in the diagram Safety
23. ept command from PC error code 00H yyH is sent back in a case when command code 2xH 3xH or 4xH t yyH data is sent from PC to projector The example of data error When projector cannot accept command from PC error code with data 00H yyH data is sent back as it is in a case when command code 2xH 3XH or 4xH yyH data is sent from PC to projector When data is longer than required data code length projector ignores excess data code When data is shorter than required data code length projector sends back error code shown above The example of framing error Projector sends error code 70H 70H up to 10 times at intervals of 1 second until any answer is received The interval of command bytes and data bytes After command code 2xH 3xH or 4xH is sent from PC if command or data is not sent within 500ms projector sends back error command 70H 70H If no answer is sent within 1 second from that time framing error is assumed e The interval of command bytes and data bytes must be over 1mS and under 500m5 If it is under 1mS it may be treat as framing error e After projector has sent back answer code when next command is to be sent from PC allow for an interval of 40ms or more between answer code and other code Example of system setup Connecting various equipment ENGLISH AC Inlet Computer Note type S VIDEO IN
24. ill lights up red contact your dealer 1 How to replace lamp Option lamp Lamp unit DT00201 HIGH VOLTAGE AN AN AN HIGH TEMPERATURE HIGH PRESSURE When replacing lamp turn off and remove AC cord wait 45 minutes to let lamp cool High pressure lamp when hot may explode if improperly handled e For disposal of used lamp treat according to the instruction of community authorities e Since the lamp is made of glass do not apply shock to it and do not scratch it e Also do not use old lamp This could also cause explosion of the lamp e f it is probable that the lamp has exploded explosive sound is heard disconnect the power plug from the power outlet and ask your dealer to replace lamp The lamp is covered by front glass and air tight structure but in rare cases the reflector and the inside of the projector may be damaged by scattered broken pieces of glass and broken pieces could cause injury when being handled Front glass 1 Turn the main power switch off and disconnect the power plug from the power outlet 2 Remove the lamp cover e f lamp is hot at this time this could cause burn Wait for minimum 45 minutes until lamp is cooled down e Loosen a screw and remove the cover Screw 3 Loosen two screws and pull the handle to remove the lamp e f the screws are not loosened completely your fingers may be damaged e Do not insert your hand into the box after the lamp is removed There are optical pa
25. mputer 2xH Ask command Computer sends to Projector 3xH Set command Computer sends to Projector 4xH Default set command Computer sends to Projector 5xH FxH Reserved x indicates the length of data bytes 2 nd byte indicates the command code yy as command table Data table shows the data byte ENGLISH 25 26 Connection to the control signal terminal continued The procedure of getting the Projector status 1 Computer sends the command 20H tyyH to Projector 2 Projector reply the command 1xH yyH data bytes The procedure of setting the Projector status 1 Computer sends the command 3xH yyH data bytes 2 Projector changes it s status 3 Projector reply the command 1xH yyH data bytes which indicate status e 3 data bytes is not always same as 1 data bytes If projector cannot realize the status of 1 data bytes projector set the proper status and reply this new setting data bytes or projector reply the error reply OxH yyH t data bytes same as 1 e When only power control POWER COMMAND is performed it takes about 2 140 seconds between sending set code and receiving answering code The procedure of default setting the Projector status 1 Computer sends the command 40H yyH 2 Projector changes it s status to default setting 3 Projector reply the command 1xH yyH data bytes which indicate default The example of command error When projector cannot acc
26. ngs identifying the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Y ellow The wire coloured Blue must be connected to the terminal marked with the letter N or coloured BLUE or BLACK The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense ENGLISH Instructions to Users This equipment complies with the requirements of FCC Federal Communication Commission Class A equipments provided that following conditions are met 1 Video signal cables Double shielded coaxial cables so called FCC shield cable must be used and the outer shield must be connect
27. nnect the power plug with wet hands It may cause S an electric shock e When the power plugis to be disconnected do not pull the power cord The power cord may be damaged and it may cause a fire electric shock etc Be sure to hold the power plug Pull out the power plug from the power outlet E Caution when carrying it When this unit is to be moved apply a cover to the lens and be sure to disconnect the power plug from the power outlet and check that all external connection cords are removed before moving it If not the cord may be damaged and it may cause a fire electric shock etc Caution E Use of batteries e Do not use batteries not specified for this unit Do not use new batteries mixed together with old ones This may cause a fire injury due to burst of battery liquid leakage e When inserting batteries in this unit pay attention to the direction of the and polarity indications and insert the batteries correctly If the polarities are confused it may cause injury or damage near the unit due to burst batteries liquid leakage etc E When you are not going to use for a long time When you are not going use this unit for a long time because you are going on a trip etc be sure to pull out the Pull out up power plug from the power outlet for fore Ph safety And also apply cover tothe power lens so that the lens is not damaged outlet E Clean inside the unit at least once t
28. precaution A Warning E If any abnormality occurs e When there is an abnormal smell or smoke if you use this unit as it is this could cause a fire or electric shock etc When an abnormality is found immediately turn off the power switch and pull out the power plug from the power outlet Check that there is no smoke etc then contact your dealer to repair the unit Do not repair it yourself as it is very dangerous Do not use this unit as it is after trouble has occurred such as No picture No AN g sound Abnormal sound etc This may cause a fire R electric shock etc In this case from the immediately turn off the power steel switch and disconnect the power plug then contact your dealer to repair the unit If water etc enters inside the unit turn off the power switch of the unit first and disconnect the power plug and then contact your dealer If you use it as it is it may cause a fire electric shock etc E Do not install this unit in an unstable place Avoid placing it in an unstable place such as weak base inclined floor etc This may cause it to drop or fall over S resulting in injury E Do not open the cabinet Do not open the cabinet There are high voltage AN Q parts inside the cabinet and this may cause an Electric shock Prohibition electric shock Ask your zard or aas disassembly dealer to check inside and adjust and repair the unit E Do not use this in a bathroom etc
29. remote control sensor and Adjusts focus See page 12 within 30 to both the left and right Names and functions of each part continued Remote control sensor MAIN POWER switch Main power ON OFF switch O OFF ON VIDEO input terminal on video equipped models only S VIDEO input terminal AC IN socket Mini DIN 4pin connector Connect the provided power cord VIDEO input terminal RCA Jack AUDIO L R input terminal RCA Jack D SVIDEO IN 2 NI D o D RGB input terminal VIDEO IN D sub 15pin shrink terminal 1 2 ONTO O RGB OUT AUDIO IN G OREO more HO ef CONTROL terminal D sub 15pin shrink terminal AUDIO output terminal RGB VIDEO Stereo mini jack AUDIO input terminal RGB output terminal Stereo mini jack 1 2 D sub 15pin shrink terminal RGB output can be displayed even in the standby mode Names and functions of each part continued Remote control transmitter STANDBY ON button Power ON OFF button OFF sets the unit in standby mode See page 12 13 FREEZE Button Pressing this button displays a still picture by freezing See page 14 MAGNIFY button Pressing this button partially magnifies a displayed picture See page 14 POSITION button Moves the picture by DISK PAD after pressed the POSITION ON button
30. resets the menu item to factory settings When operates the mouse emulation works as right click of mouse in computer mode See page 22 After moving the picture POSITION ON resets the position to factory settings MOUSE ON buiton Mouse emulation mode starts See page 22 When menu are open or blank screen is displayed or icon of position is displayed there are stopped and back light off TIMER ON OFF button Displays the setting time by count down See page 18 TIMER of menu when you set the minutes of timer When the back light of MENU ON or POSITION ON button on without displaying the icon of POSITION ON or MENU can operate DISK PAD too Displays the icon or MENU at the same time as starting the operation When presses the MOUSE ON button MENU mode or POSITION ON mode is stopped ENGLISH Names and functions of each part continued How to insert batteries Insert the provided batteries LR6 alkal into the remote control transmitter m Remove the battery compartment cover Slide the battery compartment cover in the direction of the arrow while pressing slightly down on it Cautions on use of batteries e Do not use batteries not specified for this unit Also do not use old and new batteries together It may cause a fire injury due to burst of battery or liquid leakage e When inserting batteries pay attention to the direction of the and polarity indications and insert the batte
31. ries correctly If the polarities are confused it may cause injury or damage near the unit due to a burst of battery or liquid leakage 2 Insert the batteries as illustrated inside the battery compartment 3 Replace the cover Cautions on use e Do not drop the remote control transmitter or apply any shock to it e Donot let the remote control transmitter get wet and do not put it on a wet object It may cause a malfunction e If you are not going to use it for a long time remove the batteries from the remote control transmitter e f operation of the remote control becomes difficult reolace the batteries AN Cautions on use of the laser pointer e The laser pointer on the remote control unit radiates the laser beam from the laser aperture e This laser pointer used as a stick for indication Do not stare directly into the laser aperture or radiate the laser beam to other persons as the laser emitted is a dass II laser and it could damage you vision etc Especially pay attention if children are present e The three labels below are caution labels for the laser beam AVOIDE EXPOSURE LASER RADIATION IS EMITTED FROM THIS APERTURE RADIAZIONI LASER C A U T O N NON GUARDARE NEL RAGGIO LUCE APPARECCHIO LASER DI CLASS 2 LASER RADIATION RAYONNEMENT LASER MANUFACTURED NE PAS REGARDER DANS eh erat e 2 LE FAISCEAU APPAREIL August97 WAVE LEGTH 670nm ALASER DE CLASSE 2 MAX OUTPUT 1mW LASER STRAHLUNG NICH
32. rts inside If touched by hand it may result in color unevenness etc 4 Replace the lamp with new one and fix it using the same two screws e Firmly tighten the lamp screws Loose screws may cause bad connection of the connector which in turn may result in malfunctioning 29 ENGLISH 30 Lamp continued 5 Install the lamp cover and fix it using screws e To prevent burn install the lamp cover and secure it using the screws e Do not turn on the power with lamp cover removed Lamp cover e Whenever the lamp is replaced reset the total operation time of the lamp Do not reset if the lamp has not been replaced e Do not perform resetting without changing the lamp as this can cause lamp breakage Screw 2 Reset the lamp time Please carry out the following operation within 10 minutes from power on if you replaced the lamp after 2 000 hours See SJ POSITION ON LASER Eh lai 1 1 Press the RESET button on projector for 3 seconds or remote control TIMER button for 3 seconds and display the total lamp used time e When accumulated operation time of the lamp reaches 1700 hours the lave room following display will appear at the bottom of the screen 2 Press the RESET button on projector or remote control MENU ON button EN gt 0 a during displaying the lamp used time 3 Select the 0 on the screen using the MENU button or DISK PAD Message table On screen display
33. s completed the word lt AUTO gt will disappear The auto adjustment of the white level is cancelled by input switching and signal mode change AUTO e When start up screen is displayed NO INPUT IS DETECTED or SYNC IS OUT OF RANGE is displayed SETUP menu items other than VOLUME cannot be set e TINT cannot be adjusted with PAL SECAM video signal input e TINT COLOR and SHARPNESS cannot be adjusted with an RGB signal input e V POSIT H POSIT H PHASE and H SIZE cannot be adjusted with a VIDEO signal input e Auto adjustment will take about 10 to 15 seconds to complete e n some cases auto adjustment may not function normally depending on the type of computer to which the unit is connected and the signal sent e Auto adjustment may not perform normally with some images Do not use with animated or dark images e Carry out the auto adjustment when the application which is activated on the computer is set to the maximum display e After auto adjustment the screen may become slightly dark due to the auto adjustment of the signal level e Auto adjust can not be performed during freeze during magnify or during the initial screen display NO INPUT IS DETECTED or SYNC IS OUT OF RANGE INPUT The menu INPUT serves for the selection of input source SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT SYSTEM DO RGBI O RGBI E RGB2 O RGB2 DO VIDEO gt E VIDEO gt PAL M PAL Adjustment Item Details of adju
34. stment RGB1 Selects the RGB 1 terminal RGB2 Selects the RGB 2 terminal VIDEO Selects the VIDEO terminal Selects the video signal systems In normal circumstances select AUTO AUTO does not support N PAL When the picture Video is abnormal no color selects the input signal mode NTSC PAL SECAM NTSC4 43 M PAL and N PAL To input N PAL signals select N PAL SYSTEM 17 Adjustments and functions continued The menu IMAGE serves of the picture inversion SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT MIRROR gt MIRROR E NORMAL BLANK D WHITE BLANK gt OH INVERT E BLUE REVEAL DO V INVERT BLACK MESSAGE _ gt O Hav INVERT SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT REVEAL Ml FAST MESSAGE M_ TURN ON o ft DO TURN OFF D MEDIUM O v D stow Adjustment Item Details of adjustment Inverts the picture horizontally or vertically NORMAL Not invert MIRROR H INVERT Inverts the picture horizontally H INVERT Inverts the picture vertically H amp V INVERT Inverts the picture horizontally and vertically BLANK Selects the blank color of signal See page 9 BLANK ON button When start up screen is displayed screen will blank out 5 minutes later REVEAL Selects the speed or revelation See page 9 BLANK ON button Turn off the on screen message VOLUME Input selection display The menu OPT allows you to con
35. t Especially pay attention if children are present If you do the unit may fall over or may be broken causing an injury e Donot put a heavy object on this unit If you do the unit may fall due to its imbalance or it may drop causing an injury E Do not block the ventilation holes Do not block the ventilation holes If the ventilation holes are blocked the heat inside may build up and it may cause a fire Do not use this unit in the following ways On its side Ina poorly ventilated narrow place On a carpet or bedspread Covered with a tablecloth Place this unit so that the ventilation holes are kept 50cm or more away from the wall Pull out the power plug from the power outlet E Cleaning Be sure to pull out the power plug from the power outlet for safety when cleaning E Set the caster stoppers When this unit is installed on the table with casters set the caster stoppers If the table moves it may fall over causing an injury E Do not place this unit in a moist or dusty place e Dono place this unit in a moist or dusty place It may cause a fire electric shock etc e Do not place this unit where it would be exposed to soot or steam near a cooking stove or humidifier etc It S may cause a fire electric shock etc E Handle the power cord carefully e Do not bring the power cord near a heating device The shield of the cord may melt and it may cause a fire electric shock etc e Do not insert disco
36. t item to return to the initial setting 2 Press the RESET button 15 16 Adjustments and functions continued SET U P The menu SET UP serves for the change of parameters influencing the picture and for the move picture position RGB signal input VIDEO signal input SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT VOLUME BRIGHT VOLUME E CONTRAST BRIGHT N OO V POSIT CONTRAST O O H POSIT H PHASE SHARPNESS COLOR i TINT Le COLORBAL RZ B Adjustment Item Details of adjustment VOLUME Decrease _ Increase BRIGHT CONTRAST Lower lt gt Higher H SIZE COLOR BAL Soft lt gt Sharp COLOR Less More TINT Red Green V POSIT V POSITION a os e Widens of Narrow the horizontal size of the picture Or automatic control How to use the SET UP menu 1 Bar display items VOLUME BRIGHT etc Move the green cursor to the item you wish to adjust then move the MENU buttons on the unit or the DISK PAD to left and right to adjust the length of the bar display Some items can not be adjusted during freeze or during magnify Please refer to the above table 2 Numerical display items V POSIT H POSIT etc Use either manual operation or auto adjustment Some items can not be adjusted during freeze or during magnify Please refer to the above table Moves the picture up or down Or automatic control x x x
37. ter inside the unit it may cause a fire electric shock etc E Do not use power supplies other than that specified Do not use this unit with a power SO voltage other than specified power supply voltage It may cause a fire electric shock etc AWarning E Be careful in handling the power cord e Do not scratch damage or process the power cord Do not bend it forcibly Also do not put a heavy object on it do not heat it and do not pull it If you do the power cord may be damaged and it may cause a fire electric shock etc Do not pull the cord Do not put a heavy object on it Do not damage the cord Do not put it near a heating S device e Be careful that this unit is not placed on the power cord The power cord may be damaged and it may cause a fire electric shock etc If the cord is covered with a carpet etc a heavy object may be put on it without your realizing it e f the cord is damaged core wire is exposed disconnected etc ask your dealer to replace it It may cause a fire electric shock etc e Check that no dirt adheres to the power plug and fully insert without any play If dirt adheres or the connection is incomplete it may cause a fire electric shock etc ENGLISH e The outer shield of power cord must be connected to ground If you do not it may cause a electric shock Caution E Do not step on this unit or do not puta heavy object on it e Donot step on this uni
38. trol communication function etc SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT COM SPEED gt COM SPEED ml 1200 COM BITS W 7N1 nN COM BITS gt bps O 2400 O 8N TIMER 15 min TIMER gt DO 4800 a LANGUAGE gt 9600 AUTO OFF gt DO 19200 STARTUP gt SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT SETUP INPUT IMAGE OPT LANGUAGE ENGLISH p STARTUP TE TURNON HO FRAN AIS y CO DEUTSCH AUTO OFF 0 min TURN OFF O ESPA OL STOP HO ITALIANO O NORSK CO NEDERLANDS Adjustment Item Details of adjustment COM SPEED iA AS COMMUNICATION SPEED Selects the data speed of transmission five kinds COM BITS Selects the data format or transmission 7N1 7 data bits No parity 1 stop bit COMMUNICATION BITS 5411 8 data bits No parity 1 stop bit TIMER Sets the minutes of timer 0 99 Selects the language on screen menu ARRE English Fran ais Deutsch Espa ol Italiano Norsk Nederlands AUTO OFF Sets time minutes from the start of displaying start up screen No input is detected or sync is out of range to turning the power OFF 0 is stop and another 1 99 START UP Sets releases start up screen displayed when power is turned on or when no input is detected or sync is out of range Connection to the video signal terminals 1 Input signal Luminance signal 1 0Vp
39. where it gets hot Be careful since if you place the unit outdoors in a place exposed to direct sunlight or near a heating device the cabinet and parts could be affected E Volume Use at the proper volume level so that it does not bother persons in the neighborhood Especially since the sound is likely to carry well at the night even at a low volume consider the neighborhood to a good living environment E Cleaning the lens To clean the lens use a generally available lens cleaning tissue used for cleaning lens of camera glasses etc Be careful not to scratch the lens with a hard object E Cleaning the cabinet e Since many plastic materials are used on the surface of the cabinet if the surface is cleaned using benzene thinner etc it may change in quality or the coating may be peeled off Avoid using chemicals e When a chemically teated cloth is used follow the cautions that come with the cloth e Donot spray a volatile agent such as insecticide on the unit Do not leave a rubber or vinyl object touching the cabinet for a long time It may cause the cabinet to change in quality or the coating to peel off e Clean the dirt from the cabinet and operation panel by dusting lightly with a soft cloth If the dirt is conspicuous wipe off with a cloth moistened with detergent diluted with water then wipe off with a dry soft cloth E Rest your eyes occasionally when viewing for a long time Contents of shipping
40. wo years Ask your dealer to clean inside the unit at least once two years If the unit is left with too much dust inside as it is for along this without cleaning it may cause a fire Especially it is effective to clean before the rainy season starts Consult your dealer for the cost of the cleaning the inside the unit General cautions E Caution when replacing the lamp e When replacing the lamp turn off the power of the projector and disconnect the power plug from the power outlet Then wait for 45 minutes to allow the lamp cool Failure to do so could result ina g burn e For disposal of used lamp treat Pull out the according to the instruction of power plug community authorities from the e Since the lamp is made of glass do PY not apply shock to it and do not scratch it e Also do not use old lamp This could also cause explosion of the lamp e f it is probable that the lamp has exploded explosive sound is heard disconnect the power plug from the power outlet and ask your dealer to replace lamp The lamp is covered by front glass and air tight structure but in rare cases the reflector and the inside of the projector may be damaged by scattered broken pieces of glass and broken pieces could cause injury when being handled e When the lamp has been replaced reset the accumulated operation time of the lamp Do not reset if the lamp has not been replaced Reflector E Do not place this unit
41. y power off for 45 F a minutes Lights red Lights red Goes off Lamp cannot light 2 If the indicator is still it lamp may be defective Replace Lamp is not inserted or the See insert the lamp or close the Lights red Blinks red Cooling fan accidented Calla maintenance person a maintenance Calla maintenance person Accumulated lamp operation Replace lamp and reset the Blinks red Blinks red Goes off time has exceeded 2 000 accumulated lamp operation time hours See page 29 30 When the LAMP indicator lights turn the power off If the problem cannot be recovered contact your dealer 1 When the suction fan is stopped and the inside becomes hot the power is cut automatically for cooling The indicator light will go out In this case turn off the power switch and allow the unit to cool down before turning the power switch on again The lamp will light If the lamp does not light because it is still automatically turned off contact your dealer 2 If temperature inside the unit increases because of blocked vets the lamp may go off for protection and the LAMP indicator will turn red Should this happen turn off the main switch wait until the set cools down about 45 minutes then again turn on the main switch When you think something wrong Check the following again before asking for service If the trouble cannot be recovered consult your dealer heck poini eThe Main power is not turned on leTurn the MA
Download Pdf Manuals
Related Search