Home

Bosch WZ45 User's Manual

image

Contents

1. Integrated IR Dome Camera Safety en 7 housing for servicing and or other activities use this all pole switch as the main disconnect device for switching off the voltage to the unit Camera grounding For mounting the camera in potentially damp environments ensure to ground the system using the ground connection of the power supply connector Camera signal Protect the cable with a primary protector if the camera signal is beyond 140 feet in accordance with NEC800 CEC Section 60 Coax grounding Ground the cable system if connecting an outside cable system to the unit Connect outdoor equipment to the unit s inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source Disconnect the unit s input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal Follow proper safety precautions such as grounding for any outdoor device connected to this unit U S A models only Section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to grounding electrodes and requirements for the grounding electrode Disposal Your Bosch product was developed and manufactured with
2. F 1 Power cable Video cable UTP cable Select a mounting surface that is strong enough to support the camera Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 18 en Installation and Connections Integrated IR Dome Camera 2 10 Use the supplied security tool to remove the four 4 mounting screws B of the dome ring A Align the supplied mounting template with the selected mounting surface Mark the locations of the screw holes and the cable hole on the mounting surface See Figure Drill holes for the mounting screws Drill a hole 1 inch 25 mm in diameter for routing the cables Note Alternately you can route the cables through the 0 5 inch NTP cable entry at the side Route the power cable E and the video cable F or UTP cable F from the camera base through the cable hole in the surface or out of the NTP cable entry at the side Align the four 4 screw holes in the camera base with the screw holes on the mounting surface and then fasten the four 4 mounting screws through the camera base into the mounting surface Adjust the camera settings as describe in Section 4 Tighten the mounting screws B to secure the dome ring A to the camera base D Ensure that the rubber ring between the lens and the dome cover is in place and that it forms a tight seal against the inside of the dome 3 2 Connections CAUTION To ensure reliable ope
3. LXR CCD with mechanical filter The camera can be installed easily in most indoor and outdoor locations Features include Day night mode automatic photocell controlled Privacy masking Even distribution infrared LED array with 30 LEDs Operates at temperature range from 10 C to 55 C 14 F to 131 F at up to 90 humidity non condensing IP66 rating 2 2 Parts Included Quantity Item 1 WZ45 Integrated IR Dome camera Hex key Mounting screws Adapter cable 1 4 1 1 Installation Manual Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 16 en Installation and Connections Integrated IR Dome Camera 3 3 1 Installation and Connections Installation WARNING To prevent injury this apparatus must be securely attached to the floor wall in accordance with the following installation instructions CAUTION To prevent humidity problems the camera must be installed in dry conditions Removing the dome in a wet or humid environment may result in condensation on the dome CAUTION In USA and Canada use Class 2 power supply only TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Installation and Connections en 17 Installation Video Cable Installation UTP cable Letter Description A Dome ring B Dome C Mounting screws D Camera base E
4. IRE at Color Min Illumination 0 001 Lux F1 2 30 IRE at B amp W O Lux with infrared on Gamma 0 45 Sync System Internal External Mechanical Dimension 98mm x 202mm L Weight 1 7kg 3 8lbs Construction Robust aluminum extrusion Finish Anodized silver Camera Pan Tilt Range Pan 360 total Tilt 90 total Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 32 en Technical Specifications Integrated IR Dome Camera Environmental Rating IP66 Operating Temperature 10 C to 55 C 14 F to 131 F Storage Temperature 20 C to 70 C 4 F to 158 F Operating Humidity under 90 non condensing TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Technical Specifications en 33 Dimensions Below are several dimensional drawings of the camera Unit of measure is mm Figure 7 1 Bottom view Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 34 en Technical Specifications Integrated IR Dome Camera 478 Figure 7 2 Side view TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Bosch Security Systems Inc 850 Greenfield Road Lancaster PA 17601 U S A www boschsecurity com Bosch Security Systems Inc 2011
5. module and adjust until desired image is obtained 5 Fasten the focus and zoom adjustment screws to fixate these settings 6 Fasten the three cross head screws to fixate the camera position NOTICE Do not pan or rotate beyond 360 and do not tilt beyond 70 as shown in Figure 4 3 Figure 4 4 and Figure 4 5 above Do not apply excessive force when adjusting the camera positioning TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera On Screen Menu en 23 5 5 1 5 1 1 On Screen Menu OSD Menu DEBRE Exposure Color Day Night Function Motion Privacy Set Exit Exposure Submenu This menu allows you to set and adjust the lens functions TS EXPO LENS MANUAL DC E SHUTTER AUTO 1 100000 BLC AGC OFF 36dB MANUAL DC A setting for switching between manual and DC operation of the lens E SHUTTER Electronic Shutter A function that allows you to set the shutter speed from 1 60 50 to 1 100K BLC Backlight Compensation A function for overcoming compensating for the light behind the object of interest in a scene BLC selectively amplifies parts of the image to compensate for large contrast differences when part of the image is very brightly lit for example a person in a sunlit doorway AGC Automatic Gain Control A function for regulating the gain or amplific
6. power and lightning conductors and transient protection must be in accordance with NEC725 and NEC800 CEC Rule 16 224 and CEC Section 60 Permanently connected equipment Incorporate a readily accessible disconnect device external to the equipment Pluggable equipment Install the socket outlet near the equipment so it is easily accessible Power resupply If the unit is forced to power down due to exceeding the specified operating temperatures disconnect the power cord wait for at least 30 seconds and then reconnect the power cord Power lines Do not locate the camera near overhead power lines power circuits or electrical lights nor where it may contact such power lines circuits or lights SELV All the input output ports are Safety Extra Low Voltage SELV circuits SELV circuits should only be connected to other SELV circuits Because the ISDN circuits are treated like telephone network voltage avoid connecting the SELV circuit to the Telephone Network Voltage TNV circuits System ground Safety ground TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Safety en 9 System video ground is indicated by the symbol The system ground is only used to comply with safety standards or installation practices in certain countries Bosch does not recommend connecting system ground to safety ground unless it is explicitly required However if the system ground and sa
7. rale des communications des tats Unis FCC et en vertu de la norme CES 003 d Industrie Canada Ces exigences visent fournir une protection raisonnable contre les interf rences nuisibles lorsque l appareil est utilis dans le cadre d une installation r sidentielle Cet appareil g n re utilise et met de l nergie de radiofr quences et peut en cas d installation ou d utilisation non conforme aux instructions engendrer des interf rences nuisibles au niveau des radiocommunications Toutefois rien ne garantit l absence d interf rences dans une installation particuli re Il est possible de d terminer la TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Safety en 11 production d interf rences en mettant l appareil successivement hors et sous tension tout en contr lant la r ception radio ou t l vision L utilisateur peut parvenir liminer les interf rences ventuelles en prenant une ou plusieurs des mesures suivantes Modifier l orientation ou l emplacement de l antenne r ceptrice loigner l appareil du r cepteur Brancher l appareil sur une prise situ e sur un circuit diff rent de celui du r cepteur Consulter le revendeur ou un technicien qualifi en radio t l vision pour obtenir de l aide Toute modification apport e au produit non express ment approuv e par la partie responsable de l appareil est strictement interd
8. transportation or handling or if the original identification markings on the product have been removed defaced or altered lightning electricity water fire environment or other hazard or act of God or other impact outside of normal operating guidelines The foregoing warranty is subject to Buyer s i promptly written claim and ii timely provision to BOSCH Security Systems of an opportunity to inspect and test the Product claimed to be defective Such inspection may be on Buyer s premises and or BOSCH Security Systems may request the return of the Product at Buyer s expense However BOSCH Security Systems shall not be responsible for packing inspection or labor costs in connection with the return of Product No Product shall be accepted for warranty service that is not accompanied by a Return Authorization issued by BOSCH Security Systems The liability of BOSCH Security Systems hereunder or otherwise is solely and exclusively limited to replacement new or refurbished Product repair or credit of the amortized purchase price as BOSCH Security Systems may elect for any Product which is returned by Buyer during the applicable warranty period or services for which timely notice of defect has been given by Buyer and which are found by BOSCH Security Systems to be subject to adjustment under this warranty BOSCH Security Systems warranty shall not be enlarged diminished or affected by and no obligation or liability sh
9. Integrated IR Dome Camera W245 BOSCH n Installation Manual Integrated IR Dome Camera Table of Contents en 3 Table of Contents 1 Safety 5 Li Safety Precautions 5 122 Important Safety Instructions 5 1 3 Important Notices 6 14 FCC amp ICES compliance 9 1 5 Warranty Limitation of Liability 12 1 6 Contact Information 14 2 Introduction 15 2 1 Description 15 2 2 Parts Included 15 3 Installation and Connections 16 3 1 Installation 16 3 2 Connections 18 4 Camera Adjustments 20 4 1 Adjusting the pan tilt and focus zoom settings 20 5 On Screen Menu 23 5 1 OSD Menu 23 5 1 1 Exposure Submenu 23 5 1 2 Color Submenu 24 5 18 Day Night Submenu 24 5 1 4 Function Submenu 25 5 1 5 Motion Submenu 26 5 1 6 Privacy Submenu 27 5 1 7 Setup Submenu 28 5 1 8 Exit Submenu 28 6 Troubleshooting 30 6 1 Troubleshooting 30 Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 4 en Table of Contents Integrated IR Dome Camera 7 Technical Specifications 31 TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Safety en 5 1 1 A Safety Safety Precautions DANGER High risk This symbol indicates an imminently hazardous situation such as Dangerous Voltage inside the product If not avoided this will result in an electrical shock serious bodily injury or death WARNING Medium risk Indicates a potentia
10. all arise or grow out of BOSCH Security Systems rendering or technical advice facilities or services in connection with Buyer s order to the products furnished hereunder For more information about the warranty on this product see the Warranty Repair section on Bosch s Customer Care web page at www boschsecurity us en us Service CustomerCare Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 14 en Safety Integrated IR Dome Camera NOTICE Do not remove the serial sticker for the warranty service Doing so will void the warranty 1 6 Contact Information Americas Bosch Security Systems Inc 130 Perinton Parkway Fairport New York 14450 USA Phone 1 800 289 0096 Fax 1 585 223 9180 security sales us bosch com www boschsecurity us Europe Middle East Africa Bosch Security Systems B V P O Box 80002 5600 JB Eindhoven The Netherlands Phone 31 40 2577 284 Fax 31 40 2577 330 emea securitysystems bosch com www boschsecurity com Asia Pacific Robert Bosch SEA Pte Ltd Security Systems 11 Bishan Street 21 Singapore 573943 Phone 65 6258 5511 Fax 65 6571 2698 apr securitysystems bosch com www boschsecurity asia TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Introduction en 15 2 Introduction 2 1 Description The WZ45 Integrated IR Dome camera is a night vision DSP color CCD camera with 1 3 in
11. ation as the light level decreases and the lens opens fully Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 24 en On Screen Menu Integrated IR Dome Camera 5 1 2 5 1 3 Color Submenu This menu allows you to control and adjust the RGB level for the camera to represent accurate white color WB MODE AWC ATW MANUAL PUSH LOCK WB MODE White Balance Mode AWC Auto White Balance A function that allows a color camera to adjust its output color automatically to give a natural color independent of the lighting used ATW Auto Tracking White balance A function that allows the camera to adjust white balance constantly for optimal color reproduction MANUAL A function that allows manual adjustment of the white balance PUSH LOCK A function that enables you to set up automatically readjusted only at the request of the user Day Night Submenu This menu allows you to set the day night mode in order to adjust the output image depending on the light levels D amp N MODE AUTO COLOR B W TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera On Screen Menu en 25 5 1 4 AUTO In this mode the camera output switches automatically between color and day night modes depending on light levels COLOR In this mode the camera output is only in color B W In this mode the camera outpu
12. e 5 1 Set Motion Detection area ALL SET Set the entire screen for movement detection ALL CLEAR Clear the entire screen for movement detection SENSITI Sensitivity level As the sensitivity level increases smaller movements are detected SHOW INDI The motion detected indicator can be selected as icon trace or off TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera On Screen Menu en 27 DELAY OUT The alarm signal display on the screen is delayed from 1 second to 15 seconds 5 1 6 Privacy Submenu This menu allows you to set and adjust the privacy functions that prevent the camera from viewing parts of the scene PRIY MASK 1 SET WINDOW MASK 2 SET WINDOW MASK 3 SET WINDOW MASK 4 SET WINDOW COLOR SET MASK 1 MASK 4 These are the four 4 mask areas that you can set COLOR SET A function that enables you to select the color of the masking cells Figure 5 2 Privacy Mask If SET WINDOW is selected the cell appears on the screen To adjust the cell move the joystick UP DOWN RIGHT LEFT Once you have selected the desired privacy mask area press the joystick in until the mask area is black and then move the joystick any direction to return to the previous screen Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 28 en On Screen Menu Integrated IR Dome Camera 5 1 7 Setup Submen
13. fety ground are connected and grounding loops are causing interference in the video signal use an isolation transformer available separately from Bosch CAUTION Connecting System ground to Safety ground may result in ground loops that can disrupt the CCTV system Video loss Video loss is inherent to digital video recording therefore Bosch Security Systems cannot be held liable for any damage that results from missing video information To minimize the risk of lost digital information Bosch Security Systems recommends multiple redundant recording systems and a procedure to back up all analog and digital information 1 4 FCC amp ICES compliance FCC Information U S A and Canadian Models Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try Bosch Security Sys
14. high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their z working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 2002 96 EC Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 8 en Safety Integrated IR Dome Camera Electronic Surveillance This device is intended for use in public areas only U S federal law strictly prohibits surreptitious recording of oral communications Environmental statement Bosch has a strong commitment towards the environment This unit has been designed to respect the environment as much as possible Electrostatic sensitive device Use proper CMOS MOS FET handling precautions to avoid electrostatic discharge NOTE Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostatic sensitive printed circuit boards Fuse rating For protection of the device the branch circuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC800 CEC Section 60 Outdoor signals The installation for outdoor signals especially regarding clearance from
15. ite Une telle modification est susceptible d entra ner la r vocation du droit d utilisation de l appareil La brochure suivante publi e par la Commission f d rale des communications FCC peut s av rer utile How to Identify and Resolve Radio TV Interference Problems Comment identifier et r soudre les probl mes d interf rences de radio et de t l vision Cette brochure est disponible aupr s du U S Government Printing Office Washington DC 20402 tats Unis sous la r f rence n 004 000 00345 4 CE Information NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to EU Standard EN55022 In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Precautions Do not modify Do not put objects inside the unit Make sure that no metal objects or flammable substances enter the camera This may cause fire short circuits and other damages Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 12 en Safety Integrated IR Dome Camera Be careful when handling the unit To prevent damage do not drop the camera or subject it to strong shock or vibration Install the camera away from electric or magnetic fields Protect the camera from humidity and dust Do not subject the unit to high temperature Be careful when installing close t
16. lly hazardous situation If not avoided this could result in minor or moderate bodily injury CAUTION Low risk Indicates a potentially hazardous situation If not avoided this could result in property damage or risk of damage to the unit 1 Important Safety Instructions PP ie D CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Read follow and retain all of the following safety instructions Heed all warnings on the unit and in the operating instructions before operating the unit Read these instructions Keep this instruction Heed all warnings Follow all instructions Do not use this apparatus near water Clean inside only with dry cloth DOH Be e Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 6 enlSafety Integrated IR Dome Camera 7 Do not block any ventilation openings Install in accordance with manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third groundi
17. ng prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the power where they exit from the apparatus 11 Use only attachments accessories specified by the manufacturer 12 Unplug this apparatus during lightning storms or when unused for long periods of time 13 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 1 3 Important Notices Accessories Do not place this unit on an unstable stand tripod bracket or mount The unit may fall causing serious injury and or serious damage to the unit Quick stops excessive force or uneven surfaces may cause the cart unit combination to overturn Mount the unit per the manufacturer s instructions All pole power switch Incorporate an all pole power switch with a contact separation of at least 3 mm in each pole into the electrical installation of the building If it is needed to open the TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc
18. o ceilings in a kitchen or a boiler room as heat rises and will affect the camera Dirt can be removed from the exterior of the camera by wiping it with a clean soft moistened cloth and soft detergent solution The mounting surface material must be strong enough to secure the camera NOTICE This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 1 5 Warranty Limitation of Liability The WZ45 Integrated IR Day Night Dome Camera has a three year warranty BOSCH Security Systems warrants that its products at the time of shipment by BOSCH Security Systems are free from defect in material or workmanship under normal use and service for the respective warranty periods specified in the applicable Price Schedule or as otherwise published To assure conformance with operating limitations Buyer should refer to the applicable data sheet The warranty is void i if the Product is not operated in conformance with installation environmental mechanical or electrical requirements or within thermal stress limits or ii to the extent that any malfunction is the result of misuse abuse vandalism neglect improper installation or application TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Safety en 13 alteration accident or negligence in use storage
19. ration in wet or moist conditions the cable leads should be sealed once connected TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Installation and Connections en 19 DC12V AC24V Figure 3 1 Connections with video cable ute Figure 3 2 Connections with UTP cable NOTICE When using a 12 VDC power supply check for polarity Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 20 en Camera Adjustments Integrated IR Dome Camera 4 Camera Adjustments 4 1 Adjusting the pan tilt and focus zoom settings Figure 4 1 Pan adjustment Figure 4 2 Tilt adjustment TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Camera Adjustments en 21 Figure 4 4 Maximum tilt angle of 70 degrees Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 22 en Camera Adjustments Integrated IR Dome Camera Figure 4 5 Maximum tilt angle of 70 degrees Follow these steps to adjust pan tilt and focus zoom settings 1 Loosen the 2 cross head screws that secure the pan position of the camera 2 Loosen the cross head screw that secures the tilt position of the camera 3 Adjust the pan 360 tilt 70 and rotate as necessary 4 To adjust the focus and zoom settings loosen the focus and zoom adjustment screws located on the camera
20. shooting Integrated IR Dome Camera 6 Troubleshooting 6 1 Troubleshooting Before sending the camera out for repair check the items below If the problem persists after checking these items contact your service center If no image appears verify that The coaxial cable is attached securely The power and voltage are normal The iris of the lens inside the camera was adjusted correctly with the level volume There is adequate illumination If the image is unclear verify that The lens is in focus The lens is not dirty Dirt or fingerprints on the lens can adversely affect the images Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid available commercially The monitor is adjusted correctly TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera Technical Specifications en 31 7 Technical Specifications Electrical Power 12 VDC 10 16V consumption 24 VAC 20 28V with LED on DC Max 6 7 W AC Max 8 W Video Signal Format NTSC PAL CCD Type 1 3 410 K Pixels 1 3 470 K Color Pixels Color Horizontal 520 TVL Color 560 TVL B amp W Resolution Total Pixels 811 x 508 795 x 596 Lens IR corrected varifocal 5 50 mm Signal to Noise gt 48 50 dB with AGC off Ratio Sensitivity 0 1 Lux F1 2 30
21. t is only in black and white Function Submenu This menu allows you to set and adjust the various camera functions MIRROR SHARPNESS GAMMA SET LEVEL HME SET LEVEL MIRROR A function that enables you to set up reversed LEFT and RIGHT images SHARPNESS A function that enables you to set up sharpness control GAMMA A function that enables you to set up compensation according to gamma value SLC Side Light Compensation Select this mode when the corner of the screen is darker than the center As the level increases the image becomes brighter HME Highlight Masking Exposure This function masks the bright areas on the screen As the level of HME is increased the masking area increases DRC Dynamic Range Compensation This function is to compensate darker images when different exposures are in one scene Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 26 en On Screen Menu Integrated IR Dome Camera 5 1 5 Motion Submenu This menu allows you to set the parameters for the camera to monitor the movement of the image in 64 different areas of the screen and trigger an alarm that appears on the screen ALARM SET WINDOW ALL SET ALL CLEAR SENSITI SHOW INDI DELAY OUT SET WINDOW With the joystick select or deselect areas where you want to detect motion Only areas in blue are monitored for movement the others are ignored masked Figur
22. tems Inc Installation Manual TBD 2 0 2010 12 10 en Safety Integrated IR Dome Camera to correct the interference by one or more of the following measures Fit Ferrite beads on all cable to and from the power supply box within the box walls Route the composite cable between the camera and the power supply in steel conduit piping over the entire run of the cable up to and including connection to a deep conduit base fitted under the camera and a conduit fitting adaptor in the wall of the PSU box Consult a Bosch Service Center for further advice Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 Informations FCC et ICES mod les utilis s aux Etats Unis et au Canada uniquement Suite a diff rents tests cet appareil s est r v l conforme aux exigences impos es aux appareils num riques de classe B en vertu de la section 15 du r glement de la Commission f d
23. u This menu allows you to set miscellaneous parameters for the OSD such as camera ID language etc SET CAMERA ID TITLE EDIT TITLE RESET TITLE POSITION DPC SET WHITE THR BLACK THR DPC LEVEL LANGUAGE ENG CHA PC CONT CAMERA ID This is where you set the ID title of the camera TITLE EDIT This is where you select the value for the camera title TITLE RESET This is where you clear the value of the camera title TITLE POSITION This is where you select the area to display the title DPC SET Defect Pixel Cancellation Set This function automatically removes dead pixels in real time LANGUAGE This is where you set the language English Chinese PC CONT This function enables you to set PC communication by selecting ON 5 1 8 Exit Submenu This menu allows you to exit the OSD menu with or without saving your settings TBD 2 0 2010 12 Installation Manual Bosch Security Systems Inc Integrated IR Dome Camera On Screen Menu en 29 EXIT EXIT SAVE amp EXIT FACTORY SET EXIT Exit the OSD menu SAVE amp EXIT Save your settings and then exit the OSD menu FACTORY SET Restore the factory defaults of the OSD menu NOTICE The settings for Lens Day amp Night and ID Title stay the same even after a FACTORY SET Bosch Security Systems Inc Installation Manual TBD 2 0 2010 12 30 en Trouble

Download Pdf Manuals

image

Related Search

Related Contents

Teledyne 4220 Oxygen Equipment User Manual  GT10-LDR Memory loader USER'S MANUAL  Intérêt des images à très haute résolution spatiale pour évaluer le  SERIE “SF 4WD”  Vantec NexStar  Temperature Rise Calculation Software – Tutorial  Lexmark 342n Printer User Manual  postpartum care  using the webcaster  Pratic - Académie d`Orléans  

Copyright © All rights reserved.
Failed to retrieve file