Avaya How to Use the Wall-Mounting Brackets Kit User's Manual
Contents
1. 9754FA 2 Fasten the brackets to the module using two flathead screws in each bracket 9758FA To complete the module installation go to Attaching the module to the wall on page 10 Installing two modules Note The bracket with the round opening goes on the right side of the module where the round fan vents are located 1 Set each bracket with the top tabs of the bracket against the recessed mounting holes in the bottom of one module 9759FA 2 Fasten the brackets to the bottom of the module using two flathead screws in each bracket 9760FA 3 Set the second module on its back panel Slide the first module with attached brackets over the second module 9761FA 4 Using two flathead screws in each bracket fasten the brackets to the bottom of the second module Attaching the module to the wall Note Attach the module to the wall with the front panel facing up Any other position compromises safety standards 1 Using the dimensions of the module you intend to mount drill pilot holes in the wall for the mounting screws i o 9763EA 2 Insert the mounting screws partway into the wall foes 9764FB Note If you are attaching the module to a hollow wall use expanding wall anchors 3 Set the module in place over the screws Tighten the screws to secure the module to the wall 4 Attach network cables Use plastic cable clamps to support the ca2. Part No 212687 A February 2002 4401 Great America Parkway Santa Clara CA 95054 How to Use the Wall Mounting Brackets Kit NORTEL NETWORKS 212687 A x Copyright 2001 Nortel Networks All rights reserved February 2002 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Nortel Networks NA Trademarks NORTEL NETWORKS is a trademark of Nortel Networks Nortel Networks is a trademark of Nortel Networks All other trademarks and registered trademarks are the property of their respective owners Statement of Conditions In the interest of improving internal design operational function and or reliability Nortel Networks NA Inc reserves the right to make changes to the products described in this document without notice Nortel Networks NA Inc does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Introduction The optional wall mounting brackets kit provides you with an alternate method of installing your Nortel Networks module Contact your Nortel Networks representative for information about wh
3. bles and route them away from fans and vents on the switch 9766FA Do not let cables hang freely from the port connectors The weight of these cables can damage the connectors 11 How to get help If you purchased a service contract for your Nortel Networks product from a distributor or authorized reseller contact the technical support staff for that distributor or reseller for assistance If you purchased a Nortel Networks service program contact one of the following Nortel Networks Technical Solutions Centers Technical Solutions Center Telephone EMEA 33 4 92 966 968 North America 800 2LANWAN or 800 252 6926 Asia Pacific 61 2 9927 8800 China 800 810 5000 An Express Routing Code ERC is available for many Nortel Networks products and services When you use an ERC your call is routed to a technical support person who specializes in supporting that product or service To locate an ERC for your product or service go to the www 2 nortelnetworks com URL and click ERC at the bottom of the page
4. ich Nortel Networks products use the wall mounting brackets This guide includes information about the following topics e Before you begin next e Package contents on page 4 e Installing the module on a wall on page 5 e Installing a single module on page 6 e Installing two modules on page 8 e Attaching the module to the wall on page 10 e How to get help on page 12 Before you begin Make sure the area where you will install and use the module meets these environmental requirements e Ambient temperature between 41 and 104 F 5 and 40 C e Relative humidity between 5 and 85 noncondensing No nearby heat sources such as hot air vents or direct sunlight e No nearby sources of severe electromagnetic noise e No excessive dust e Adequate power source within six feet one 15 Amp circuit required for each power supply e Atleast 2 inches 5 08 cm on each side of the switch unit for ventilation e Adequate space at the front and rear of the switch for access to cables Package contents SD SD SS a6 DA D oD oa ap oD 10631FA Wall mounting hardware Wall mount brackets Screws for attaching brackets to the switch Safety cover to use with a cascade module in a wall installation Note Nortel Networks does not include screws for attaching the module to a wall Because wall compositions vary at different sites Nortel Networks recommends that an expe
5. rienced maintenance person choose the appropriate wall mounting hardware to install the module safely Installing the module on a wall Required tools and material Phillips screwdriver for attaching brackets to the module Four screws appropriate to the composition of the wall where you will install the module Screwdriver appropriate to your wall mounting hardware for attaching the module to the wall Recommended sheet of 1 2 inch plywood attached to the wall where you will install the module Expanding wall anchors if you are installing the module on a hollow wall Optional drill for making pilot holes in the wall Plastic cable clamps to route and support the port cables after you install the switch Be aware of the following considerations when you plan the wall installation To install two modules remember to consider their combined weight Attached cables increase the weight of the installation and the accumulated weight of these cables increases with the height of the mounting location Place the module at a height that allows you to see the LEDs Remove any installed rack mount brackets or rubber footpads from the module Installing a single module Note The bracket with the round opening goes on the right side of the module where the round fan vents are located 1 Slip a bracket over each side of the module with the bracket tabs against the recessed mounting holes on the bottom of the switch y
Download Pdf Manuals
Related Search