Bolex Paillard H16 Operating Instructions
Contents
1. The BOLEX H 16 Reflex 5 is basically a standard H 16 Reflex camera but modified to accept a 400 ft interchangeable magazine in this way the film capacity is increased fourfold and the camera s potential is now extended further into the professional field N NOAD 11 13 13 14 14 15 16 Description of the H 16 Reflex 5 camera Description of the 400 ft magazine Method of fixing the magazine onto the camera Loading the magazine and the camera with 200 ft spools with 400 ft film on cores Loading the magazine independently Feeding the film into the camera by hand Changing a partially exposed magazine if the exposed portion of the film is to remain in the magazine if the exposed portion of the film is to be removed from the magazine Magazine maintenance Accessories for your equipment Film running times at 24 f p s Description of the H16 Reflex 5 camera PP on oO ON DO 0 Carrying handle Light tight cover plate picture above Retaining clamp for the magazine or cover plate 2 Fork for opening the sprocket guides for cameras not fitted with the slide 9 drawing above Jotter Adapter bracket for the Bolex exposure meter Film path when using the 400 ft magazine Film rollers Slide for opening the sprocket guides Some cameras are fitted with the slide 9 which is used to keep the sprocket guides open f the film is to be loaded or unloaded by hand In this case it is necessary to open the sprocket gui2. on the take up spindle making sure it is pressed fully home and locked on the spindle by the retaining device 10 To tension the film turn the knurled knobs on the feed spindle and the MM take up motor in the direction indicated by the arrows 11 Replace the magazine and camera lids and lock them carefully in place 12 Briefly depress the front button of the MST motor if the knurled knobs turn the film has been loaded correctly NB As the coils of a fully exposed spool can work loose during transport it is advisable to replace the spool in its original container immediately 400 ft film on cores The operations that have to be carried out in a dark room are printed on a brown ground 1 Before starting ensure that the 2 hubs of the magazine are in place on their spindles the footage counter lever is fitted with the large flanged guide roller the two film rollers are in place on the camera spool spindles Pull back the footage counter lever as far as it will go in the direction of the arrow it will remain locked in this position see picture opposite Place the roll of unexposed film on the hub of the spindle making sure not to disturb the layers of film in the roll The motor drives the roll in a clockwise directiom Lower the footage counter lever onto the film making sure that the guide roller fully straddles the film see illustration opposite Insert the end of the film into the light trap in the mag
3. avoided when the magazine is changed be tween two series of exposures 1 Remove the cover plate from the magazine aperture and draw out a small loop of film about 1 long Fix the magazine to the camera and remove the camera lid Open the sprocket guides and keep them open by pushing the slide forwards or by using the small fork fitted behind the jotter for cameras not fitted with a slide see page 3 4 Open the pressure plate of the gate 5 Draw out a loop of film about one and a half times the length of the camera 6 Run the film beneath the upper sprocket then through the gate and then over the lower sprocket 7 With the forefinger press the film against the gate at a and b and make the upper and lower loops as large as possible 8 Close the pressure plate 9 Close the loop formers with the aid of the lever c 10 Hold the film as shown in the illustration and press lightly towards the front of the camera to ensure that the loop formers are well filled At the same time withdraw the slide or the fork which is holding open the sprocket guides 11 For a fraction of a second depress the front button on the MST motor the perforations on the film will engage with the teeth of the sprockets 12 Open the loop formers and depress for an instant the front button of the MST motor to ensure that the film is being transported correctly Important To ensure that the camera is always loaded correctly always
4. azine aperture Pull a few inches of film through into the camera Replace the lid of the magazine and lock it carefully Close the loop formers and then proceed with the automatic loading as described in the instruction manual for the camera Then insert the end of the film into the magazine aperture Place a standard 2 core on the take up spindle as shown in the illustrations opposite Fold the film back about 1 4 from the end end insert it into the slot in the core Turn the core by hand in the direction of the arrows until the film is tensioned The take up spindle is fitted with a clutch which prevents it from turning in the other direction consequently the film cannot unroll accidentally Unblock the spring loaded lever by pulling it gently forward and bring it into contact with the film at the same time ensuring that the guide roller straddles the film correctly Replace the lid of the magazine and lock it carefully If you have a number of magazines they can all be prepared ready for use by loading them in a darkroom The method of loading is basically the same but the loop of film coming out of the magazine aperture should be taken in again to do this turn the knurled tensioning knob on the feed spindle in the direction of the arrow Once the magazine has been loaded do not forget to replace the cover plate over the film y entry aperture This is of course an operation which cannot be
5. camera maintenance see the instruction manual for the camera Metal carrying cases Different metal carrying cases are available amongst them we would like to point out the two following models 1 This carrying case will hold the camera ready for use i e fitted with the MST motor the 400 ft magazine and the MM take up motor a zoom lens and the lt lt Electric H grip in addition the case will hold various small accessories and three coremounted reels of film in their packaging The lid of the case is an airtight fit and will give your equipment full protection against dust and humidity A metal carrying case of similar design but which will hold three magazines without the MM take up motor is also available Film running times at 24 f p s 10 min 10 min 9 min 8 min 7 min 6 min 5 min 4 min 3 min 2 min 1 min 56 sec 1 sec 7 sec 12 sec 17 sec 23 sec 28 sec 33 sec 39 sec 44 sec 49 sec 55 sec The international Paillard network offers you impeccable after sales service in more than 130 countries Wherever you may be you can entrust your equipment to a BOLEX distributor with complete confidence He employs qualified technicians usually trained in the Paillard factories in Switzerland
6. des and keep them in the open position by push ing the slide towards the front of the camera Fig 1 The small fork 4 has the same function but operates from the front see Fig 11 above Description of the 400 ft magazine Bayonet fitting for the MM take up motor Dual scale film footage counter indicating the length of unexposed film remaining in black for 400 ft of film on cores in red for 200 ft spools Light trap Knurled knob for tensioning the film on the feed spindle The arrows indicate the direction in which the knob must be turned to tension the film Jotter Magazine cover catch Magazine sequence number A set of self adhesive tabs numbered from 2 4 is supplied with each magazine 20 21 22 23 24 25 26 Interchangeable guide roller with wide flanges for the 400 ft cores Feed spindle The push button will release the core or the spool Hub for the 400 ft roll of film Lever for indicating amount of unexposed film figure read off on the counter 11 Serial number to be referred to in all correspon dence Chromium plated guide roller in place for 200 ft spool Takes the place of 17 in this instance Hub for the 400 ft roll of film Take up spindle also fitted with a push button for releasing the hub or the spool Spring loaded lever fitted with a flanged guide roller to control the film as it is taken up onto the 400 ft core Cover plate for the film entry aperture to pr
7. follow these instructions carefully If the exposed portion of the film is to remain in the magazine Depress the front button of the MST motor for about three seconds so that the last exposed frame is transported into the magazine and protected from the light Remove the camera lid Open the sprocket guides and keep them openeither with the slide or the small fork 4 Open the pressure plate and remove the film from the gate the upper sprocket and finally the lower sp rocket Hold the film loop outside the camera and press thefront button on the MST motor to take up the loop Remove the MM take up motor from the magazine to do this press the motor into its housing and turn it in the direction of the arrow until it disengages from the bayonet fitting see illustration above Whilst the new magazine is being fitted the motor can be left hanging from its supply cable Fit the new magazine in place and then load thecamera by hand see page 11 If the exposed portion of the film is to be removed from the magazine 1 Proceed in the same manner as described above and with the film cutter cut the film in the middle of the loop situated outside the magazine 2 Depress the front button of the MST motor until the end of the film has been wound onto the take up core 3 Disengage the MM take up motor from the magazine The inside of the magazine should be dusted at regular intervals with a fine anti static brush For
8. otect it from damage and prevent dust from entering The 400 ft magazine is made from re inforced plastic it is light tight even without the cover plate 26 a baffletype light trap is fitted inside the film entry aperture to prevent light entering the magazine The magazine should be handled with care and in particular it should not be knocked or dropped Method of fixing the magazine onto the camera 1 Lift the clamp and remove the light tight cover plate from the camera 2 Remove the cover plate from the magazine film entry aperture and then position this aperture over the camera as shown in the illustration opposite 3 Slip the front lug of the magazine under the front retaining bar of the support The magazine will then clip into place in the housing on the camera Lower the clamp N B The carrying handle can be positioned either to the right or the left of the magazine to suit the user 5 Attach the MM take up motor to the bayonet fitting as shown in the illustration below Press the motor into the fitting and turn it in the direction of the arrow until it locks fully home The connector will then be pointing downwards 6 Insert the plug on the feed cable for the MM take up motor into the upper socket on the MST motor To disconnect press down the small button on the socket and pull the cable out Spools of 200 ft even of 100 ft if the camera is used without a magazine can be loaded in daylight pr
9. oviding sufficient care is taken to avoid direct sunlight when loading the film 1 When the lids of the magazine and the camera have been taken off remove the hubs from the magazine spindles by pressing down the push buttons a and b on the spindles 2 The footage counter lever must be fitted with the guide roller with the chromium plated flanges raise the lever as far as it will go and it will remain locked in this position Place the other guide roller in the clip c 3 The spring loaded lever 25 should remain in its disengaged position 4 Place the spool of unexposed film on the spindle a making sure it is pressed fully home and locked in position by the retaining device on the spindle The motor drives the spool in a clockwise direction 5 Lower the footage counter lever The guide roller will now press against the film see illustration opposite 6 Insert the end of the film into the magazine aperture Pull 3 c the film through into the camera and cut the end with the film cutter 7 Close the loop formers and then proceed with the automatic loading as described in the instruction manual for the camera Allow about 2 ft of film to run through the lower sprocket 8 Insert the end of the film into the magazine aperture and draw the film into the magazine 9 Holding the take up spool in the right hand insert the end of the film into the slot in the spool core Wind the film around the core 2 or 3 times and place the spool
Download Pdf Manuals
Related Search