BENDIX BW7506 User's Manual
Contents
1. smooth and clean Perform the steps outlined in Section 12 Replacing the Service Diaphragm When the service diaphragm service return spring or both are replaced they should also be replaced in the corresponding chamber on the same axle PARKING EMERGENCY Ves s gt amd RELEASE vi SoS ey ah ji A WARNING Staite oane N TA SERVICE ozan TOOL m SIDE POCKET r NNN MOUNTING NUT SERVICE PUSH ROD FIGURE 2 SPRING BRAKE EXTERNAL VIEW MAIN SPRING PARKING EMERGENCY E PORT _ DIAPHRAGM MARKED 12 DIAPHRAGM NON PRESSURE HOUSING PUSH ROD FIGURE 3 SPRING BRAKE CUT AWAY VIEW 4 0 OPERATION amp LEAKAGE TESTS 4 1 OPERATING TEST 4 1 1 Apply the brakes and observe that all the push rods move out promptly and without binding 4 1 2 Release brakes and observe that all the push rods return to the released position promptly and without binding 4 1 3 Check the push rod travel The push rod travel should be as short as possible without the brakes dragging Adjust travel of push rod at the slack adjuster if necessary 4 1 4 Ifthe orange stroke indication mark on the push rod is visible consult the slack adjuster service instructions and verify the proper slack adjuster function 4 2 LEAKAGE TEST 4 2 1 Make and hold a full brake application 4 2 2 Using a soap solution coat the clamping ring s If leakag2. brake lining particles Proper procedures to reduce exposure include working in a well ventilated area segregation of areas where brake work is done use of local filtered ventilation systems or use of enclosed cells with filtered vacuums Respirators approved by the Mine Safety and Health Administration MSHA or National Institute for Occupational Safety and Health NIOSH should be worn at all times during brake servicing e Workers must wash before eating drinking or smoking shower after working and should not wear work clothes home Work clothes should be vacuumed and laundered separately without shaking e OSHA regulations regarding testing disposal of waste and methods of reducing exposure for asbestos are set forth in 29 Code of Federal Regulations 1910 001 These Regulations provide valuable information which can be utilized to reduce exposure to airborne particles e Material Safety Data Sheets on this product as required by OSHA are available from Bendix Call 1 800 247 2725 and speak to the Tech Team or e mail us at techteam bendix com The diaphragm is held between the adapter base and non pressure plate by a two piece clamp ring Different size brake chambers are identified by numbers which specify the effective area of a diaphragm For example a Type 30 30 Spring Brake has 30 square inches of effective area on each diaphragm The standard diaphragm material is a compound of natural rubber with a fabric in
3. by rotating it with respect to the mounting studs as needed 7 0 7 Make sure that the diaphragm is properly aligned and seated See Figure 5 Be sure that the service diaphragm is fully inserted into the clamp 7 0 8 Reinstall the clamp rings and hardware Check the arrangement of the removed actuator and position the hardware with respect to the mounting studs as required Tighten each clamp nut evenly in an alternating pattern Torque each clamp nut to a final torque of 20 30 ft lbs 28 40 Nm 7 0 9 Inspect the clamp ring and hardware for proper seating 7 0 10 Apply up to around 10 psi air pressure to the service port of the spring brake chamber Do not exceed 10 psi Remove the locking pliers from the brake chamber push rod 7 0 11 Perform the Leakage Test 4 2 before returning the spring brake on the vehicle INCORRECT CORRECT FIGURE 5 CORRECT DIAPHRAGM POSITION 8 0 MECHANICAL RELEASE CAGING AND REMOVAL OF THE PIGGYBACK SPRING BRAKE CHAMBER TO BE REPLACED NOTE The spring brake chamber can be replaced with the service brake chamber mounted to the vehicle or removed for ease of access To remove the assembly from the vehicle perform the steps outlined in Step 11 0 Removal and Installation of the Combination Spring Brake A WARNING Do not mechanically release cage the spring if there is any structural damage to the brake Caging the spring in such a chamber may cause serious injury or death Repla
4. 2 0 Safe Maintenance Practices 3 0 Preventive Maintenance 4 0 Operation and Leakage Tests 5 0 Operation General 6 0 Mechanical Release Caging of the Bendix EverSure Spring Brake 7 0 Clocking Rotating the Bendix Service Replacement Spring Brake Chamber 8 0 Mechanical Release Caging and Removal of the Piggyback Spring Brake Chamber to be Replaced 9 0 Installing the Bendix EverSure Piggyback Spring Brake Chamber 10 0 Un Caging the Bendix EverSure Spring Brake Chamber Apply Park Brake 11 0 Removal and Installation of the Combination Spring Brake 12 0 Replacing the Service Diaphragm 2 0 SAFE MAINTENANCE PRACTICES A WARNING PLEASE READ AND FOLLOW THESE INSTRUCTIONS TO AVOID PERSONAL INJURY OR DEATH When working on or around a vehicle the following general precautions should be observed at all times 1 Park the vehicle on a level surface apply the parking brakes and always block the wheels Always wear safety glasses Where specifically directed the parking brakes may have to be released and or spring brakes caged and this will require that the vehicle be prevented from moving by other means for the duration of these tests procedures 2 Stop the engine and remove ignition key when working under or around the vehicle When working in the engine compartment the engine should be shut off and the ignition key should be removed Where circumstances require that the engine be in operation EXTREME
5. 55 ft lbs 80 210 Nm Connect the yoke to the slack adjuster and install the yoke pin and the cotter pin 11 3 4 Connect the air hoses to brake chamber Torque the fitting to 30 ft lbs 40 5 Nm Check to be sure the air hoses are properly supported and clamped if necessary to provide proper clearance including checking for proper length when under full steer conditions 11 3 5 Pressurize the service chamber by putting air into the service port Do not exceed 120 psig 11 3 6 Test for leakage see Section 4 2 Minimal leakage is permitted 100 SCCM 11 3 7 Uncage the main spring and return the release tool into the release tool side pocket see Section 10 11 3 8 Adjust the slack adjuster per manufacturer s recommendations 11 3 9 Check the function and stroke Section 4 1 11 3 10 Replace the dust cap in the keyhole A WARNING Check for proper service and emergency operation after servicing any part of the brake chamber s Check the brake adjustment if the combination spring brake was removed installed Follow the vehicle manufacturer s instructions to adjust the brakes 12 0 REPLACING THE SERVICE DIAPHRAGM See Figure 8 To replace the service diaphragm it is not necessary to remove the complete combination spring brake from the vehicle however it can be removed for ease of access To remove the combination spring brake perform the steps outlined in Step 11 0 Removal and Installation of the Combination Spri
6. CAUTION should be used to prevent personal injury resulting from contact with moving rotating leaking heated or electrically charged components 3 Do not attempt to install remove disassemble or assemble a component until you have read and thoroughly understand the recommended procedures Use only the proper tools and observe all precautions pertaining to use of those tools 4 Ifthe work is being performed on the vehicle s air brake system or any auxiliary pressurized air systems make certain to drain the air pressure from all reservoirs before beginning ANY work on the vehicle If the vehicle is equipped with a Bendix AD IS air dryer system or a dryer reservoir module be sure to drain the purge reservoir 5 Following the vehicle manufacturer s recommended procedures deactivate the electrical system in a manner that safely removes all electrical power from the vehicle 6 Never exceed manufacturer s recommended pressures 7 Never connect or disconnect a hose or line containing pressure it may whip Never remove a component or plug unless you are certain all system pressure has been depleted 8 Use only genuine Bendix brand replacement parts components and kits Replacement hardware tubing hose fittings etc must be of equivalent size type and strength as original equipment and be designed specifically for such applications and systems 9 Components with stripped threads or damaged parts should be repl
7. NE 1 MONTH 3 1 1 See Figure 2 Check push rod travel and adjust travel at the slack adjuster if needed only where manual slack adjusters are used Push rod travel should be as short as possible without the brakes dragging consult the manufacturer s installation instructions for the slack adjuster Excessive push rod travel reduces braking efficiency shortens diaphragm life gives slow braking response and wastes air 3 1 2 Check push rod to slack adjuster alignment from release to full stroke position to be sure the push rod moves out and returns properly without binding at the non pressure plate hole or with other structures Also check the angle formed by the slack adjuster arm and push rod It should be greater than 90 degrees when the chamber is in the released position and approach 90 degrees at maximum readjustment stroke 3 1 3 Check tightness of mounting nuts Torque on the non pressure plate mounting nuts should be 133 155 ft Ibs 3 1 4 Check cotter pins to ensure they are in place 3 1 5 Check all hoses and lines They should be secure and in good condition with sufficient length to allow for axle movement 3 2 EVERY 3 600 OPERATING HOURS 100 000 MILES OR ONE 1 YEAR 3 2 1 Carefully inspect all metal parts for cracks distortion or damage 3 2 2 Perform the Leakage Test 4 2 As necessary install a new diaphragm or any other parts if they are worn or deteriorated All diaphragm sealing surfaces should be
8. NON PRESSURE HOUSING SERVICE RETURN SPRING SERVICE PUSH ROD YOKE Piggyback spring brake components are not serviceable and are shown here for informational purposes only RELEASE SERVICE DUST CAP CHAMBER DUST CAP INSTALLED REMOVED A WARNING SPRING BRAKE CHAMBERS CONTAIN A LOADED COMPRESSION SPRING PROPERTY DAMAGE SERIOUS INJURY OR DEATH MAY OCCUR IF THESE INSTRUCTIONS ARE NOT FOLLOWED COMPLETELY NEVER attempt to remove a spring chamber crimped band Follow all industry safe maintenance practices including those listed on page two of these instructions 1 0 DESCRIPTION The Bendix EverSure spring brake is made up of a conventional brake chamber and an emergency or parking spring mechanism for use on vehicles equipped with cam foundation brakes The spring brake actuator provides 1 service braking 2 parking and 3 emergency braking The actuator can be piped with various system arrangements to be automatically or manually applied under emergency braking conditions The spring brake is a diaphragm type actuator which converts the energy of air pressure into mechanical force wi whe a D CLAMP NON SERVICEABLE SECTION SEALED WITH A CRIMPED BAND NON SERVICEABLE PARKING DIAPHRAGM DIAPHRAGM RELEASE TOOL T BOLT A NON SERVICEABLE NO TOUCH POWER SPRING PARKING EMERGENCY BRAKE HOUSING FIGURE 1 BENDIX EVERSURE SPRING BRAKE Section 1 0 Description
9. aced rather than repaired Do not attempt repairs requiring machining or welding unless specifically stated and approved by the vehicle and component manufacturer 10 Prior to returning the vehicle to service make certain all components and systems are restored to their proper operating condition 11 For vehicles with Automatic Traction Control ATC the ATC function must be disabled ATC indicator lamp should be ON prior to performing any vehicle maintenance where one or more wheels on a drive axle are lifted off the ground and moving A WARNING Not all wheels and valve stems are compatible with Bendix air disc brakes Use only wheels and valve stems approved by the vehicle manufacturer to avoid the risk of valve stem shear and other compatibility issues A WARNING AVOID CREATING DUST POSSIBLE CANCER AND LUNG DISEASE HAZARD While Bendix Spicer Foundation Brake LLC BSFB does not offer asbestos brake linings the long term affects of some non asbestos fibers have not been determined Current Occupational Safety amp Health Administration OSHA regulations cover exposure levels to some components of non asbestos linings but not all The following precautions must be used when handling these materials e Avoid creating dust Compressed air or dry brushing must never be used for cleaning brake assemblies or the work area e Bendix recommends that workers doing brake work must take steps to minimize exposure to airborne
10. amber Check around the edge of the dust plug weather seal to be sure it is firmly seated IMPORTANT Always re install the tethered dust plug weather seal in the spring brake caging tool key hole Failure to do so will result in corrosion and foreign material ingestion through the key hole which may void the warranty Do not use excessive force when installing the dust plug weather seal Extreme force may cause damage and make it unusable Replacement dust plugs can be purchased from your local Bendix distributor A WARNING Check for proper service and emergency operation after servicing any part of the brake chamber s Check the brake adjustment if the combination spring brake was removed installed Follow the vehicle manufac turer s instructions to adjust the brakes 11 0 REMOVAL AND INSTALLATION OF THE COMBINATION SPRING BRAKE 11 1 SERVICE BRAKE CHAMBER REPLACEMENT AND CLOCKING CAUTION Replace the brake chamber with the same type and size as originally installed on the vehicle Replacement with alternate equipment without written authorization from Bendix and the vehicle manufacturer could compromise brake performance Brake chambers can be clocked to ensure the proper alignment of mounting studs drain holes and ports A WARNING Do not mechanically release cage the spring if there is any structural damage to the spring brake chamber Caging the spring in such a chamber may cause seri ous injury or death R
11. ce the complete assembly 8 1 Mechanically release the old spring brake by following the original manufacturer s instructions 8 2 Ensure air pressure is removed from all air reservoirs before removing the air hoses or working on the spring brake 8 3 Remove air hoses from the spring brake chamber Be sure to mark both hoses to ensure proper reinstallation 8 4 Clamp a pair of locking pliers around the service push rod touching the non pressure housing This cages the service return spring 8 5 Remove the clamp nuts and service clamp assembly and carefully remove the old piggyback chamber 8 6 Discard the clamp clamp hardware and diaphragm 9 0 INSTALLING THE BENDIX EVERSURE PIGGYBACK SPRING BRAKE CHAMBER FIGURE 6 PIGGYBACK SPRING BRAKE KIT 9 1 Install new service diaphragm 9 2 Clock chamber See Section 7 0 as necessary 9 3 Line up the new spring brake chamber the service diaphragm and the non pressure housing ensuring that they are centered 9 4 Assemble the service clamp assembly Ensure all parts are seated properly and remain centered See Figure 5 9 5 Torque the clamp nuts to 20 30 ft Ibs Remove the locking pliers from the service push rod 9 6 Connect the emergency air hose to the emergency parking port 12 and reconnect the service air line to the service port 11 Torque fittings to no more than 30 ft lbs 40 Nm 9 7 Pressurize the service half by putting air into the ser
12. d to the service chamber the greater the force applied by the push rod Conversely the less pressure applied to the service chamber the less force applied by the push rod Push rod force is determined by multiplying the delivered air pressure by the effective diaphragm area For example if 60 psi is applied to a Type 30 service chamber the lineal force on the end of the push rod is approximately 1 800 Ibs When air pressure is released from the brake chamber the push rod return spring in combination with the brake shoe return spring returns the diaphragm push plate and rod assembly slack adjuster and brake cam to their released positions releasing the brakes When the driver operates the parking brake air is exhausted from the chamber The main spring is allowed to extend which forces the push rod and the emergency diaphragm forward This forces the service diaphragm and service push rod forward which applies the brakes When the air pressure in the Bendix EverSure Spring Brake chamber drops to below approximately 78 psi the main spring overcomes chamber pressure and forces the push rod and emergency diaphragm forward 6 0 MECHANICAL RELEASE CAGING OF THE BENDIX EVERSURE SPRING BRAKE NOTE The Bendix EverSure Spring Brake Chamber is not shipped caged It must be caged prior to any work being done 6 0 1 This procedure will be made much easier if air pressure 100 120 psi 6 6 8 0 bar is used to collapse t
13. e is detected tighten the clamping ring only enough to stop leakage DO NOT OVERTIGHTEN as this can distort sealing surface or clamping ring Coat the area around the push rod hole loosen boot if applicable Minimal leakage is permitted 100 SCCM If abnormal leakage is detected the diaphragm must be replaced 4 2 3 Using a soap solution check the hose fitting for leakage A one inch bubble in one minute is acceptable 5 0 OPERATION GENERAL The Bendix EverSure Spring Brake is made up of the service chamber and the piggyback spring brake chamber The Bendix EverSure Spring Brake provides service braking parking and emergency braking The spring brake can be mounted with the mounting bolts in either a vertical or horizontal plane on standard mounting stud centers Two air hoses are used the service air hose the connector is marked 11 and the parking emergency air hose the connector is marked 12 Controlled air pressure enters the service chamber through the inlet port and acts upon the diaphragm moving the push plate and rod assembly forward When the service chamber is used to actuate cam type brake foundation assemblies the yoke which is welded to or threaded on the push rod is connected to a slack adjuster which in turn is connected to the brake cam shaft This forward motion of the push rod rotates the slack adjuster cam shaft and cam applying the vehicle brakes The greater air pressure admitte
14. e replacement spring brake chamber may need to be clocked rotated to properly position the ports or clamp band hardware To do so follow the clocking procedure Additionally the push rod may need to be cut to the proper length for the application Refer to the Bendix ASA 5 slack adjuster service data sheet SD 05 1269 or the Bendix Versajust slack adjuster service data sheet SD 05 4630 as applicable or see guidelines on proper push rod lengths for use with these slack adjusters A WARNING Do not mechanically release cage the spring if there is any structural damage to the brake Caging the spring in such a chamber may cause serious injury or death Replace the complete spring brake assembly 7 0 1 Ifthe service replacement spring brake chamber is not caged mechanically release cage the replacement spring brake chamber by following the original manufacturer s instructions 7 0 2 Apply 10 psi 1 bar of air pressure to the service port 11 of the spring brake chamber 7 0 3 Since we will be using locking pliers to hold the service push rod in place be sure to protect the threads before clamping down The locking pliers will prevent the push rod from retracting when they are used at the push rod opening of the replacement spring brake chamber 7 0 4 Release the air pressure from the service port 7 0 5 Remove the clamp ring and hardware from the spring brake chamber 7 0 6 Position the adapter base inlet port
15. eplace the complete assembly 11 2 REPLACING THE COMBINATION SPRING BRAKE 11 2 1 Mechanically release cage the old spring brake chamber by following the original manufacturer s instructions or use Section 8 for Bendix brand spring brakes 11 2 2 Drain system pressure and then disconnect the air hoses from the service brake chamber Be sure to mark both hoses to ensure proper re installation 11 2 3 Remove the cotter and yoke pins disconnect the yoke from the slack adjuster remove the mounting nuts washer and lock washers and remove the combination spring brake While removing use care to prevent the combination spring brake from falling 11 2 4 Remove the brake chamber mounting hardware from the mounting studs 11 2 5 Remove the service brake chamber from its mounting bracket 11 3 CLOCKING ROTATING THE REPLACEMENT BRAKE CHAMBER See Section 7 for clocking instructions INSTALLATION 11 3 1 Clean and inspect the mounting bracket Mount the service brake chamber to the mounting bracket 11 3 2 Ifthe service replacement is a type that provides an extra long threaded push rod thread a nut onto the rod past the point that it will need to be cut Taking all necessary safety precautions cut the rod to the required length and remove burrs Remove the nut installed earlier to ensure that the threads are clear 11 3 3 Install the combination spring brake using the furnished hardware Torque the mounting nuts to 133 1
16. he power spring by applying air to the port marked 12 before turning the release bolt nut with a hand wrench or simply by hand 6 0 2 Remove the dust cap from the keyhole in the center of the spring brake chamber See Figure 1 6 0 3 Remove the release tool assembly from the side pocket of the spring brake chamber 6 0 4 Insert the release tool T bolt through the release tool keyhole and into the power spring piston plate 6 0 5 Turn the release tool one quarter turn clockwise SERVICEABLE SECTION PRESSURE PLATE SERVICE RETURN SPRING NUT WASHER CLAMP BAND NON SERVICEABLE PIGGYBACK SECTION RELEASE TOOL DUST CAP SERVICE DIAPHRAGM PARKING EMERGENCY BRAKE FIGURE 4 EXPLODED VIEW SHOWING SERVICEABLE AND NON SERVICEABLE PORTIONS OF THE BRAKE 6 0 6 Pull on the release tool to ensure the T section is properly seated in the power spring piston plate 6 0 7 Assemble the release tool washer and nut onto the release bolt and finger tighten only If caging is being done manually it is recommended that some type of lubrication be applied to the release bolt threads prior to tightening to prevent galling or stripping 6 0 8 To manually cage the spring brake turn the release tool nut clockwise with a hand wrench The maximum releasing torque should not exceed 50 Ib ft 67 8 Nm If the spring has not previously been compressed by the use of air 6 0 1 above verify that the service side push rod is ret
17. ng Brake When either the diaphragm spring or both are replaced they should be replaced in the corresponding chamber on the same axle Use only genuine Bendix brand replacement parts A WARNING A spring brake chamber cannot have the emergency diaphragm replaced Replace the whole spring brake chamber 12 0 1 Protect the service push rod with tape and lock the locking pliers on the push rod close to the non pressure plate This will hold the rod in the applied position 12 0 2 Ensure thatthe spring brake chamber is caged To cage the spring brake chamber perform the steps outlined in either Step 6 0 Mechanical Release Caging of the Bendix EverSure Spring Brake or Step 8 0 Mechanical Release Caging and Removal of the Piggyback Spring Brake Chamber to be Replaced 12 0 3 Mark the service clamp ring and non pressure plate to ensure proper alignment of parts during reassembly 12 0 4 Remove the service clamp ring assembly and the chamber The service clamp ring is closest to the non pressure plate and slack adjuster See provided illustrations if in doubt 12 0 5 12 0 6 Line up the spring brake chamber the service diaphragm and the non pressure housing ensuring that they are centered see Figure 5 Install new diaphragm 12 0 7 Re assemble the service clamp assembly Ensure all parts are seated properly and remain centered 12 0 8 Torque the clamp nuts to 20 30 ft lbs Remove the locking pliers from the
18. racting during the process and that the release bolt is extending from inside the spring brake housing DO NOT USE A HIGH SPEED AND OR POWER DRIVEN IMPACT WRENCH 6 0 9 Rotate the release bolt nut clockwise until an increased resistance is encountered This should indicate that proper caging is complete The release bolt should be extended all the way back as shown in Figure 4 DO NOT OVER TORQUE RELEASE BOLT OVER TORQUING CAN CAUSE SPRING BRAKE DAMAGE 6 0 10 Release the air pressure from the emergency parking port port 12 after caging and prior to any disassembly or removal from the vehicle IMPORTANT To ensure the power spring is fully caged the extended release tool length should be fully backed out as shown in Figure 4 A WARNING Do not use an impact wrench An impact wrench may over torque the release tool and cause damage to the pressure plate 6 1 SPRING BRAKE CHAMBER REMOVAL 6 1 1 With the spring brake chamber caged and all air pressure drained from the air brake system disconnect the air hoses from the spring brake chamber 6 1 2 Remove the cotter pin from the yoke Remove the yoke pin 6 1 3 While supporting the spring brake chamber in position remove and discard brake chamber mounting nuts and washers see Figure 3 Nuts and washers must not be re used Remove the spring brake 7 0 CLOCKING ROTATING THE BENDIX SERVICE REPLACEMENT SPRING BRAKE CHAMBER NOTE For proper installation the servic
19. service push rod 12 0 9 Reconnect the emergency air hose to the emergency port marked 12 and reconnect the service air line to the service port marked 11 12 0 10 Pressurize the service half by putting air into the service port Perform the Leakage Test Section 4 2 12 0 11 Perform the Functional Test and Stroke Section 4 1 12 0 12 Uncage the main spring and return the release tool into the release tool side pocket See Section 10 12 0 13 Replace the dust cap in the keyhole A WARNING Check for proper service and emergency operation after servicing any part of the brake chamber s Check the brake adjustment if the combination spring brake was removed installed Follow the vehicle manufacturer s instructions to adjust the brakes Bendix brand foundation brake products are brought to you by Bendix Spicer Foundation Brake LLC BW7506 2011 Bendix Commercial Vehicle Systems LLC 08 11 All Rights Reserved Printed in the United States
20. terior of nylon A WARNING e Spring brake chambers contain a loaded compression spring Property damage serious injury or death may occur if instructions are not followed completely e When performing any maintenance on the spring brakes make sure to block the wheels to prevent vehicle rollaway e DO NOT SERVICE A SPRING BRAKE CHAMBER IF IT HAS STRUCTURAL DAMAGE OF ANY KIND Replace the complete assembly Dismount a damaged spring brake by first cutting the service push rod with an acetylene torch to relieve any force it might have e Do not strike any part of a spring brake chamber for any reason This may cause structural damage e Be careful not to drop a spring brake chamber at any time If dropped inspect for signs of structural damage Replace complete assembly if damaged e Spring brake chambers cannot have the emergency diaphragm replaced Replace the whole spring brake chamber e Always work from the side of the spring brake chamber Never work from the front or back 3 0 PREVENTIVE MAINTENANCE Important Review the warranty policy before performing any intrusive maintenance procedures An extended warranty may be voided if intrusive maintenance is performed during this period Because no two vehicles operate under identical conditions maintenance intervals will vary Experience is a valuable guide in determining the best maintenance interval for a vehicle 3 1 EVERY 300 OPERATING HOURS 8 000 MILES OR O
21. vice port Do not exceed 120 psig Perform the Leakage Test 4 2 10 0 UN CAGING THE BENDIX EVERSURE SPRING BRAKE CHAMBER APPLY PARK BRAKE 10 1 Verify that the spring brake has been properly installed on the spring brake bracket and properly attached to the slack adjuster 10 2 Apply air pressure 100 120 psi 6 6 8 0 bar to restrain by air force the power spring 10 3 Turn the release bolt nut counter clockwise with a hand wrench DO NOT USE HIGH SPEED OR POWER DRIVEN IMPACT WRENCH 10 4 Connect a regulated air line to the emergency parking brake port marked 12 of the chamber if not connected previously 10 5 Continue to turn the release bolt nut until the caging tool is loose Remove caging bolt nut and washer 10 6 Push the release bolt tool in turn the release bolt a quarter turn counter clockwise and remove it from the pressure plate key hole 10 7 With hands clear of moving parts slowly release the air pressure to the emergency parking brake port 12 Be sure to exercise caution to prevent pinching of fingers 10 8 Place caging bolt in spring brake tool holder with T head down and seated in slot Install washer and nut up on exposed threads this allows the washer to protect the holder cavity and caging bolt from corrosive elements and torque the caging bolt nut to 10 15 Ib ft 14 20 Nm 10 9 Mount the dust plug weather seal in the keyhole located at the rear center of the spring brake ch
Download Pdf Manuals
Related Search