Belkin OMNIVIEW F1DA104PEA User's Manual
Contents
1. Attach the power supply to the DC power jack labeled DC 12V 1A located on the rear of the PRO2 PS 2 Once the power is connected to a power source the LED for port 01 will begin flashing Sequentially push the direct access port selectors for ports 01 through 08 04 for F1DA104Pea and 16 for F1DA116Pea The corresponding LED should flash as each button is pressed indicating that the port is ready for connecting your servers computer connection 10 Connect the Computer 1 Using an OmniView KVM Cable Belkin part F3X1105b XX plug in the male VGA connector to the VGA port on the computer Connect the other end the female connector of the VGA cable to the back of the PRO2 PS 2 labeled VGA 01 2 Connect the PS 2 keyboard and PS 2 mouse connectors of the cable to the keyboard and mouse ports on the computer Connect the other ends of the cables to the keyboard and mouse ports located directly underneath VGA 01 on the PRO2 PS 2 Belkin part F3X1105b XX 3 Repeat steps 1 and 2 for each additional PS 2 computer you wish to connect 11 Connecting Multiple PRO2 PS 2s Daisy Chaining You can daisy chain up to 16 PRO2 PS 2s together giving a server administrator cont2. OmniView KVM Switches OmniView E Series This series of desktop OmniView KVM Switches allows you to control two or four PS 2 computers from one Console and makes switching between computers more convenient Designed for compatibility with your PS 2 platform it reduces desktop clutter and provides a simple reliable solution at a lower price point The E Series KVM Switch supports high quality resolution of up to 2048x1536 85Hz through a 400MHz bandwidth when used with coaxial VGA cabling This means that Belkin OmniView products offer the highest resolution without compromising the quality of the display Power for the KVM Switch draws off the keyboard so that the Switch requires no additional power supply and fewer cables Standard E Series features include hot key functionality keyboard and PS 2 emulations for error free boot up and a Belkin Two Year Warranty F1DB102P E Series 2 Port KVM Switch PS 2 Only F1DB104P E Series 4 Port KVM Switch PS 2 Only OmniView SOHO Series with Audio This innovative design provides built in cable management and saves space while adding a whole new sculpted look to your desktop The SOHO Series Switches allow you to control two or four PS 2 computers from one Console You ll enjoy the greatest interface flexibility with PS 2 and USB combination Switches They offer you expanded compatibility with either interface or both along with the additional convenience of manual push button port selection on
3. PRO2 PS 2 Switch with On Screen Display Control up to 16 computers from one PS 2 console HI Switch with On Screen Display Control up to 16 computers from one PS 2 console Switch avec affichage l cran Contr lez jusqu 16 ordinateurs partir d une console PS 2 DE Masterswitch mit Bildschirmmen Zur Kontrolle von bis zu 16 Computern mit nur einer PS 2 Konsole Switch met On Screen Display Tot 16 computers beheren met slechts n PS 2 console EJ Conmutador con OSD men s en la pantalla Controla hasta 16 ordenadores desde una sola consola PS 2 Switch con On Screen Display Per gestire fino a 16 computer da una console PS 2 User Manual Manuel de l utilisateur Benutzerhandbuch Handleiding Manual del usuario Manuale utente o F1DA108Pea F1DA116Pea Table of Contents Overview Feature Overview eee 2 Equipment Reguiremernts ue IR x wok Ee x xc xs ow see A A 3 lege te CEET 4 Unit Display DiagramS 2 su mue 62 6 6 2 88 incipere 0 4 ebeGs Seed SG 5 Eet eher Lt Tei CEET 7 Installation Pre Configuration 6 6 eum Pee ems a bom oe e me I c we o we 8 Step by Step Installation Guide 9 single PRO2 PS 2 Installation sau kia Rm 10 Connecting Multiple PRO2 PS 2s Daisy Chaining 12 Powering up the SystemS xus we be ee er re X X Y we yd 16 Using your PRO2 PS 2 Selecting a Computer Using Keyboard Hot Key Commands 17 AutoScan Modea d ace Xo ngon he tw h
4. BANK 01 Connect the other end of the daisy chain cable to the Master Input Slave Output port of the Slave switch that you are adding for example BANK 02 Repeat steps 6 and 7 for additional PRO2 PS 2s you wish to daisy chain together 14 Example of Daisy Chain Configuration Master unit BANK 00 eg o5 mega CP BANK 01 Slave unit BANK 02 Slave unit BANK 03 Connecting the Computers 9 10 TT Connect all computers to the Master and Slave switches Refer to Single PRO2 PS 2 Installation on page 10 for instruction on how to connect the Console and the computers to the PRO2 PS 2 Connect the power supply to the Master switch Power up the Master switch You should see the Master switch light up and display the digits 00 indicating its BANK address Power up the Slave switches sequentially beginning with Bank 01 by connecting each unit s power supply Each switch should display its corresponding BANK address number as it is powered up Note If the PRO2 PS 2s do not enumerate correctly reset the Master switch BANK 00 by simul
5. 7 5 inch 438mm x 89mm x 190mm Weight F1DA104Pea 5 3 Ibs 2414 5 grams F1DA108Pea 9 2 Ibs 4181 5 grams F1DA116Pea 12 Ibs 5472 5 grams Operating Temp 32 to 104 F 0 40 C Storage Temp 4 to 140 F 20 60 C Humidity 0 8096 RH non condensing Warranty 3 years Note Specifications are subject to change without notice Installation Pre Configuration Where to Place the PRO2 PS 2 The enclosure of the PRO2 PS 2 is designed for standalone or rack mount configuration The 8 and 16 port PRO2 PS 2s are natively rack mountable in standard 19 inch server racks Rack mount hardware is included with these switches for a study rack installation An optional rack mount kit F1D005 is available for use with the 4 Port PRO2 PS 2 Consider the following when deciding where to place the PRO2 PS 2 e whether or not you intend to use the direct access port selectors e the lengths of the cables attached to your keyboard monitor and mouse e the location of your CPUs in relation to your console e and the lengths of the cables you use to connect your computers to the PRO2 PS 2 Cable Distance Requirements VGA signals transmit best up to 25 feet Beyond that length the probability of video degradation increases For this reason we recommend that the length of the cables between the PRO2 PS 2 and the connected computers does not exceed 25 feet Note If you need your console to reside further than 25 feet f
6. Identification tag displays on screen after making a port selection You may choose 7 15 30 or 60 seconds For both settings you may use the arrow keys to navigate After you have selected the desired time intervals push Enter key to save the entry Press the ESC key to go back to the original OSD menu screen Press the ESC key again to exit the On Screen Display completely Once you have selected a computer on the menu press Enter to switch to that port Note If there are Slave units connected and the AutoScan time and OSD display time settings are set on the Master unit the settings will also apply to all slave units Updating Firmware To update your firmware download the appropriate firmware file and utility from belkin com The utility automatically guides you through the process of updating the firmware on your PRO2 PS 2 Cautions and Warnings We strongly recommend that you update your firmware only if you are currently experiencing mouse and keyboard problems with your PRO2 PS 2 as reconfiguring software may lead to unexpected operational problems Please contact Belkin Tech Support if you need assistance To update the firmware you will need the following items 1 A separate computer running Windows 95 98 or Me This computer must not be connected to the CPU ports on the PRO2 PS 2 2 An available parallel port on the computer 3 A flash cable that connects between the PRO2 PS 2 and
7. On Screen Display or can independently access the desired port by pushing the direct access port selectors 26 How far can the computer be from the PRO2 PS 2 When using PS 2 connections the PRO2 PS 2 can be up to 25 feet away from your computer If your computer needs to be more than 25 feet 7 5 meters from the PRO2 PS 2 you can use the Belkin CAT5 Extender to extend your PS 2 keyboard PS 2 mouse and monitor up to 300 feet away using a standard CAT5 UTP cable What is the maximum video resolution that the PRO2 PS 2 supports The advanced video circuit in the PRO2 PS 2 supports a maximum resolution of 2048x1536 85Hz What video bandwidth does the PRO2 PS 2 support The PRO2 PS 2 supports 400MHz of video bandwidth Do have to install any software to use the PRO2 PS 2 No the PRO2 PS 2 does not require any drivers or software to be installed in your computers Simply connect all your computers to the PC ports on the PRO2 PS 2 then attach one keyboard monitor and mouse to the Console port and it is ready for use 2f e e Does the PRO2 PS 2 require an AC adapter Yes the PRO2 PS 2 requires a 12 Volt DC 1 Amp power adapter in order to function properly Can use the PRO2 PS 2 to switch video signals only Yes you may use the PRO2 PS 2 to switch between video signals only without having to connect the keyboard and mouse The keyboard and mouse should be connected directly to the computer that th
8. at boot up e Check that the keyboard cable between the PRO2 PS 2 and the computer is completely connected Tighten any loose connections e Try using a different keyboard e Try connecting the computer to a different port e f you are using the keyboard software that was included with your keyboard uninstall it and then reinstall the standard Microsoft keyboard driver Mouse The mouse is lost when switch to a different port e Check that the mouse you are using is connected properly to the Console of the PRO2 PS 2 If you are using a mouse driver that was included with your mouse uninstall it and install the standard Microsoft mouse driver Disconnect and reconnect the mouse cable attached to the channel with which you are experiencing problems to re synchronize the mouse connection Make sure the mouse works when directly plugged into the computer If the computer is coming out of standby mode allow up to one minute to regain mouse function De activate power management schemes on the PC with which you are experiencing problems e Try a different mouse 30 The mouse is not detected at boot up e Check the cables and make sure that they are inserted correctly The computer boots up but the mouse does not work e Make sure the mouse is plugged in properly e Make sure the mouse works when directly plugged into the computer Rebooting may be necessary when trying this e Try a different mouse Whe
9. in some models FLASH DIP switch may be located on the back in some models Front View of the PRO2 PS 2 F1DA108Pea Autoscan button LED for selected 7 segment LED port identification for selected BANK identification S Direct access port selectors Manual BANK scroll buttons Back View of the PRO2 PS 2 F1DA108Pea Console VGA Computer VGA port VGA 07 06 VGAO6 VGA 05 VGA 04 VGA02 0 ees 0960 8 07 iS oe E A 5 ems ou O 02 Console PS 2 mouse keyboard ports Flash Upgrade port Master Input Slave Output Computer PS 2 DC power jack mouse keyboard ports Slave Input Specifications Part No F1DA104Pea F1DA108Pea amp F1DA116Pea Power 12 Volt DC 1 Amp power adapter with center pin positive polarity Daisy Chain Maximum of 16 KVM Switches Computer Connections Supported 4 F1DA104Pea 8 F1DA108Pea 16 F1DA116Pea Keyboard Emulation PS 2 Mouse Emulation PS 2 Monitors Supported VGA SVGA MultiSync and LCD optional adapter may be required Max Resolution 2048x1536 85Hz Bandwidth 400MHz Keyboard Input 6 pin miniDIN PS 2 Mouse Input 6 pin miniDIN PS 2 VGA Port 15 pin HDDB type Port LED Indicators 4 F1DA104Pea 8 F1DA108Pea 16 F1DA116Pea Enclosure Metal enclosure with high impact plastic faceplate Dimensions F1DA104Pea 11 x 1 75 x 6 inch 279mm x 44 5mm x 150mm F1DA108Pea 17 25 x 1 75 x 7 5 inch 488mm x 44 5mm x 190mm F1DA116Pea 17 25 x 3 5 x
10. receive and transmit data through nickel plated connectors The industry standard 14 pin coaxial VGA cabling was designed to support image clarity for high resolution applications The gray jacket bends into even the tightest crawl spaces for an excellent fit The PRO2 PS 2 Series Plus Cable is available in PS 2 and USB style cable kits F3X1105b XX PS 2 available in lengths of 6 10 15 and 25 feet F3X1962 XX USB available in lengths of 6 10 and 15 feet XX denotes length in feet 25 What operating systems does the PRO2 PS 2 support The PRO2 PS 2 will support any operating system that runs ona PS 2 platform What does flash upgradeable mean With flash upgrade capability you can update your PRO2 PS 2 firmware at any time through a simple parallel connection Internet upgrade capability ensures that your PRO2 PS 2 is always the most current version on the market with the latest features and enhancements See the section on firmware updates in this manual page 21 and when to use them Does the PRO2 PS 2 support Microsoft IntelliMouse The PRO2 PS 2 supports mice from Microsoft Logitech Kensington etc and Belkin Please contact Belkin Technical Support for compatibility issues you may experience How does the PRO2 PS 2 allow the user to switch between ports The PRO2 PS 2 supports three methods of port selection The user Can select computers using specially designated keyboard hot keys through
11. the computer 4 Firmware update files available at belkin com 21 Connecting Computers 1 Connect a keyboard monitor and mouse to the computer you prepared for firmware update It must run Windows 95 98 or Me 2 Connect the power adapter to the PRO2 PS 2 Be sure that all connected computers are powered off at this moment 3 Connect the flash cable Setting the PRO2 PS 2 into Flash Mode The PRO2 PS 2 has four Flash DIP switches DIP Switch Firmware 1 2 3 4 ON OFF OFF OFF Main OFF ON OFF OFF OSD ON ON OFF OFF Keyboard 1 OFF OFF ON OFF Mouse 1 ON OFF ON OFF F1DA116Pea Only Keyboard 2 OFF ON ON OFF F1DA116Pea Only Mouse 2 The DIP switch should be set to the specified settings when you are attempting to update a particular firmware For example set DIP switch 1 to ON to flash update the main firmware of the switch Note F1DA116P requires that you flash update two firmwares for the mouse and keyboard separately 1 Once the above steps have been completed run the Flash software executable Make sure that the appropriate Flash DIP switch is set to the on position Only one firmware can be flashed at one time 2 After the Flash update has been completed unplug the power supply from the PRO2 PS 2 3 Set all DIP switches to the Off position 4 You are now ready to use your PRO2 PS 2 or continue flashing a different component if necessary 22 Belkin KVM switches and accessories
12. 4 LVP EN61000 3 2 and EN61000 3 3 ICES This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme t la norme NMB 003 du Canada Belkin Components Limited Three Year Product Warranty Belkin Components warrants this product against defects in materials and workmanship for its warranty period If a defect is discovered Belkin will at its option repair or replace the product at no charge provided it is returned during the warranty period with transportation charges prepaid to the authorized Belkin dealer from whom you purchased the product Proof of purchase may be required This warranty does not apply if the product has been damaged by accident abuse misuse or misapplication if the product has been modified without the written permission of Belkin or if any Belkin serial number has been removed or defaced THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS WHETHER ORAL OR WRITTEN EXPRESSED OR IMPLIED BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE No Belkin dealer agent or employee is authorized to make any modification extension or addition to this warranty 32 BELKIN IS NOT RESPONSIBLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY INCLUDING BU
13. FF BANK 10 SLAVE ON ON OFF OFF ON OFF BANK 11 SLAVE ON ON ON ON OFF OFF BANK 12 SLAVE ON ON OFF ON OFF OFF BANK 13 SLAVE ON ON ON OFF OFF OFF BANK 14 SLAVE ON ON OFF OFF OFF OFF BANK 15 SLAVE Note On is the down position Example Four 8 Port PRO2 PS 2s F1DA108Pea are daisy chained together for controlling up to 32 computers The DIP switch on the Master unit is set to BANK 00 factory default and the Slave units are each set to a unique BANK between 01 and 15 13 Before You Begin la Make sure that all computers are powered off and that each PRO2 PS 2 has been assigned a unique BANK address Place Master and Slave switches in the desired location Make sure all are turned off and unplugged from the power source Connect the Console monitor keyboard and mouse to the Console ports of the Master switch or Bank 00 as described previously in this installation guide Connecting the Master Switch to the First Slave Switch 4 9 Using the daisy chain cable F1D108 CBL connect one end of the cable to the Master Input Slave Output port on the Master switch BANK 00 Connect the other end of the daisy chain cable to the Master Input Slave Output port of the first Slave switch BANK 01 Adding Additional Slave Units 6 Using the daisy chain cable F1D108 CBL connect one end of the cable to the available daisy chain port labeled Slave Input on the Slave switch for example
14. Select connected computers by either the direct access port selectors located on the front panel of the PRO2 PS 2 using the On Screen Display or by using hot key commands through the Console keyboard It takes approximately 1 2 seconds for the video signal to refresh after switching computers He synchronization of the mouse and keyboard signals also occurs This is normal operation and ensures that proper synchronization is established between the Console and the connected computers 16 Selecting a Computer Using Keyboard Hot Key Commands Switch to the next or previous port with simple keyboard key sequences using the Scroll Lock key and either the up or down arrow keys To send commands to the PRO2 PS 2 the Scroll Lock key must be pressed twice within two seconds The PRO2 PS 2 will beep confirming that it is in hot key mode Next press the up or down arrow keys and the PRO2 PS 2 will switch to either the prior port or the next port AAA AAA Switch to next active port Down arrow Switch to next active port Up arrow With a single switch configuration no daisy chained switches you can switch directly to any port by entering the two digit number of the port you wish to access For example if you press Scroll Lock Scroll Lock 02 the PRO2 PS 2 will switch to the computer on port 2 located yt n Switch to BANK 00 Port 2 02 Note You will have approximately five seconds to complete
15. T NOT LIMITED TO LOST PROFITS DOWNTIME GOODWILL DAMAGE TO OR REPROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH BELKIN PRODUCTS Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties so the above limitations of exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state 33 BELKIN www belkin com Belkin Ltd Express Business Park Shipton Way Rushden NN10 6GL United Kingdom 44 0 1933 35 2000 44 0 1933 31 2000 fax Belkin B V Boeing Avenue 333 1119 PH Schiphol Rijk The Netherlands 31 0 20 654 7300 31 0 20 654 7349 fax Belkin Tech Support Europe 00 800 223 55 460 Belkin GmbH Hanebergstrasse 2 80637 Munich Germany 49 0 89 143405 0 49 0 89 143405 100 fax Belkin SAS 130 rue de Silly 92100 Boulogne Billancourt France 33 0 1 34 58 14 00 33 0 1 39 46 62 89 fax 2005 Belkin Corporation All rights reserved All trade names are registered trademarks of respective manufacturers listed Mac OS and Mac are trademarks of Apple Computer Inc registered in the U S and other countries P75033ea
16. VM Switch e Adjustable Rack mount Brackets with Screws e USB Flash Cable e User Manual e Quick Installation Guide e 12 Volt DC 1 Amp Power Supply e Registration Card uoI12es The PRO2 PS 2s allow you to control up to a maximum of 256 PS 2 computers with one keyboard monitor and mouse They support PS 2 input devices keyboard and mouse as well as VGA SVGA XGA and XGA 2 video Feature Overview Hot Keys Hot key functionality allows you to select a desired port using designated key commands By using a simple hot key sequence on your keyboard selecting one computer from as many as 256 computers is instantaneous For a listing of complete hot key instructions and commands see pages 17 19 AutoScan The AutoScan feature allows you to set your PRO2 PS 2 to scan and monitor the activities of all operating computers connected to the switch one by one The time interval allotted for each computer can be defined or adjusted through the On Screen Display OSD menu For complete instructions on AutoScan usage please refer to page 18 Video Resolution Through a 400MHz bandwidth the PRO2 PS 2s support video resolutions of up to 2048x1536 85Hz To preserve signal integrity at these higher resolutions your PRO2 PS 2 requires 75 Ohm coaxial VGA cabling Flash Upgrade Flash upgradeable firmware allows you to install the latest firmware for your PRO2 PS 2 This enables your PRO2 PS 2 to maintain consistent compatibility
17. displays the current selected BANK If you have only one PRO2 PS 2 it will display BANK 00 BELKIN F DA 0 T BELKIN FIBATOBT mS 12 SERVER Winz7eeo SBERVER MAG O68 10 SERVER win NT Linux SEAVER CHANNELS Ser uF AUTO SCAN TIME CHANNELT ee SELECT CHANNELS ENTER SAVE A ESCn MA IN MENU 4 7 SELECT FPGUP DN BANK INS RON AME TAB SETUP ENTERI SAVELESCI TXIT A symbol indicates that the computer is powered If a computer is connected and is powered up but the OSD menu does not display a symbol you will have to reset the PRO2 PS 2 to re detect the powered computer This is done by simultaneously pressing the BANK and BANK buttons on the front panel T SELECT Navigate to different computers in the same BANK PGUP DN BANK Select previous BANK by pressing the Page Up key and next BANK by pressing the Page Down key Insert RENAME Name each computer up to 15 characters ENTER SAVE Save the content input TAB SETUP Open Setup menu ESC EXIT Exit the On Screen Display 20 AutoScan Time Specifies the amount of time the PRO2 PS 2 remains on a port before switching to the next port while in AutoScan mode You may select different time intervals 7 15 30 or 60 seconds Use the OSD to set the AutoScan time interval OSD Display Time Specifies the amount of time the OSD menu is displayed Also specifies the amount of time the Port
18. e video signal is taken from to ensure that your computer functions properly How long is the warranty for the PRO2 PS 2 The PRO2 PS 2 comes with a three year limited warranty 28 Troubleshooting General My computer does not boot when connected to the PRO2 PS 2 but works fine when I connect the keyboard video and mouse directly to the computer e Make sure that the keyboard and mouse cables are connected tightly between the PRO2 PS 2 and the computer e Check that the keyboard and mouse cables are not crossed Video am getting ghosting shadowing or fuzzy images on my monitor e Check that all video cables are inserted properly e Check that the monitor you are using supports the resolution and refresh rate setting on your computer e Check that the graphics card you are using supports the resolution and refresh rate setting on your computer e Connect the monitor directly into the computer you are having trouble with to see if the problem still appears am getting a black screen on my monitor e Check that all video cables are inserted properly e f you are not using a power adapter check that the keyboard cable is connected and inserted properly between the computer and PRO2 PS 2 for the appropriate port e Connect your monitor directly to the computer to verify that your monitor is functioning properly 29 Keyboard The computer does not detect a keyboard and get a keyboard error reported
19. e wIR OE doa a ee 18 Selecting a Computer Using Direct Access Port Selectors 18 Bank Up and Bank Down Scroll Buttons 18 On Screen Display Menu Control 20 Belkin KVM Switches and Accessories OmniView KVM Switches 0000 ee eee eee ee 23 OmniView All In One KVM CGables 0500 eee 25 OmniView Accessories and Adapters 26 PRO2 PS 2Series EA s 0 0 cee eee eee 27 Troubleshooting 30 Information ssh 34 Overview Congratulations on your purchase of this Belkin OmniView PRO2 PS 2 Series KVM Switch the PRO2 PS 2 Our diverse line of KVM solutions exemplifies the Belkin commitment to delivering high quality durable products at a reasonable price Designed to give you control over multiple computers and servers from one console Belkin PRO2 PS 2s come in a variety of capacities suitable for all configurations large or small Offering intuitive port indicators direct access port selectors high video resolution support and flash upgradeable firmware The PRO2 PS 2 also comes with an unparalleled Belkin Three Year Warranty This manual will provide details about your new PRO2 PS 2 from installation and operation to troubleshooting in the unlikely event of a problem For quick and easy installation please refer to the Quick Installation Guide included in your PRO2 PS 2 packaging Package Contents e OmniView PRO2 PS 2 Series K
20. each hot key sequence With daisy chain switch configuration you can switch between BANKs by pressing Scroll Lock Scroll Lock Page Up to switch to the previous BANK Press Scroll Lock Scroll Lock Page Down to switch to the next BANK z OE e Qe Z4 qur Switch to previous BANK Page Up Switch to next BANK Page Down 17 With a daisy chain switch configuration you can switch directly to any port on any BANK by pressing Scroll Lock Scroll Lock BANK address and port number For example if you press Scroll Lock Scroll Lock 03 05 the computer on BANK 03 Port 5 will become active d WI eu AutoScan Mode Pressing the AutoScan button on the PRO2 PS 2 will activate the AutoScan function In AutoScan mode the PRO2 PS 2 remains on one port for a pre set number of seconds before switching to the next computer This time interval can be adjusted via the On Screen Display menu Note There is no mouse or keyboard control in AutoScan mode This is necessary to prevent data and synchronization errors If the user is using the mouse or keyboard when the PRO2 PS 2 is switching between ports data flow may become interrupted and could result in erratic mouse movement and or wrong character input when using the keyboard Press any button on the front panel or any key on the keyboard to disable AutoScan Selecting a Computer Using Direct Access Port Selec
21. h with the ends of the rails or to extend the PRO2 PS 2 past the front of the rails 2 Determine how far you would like the PRO2 PS 2 to protrude from the rack Select a bracket hole scheme 3 Attach the bracket to the side of your PRO2 PS 2 using the Phillips screws provided Refer to diagram above 4 Mount the PRO2 PS 2 to the rack rail assembly Note If this PRO2 PS 2 will be daisy chained to another PRO2 PS 2 set the BANK address prior to installing on a rack Refer to the section in this user manual labeled Connecting Multiple PRO2 PS 2s Daisy Chaining Your PRO2 PS 2 is now mounted securely into the bracket and you are ready to connect cables to the back of the unit Single PRO2 PS 2 Installation This section provides complete instructions for the hardware setup of a single PRO2 PS 2 F1DA104Pea F1DA108Pea and F1DA116Pea PS 2 Installation Keyboard Video and Mouse Connections Connect the Console 1 Connect the monitor to the PRO2 PS 2 Attach your monitor cable to the HDDB15 female port on the back of the PRO2 PS 2 labeled Console VGA 2 Connect the PS 2 keyboard cable to the keyboard port on the back of the PRO2 PS 2 in the Console section 3 Connect the PS 2 mouse cable to the mouse port on the back of the PRO2 PS 2 in the Console section a Ge dum Ce eA 9999 99
22. n I switch from one port to another mouse movement is completely erratic e Make sure you do not have more than one mouse driver installed Make sure that the driver is either for a standard PS 2 mouse or a Microsoft computer compatible PS 2 mouse e Make sure you do not have any mouse drivers loaded in your CONFIG SYS or AUTOEXEC BAT files e Avoid moving the mouse or pressing the mouse button when switching ports on the PRO2 PS 2 e You can reset the mouse and resume proper mouse movement simply by unplugging the mouse from the front of the PRO2 PS 2 for about 2 3 seconds and then plugging it in again 31 Warranty FCC CE ICES Statement FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We Belkin Components of 501 West Walnut Street Compton CA 90220 declare under our sole responsibility that the products F1DA104P F1DA108P F1DA116P to which this declaration relates Comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation CE Declaration of Conformity We Belkin Components declare under our sole responsibility that the F1DA104P F1DA108P and F1DA116P to which this declaration relates are in conformity with Emissions Standard EN55022 and with Immunity Standard EN5502
23. ort of up to 2048x1536 85Hz requires use of a 75 Ohm coaxial VGA cable to preserve signal integrity VGA cables must have HDDB15 female to HDDB15 male connectors Belkin highly recommends that you use OmniView All In One PRO Series Plus Cables These cables offer the highest quality possible to ensure optimal data transmission All In One Cables are molded together for a clean and organized setup are double shielded to reduce EMI RFI interference have strain relief construction for added durability come with a ferrite bead for noise immunity and include PC99 color coded connectors for easy identification and connection The PRO Series Plus Cables include an industry standard 14 pin coaxial VGA cable and nickel plated connectors for high resolution applications The following cables are recommended for your PRO2 PS 2 OmniView All In One PRO Series Plus F3X1105b XX PS 2 Style XX denotes length in feet Operating Systems OmniView PRO2 PS 2 Series KVM Switches are for use on CPUs using Platforms e Windows 95 98 2000 Me NT XP e DOS e Turbolinux and all Linux distributions e Novell NetWare 4 x 5 x Keyboards e Supports 101 102 104 key keyboards Mice e Microsoft system compatible PS 2 mice having 2 3 4 or 5 buttons e Microsoft system compatible PS 2 wireless or optical mice Monitor e VGA e SVGA e MultiSync Side View of the PRO2 PS 2 BANK DIP switch may be located on the back
24. rol over a maximum of 256 computers When daisy chained together each unit is referred to as a BANK and assigned an address The Console keyboard mouse and monitor connects to BANK 00 and is referred to as the Master switch BANKs 01 through 15 are referred to as Slave switches Note A daisy chain cable F1D108 CBL is required to daisy chain each PRO2 PS 2 and is available through your Belkin reseller or online at belkin com All PRO2 PS 2s feature a BANK DIP switch The BANK DIP switch is used for proper identification and use of PRO2 PS 2s in a single unit or daisy chain configuration e For a single unit configuration set the BANK DIP switch on the PRO2 PS 2 to the Master BANK address 00 setting This is the factory default setting e For multi unit configuration the BANK DIP switch on the Master unit must be set to BANK address 00 Slave units must be set to a unique BANK address from 01 through 15 Refer to the chart below for BANK DIP switch settings 12 BANK DIP Switch Configuration Chart DIP SWITCH BANK ADDRESS 1 2 3 4 5 6 ON ON ON ON ON ON BANK 00 MASTER default ON ON OFF ON ON ON BANK 01 SLAVE ON ON ON OFF ON ON BANK 02 SLAVE ON ON OFF OFF ON ON BANK 03 SLAVE ON ON ON ON OFF ON BANK 04 SLAVE ON ON OFF ON OFF ON BANK 05 SLAVE ON ON ON OFF OFF ON BANK 06 SLAVE ON ON OFF OFF OFF ON BANK 07 SLAVE ON ON ON ON ON OFF BANK 08 SLAVE ON ON OFF ON ON OFF BANK 09 SLAVE ON ON ON OFF ON O
25. rom the PRO2 PS 2 we recommend using the Belkin CAT5 Extender F1D084vea2 with a standard CAT5 UPT cable By using this device you may increase the distance between your PRO2 PS 2 and your keyboard mouse and monitor by as much as 300 feet without risking signal degradation Cautions and Warnings Avoid placing cables near fluorescent lights air conditioning equipment or machines that create electrical noise e g vacuum cleaners Step by Step Installation Guide Cautions and Warnings Before attempting to connect anything to the PRO2 PS 2 or your computer s please ensure that everything is powered off Plugging and unplugging cables while computer s are powered on may cause irreversible damage to the computer s and or the PRO2 PS 2 s Belkin Components is not responsible for damage caused in this way Installing the PRO2 PS 2 into a Server Rack Bracket Installation F1DA108Pea and F1DA116Pea only Eight or 16 Port PRO2 PS 2s include adjustable mounting brackets ideal for installation in 19 inch racks The mounting brackets feature three adjustment positions to allow the faceplate of the PRO2 PS 2 to mount flush to your rack mounted servers or to the rack Please follow these simple steps to achieve the desired adjustment The 4 Port PRO2 PS 2 requires an optional mounting kit F1D005 1 Remove the adjustable brackets from the box The adjustable brackets allow you to set the PRO2 PS 2 s face flus
26. s many as 256 CPUs through dedicated daisy chain ports Video resolutions of up to 1600x1200 65Hz are supported through a 400MHz bandwidth On Screen Display allows you to name and select attached servers using an on screen interface Switch between ports by using hot key commands or direct access port selectors The Omniview PRO2 PS 2 Series KVM Switches use standard cables for easy installation include a 12 Volt DC 1 Amp power supply and are backed by a Belkin Five Year Warranty F1DA104T PRO2 PS 2 Series 4 Port KVM Switch PS 2 amp USB F1DA108T PRO2 PS 2 Series 8 Port KVM Switch PS 2 amp USB F1DA116T PRO2 PS 2 Series 16 Port KVM Switch PS 2 amp USB 24 OmniView All In One KVM Cables OmniView All In One KVM Cables provide you with the quality connections necessary to set up your KVM solution Each kit provides the proper cables and connectors to complete the installation of a Belkin OmniView KVM Switch OmniView All In One KVM Cables feature sturdy construction with strain relief construction and PVC overmolding to prevent data loss Use of 20 gauge wire delivers the high performance cable that users have come to identify with the Belkin name A ferrite bead reduces electromagnetic and radio frequency interference EMI RFI PC99 color coded connectors and modified thumbscrews have been added for easier installation PRO Series Plus The PRO Series Plus Cables are high performance cables built to exacting standards They
27. taneously pressing the BANK and BANK buttons You can also reset the Master switch to detect newly added Slave switches If the switches still do not enumerate correctly check that all switches have the correct BANK address assigned to them and that all daisy chain cables are connected properly 12 Verify that the Master unit has detected all Slave switches by scrolling through the BANKS using the BANK up and BANK down buttons If all Slave switches are detected properly the LED display on the Master switch will register and display the attached Slave switch s BANK address 15 uo1 9aS Using your PRO2 PS 2 Powering up the Systems Once all cables have been connected power up the computers that are attached to the PRO2 PS 2 All computers can be powered on simultaneously The PRO2 PS 2 emulates both a mouse and keyboard on each port and allows your computer to boot normally The computer connected to port 1 will be displayed on the monitor Check to see that the keyboard monitor and mouse are working normally Proceed to do this with all occupied ports to verify that all computers are connected and responding correctly If you encounter an error check your cable connections for that computer and reboot If the problem persists please refer to the Troubleshooting section in this manual Using Your PRO2 PS 2 Now that you have connected your Console and computers to your PRO2 PS 2 it is ready for use
28. the face of the device Switch between speakers and microphones without having to unplug and re plug them when switching computers The flash feature allows users to download firmware updates and ensure compatibility with the latest computers and devices The enclosure design builds in cable management and the Switches are self powered so they require no external power supply and work with fewer cables High quality resolution of up to 2048x1536 85Hz is supported through a 400MHz bandwidth by the OmniView SOHO Series with Audio KVM Switch when used with coaxial VGA cabling offering the highest resolution without compromising the quality of the display Other standard features found on this unit include hot key functionality keyboard and PS 2 emulations for error free boot up and a Belkin Three Year Warranty 23 F1DS104P SOHO Series 4 Port KVM Switch with Audio PS 2 Only F1DS102T SOHO Series 2 Port KVM Switch with Audio PS 2 amp USB F1DS104T SOHO Series 4 Port KVM Switch with Audio PS 2 amp USB OmniView PRO2 PS 2 Series The OmniView PRO2 PS 2 Series KVM Switches deliver reliability performance and centralized control necessary for today s enterprise environment This series of KVM Switches enables you to control multiple platform servers from a single Console Available in the desktop style 4 port and the 19 inch rack mountable 8 and 16 port models the OmniView PRO2 PS 2 Series KVM Switch expands easily for full control of a
29. tors You can directly select which computer you wish to control by pressing the direct access port selector next to the corresponding port The LED will illuminate to indicate the port is currently selected If you are installing multiple PRO2 PS 2s that are daisy chained use the BANK scroll keys located on the front panel of the Master switch to access other computers that are connected to the Slave switches BANK Up and BANK Down Scroll Buttons Pressing the BANK and BANK scroll buttons on the Master switch will allow you to switch between the daisy chained PRO2 PS 2s Pressing both buttons simultaneously will reset the PRO2 PS 2 The BANK button will take you to the next BANK For example when you are at the Master switch BANK 00 and want to check computers on BANK 02 pressing the BANK button will take you to BANK 02 As a default thefirst active computer will be displayed on the Console monitor Use the direct access port selectors to go to the desired computer on BANK 02 18 The BANK button will take you to the previous BANK For example when you are at BANK 02 and want to check computers in BANK 01 Pressing the BANK button will take you to BANK 01 As default the first active computer will be displayed on the Console monitor Use the direct access port selectors to go to the desired computer on BANK 01 Keyboard Hot Key Commands Conveniently command the PRO2 PS 2 to switch ports through simple ke
30. with the latest devices and computers Firmware upgrades are free for the life of your PRO2 PS 2 Refer to the enclosed flash upgrade instruction document or visit us at belkin com for complete upgrade information and support On Screen Display OSD The OSD feature simplifies server management by allowing you to assign individual names to each connected server throughout the system It provides a visual means of switching between computers and setting the time interval for the AutoScan function Front Panel Push Button Direct access port selectors located conveniently on the front panel of the PRO2 PS 2 allow for simple manual port selection Each button controls a port LED Display An LED display on the face of the PRO2 PS 2 serves as a status monitor An LED next to each direct access port selector illuminates to indicate that the console currently controls the corresponding computer As a port selector is pushed the LED next to it will light up A flashing port LED indicates that there is no computer connected to that port Seven Segment LED Display When daisy chaining multiple PRO2 PS 2s together the seven segment LED display serves as a quick indicator of the selected BANK Equipment Requirements Cables To connect to the PRO2 PS 2 each PS 2 computer requires one VGA cable one PS 2 keyboard cable and one PS 2 mouse cable Keyboard and mouse cables must have PS 2 male to PS 2 male connectors Video resolution supp
31. yboard key sequences To send commands to the PRO2 PS 2 the Scroll Lock key must be pressed twice within two seconds You will hear a beep for confirmation Below is a complete list of hot key commands Note you will have approximately five seconds to complete each hot key sequence SL SL Up Arrow Switch to PREVIOUS ACTIVE port SL SL Down Arrow Switch to NEXT ACTIVE port SL SL Page Up Switch to PREVIOUS BANK By default selects first active port on the BANK SL SL Page Down Switch to NEXT BANK By default selects first active port on the BANK SL SL Y Directly switches to PORT Y on BANK 00 Single Switch Configuration Y 01 to 16 SL SL X Y Directly switches to PORT Y on BANK X Daisy Chain Configuration X200 to 15 Yz01 to 04 for F1DA104T X200 to 15 Yz01 to 08 for F1DA108T X200 to 15 Yz01 to 16 for F1DA116T SL SL Delete Reset On Screen Display menu SL SL S Disable sound in AutoScan mode SL SL Space Bar Activate On Screen Display SL SL A Enable AutoScan mode Refer to AutoScan button 19 UOIJIOS Using your PRO2 PS 2 On Screen Display Menu Control To access the On Screen Display OSD menu press Scroll Lock Scroll Lock and the space bar Immediately the OSD overlay screen will appear The superimposed menu screen is generated by the PRO2 PS 2 and does not affect your computers or software function in any way The main OSD menu is shown below It
Download Pdf Manuals
Related Search