Bell'O PR-25 User's Manual
Contents
1. 8 SCREW two cam lock pins 1 into the tops of the cabinet sides B and C A PLACE two smaller dowels 3 into the tops of the cabinet sides and the tops of the dividers 1 B PLACE two cam locks 2 into the interior of each cabinet side C CAREFULLY ALIGN the cabinet top panel A with the top of the cabinet sides and dividers and SECURE them together by turning the cam locks to tighten DO NOT FORCE the pieces together Alignment may require some slight movement of the parts to get the proper fit Fig 9 9 Working from the rear of the cabinet SCREW two rear panels K1 and K2 to the cabinet using screws 4 NOTE THE REAR PANELS ARE MADE TO BE SNUG DO NOT FORCE OR BEND THE PANELS MORE THAN VERY SLIGHTLY IF NEEDED Fig 10 e S Ensure table is level by adjusting rear legs J This will also aide in leveling the doors 10 SCREW the lower door hinges 12 to the interior of the cabinet using screws 11 A ATTACH the cabinet doors L to the hinges 12 using screws 11 B ATTACH the lower cabinet knobs 13 to the doors using screws 8 Fig 11 Aligning the Doors 11 ALIGN the doors by adjusting the screws on the insides of each hinge 11 using the supplied screwdriver tool as shown Belo simply beautiful Warranty One 1 Year Limited Warranty All Bell O International products2. Bel simply beautiful PR 25 Real Wood Audio Video Cabinet ASSEMBLY INSTRUCTIONS Patent Pending PARTS LIST PART DESCRIPTION QUANTITY A CABINET TOP gt 1PC B LEFT SIDE SUPPORT PANEL 1PC C RIGHT SIDE SUPPORT PANEL 1PC D UPPER INTERIOR SHELF 1PC E MIDDLE INTERIOR SHELF 1PC F BOTTOM SHELF 1PC G TOP DOOR PANEL 1 PC H LOWER SHELF DIVIDER 2PCS I UPPER SHELF DIVIDERS 2PCS J CENTER SUPPORT LEG 1PC PARTS LIST Continued PART DESCRIPTION QUANTITY K1 UPPER BACK PANEL 1PC K2 LOWER BACK PANEL 1PC L LOWER CABINET DOORS 2PCS 1 CAM LOCK PIN 18 PCS 2 CAM LOCK 18 PCS 3 30MM DOWEL 32 PCS 4 03X12MM SCREW gap 33 PCS N 5 50MM DOWEL 4 PCS 6 LEFT DRAWER HINGE 1PC 7 UPPER DOOR KNOB 2PCS PARTS LIST Continued PART DESCRIPTION QUANTITY 8 05 32 x 22MM SCREW 4PCS 9 RIGHT DRAWER HINGE 1PCS 10 HINGE PIN 2PCS 11 3 5 X 15MM SCREW 16 PCS 12 LOWER DOOR HINGE 4PCS 13 LOWER CABINET KNOB o 2PCS j 14 TOP SHELF SUPPORT ROD 1PC FOR YOUR SAFETY PLEASE FOLLOW THESE PRECAUTIONS ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE SHELVES AND DOORS HAVE BEEN INSTALLED AND OR WHEN THERE IS EQUIPMENT LOCATED ON OR IN THE FURNITURE AS THIS MAY CAUSE THE SHELVES AND OTHER ITEMS TO BECOME UNSECURED AND
3. FALL WHEN IN USE THIS FURNITURE MUST BE PLACED ON A FLAT SOLID AND LEVEL SURFACE I DO NOT LEAN ON THE TV WHEN IT IS ON THE TV STAND DO NOT CLIMB OR STEP ON THE STAND DO NOT BANG OR PLACE YOUR OWN WEIGHT ON THE DOORS DO NOT PLACE ITEMS ON THE SHELVES WHICH EXCEED THE MAXIMUM WEIGHT LIMITS OF 200 LBS FOR TOP SHELF EG AND 50 LBS FOR EACH LOWER SHELF P ASSEMBLY INSTRUCTIONS NOTE 2 PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS FURNITURE THIS TABLE IS CONSTRUCTED WITH REAL WOOD VENEER TO AVOID DAMAGE DURING ASSEMBLY IT SHOULD BE ASSEMBLED ON A SOFT SURFACE Fig 1 D 1 PLACE the bottom shelf F on edge PLACE four smaller dowels 3 into the holes in the top side of the bottom shelf as shown in Fig 1 PLACE the edge of one of the dividers H onto the dowels with the FRONT arrow facing the front of the shelf the edge without the cut out slots as shown Fig 2 gt 2 PLACE four larger dowels 5 half way through the lower middle shelf E and PLACE the ends of the dowels into the exposed edge of the divider H as shown in Fig 2 Fig 3 3 PLACE the second divider H over the exposed ends of the dowels 5 on the opposite side of the lower middle shelf E with the FRONT arrow facing the front of the shelf the edge without the cut out slots as shown in Fig 3 Fig 4 7 4 Place four smaller dowels 3 into th
4. are warranted with the exception of glass to the original purchaser at the time of purchase and for a period of one 1 year thereafter Glass is warranted to the original purchaser at the time of purchase and for a period of thirty 30 days thereafter Warranty is only valid in the United States of America In order to provide you with timely assistance please thoroughly inspect your furniture for missing or defective parts immediately after opening the carton To receive replacement or missing part s under this warranty go to our website at www bello com or call our Customer Service Department at 1 888 235 7646 Please have the model number and part number s for reference You will also need your sales receipt or other proof of purchase Replacement part s will be shipped to you at no charge with Bell O International assuming all shipping and handling expense We warrant to you the original purchaser that our furniture and all of its parts and components are free of defects in material or workmanship Defects as used in this warranty is defined as any imperfections that impair the use of the furniture or product Our warranty is expressly limited to the replacement of furniture parts and components For one 1 year after the date of purchase Bell O International will replace any part described on the enclosed furniture parts list that is defective in material or workmanship This warranty applies under conditions of normal use Our fur
5. do not allow limitation on how long an implied warranty can last or the exclusion of limitation of incidental or consequential damages so the above limitation and exclusion may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state BELL O INTERNATIONAL CORPORATION 711 Ginesi Drive Morganville NJ 07751 1235 Phone 732 972 1333 Fax 732 536 6482 Web www bello com E mail sales bello com
6. e holes on the exposed edge of the divider H Place the upper interior shelf D onto the dowels as shown Fig 5 5 PLACE the left cabinet side B on a soft surface with the levelling foot facing the rear as shown A SCREW two cam lock pins 1 into the upper and center cross frame and three cam lock pins 1 into the bottom cross frame INSERT two smaller dowels 3 into each of the cross frames B INSERT two cam locks 2 into the underside of each shelf panel D E and three cam locks into the underside of the bottom shelf panel F as shown C INSERT hinge pin 10 into the cabinet side above the top shelf as shown in Fig 5 D With the arrows on the dividers H facing FORWARD CAREFULLY ALIGN the assembled interior shelves and dividers with cam lock pins and dowels on the cabinet side and SECURE them together by turning the cam locks to tighten DO NOT FORCE the pieces together Alignment may require some slight movement of the parts to get the proper fit E INSERT the top shelf support rod 14 into the predrilled holes in the cabinet side B as shown Fig 6 6 Placement of the right cabinet side C A SCREW two cam lock pins 1 into the upper and center cross frame and three cam lock pins 1 into the bottom cross frame INSERT two smaller dowels 3 into each of the cross frames B INSERT two cam locks 2 into the underside of each shelf pan
7. el D E and three cam locks into the underside of the bottom shelf panel F as shown C CAREFULLY ALIGN and PLACE the top door panel G onto the cabinet side B so that it is resting on the hinge pin 10 INSERT the remaining hinge pin 10 into the exposed end of the top door panel as shown in Fig 6 D With the adjustable foot on the cabinet side panel C facing towards the rear CAREFULLY ALIGN the cabinet side panel with the assembled interior shelves and dividers and SECURE them together by turning the cam locks to tighten DO NOT FORCE the pieces together Alignment may require some slight movement of the parts to get the proper fit E SCREW the adjustable center leg J into the insert located in the bottom of the cabinet Fig 7 7 CAREFULLY TURN the partially assembled cabinet upright A SCREW the LEFT drop down door hinge 6 and RIGHT door hinge 9 into the interior sides of the cabinet using the small Philips head screws 4 NOTE THE DOOR TENSION ON THE HINGES CAN BE ADJUSTED BY TURNING THE KNOB LOCATED ON THE HINGE B INSERT four smaller dowels 3 into the upper interior shelf D ALIGN and PLACE the two upper cabinet dividers I onto the dowels as shown in Fig 7 C ATTACH the two upper door knobs 7 to the drop down door using screws 8 Fig 8 gt
8. niture products are not intended for outdoor use The warranty does not cover 1 defects caused by improper assembly or disassembly 2 defects caused by shipping claims for damage during transit to you should be placed immediately by you to the transportation company 3 defects occurring after purchase due to product modification intentional damage accident misuse abuse negligence or exposure to the elements 4 cosmetic damage and 5 labor or assembly costs There are no warranties express or implied including without limitation merchantability or fitness for particular use except as i contained herein or ii required by applicable law in the state whose law governs which shall be New Jersey absent controlling law imposing the law of another state in lieu thereof as governing law All warranties of whatsoever derivation shall be limited to the term set forth above unless otherwise required by applicable law Manufacturer s employees or representatives ORAL OR OTHER WRITTEN STATEMENTS DO NOT CONSTITUTE WARRANTIES shall not be relied upon by Buyer and are not a part of the contract for sale or this limited warranty Except as provided herein Bell O International shall have no liability or responsibility to the purchaser or any other person or entity with respect to any liability loss or damage caused directly or indirectly by use of the product including but not limited to any incidental or consequential damages Some states
Download Pdf Manuals
Related Search