Barco PDS-902 User's Manual
Contents
1. Chapter 4 Save Config Select and Adjust Input Select an input and perform the necessary image adjustments Chapter 4 Input Menu Save Input Configuration After completing all adjustments for an input save the input configuration Chapter 4 Save Config Repeat for Each Input Repeat steps 10 and 11 for each input that you have connected to the PDS Adjust System Parameters Adjust parameters such as transition time display brightness user prefs Chapter 4 User Preference Menu System Menu Save System Configuration After completing all system adjustments save the system configuration Chapter 4 Save System State Enable Remote Control Optional Connect Ethernet or Serial communications and issue desired commands Appendix B Remote Control Ready to Roll With all output input and system configurations saved press the desired input button and press TAKE P N 26 1204004 00 Rev 01 Barco Inc BARCO nEn PDS Series ee See Fax Technical Support 1 866 374 7878 Quick Start Guide Website BE Visibly yours Analog Inputs DVI I Inputs HD SD SDI Input Program Outputs Preview Outputs Communications Connect to analog sources such Connect to DVI or analog sources Connect to 3G HD SD 1 x DVI 1 x Analog provided Connect to DVI or Ethernet and Serial connectors are provided as PCs VIRs and camera2. ing TAKE Program black transition Use the Setup Menu and pending sources flip flop Quick Setup and Operations The following list summarizes PDS setup and operations For error free installation always refer to the listed section in the User s Guide Connect Power Ensure that power is properly connected to the PDS Chapter 3 Cable and Adapter Information Connect Inputs Connect all analog DVI and SDI input sources to the PDS Chapter 3 Signal Installation Connect Outputs Connect the output s of the PDS to your projector s or other target devices Chapter 3 Signal Installation Power On Turn on power to the PDS your projector s and to all peripheral equipment Chapter 4 Power Up Initialization Factory Reset When using a PDS for the first time perform a factory reset Chapter 4 Factory Reset Menu Launch GUI Optional Connect your laptop to the PDS log onto the PDS using its IP address and launch the GUI Chapter 5 GUI Operations Set Output Format Set the desired output resolution and frame rate Chapter 4 Output Format Enable Test Pattern Turn on a test pattern verify an image and adjust as required When complete turn off the pattern Chapter 4 Test Pattern Save Output Configuration After completing all output adjustments save the output configuration
3. ll iter i Sizing Adjust Program If the input is not valid Invalid Signal Timing Adjust Firmware Upgrade is shown USB Upgrade e Next Input Type Indicates next Program input Eee ee sae type plus HDCP status if applicable a i e Next Input Format Indicates next Program Save Config input format meee Geni Recall Config Delete Config For HDCP sources ensure the Output Display device is HDCP compliant MIUN Otherwise the display device will be Breakout Cables for Analog Inputs blacked when protected content is EE E ETR F E E aaa selected to be shown on that output Use this table to Deas E ete Wire Color Video Y C YPbPr Sync on Green Comp Sync Separate H V i connect various source oi Cee ae aed i For complete details on formats to the PDS R v Pr 4 4 4 all installation setup e To display the Setup Menu from the using the system s a F Fi Pim F F F and operating Status Menu press SEL analog input connectors procedures refer to the e To return to the Status Menu from Inputs 1 8 B Chrom v Pb w e PDS User s Guide any point in the Setup Menu press y 7 ESC repeatedly P P N 26 1204004 00 Rev 01
4. s The connector s analog pins can be SDI source Both have the same analog preview for communications with PDS Use the Use breakout cables as required accessed with a breakout cable or a resolution and both can be monitor Ethernet Menu and Serial Setup Menu to See below for details DVI to HD 15 adapter used simultaneously Only on PDS 902 set parameters Use Ethernet connector to Inputs 7 and 8 not on PDS 701 run web based GUI Input 7 Input 8 Preview AC GOSEG8E0 p s S 200000001 go P Va A D i BBgppppp 09 AA Seeeeeec 02 Ly Connect to Input 5 Input 6 ZN PROGRAM AC power 1 po020000 A N p00002020 PN 00220000 A rce soooocee lan ajajajaja la J OMaria source 4 Goeeeeee Ss gt Geeeeeee l d soocoooel s d ETHERNET VIDEO INPUTS SERIAL Status Menu lt Program Input Type lt Program Input Format lt Next Input Type ATA TS lt Next Input Format Ee so Sample Status Menu Adjust On p l l Onon PSs Save Pgm to Logo Serial Setup Web Address e Input Type Specifies the type of input signal y Delete Logo input EDID currently on Program DVI Cable Equal i a Reset All Save EDID P e Input Format Indicates video format on Reset A
5. sim PDS Series Visibly yours Quick Start Guide Barco Inc Toll Free 1 888 414 7226 Fax 1 916 859 2515 Technical Support 1 866 374 7878 Website www barco com Menu Display Use ADJUST knob plus SEL and ESC buttons to navigate menus Adjust e Counter clockwise scroll down menu tree or decrement values e Clockwise scroll up menu tree or increment values SEL Press to enter a menu change or accept a parameter or answer SDI Yes to a query Press to exit a menu without making changes cancel an operation or answer No to a query ESC Press to freeze or un freeze current Program source Lit solid frozen Inputs Section Sources 1 4 Analog Sources 5 8 DVI or Analog 3G HD SD SDI LOGO Full screen capture sources 7 8 not on PDS 701 FRZ BLACK Press to pend or initiate a black transition Black Auto Take mode affects function User Preferences Blinking Pending Lit solid Black on Program Button States Off Input not selected Blinking Input pending for transition Lit solid Input on Program PDS 902 to adjust the transition time LOGO NOTE TAKE Press to mix the selected input After each to Program or to execute a pend
Download Pdf Manuals
Related Search