Behringer V-TONEGM110 User's Manual
Contents
1. EURORACK UB2222FX PRO Fig 3 1 Standard set up for recording with the V TONE GM110 To use your V TONE GM110 for rehearsals in the studio or on stage please wire up the unit as shown in fig 2 1 Of course you can also use a wah wah or other pedal effect instead of the external 19 effects unit Connecting the headphones will mute the built in speaker If you wish to use a guitar tuner please connect it to the FX SEND of your V TONE GM110 If there is no further effects device connected you can leave the FX RETURN as it is When using an external effects device the tuner should be placed before the effects device to prevent the tuner from receiving any effects signal 4 AUDIO CONNECTIONS The BEHRINGER V TONE GM110 is fitted with audio inputs and outputs in the form of 1 4 mono jacks The exceptions to this are the headphones output and the D I OUT gt Please ensure that only qualified personnel install and operate the device gt Please make sure that all units have a proper ground connection For your own safety never remove or disable the ground conductor of the unit or of the AC power cable Instead you can eliminate hum problems caused by grounding e g when connected to a mixing console by pressing the GND switch Groundlift2. IS09000 CERTIFIED MANAGEMENT SYSTEM CAUTION REPLACE WITH SAME FUSE TYPE AND RATING ATTENTION UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE ET CALIBRE NE PAS OUVRIR CAUTION to REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER 230 V 50 60 Hz 70 W SERVICING TO QUALIFIED PERSONNEL FUSE T 1 0 A H 250 V CAUTION FIRE OR ELECTRIC SHOCK DO NOT EXPOSE x THIS EQUIPMENT TO RAIN OR MOISTURE SERIAL NUMBER DATE CODE ON T0 REDUCE THE RISK OF SEND RETURN ho h a OUTPUT GND LIFT Fig 2 2 Rear panel connectors FUSEHOLDER VOLTAGE SELECTION Before you connect the device to the network please make sure that your local voltage matches the voltage indicated on the unit Blown fuses may only be replaced by fuses of the same type and rating Some models allow for inserting the fuse holder in two different positions in order to switch over from 230 V to 120 V operation and vice versa Please note that for 120 V operation outside Europe you need to use a fuse of a higher rating The network connection is made via a STANDARD IEC INLET SOCKET Use the enclosed power cord to connect the unit to the mains SERIAL NUMBER Please take the time to fill out the warranty card within 14 days of purchasing the device otherwise you will lose your extended warranty Or simply register online at www behringer com You can use the SPEAKER socket to connect
3. 16 Unbalanced 1 4 TS connector sleeve tip strain relief clamp ground shield signal sleeve tip Fig 4 1 1 4 TS connector input FX send FX return speaker 1 4 TRS headphones connector sleeve tip strain relief clamp ground shield left signal sleeve ring ring right signal tip Aj 4 2 Wiring of a stereo headphones plug 4 AUDIO CONNECTIONS V TONE GM110 Balanced XLR connectors input output 1 ground shield 2 hot ve 3 cold ve For unbalanced use pin 1 and pin 3 have to be bridged Fig 4 3 XLR connectors D I Out 4 1 Loudspeaker connection The GM110 features a loudspeaker connection mono jack socket that allows you to hook up a supplementary speaker Optimum adaptation of the amp to the loudspeaker is ensured with an 4 Q loudspeaker With too high an impedance load the maximum power output will drop in proportion to the resistance connected gt Do not use an instrument cable to connect an external loudspeaker rather use a special loudspeaker cable This will prevent any unnecessary losses of sound and output 5 SPECIFICATIONS AUDIO INPUTS Guitar input Connector 1 4 mono jack socket Type RF filtered input Input impedance approx 1 MQ unbalanced FX return Connector 1 4 mono jack socket Input impedance approx 1 MQ unbalanced AUDIO OUTPUTS FX send Connector 1 4 mono jack socket Type Low impedance line level output Output impedance approx
4. User s Manual I onl O Z TT Version 1 2 July 2004 o Qm Qm BEHRINGER www behringer com JUST LISTEN V TONE V TONE GM110 IMPORTANT SAFETY PRECAUTIONS CAUTION WARNING A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR A To reduce the risk of electric shock do not remove the top cover or the rear section No user serviceable parts inside refer servicing to qualified personnel To reduce the risk of fire or electric shock do not expose this appliance to rain and moisture The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus This symbol wherever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This symbol wherever it appears alerts you to important operating and maintenance instructions in the accompanying literature Please read the manual DETAILED SAFETY INSTRUCTIONS 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as
5. will then issue a return authorization number 2 Subsequently the product must be returned in its original shipping carton together with the return authorization number to the address indicated by BEHRINGER 3 Shipments without freight prepaid will not be accepted 4WARRANTY REGULATIONS 1 Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced 2 If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship The warranty does not cover any such modification adaptation irrespective of whether it was carried out properly or not Under the terms of this warranty BEHRINGER shall not be held responsible for any cost resulting from such a modification adaptation V TONE GM110 3 Free inspections and maintenance repair work are expressly excluded from this warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons tubes guitar string
6. 100 Q unbalanced D I Out Connector XLR Type Balanced low impedance line level output Output impedance approx 100 Q Max output level 22 dBu LOUDSPEAKER OUPUT Connector 1 4 mono jack socket Load impedance nom 4Q SYSTEM SPECIFICATIONS Power amp output 30 Watts RMS into 4 Q LOUDSPEAKER Type 10 Vintage loudspeaker model JENSEN JCH10 35 or BUGERA loudspeaker Impedance 4Q Power handling 35 Watts JENSEN 60 Watts BUGERA POWER SUPPLY Mains voltage USA Canada 120 V 60 Hz Europe U K Australia 230 V 50 Hz Japan 100 V 50 60 Hz General export model 120 230 V 50 60 Hz Power consumption 70 W maximum Fuse 100 120 V T 2A H 250V 200 240 V T 1A H 250V Mains connection Standard IEC receptacle DIMENSIONS WEIGHT Dimensions H x W x D approx 15 381 mm x 14 2 369 mm x 9 242 mm Weight approx 12 5 kg BEHRINGER is constantly striving to maintain the highest quality standards Modifications may be made to existing products without prior notice Specifications and appearance may differ from those listed or illustrated 8 5 SPECIFICATIONS 6 WARRANTY 1 WARRANTY CARD ONLINE REGISTRATION To be protected by the extended warranty the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH in accordance with the conditions stipulated in 3 Failure to return the card in due time date as per postmark will void
7. any extended warranty claims Based on the conditions herein the buyer may also choose to use the online registration option via the Internet www behringer com or www behringer de 2 WARRANTY 1 BEHRINGER BEHRINGER Spezielle Studiotechnik GmbH including all BEHRINGER subsidiaries listed on the enclosed page except BEHRINGER Japan warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one 1 year from the Original date of purchase in accordance with the warranty regulations described below If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under 4 BEHRINGER shall at its discretion either replace or repair the product using suitable new or reconditioned parts In the case that other parts are used which constitute an improvement BEHRINGER may at its discretion charge the customer for the additional cost of these parts 2 If the warranty claim proves to be justified the product will be returned to the user freight prepaid 3 Warranty claims other than those indicated above are expressly excluded 3 RETURN AUTHORIZATION NUMBER 1 To obtain warranty service the buyer or his authorized dealer must call BEHRINGER see enclosed list during normal business hours BEFORE returning the product All inquiries must be accompanied by a description of the problem BEHRINGER
8. pedal or to connect an external power amplifier should you require a greater output The internal signal path will not be interrupted The frequency corrected signal at the FX SEND socket is affected by all GM110 controls The output of the looped in effects device is connected to the FX RETURN socket When you connect a cable to this socket you interrupt the internal signal path Please note that when using the serial effects path the effects device will control the level of wet affected signal to dry direct signal 2 CONTROL ELEMENTS V TONE GM110 3 WIRING TIPS 3 1 Standard set up consisting of guitar external effects device and simultaneous recording V TONE GM110 control panel 9 O a amp V TONE GM110 rear panel HPS3000 optional FX VIRTUALIZER PRO DSP2024P DAT recorder fete ie 10 ie l e ie le TE ng i Hii Be ceecee te i In eg p Ka i Ee IEE p QE iel e r 8 iH flied E Aii ece Cele cee tell bese a 8 i G ae pe 4 B Like Bec celecee Pipe a os a Bec Celecee ieoa GE E ES Bec ececeelel iper g 4 Helo Ceecee fe lic tiga pies a p RO j UDUS ESAL J x i Hec eeleeece a EEG ples E g p go EF G io UE ae Wi ec ececee moolt He c ececee el EE Qa fies 4 og p n bh Eec ceecee Bie a of b Eec celecee g ibr 4 i b Return MG Bid Mt ol 77 GEETHA EI God E pugem U ES TF aS SL
9. this will enable you to give free rein to your creativity without being hampered by budget constraints We are often asked how we manage to produce such high quality devices at such unbelievably low prices The answer is quite simple it s you our customers Many satisfied customers mean large sales volumes enabling us to get better purchasing terms for components etc Isn t it only fair to pass this benefit on to you Because we know that your success is our success too would like to thank all of you who have made the V TONE Series possible You have all made your own personal contributions from the developers to the many other employees at this company and to you the BEHRINGER user My friends it s been worth the effort Thank you very much Uli Behringer 1 INTRODUCTION Thank you for purchasing the V TONE GM110 The GM110 is a modern Guitar Workstation that sets new standards in practice amp engineering When developing the GM110 our primary objective was to reproduce the authentic sound of analog guitar amplifiers and at the same time provide you with a tool for straightforward recording The concept of intuitive operation remained a central consideration Many people contributed to this intense development project studio musicians collectors of vintage guitar amps music and guitar lovers alike We even invited guitar amp tuning experts to help us develop an amplifier that unites the very best of both world
10. an additional loudspeaker to your V TONE GM110 The external loudspeaker should have an impedance of 4 Ohms When using this socket the internal loudspeaker is muted For additional information on connecting an external loudspeaker refer to chapter 4 1 The 6 3 mm PHONES jack allows you to monitor the GM110 s audio signal with a pair of commercially available headphones As soon as this socket is used the loudspeaker will be muted Since speakers can have quite an impact on the sound of a guitar amp both the headphones and D I OUT signals are frequency corrected with speaker correction Without this frequency correction extreme treble frequencies would deteriorate the sound Low impedance headphones may begin to produce distortion at certain volume levels In such cases please reduce the volume by turning back the MASTER control At the D I OUT output balanced XLR socket you can tap the audio signal of the V TONE GM110 in order for example to feed it into a mixing console and record it This audio signal is frequency corrected Speaker Simulation The level of the D I OUT max 22 dBu is designed to provide simple connection to mixers or other audio devices With the GND LIFT switch you can unplug the electrical bonding of the D I OUT if ground loop or humming problems occur FX SEND is the output socket for the serial effects path of the GM110 You can use this to loop in the external effects e g a wah wah
11. aying 4 1 INTRODUCTION gt The following user s manual will familiarize you with the control elements of your new V TONE and let you learn all of its functions After reading this manual store it somewhere where you can easily find in the future should you need to look up some information 1 3 Before you get started 1 3 1 Shipment The V TONE was carefully packed at the assembly plant to assure secure transport Should the condition of the cardboard box suggest that your V TONE may have been damaged in transport please inspect the unit immediately and look for physical indications of damage gt Damaged equipment should NEVER be sent directly to us Please inform the dealer from whom you acquired it immediately as well as the transportation company from which you took delivery Otherwise all claims for replacement repair may be rendered invalid 1 3 2 Initial operation Please make sure that your V TONE is provided with sufficient ventilation and never place it on other amplifiers or in the vicinity of a heater to avoid the risk of overheating gt Before plugging your V TONE into a power socket please make sure you have selected the correct voltage V TONE GM110 The fuse mount near the power cord connector has three triangular markings Two of these triangles are facing opposite one another Your V TONE is set up for the voltage indicated near these markings and can be altered by turning the fuse mount
12. by 180 degrees ATTENTION This does not apply to export models built for 120 V for example gt If you use your V TONE unit with a different voltage you must change the fuses accordingly The correct value of the fuses needed can be found in the chapter SPECIFICATIONS gt Faulty fuses must be replaced with fuses of appropriate rating without exception The correct value of the fuses needed can be found in the chapter SPECIFICATIONS Power is delivered via the cable that was delivered with the V TONE All mandatory safety precautions have been adhered to gt Please make sure that all your equipment is grounded at all times For your own protection you should never tamper with the grounding of the cable or the unit itself The unit shall always be connected to a mains socket outlet with a protective earthing connection You can eliminate humming problems caused by grounding at the D I OUT by pressing the GND switch Groundlift 16 1 3 3 Warranty Please send the completely filled out warranty card within 14 days of purchase to us as warranty claims may otherwise be rendered invalid The serial number of your V TONE is located on the rear Alternatively you may register online at www behringer com 2 CONTROL ELEMENTS 2 1 Front panel ANALOG MODELING AMPLIFIER ores at amp 6 m am m m m ew e amp INPUT DRIVE oy AMP MODE SPEAKER LOW Te a we we we oe oe om oe om
13. ealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH BEHRINGER is a registered trademark ALL RIGHTS RESERVED 2004 BEHRINGER Spezielle Studiotechnik GmbH BEHRINGER Spezielle Studiotechnik GmbH Hanns Martin Schleyer Str 36 38 47877 Willich Munchheide II Germany Tel 49 2154 9206 0 Fax 49 2154 9206 4903 6 WARRANTY 9
14. gs CLEAN HI GAIN and HOT to achieve the basic sound selected with the AMP switch The SPEAKER switch provides you with simulations of two classic guitar loudspeakers 4x12 loudspeakers in a closed back enclosure U K and 2x12 loudspeakers open back U S In addition we have also installed a further frequency response correction FLAT that is specially adapted to the GM110 enclosure Le The LOW control in the EQ section enables you to boost or cut the bass frequencies With the MID control you can boost cut the midrange frequencies The HIGH control governs the upper frequency range 2 CONTROL ELEMENTS 5 V TONE GM110 9 With the WASTER control you determine the overall and headphone volume of your V TONE GM110 It should be set fully to the left when you operate the POWER switch or disconnect the instrument cable from the guitar or amp Use the POWER switch to put the GM110 into operation The POWER switch should always be in the Off position when you are about to connect your unit to the mains Attention The POWER switch does not fully disconnect the unit from the mains Unplug the power cord completely when the unit is not used for prolonged periods of time 2 2 Rear panel Co C gt c gt C gt C gt C gt C gt C gt Co Co ft it i BEHRINGER V TONE MODEL GM110 CONCEIVED AND DESIGNED BY BEHRINGER GERMANY BEH INGER ASSEMBLED IN CHINA UNDER BEHRINGER
15. hat the V TONE will hold its own even under the most demanding stage conditions The housing is made of high grade environment friendly MDF wood consisting of multiply impregnated layers 1 2 DYNAMIZER technology and analog modeling When an electric instrument is amplified that s where you either make it or break it Unlike the signals that have been mixed and mastered the signals of electric instruments have extremely high signal peaks placing the dynamic range of the amp s circuitry under immense strain How your amp reacts to these signal peaks is one of its most defining characteristics That s why we ve equipped all V TONE Series amps with our unique DYNAMIZER preamplifier circuitry It guarantees a lively sound with a lot of punch even when the amp is pushed to its limits Combine that with our V TONE analog modeling and not only do you have amazingly authentic tube sounds at your fingertips you also get the dynamic performance typical of the respective amp type Crystal clear guitar tones come through with transparency warmth and the compression typical of tube amps Even as distortion increases the sound remains lively and full of power without losing any of its assertiveness All along you have full control over the volume Plainly talking you can take the same sound you are used to at your practice room and replicate it in your bedroom at much more reasonable volume levels or you can even record yourself while pl
16. m of BEHRINGER users and thank you very much for expressing your confi dence in us by pur chasing the BEHRINGER V TONE Writing this foreword for you gives me great pleasure because it represents the cul mination of many months of hard work delivered by our engineering team to achieve a very ambitious goal to de velop an outstanding guitar amp that is at the forefront of what is technically possible and that can be used in many different applications Our guitar amps offer you strong performance their sound is amazingly clear and they are easy to use both as direct recording amps as well as stage amps The task of designing our new V TONEs certainly meant a great deal of responsibility which we assumed by focusing on you the discerning user and musician Meeting your expectations also meant a lot of work and night shifts But it was fun too Developing a product usually brings a lot of people together and what a great feeling it is when all who participated in such a project can be proud of what they ve achieved It is our philosophy to share our enjoyment with you because you are the most important member of the BEHRINGER team With your highly competent suggestions for new products you ve made a significant contribution to shaping our company and making it successful In return we guarantee you uncompromising quality as well as excellent technical and audio properties at an extremely reasonable price All of
17. om oe om om om om om om om om om om om om om om om om om om om om om oe ee amp ji T 6 6 6 e oo g AS UP GP SS 9L 9L 9L 9L 9L MID HIGH MASTER ewe we we we we we we we we we we we we we we we we we we we we we we we we we we we we we ao a we ee O Fig 2 1 Front panel control elements INPUT is the GM110 s 1 4 jack input for your guitar Use a commercial 1 4 jack mono cable not from a DIY shop but from a specialist music dealer The DRIVE control determines the amplification in the input section It allows you to finely tune the GM110 preset to the output level of your guitar pick up depending on selected amp mode and speaker combination in order to achieve the desired degree of distortion SP Use the DRIVE control to set the desired sound and use the MASTER control to set the desired volume The AMP switch enables you to emulate the basic sounds from three guitar amp designs these are based on classic amp models and will be familiar to you from numerous recordings The TWEED setting delivers transparent sounds clear as a bell with dynamic bass response The BRITISH setting has an aggression that comes straight from the heart and is powerful with an unmistakable ability to make itself heard Fuller and more balanced and yet subtly differentiated the CALIF ORNIAN setting is particularly suitable for singing lead sounds With the MODE switch you choose between one of three possible gain settin
18. onnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions unless you are qualified to do so V TONE GM110 V TONE True Analog Modeling 3O Watt Guitar Amp with Speaker Simulations and Direct Out A Powerful 30 Watt guitar amplifier equipped with an original JENSEN BUGERA 10 guitar speaker A Authentic V TONE Analog Modeling for 3 classic guitar amps 3 speaker simulation models plus 3 gain modes providing you with 27 modeled sounds A Patented DYNAMIZER circuitry captures every nuance of your playing and lends tube like compression to your tone A Balanced direct out with XLR connector and ground lift delivers full preamplified sound including all amp speaker gain mode drive EQ and level settings for direct recording or connection of an external power amp cabinet combination A FX loop for external effects devices rack effects stomp boxes wah wah pedals etc A Extensive master section with dedicated 3 band EQ and master level control A Wide range drive control for super fat sounds with any pickups A Headphone output with speaker simulation lets you practice anywhere and at any time A Additional 4 Ohm speaker out with automatic internal speaker mute A Rugged construction for years of trouble free use A Conceived and designed by BEHRINGER Germany German Patent No 100 15 833 V TONE GM110 FOREWORD Dear Customer welcome to the tea
19. radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over LAL 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 CAUTION These service instructions are for use by qualified service pers
20. rson retail dealer etc shall be entitled to give any warranty promise on behalf of BEHRINGER 6 CLAIM FOR DAMAGES Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim consequential damages In no event shall the liability of BEHRINGER exceed the invoiced value of the product 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1 This warranty does not exclude or limit the buyer s statutory rights provided by national law in particular any such rights against the seller that arise from a legally effective purchase contract 2 The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law Customers in the European Union please contact BEHRINGER Germany Support for further details Technical specifications and appearance subject to change without notice The information contained herein is correct at the time of printing JENSEN and its respective logo are registered trademarks of its respective owner Their use neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the trademark owners with BEHRINGER BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colours and specification may vary slightly from product Products are sold through our authorised dealers only Distributors and d
21. s The demands placed on a guitar amp are nowadays very broad A guitarist should offer a wide array of sounds but at the same time be able to quickly adapt to specific requirements of various applications be it home recording studio live perfor mances etc That s why it is very important to us to be able to offer you a maximal sound diversity as well as diverse connection possibilities with our V TONE Fret not you will quickly master the V TONE and will be able to quickly learn how to use all of its capabilities easily and intuitively With its up to date circuitry the V TONE features the functionality and dependability of a truly modern guitar amp Yet it is user friendly and problem free as if it were a classic tube combo We highly recommend taking your time to truly learn all of the V TONE s functions so you can reach its maximum potential 1 1 The design concept The philosophy behind BEHRINGER products guarantees a no compromise circuit design and employs the best choice of components The operational amplifiers employed by BEHRINGER and used in the V TONE GM110 are exceptional they boast extreme linearity and very low distortion characteristics To complement this the choice of components includes low tolerance resistors and capacitors high quality potentiometers and switches and several other carefully selected elements The robust housing of your V TONE with its oversize power supply gives you the peace of mind t
22. s illuminants and similar parts 4 Damages defects caused by the following conditions are not covered by this warranty A improper handling neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals A connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used A damages defects caused by force majeure or any other condition that is beyond the control of BEHRINGER 5 Any repair or opening of the unit carried out by unauthorized personnel user included will void the warranty 6 If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty the inspection costs are payable by the customer 7 Products which do not meet the terms of this warranty will be repaired exclusively at the buyer s expense BEHRINGER will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification BEHRINGER will return the unit C O D with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent in a written repair order 5 WARRANTY TRANSFERABILITY This warranty is extended exclusively to the original buyer customer of retail dealer and is not transferable to anyone who may subsequently purchase this product No other pe
Download Pdf Manuals
Related Search