Avaya E7S/7S User's Manual
Contents
1. E7S 7S Expansion Module Supplement Part No 304137 A Rev 00 November 1998 sa Bay Networks sa Bay Networks 4401 Great America Parkway 8 Federal Street Santa Clara CA 95054 Billerica MA 01821 Copyright 1998 Bay Networks Inc All rights reserved Printed in the USA November 1998 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Bay Networks Inc Trademarks AN Quick2Config and Bay Networks are registered trademarks and Advanced Remote Node ANH ARN ASN BayRS BayStack BayStream BCC and the Bay Networks logo are trademarks of Bay Networks Inc Statement of Conditions In the interest of improving internal design operational function and or reliability Bay Networks Inc reserves the right to make changes to the products described in this document without notice Bay Networks Inc does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein USA Requirements Only Federal Communications Commission FCC Compliance Notice Radio Frequency Notice Note This equipment has been tested and f2. Code for the E7S Module Router Type Code Type Minimum Version Directory File Name ARN Boot 1 23 arn_proms arnboot exe Diagnostic 2 16 arn_proms arndiag exe For information about upgrading PROM see Upgrading Routers to BayRS Version 13 10 304137 A Rev 00 1 E7S 7S Expansion Module Supplement 7S Router Reguirements Table 1 shows the minimum levels of boot and diagnostic programmable read only memory PROM code required for an ARN multiserial expansion module Table 2 PROM Diagnostic and Boot Code for the 7S Module Router Type Code Type Minimum Version Directory File Name ARN Boot 1 23 arn proms arnboot exe Diagnostic 2 16 arn proms arndiag exe For information about upgrading PROM see Upgrading Routers to BayRS Version 13 10 Attaching Cables This section shows the cable connections for the E7S and 7S expansion modules Connect the appropriate cabling to the new Ethernet and serial interfaces Refer to the Cable Guide for the cables available from Bay Networks Figure 1 shows the Ethernet cable connection to an E7S expansion module Expansion module 10BASE T interface U soneri withNT1 EB BayStack Advanced Remote Node MR Bay Networks To Ethernet Ethernet 10BASE T c
3. a BayStack ARN Router for the sequence of front panel LED activity that should occur Interpreting the E7S Ethernet LEDs Table 3 describes the LEDs for the E7S module s Ethernet interface Table 3 LED Tx Transmit Ethernet Interface LEDs Meaning Lights when the ARN is transmitting data over the network Rx Receive Lights when the ARN is receiving data from the network CL Collision Lights when the ARN detects a collision on the network These LEDs will blink on and off during diagnostic testing but they will not stay on to indicate data transfer until you have configured the Ethernet interface Interpreting the E7S and 7S Serial LEDs Each E7S and 7S received line signal detection RLSD LED lights when carrier detect is present on the WAN port 304137 A Rev 00 Using the E7S and 7S Expansion Modules Completing Software Configuration Once you have successfully installed an E7S or 7S expansion module complete the following software configuration tasks using instructions found in your BayRS documentation Configuration Task Location of Instructions Connect the ARN to the network One of the following Installing and Operating BayStack ARN Routers e Configuring BayStack Remote Access Modify the ARN configuration file to add the E7S expansion module and enable default software services Any of the following e Configuring and Managing Routers with Sit
4. but if advance notice is not practical you will be notified as soon as possible and will be informed of your right to file a complaint with the FCC 4 If you experience trouble with the unit please contact the Bay Networks Technical Solutions Center in your area for service or repairs Repairs should be performed only by service personnel authorized by Bay Networks Inc United States 1 800 2LAN WAN Valbonne France 33 4 92 96 69 68 Sydney Australia 61 2 9927 8800 Tokyo Japan 81 3 5402 0180 5 You are required to notify the telephone company when you disconnect the unit from the network 304137 A Rev 00 V Bay Networks Inc Software License Agreement NOTICE Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre enabled software each of which is referred to as Software in this Agreement BY COPYING OR USING THE SOFTWARE YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH BAY NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE If you do not accept these terms and conditions return the product unused and in the original shipping container within 30 days of purchase to obtain a credit for the full purchase price 1 License Grant Bay Networks Inc Bay Networks grants the end user of the Software Licensee a personal nonexclusive nontransferable lice
5. interface The termination on an interface may consist of any combination of devices subject only to the requirement 304137 A Rev 00 iii that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 The REN is located on the FCC Rules Part 68 label located on the bracket of the module or on the back of the unit Canada CS 03 Regles et reglements Avis L tiquette d Industrie Canada identifie le mat riel homologu Cette tiquette certifie que le mat riel est conforme aux normes de protection d exploitation et de s curit des r seaux de t l communications comme le prescrivent les documents concernant les exigences techniques relatives au mat riel terminal Le Minist re n assure toutefois pas que le mat riel fonctionnera la satisfaction de l utilisateur Avant d installer ce mat riel l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l entreprise locale de t l communication Le mat riel doit galement tre install en suivant une m thode accept e de raccordement L abonn ne doit pas oublier qu il est possible que la conformit aux conditions nonc es ci dessus n emp che pas la d gradation du service dans certaines situations Les r parations de mat riel homologu doivent tre coordonn es par un repr sentant d sign par le fournisseur L entreprise de t l communications peut demander l utilisateur de d brancher un appareil la suite de r p
6. URPOSE Licensee is responsible for the security of vi 304137 A Rev 00 its own data and information and for maintaining adeguate procedures apart from the Software to reconstruct lost or altered files data or programs 4 Limitation of liability IN NO EVENT WILL BAY NETWORKS OR ITS LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE EVEN IF BAY NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL THE LIABILITY OF BAY NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT EXCEED THE PRICE PAID TO BAY NETWORKS FOR THE SOFTWARE LICENSE 5 Government Licensees This provision applies to all Software and documentation acquired directly or indirectly by or on behalf of the United States Government The Software and documentation are commercial products licensed on the open market at market prices and were developed entirely at private expense and without the use of any U S Government funds The license to the U S Government is granted only with restricted rights and use duplication or disclosure by the U S Government is subject to the restrictions set forth in subparagraph c 1 of the Commercial Computer Software Restricted Rights clause of FAR 52 227 19 and the limitations set out in this license for ci
7. ables network ARN0094A Figure 1 E7S Ethernet Interface Cable Connection 2 304137 A Rev 00 Using the E7S and 7S Expansion Modules Figure 2 shows a serial cable connection to an E7S expansion module y s a n BaseT RLS09 coms RLSO7 1 sonar F O E S withNT1 4 a 2 4 m RLSOS l com O 2 5 A z me z LE E Pay Networks Teer BayStack Advanced Remote Node RS 232 RS 422 Y O RS 530 V 28 V 35 or X 21 interface ARNO096A Figure 2 E7S Serial Interface Cable Connection Figure 3 shows a serial cable connection to a 7S expansion module D Bt O RLSO9 COM9 RLSO7 ISON BRI S a COM O I SER a Bay Networks Teint O BayStack Advanced Remote Node RS 232 RS 422 O RS 530 V 28 V 35 or X 21 interface ARNO095A Figure 3 7S Serial Interface Cable Connection 304137 A Rev 00 3 E7S 7S Expansion Module Supplement Ensuring a Successful Installation After reconnecting the ARN to the network you can ensure a successful upgrade by checking the diagnostic LEDs on the front panel of the base module See Installing an Expansion Module in
8. arations ou de modifications effectu es par l utilisateur ou cause de mauvais fonctionnement Pour sa propre protection l utilisateur doit s assurer que tous les fils de mise la terre de la source d nergie lectrique des lignes t l phoniques et des canalisations d eau m talliques s il y en a sont raccord s ensemble Cette pr caution est particuli rement importante dans les r gions rurales Avertissement L utilisateur ne doit pas tenter de faire ces raccordements lui m me il doit avoir recours un service d inspection des installations lectriques ou un lectricien selon le cas Avis Veuillez prendre note que pour tout appareillage supportant des lignes de type loopstart l indice d quivalence de la sonnerie IES assign 4 chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent tre raccord s une interface La terminaison d une interface t l phonique peut consister en une combinaison de quelques dispositifs la seule condition que la somme d indices d quivalence de la sonnerie de tous les dispositifs n exc de pas 5 Le REN figure sur l tiquette FCC Rules Part 68 situ e sur le support du module ou arri re de unit FCC Part 68 Compliance Statement This equipment complies with Part 68 of FCC Rules All direct connections to telephone network lines must be made using standard plugs and jacks compliant with FCC Part 68 Please note the following 1 You are requi
9. d in the appropriate Terminal Equipment Technical Requirements document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent the degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate Notice For equipment using loopstart lines please note that the Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone
10. e Manager e Using the Bay Command Console e Configuring Your Router Using the Quick2Config Tool Configure line services Configuring WAN Line Services Configure WAN protocol services Any of the BayRS WAN or system suite guides including e Configuring IP Services e Configuring Frame Relay Services e Configuring X 25 Services e Configuring PPP Services For the latest information be sure to review the release notes and document change notice for your version of the BayRS software 304137 A Rev 00
11. e sum of the RENS of all devices should not exceed 5 0 To be certain of the number of devices you can connect to your line you should call your local telephone company to determine the maximum REN for your calling area When you request ISDN U Interface Service you must provide the telephone company with The Facility Interface Code 02185 The Service Order Code s SOC 6 0F The required Universal Service Order Code USOC jack RJ49C When you request ISDN S T Interface Service you must provide the telephone company with The Service Order Code s SOC 6 0N The make model number and FCC Registration number of the NT1 Note ISDN S T cannot be directly connected to the network When you request Primary Rate ISDN Service you must provide the telephone company with The Facility Interface Code 04DU9 1SN 1 544 MB ESF framing format with B8ZF coding The Service Order Code s SOC 6 0F The required Universal Service Order Code USOC jack RJ48C 2 Your telephone company may make changes to its facilities equipment operations or procedures that could affect the proper functioning of your equipment The telephone company will notify you in advance of such changes to give you an opportunity to maintain uninterrupted telephone service 3 Ifthe unit causes harm to the telephone network the telephone company may temporarily discontinue your service If possible they will notify you in advance
12. mages in any form solely by reason of the termination of this license 8 Export and Re export Licensee agrees not to export directly or indirectly the Software or related technical data or information without first obtaining any required export licenses or other governmental approvals Without limiting the foregoing Licensee on behalf of itself and its subsidiaries and affiliates agrees that it will not without first obtaining all export licenses and approvals required by the U S Government i export re export transfer or divert any such Software or technical data or any direct product thereof to any country to which such exports or re exports are restricted or embargoed under United States export control laws and regulations or to any national or resident of such restricted or embargoed countries or ii provide the Software or related technical data or information to any military end user or for any military end use including the design development or production of any chemical nuclear or biological weapons 9 General If any provision of this Agreement is held to be invalid or unenforceable by a court of competent jurisdiction the remainder of the provisions of this Agreement shall remain in full force and effect This Agreement will be governed by the laws of the state of California Should you have any questions concerning this Agreement contact Bay Networks Inc 4401 Great America Parkway PO Box 58185 Santa Clara Calif
13. nse a to use the Software either on a single computer or if applicable on a single authorized device identified by host ID for which it was originally acguired b to copy the Software solely for backup purposes in support of authorized use of the Software and c to use and copy the associated user manual solely in support of authorized use of the Software by Licensee This license applies to the Software only and does not extend to Bay Networks Agent software or other Bay Networks software products Bay Networks Agent software or other Bay Networks software products are licensed for use under the terms of the applicable Bay Networks Inc Software License Agreement that accompanies such software and upon payment by the end user of the applicable license fees for such software 2 Restrictions on use reservation of rights The Software and user manuals are protected under copyright laws Bay Networks and or its licensors retain all title and ownership in both the Software and user manuals including any revisions made by Bay Networks or its licensors The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals Licensee may not modify translate decompile disassemble use for any competitive analysis reverse engineer distribute or create derivative works from the Software or user manuals or any copy in whole or in part Except as expressly provided in this Agreement Licensee may not copy or tra
14. nsfer the Software or user manuals in whole or in part The Software and user manuals embody Bay Networks and its licensors confidential and proprietary intellectual property Licensee shall not sublicense assign or otherwise disclose to any third party the Software or any information about the operation design performance or implementation of the Software and user manuals that is confidential to Bay Networks and its licensors however Licensee may grant permission to its consultants subcontractors and agents to use the Software at Licensee s facility provided they have agreed to use the Software only in accordance with the terms of this license 3 Limited warranty Bay Networks warrants each item of Software as delivered by Bay Networks and properly installed and operated on Bay Networks hardware or other equipment it is originally licensed for to function substantially as described in its accompanying user manual during its warranty period which begins on the date Software is first shipped to Licensee If any item of Software fails to so function during its warranty period as the sole remedy Bay Networks will at its discretion provide a suitable fix patch or workaround for the problem that may be included in a future Software release Bay Networks further warrants to Licensee that the media on which the Software is provided will be free from defects in materials and workmanship under normal use for a period of 90 days from the date Soft
15. ornia 95054 8185 LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT UNDERSTANDS IT AND AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS LICENSEE FURTHER AGREES THAT THIS AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN BAY NETWORKS AND LICENSEE WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS AGREEMENT NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST BAY NETWORKS UNLESS BAY NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT 304137 A Rev 00 vii Using the E7S and 7S Expansion Modules This document supplements one of the following guides e Installing and Operating a BayStack ARN Router e Installing an Expansion Module in a BayStack ARN Router Follow the hardware installation steps in the guide for your router Refer to this document for information specific to the ARN Ethernet multiserial expansion module E7S and the multiserial expansion module 7S Verifying Router Requirements The tables in this section show the minimum levels of boot and diagnostic programmable read only memory PROM code required for the E7S and 7S expansion modules E7S Router Requirements Table 1 shows the minimum levels of boot and diagnostic programmable read only memory PROM code required for an ARN Ethernet multiserial expansion module Table 1 PROM Diagnostic and Boot
16. ound to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy If it is not installed and used in accordance with the instruction manual it may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense European Requirements Only EN 55 022 Statement This is to certify that the Bay Networks E7S 7S Expansion Module is shielded against the generation of radio interference in accordance with the application of Council Directive 89 336 EEC Article 4a Conformity is declared by the application of EN 55 022 Class A CISPR 22 Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be reguired to take appropriate measures EC Declaration of Conformity This product conforms or these products conform to the provisions of Council Directive 89 336 EEC and 73 23 EEC The Declaration of Conformity is available on the Bay Networks World Wide Web site at www baynetworks com ji 304137 A Rev 00 Japan Nippon Regui
17. red to request service from the telephone company before you connect the unit to a network When you request service you must provide the telephone company with the following data When you request T1 Service you must provide the telephone company with The Facility Interface Code Provide the telephone company with all the codes below 04DU9 BN 1 544 MB D4 framing format O4DU9 DN 1 544 MB D4 framing format with B8ZF coding 04DU9 1 KN 1 544 MB ESF framing format 04DU9 1SN 1 544 MB ESF framing format with BSZF coding 04DU9 1ZN 1 544 MB ANSI ESF and ZBTSI without line power The telephone company will select the code it has available The Service Order Code s SOC 6 0F The required Universal Service Order Code USOC jack RJ48C When you request 56K 64K Service you must provide the telephone company with The Facility Interface Code 04DU5 56 64 The Service Order Code s SOC 6 0F The required Universal Service Order Code USOC jack RJ48S iv 304137 A Rev 00 When you request V 34 Service you must provide the telephone company with The required Universal Service Order Code USOC jack RJ11C The make model number Ringer Equivalence Number REN and FCC Registration number of the unit The REN helps you determine the number of devices you can connect to your telephone line and still have all of those devices ring when your number is called In most but not all areas th
18. rements Only Voluntary Control Council for Interference VCCI Statement TD TAL EE EE A TRA VCCI off LAS TA AREA TT CO RES R T MTSEMR HEeESIERITIEHMEHET TORAKA T U T Dk Ekehaar ANET Voluntary Control Council for Interference VCCI Statement This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions Canada Requirements Only Canadian Department of Communications Radio Interference Regulations This digital apparatus E7S 7S Expansion Module does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications R glement sur le brouillage radio lectrique du minist re des Communications Cet appareil num rique E7S 7S Expansion Module respecte les limites de bruits radio lectriques visant les appareils num riques de classe A prescrites dans le R glement sur le brouillage radio lectrique du minist re des Communications du Canada Canada CS 03 Rules and Regulations Notice The Industry Canada label identifies certified equipment This certification means that the equipment meets telecommunications network protective operational and safety requirements as prescribe
19. vilian agencies and subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause of DFARS 252 227 7013 for agencies of the Department of Defense or their successors whichever is applicable 6 Use of Software in the European Community This provision applies to all Software acquired for use within the European Community If Licensee uses the Software within a country in the European Community the Software Directive enacted by the Council of European Communities Directive dated 14 May 1991 will apply to the examination of the Software to facilitate interoperability Licensee agrees to notify Bay Networks of any such intended examination of the Software and may procure support and assistance from Bay Networks 7 Term and termination This license is effective until terminated however all of the restrictions with respect to Bay Networks copyright in the Software and user manuals will cease being effective at the date of expiration of the Bay Networks copyright those restrictions relating to use and disclosure of Bay Networks confidential information shall continue in effect Licensee may terminate this license at any time The license will automatically terminate if Licensee fails to comply with any of the terms and conditions of the license Upon termination for any reason Licensee will immediately destroy or return to Bay Networks the Software user manuals and all copies Bay Networks is not liable to Licensee for da
20. ware is first shipped to Licensee Bay Networks will replace defective media at no charge if it is returned to Bay Networks during the warranty period along with proof of the date of shipment This warranty does not apply if the media has been damaged as a result of accident misuse or abuse The Licensee assumes all responsibility for selection of the Software to achieve Licensee s intended results and for the installation use and results obtained from the Software Bay Networks does not warrant a that the functions contained in the software will meet the Licensee s requirements b that the Software will operate in the hardware or software combinations that the Licensee may select c that the operation of the Software will be uninterrupted or error free or d that all defects in the operation of the Software will be corrected Bay Networks is not obligated to remedy any Software defect that cannot be reproduced with the latest Software release These warranties do not apply to the Software if it has been i altered except by Bay Networks or in accordance with its instructions ii used in conjunction with another vendor s product resulting in the defect or iii damaged by improper environment abuse misuse accident or negligence THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR P
Download Pdf Manuals
Related Search