Black Box LGC200A User's Manual
Contents
1. Two LGC200A with the same SFP modules can be used in pairs NOTE LGC200A could be connected to LGC201A or LGC202A however the SFP module in the LGC200A must use the same mode and wavelength as the opposite end The fiber connectors depend on the type of SFP installed See Table 4 1 724 746 5500 blackbox com Page 19 Chapter 4 Installation Table 4 1 LGC200A LC to LGC201A or LGC202A SC connection Part Number LGC200A LGC201A LGC202A Transmision SFP module 850 nm 1310 nm Media multimode single mode 4 2 Installation Procedure Use a fiber cable to connect two converters and extend a copper link or to connect a 1000BASE FX segment to a 1000BASE X segment on your network 1 Connect a converter to a 1000BASE TX device hub or switch Make sure that the CAT5 twisted pair cable between the 1000BASE TX device and the converter is less than 328 feet 100 meters long e Connect one end of the CATS twisted pair cable to the RJ 45 jack on the convert er and the other end of the cable to the RJ 45 jack on the 1000BASE TX device 2 Connect two converters or a converter and a 1000BASE FX device Use an SC fiber cable to connect the two converters SC connector or the SC connector of a converter and a 1000BASE FX device 3 Turn on the power 4 3 Install the Media Converter into the LHC200A RACK 1 Take out the two screws located on the top of the chassis and use them to install the retainer as2. Chapter 2 Overview 2 Overview 2 1 Introduction The Pure Networking LGC200A LGC201A and LGC202A are Gigabit Media Converters The SFP port of the LGC200A supports hot swappable Gigabit SFP modules The LGC201A has a dual SC multimode fiber connector and the LGC202A has a dual SC single mode fiber connector Use the media converters to join a 1000BASE TX segment to a 1000BASE SX or 1000BASE LX segment on your network or use them in pairs to extend the 328 feet 100 m distance limitation of copper based Ethernet Three converter models are available LGC200A This SFP module media converter transmits receives data based on the SFP module that is installed e LGC201A This fiber SC media converter transmits receives data by 850 nm short wave laser over multimode fiber LGC202A This fiber SC media converter transmits receives data by 1310 nm short wave laser over single mode fiber 2 2 Features Complies with 802 3ab and 802 3z standards Provides 1 SC LC connector or 1 SFP module slot and 1 RJ 45 connector Both TX and FX ports work at 1000 Mbps in full duplex mode Supports Auto MDI MDI X for the TX port Extends fiber distance up to 0 55 kilometers for multimode fiber and 15 kilometers for single mode fiber Easy to view LED indicators provide status to easily monitor network activity Uses a 9 VDC 600 mA external power supply included Page 8 724 746 5500 blackbox com Chapte
3. deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabricante 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor 1
4. 1 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Page 4 724 746 5500 blackbox com NOM Statement 12 13 14 15 16 17 18 Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante En caso de existir una antena externa deber ser localizada lejos de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada 724 746 5500 blackbox com
5. ED 7 1 barrel connector 8 1 switch for the FX port See Table 5 1 for LED functions Description Links to fiber segment Lights ON when there is a valid link Flashing when the converter is receiving or transmitting data from he fiber optic connector OFF when there is no valid link Lights ON when there is a valid link Flashing when the converter is receiving or transmitting data from he twisted pair port OFF when here is no valid link Links to 1000BASE T device Lights ON when power to the chassis is on OFF when power is off Lights ON when the TP port is con nected to 1000BASE TX OFF when he TP port is not connected Links to power Selects Force or Auto negotiation mode 724 746 5500 blackbox com Page 13 Chapter 2 Overview 2 5 3 LGC200A SFP lt BLACK BOX mO Oe uC Qv 1000BASE X 1000BASE T 1 2 3 4 Figure 2 5 Front panel of the LGC200A FORCE TT Auto Figure 2 6 Back panel of the LGC200A Page 14 724 746 5500 blackbox com Chapter 2 Overview Number 1 Table 2 4 LGC200A components Component 1 SFP slot for SFP module 1 FX Link LED 1 TP Link LED 1 RJ 45 connector 1 PWR LED 1 RX LED 1 barrel connector 1 switch for the FX port Description Links to fiber segment Lights ON when there is a valid link Flashing when the converter is receiving or transmitting data from the fiber optic c
6. LGC200A BLA CK BOX LGC201A NETWORK SERVICES LGC202A segment on your netv 100 m distance limit o Customer Order toll free in the U S Call 877 877 BBOX outside U S Support call 724 746 5500 FREE technical support 24 hours a day 7 days Information a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks and Pure Networking is a trademark of BB Technologies Inc Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners Page 2 724 746 5500 blackbox com FCC and IC RFI Statements FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS Class B Digital Device This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation However there is no guarantee that interference will not occur in a particular installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfere
7. Page 5 Table of Contents Table of Contents IS AAA erbe aa c tenet iet ance diete 7 2 Overview 2 1 Introduction 2 2 Features 2 3 What s Included 2 4 Connectors and Network Cables Supported 2 5 Hardware Description 2 5 1 LGC201A 2 5 2 LGC202A 2 5 3 LGC200A 3 COMIQUI Msc 16 Installation 41 Typical Installation 4 1 1 LGC201A and LGC202A 4 1 2 LGC200A 4 2 Installation Procedure 5b S P Chat OM sc ceteri eaaa esha a a Eai aire aii 5 1 LEDs on the Media Converter 5 2 Force Auto Switch 6 Troubleshooting 6 1 Contacting Black Box 6 2 Shipping and Packaging 2b Page 6 724 746 5500 blackbox com Chapter 1 Specifications 1 Specifications Maximum Distance LGC201A Multimode fiber optic 0 55 km LGC202A Single mode fiber optic 15 km Standards IEEE 802 3ab 802 3z Connectors LGC201A 1 dual SC 1 RJ 45 LGC202A 1 dual SC 1 RJ 45 LGC200A Depends on installed SFP module Temperature Tolerance Operating 32 to 4 104 F 0 to 40 C Storage 40 to 4 158 F 40 to 470 C Humidity Operating 10 to 9096 relative humidity noncondensing Storage 5 to 9096 relative humidity noncondensing Power External 100 240 VAC 50 60 Hz 0 3 A Output 9 VDC 0 6 A 5 4 W maximum Size 1 1 H x 3 7 W x 2 9 D 2 7 x 9 4 x 7 4 cm Weight 1 1 Ib 0 5 kg 724 746 5500 blackbox com Page 7
8. ation using one media converter 724 746 5500 blackbox com Page 17 Chapter 4 Installation 4 Installation 4 1 Typical Installation 4 1 1 LGC201A and LGC202A 1 The SC fiber connector of an LGC201A transmits receives data by 850 nm short wave laser on multimode fiber 2 The SC fiber connector of an LGC202A transmits receives data by 1310 nm short wave laser on single mode fiber Figure 4 1 shows a typical installation Device A Twisted pair Twisted pair Device B cable cable LGC201A gg 3 ma LGC201A or a tJ or LGC202A 5 n LGC202A AS Multimode or single mode fiber optic cable Figure 4 1 Transmits and receives data on multimode or single mode fibers NOTE The units work in pairs You have to use either two LGC201A converters or two LGC202A converters Or use two kinds of SFP modules single mode or multimode Page 18 724 746 5500 blackbox com Chapter 4 Installation 4 1 2 LGC200A Plug the SFP module into the LGC200A as shown in Figure 4 2 o 7 O Qu 1ODOBASEX FX TP 1000BASET Figure 4 2 Plug the SFP module into the LGC200A Device A Twisted pair Twisted pair Device B cable cable m m p ma LGC200A LGC200A LGC201A or LGC202A Multimode or single mode fiber optic cable Figure 4 3 Transmits and receives data between two LGC200A converters or one LGC200A and one LGC201A LGC202A NOTE
9. nce to radio communications If this equipment does cause harmful interference to radio or telephone reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult an experienced radio TV technician for help Caution Changes or modifications not expressly approved by the party responsible for com pliance could void the user s authority to operate the equipment To meet FCC requirements shielded cables and power cords are required to con nect this device to a personal computer or other Class B certified device This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de classe B prescrites dans le R glement sur le brouillage radio lectrique publi par Industrie Canada 724 746 5500 blackbox com Page 3 NOM Statement Normas Oficiales Mexicanas NOM Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1 Todas las instrucciones de seguridad y operaci n
10. nel of the LGC201A Page 10 724 746 5500 blackbox com Chapter 2 Overview Number 1 Table 2 2 LGC201A components Component Description 1 dual SC connector TX RX Links to fiber segment Lights ON when there is a valid link Flashing when he converter is receiving 1 FX Link LED or transmitting data from he fiber optic connector OFF when there is no valid ink Lights ON when there is a valid link Flashing when he converter is receiving or transmitting data from he twisted pair port OFF when there is no valid link 1 TP Link LED Links to 1000BASE T 1 RJ 45 connector device Lights ON when power to 1 PWR LED he chassis is on OFF when power is off Lights ON when the TP port is connected to 1 RX LED 1000BASE TX OFF when the TP port is not connected 1 barrel connector Links to power Selects Force or 1 switch for the FX port Auto negotiation mode 724 746 5500 blackbox com Page 11 Chapter 2 Overview See Table 5 1 for LED functions 2 5 2 LGC202A mr O O RX unk Oun 1000BASE LX 1000BASE T 1 2 3 4 Figure 2 3 Front panel of the LGC202A FORCE TT Auto Figure 2 4 Back panel of the LGC202A Page 12 724 746 5500 blackbox com Chapter 2 Overview Table 2 3 LGC202A components Number Component 1 1 dual SC connector TX RX 2 1 FX Link LED 3 1 TP Link LED 4 1 RJ 45 connector 5 1 PWR LED 6 1 RX L
11. onnector OFF when there is no valid link Lights ON when there is a valid link Flashing when the converter is receiving or transmitting data from the twisted pair port OFF when there is no valid link Links to 1000BASE T device Lights ON when power to the chassis is on OFF when power is off Lights ON when the TP port is connected to 1000BASE TX OFF when the TP port is not connected Links to power Selects Force or Auto negotiation mode 724 746 5500 blackbox com Page 15 Chapter 3 Configuration 3 Configuration To expand a Gigabit Ethernet network you can use the converter as described in the following examples 1 Place two converters back to back between the end devices as shown in Figure 3 1 Twisted pair Twisted pair Device A cable cable Device B mem 7 10008ASE TX u 4 interface a LGC201A B i g LGC201A or or LGC202A 1000BASE X yy LGC202A interface Single mode or multimode fiber optic cable Figure 3 1 Application using two converters NOTE Use two LGC201A Media Converters or two LGC202A media converters to expand your network 2 Place one converter directly between a 1000BASE TX network segment and a fiber optic network segment as shown in Figure 3 2 Page 16 724 746 5500 blackbox com Chapter 3 Configuration Device A a 1000BASE TX interface Ti LGC201A o M sii LGC202A LJ WM 1000BASE X 22 interface Figure 3 2 Applic
12. r 2 Overview 2 3 What s Included Your package should contain the following items If anything is missing or damaged contact Black Box Technical Support at 724 746 5500 or info blackbox com 1 Pure Networking Gigabit Media Converter 1 9 VDC 600 mA power adapter This user s manual 2 4 Connectors and Network Cables Supported The connectors and network cables supported by the converter are listed as follows Connectors RJ 45 SC LC e Network Cables CAT5 twisted pair TP 850 nm 62 5 125 um or 50 125 um multimode fiber or 1310 nm 9 125 um single mode fiber Table 2 1 Connectors and network cable supported Output Part Transmission Transmission Center Number Interface Distance Media Wavelength Multimode RJ 45 TP Depends on Depends on LGC200A and fiber SFP used SS SFP used 50 125 um 0 55 km multimode RJ 45 TP iber TP LGC201A and SC 850 nm fiber 62 5 125 um 0 22 km multimode iber TP pou Single mode LGC202A andSC 15 km ng 1310 nm ler iber TP 724 746 5500 blackbox com Page 9 Chapter 2 Overview 2 5 Hardware Description Figures 2 1 through 2 6 show the front and back panels of the media converters Tables 2 2 through 2 4 describe their components 2 5 1 LGC201A mr O O RX unk O 1000BASE SX 1000BASE T lt gt BLACK BOX 1 2 3 4 Figure 2 1 Front panel of the LGC201A FORCE IM auto 7 8 Figure 2 2 Back pa
13. shown in Figure 4 5 Page 20 724 746 5500 blackbox com Chapter 4 Installation Chassis Figure 4 5 Install the retainer 2 Turn off the switch power and take off the front guard that s on the chassis 3 Preconfigure the media converter then insert the media converter into the open slot of the chassis 4 Use the locking knob to lock the media converter tightly in the chassis Chassis Figure 4 6 Installing a media converter into the chassis 724 746 5500 blackbox com Page 21 Chapter 4 Installation 5 Turn on the power switch and you will see the media converter s Power LED light Then you can operate it in the same way as a standalone Pure Networking Media Converter Page 22 724 746 5500 blackbox com Chapter 5 Operation 5 Operation 5 1 LEDs on the Media Converters The converters have real time LED indicators that can provide real time status reports Just look at the LEDs to deterimine the link status Figure 5 1 shows the LEDs and Table 5 1 describes their functions pwr _ O RX us C O LINK FX TP Figure 5 1 LEDs 724 746 5500 blackbox com Page 23 Chapter 5 Operation Name PWR FX Link Link TX RX Table 5 1 LED functions Status ON OFF ON Flashing OFF ON Flashing OFF ON OFF 5 2 Force Auto Switch The DIP switch on the side of the converter sets force or autonegotiation mode FORCE AUTO Description Power to the chas
14. sis is ON Power to the chassis is OFF There is a valid link The converter is receiving or transmitting data from the fiber optic connector There is no valid link There is a valid link The converter is receiving or transmitting data from the TP port There is no connection on the port The TP port is connected to 1000BASE TX The TP port is not connected Figure 5 2 Force Autonegotiation switch In a back to back setup set the two converters that are on opposite ends to Force mode When connected to other products such as switches set the converter to auto negotiation mode Page 24 724 746 5500 blackbox com Chapter 6 Troubleshooting 6 Troubleshooting 6 1 Contacting Black Box If you determine that your Pure Networking Gigabit Media Converter is malfunctioning do not attempt to alter or repair the unit It contains no user serviceable parts Contact Black Box Technical Support at 724 746 5500 or info blackbox com Before you do make a record of the history of the problem We will be able to provide more efficient and accurate assistance if you have a complete description including the nature and duration of the problem when the problem occurs e the components involved in the problem any particular application that when used appears to create the problem or make it worse 6 2 Shipping and Packaging If you need to transport or ship your Pure Networking Gigabit Media Conver
15. ter Package it carefully We recommend that you use the original container e If you are returning the unit make sure you include everything you received with it Before you ship for return or repair contact Black Box to get a Return Authorization RA number 724 746 5500 blackbox com Page 25 NOTES Page 26 724 746 5500 blackbox com NOTES 724 746 5500 blackbox com Page 27 Black Box Tech Support FREE Live 24 7 Tech support the way it should be EN i 1 Great tech support is just 30 seconds away at 724 746 5500 or blackbox com BLACK BOX About Black Box Black Box provides an extensive range of networking and infrastructure products You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free live 24 7 Tech support available in 30 seconds or less O Copyright 2012 Black Box Corporation All rights reserved LGC200A LGC201A LGC202A version 1 724 746 5500 blackbox com
Download Pdf Manuals
Related Search