Avaya a Power Module in the Passport 5430 Multiservice Access Switch User's Manual
Contents
1. Caution Electrostatic discharge can damage hardware You must wear the antistatic wrist strap on your arm whenever you handle printed circuit boards Refer to the instructions enclosed wtih your antistatic wrist strap to attach it 2 Remove the power supply filler panel For instructions see Removing and Installing a Power Supply Filler Panel on page 14 3 Grasp the handle and push the power supply into the slot along the side guides and gently insert the supply Figure 4 10 Captive screw FBR0009A Figure 4 Removing or Installing a Power Supply 4 Using a flat tip screwdriver tighten the captive screw until the power supply is seated firmly 11 When you insert an operational second power supply into the Passport 5430 with the power on the PS2 LED on the system processor module turns on At the same time the Passport 5430 automatically redistributes the load between the two power supplies 5 Connect to the AC power source For instructions see Connecting to the AC Power Source on page 17 6 Turnon the power supply power switch Replacing a Power Supply To replace a power supply Caution To maintain proper cooling never operate the Pass port 5430 with an empty power supply slot If you are replac ing a failed second power supply and you do not have a power filler panel leave the fail2. 96 69 68 Sydney Australia 61 2 9927 8800 Tokyo Japan 81 3 5740 1700 About the Power Supply The Passport 5430 contains one or two AC input power supplies Figure 1 shows the location of the power supplies in the Passport 5430 Power switch 2 NORTEL FBR0031A Figure 1 Location of the Power Supplies in the Passport 5430 The Passport 5430 ships with a single AC power supply You can install a second power supply for redundancy and high availability operation Figure 2 shows an AC input power supply FBR0050A Figure 2 Passport 5430 Power Supply The operating system generates an event message in response to any change in the status of a power module These messages identify the power supply by its slot From the back of the Passport 5430 power supply 1 is on the left and power supply slot 2 is on the right Checking Status Indicators Figure 3 shows the location of the power supply LEDs on the system processor card e PC Siot 1 PCI Slot 2 2 PGISiota FBROO24A Figure 3 Passport 5430 System Processor Card Diagnostic LEDs Tabl
3. es ci dessus n emp che pas la d gradation du service dans certaines situations Les r parations de mat riel homologu doivent tre coordonn es par un repr sentant d sign par le fournisseur L entreprise de t l communications peut demander l utilisateur de d brancher un appareil la suite de r parations ou de modifications effectu es par l utilisateur ou cause de mauvais fonctionnement Pour sa propre protection l utilisateur doit s assurer que tous les fils de mise la terre de la source d nergie lectrique des lignes t l phoniques et des canalisations d eau m talliques s il y en a sont raccord s ensemble Cette pr caution est particuli rement importante dans les r gions rurales Avertissement L utilisateur ne doit pas tenter de faire ces raccordements lui m me il doit avoir recours un service d inspection des installations lectriques ou un lectricien selon le cas vi Avis Veuillez prendre note que pour tout appareillage supportant des lignes de type loopstart l indice d quivalence de la sonnerie IES assign chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent tre raccord s une interface La terminaison d une interface t l phonique peut consister en une combinaison de quelques dispositifs la seule condition que la somme d indices d quivalence de la sonnerie de tous les dispositifs n exc de pas 5 Le REN figure sur l tiquette FCC Rul
4. radio lectrique du minist re des Communications du Canada Canada CS 03 Rules and Regulations Notice The Industry Canada label identifies certified equipment This certification means that the equipment meets telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent the degradation of service in some situations Canada Requirements Only Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections thems
5. un environnement domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors l utilisateur de prendre les mesures sp cifiques appropri es EC Declaration of Conformity This product conforms or these products conform to the provisions of Council Directive 89 336 EEC and 73 23 EEC The Declaration of Conformity is available on the Nortel Networks World Wide Web site at http libra2 corpwest baynetworks com cgi bin ndCGI exe Doc View Japan Nippon Requirements Only Voluntary Control Council for Interference VCCI Statement COREL VCCI OAM CORES SEARCH LAN CEMAOST ET Taiwan Requirements Bureau of Standards Metrology and Inspection BSMI Statement ERRAK GE ERER RHEA T S RH ATE CURR HAE SHERRAN Canada Requirements Only Canadian Department of Communications Radio Interference Regulations This digital apparatus Passport 5430 does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications R glement sur le brouillage radio lectrique du minist re des Communications Cet appareil num rique Passport 5430 respecte les limites de bruits radio lectriques visant les appareils num riques de classe A prescrites dans le R glement sur le brouillage
6. 1 will apply to the examination of the Software to facilitate interoperability Licensee agrees to notify Nortel Networks of any such intended examination of the Software and may procure support and assistance from Nortel Networks 7 Term and termination This license is effective until terminated however all of the restrictions with respect to Nortel Networks copyright in the Software and user manuals will cease being effective at the date of expiration of the Nortel Networks copyright those restrictions relating to use and disclosure of Nortel Networks confidential information shall continue in effect Licensee may terminate this license at any time The license will automatically terminate if Licensee fails to comply with any of the terms and conditions of the license Upon termination for any reason Licensee will immediately destroy or return to Nortel Networks the Software user manuals and all copies Nortel Networks is not liable to Licensee for damages in any form solely by reason of the termination of this license 8 Export and Re export Licensee agrees not to export directly or indirectly the Software or related technical data or information without first obtaining any required export licenses or other governmental approvals Without limiting the foregoing Licensee on behalf of itself and its subsidiaries and affiliates agrees that it will not without first obtaining all export licenses and approvals required by the U S Gov
7. ANCE OF THE SOFTWARE EVEN IF NORTEL NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL THE LIABILITY OF NORTEL NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT EXCEED THE PRICE PAID TO NORTEL NETWORKS FOR THE SOFTWARE LICENSE 5 Government Licensees This provision applies to all Software and documentation acquired directly or indirectly by or on behalf of the United States Government The Software and documentation are commercial products licensed on the open market at market prices and were developed entirely at private expense and without the use of any U S Government funds The license to the U S Government is granted only with restricted rights and use duplication or disclosure by the U S Government is subject to the restrictions set forth in subparagraph c 1 of the Commercial Computer Software Restricted Rights clause of FAR 52 227 19 and the limitations set out in this license for civilian agencies and subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause of DFARS 252 227 7013 for agencies of the Department of Defense or their successors whichever is applicable xi 6 Use of Software in the European Community This provision applies to all Software acquired for use within the European Community If Licensee uses the Software within a country in the European Community the Software Directive enacted by the Council of European Communities Directive dated 14 May 199
8. Installing a Power Supply Filler Panel Nortel Networks ships the Passport 5430 with a filler panel in the power supply slot reserved for the second power supply Before you can install a second power supply you must remove the power supply filler panel for instructions see the next section Removing a Power Supply Filler Panel If you remove a power supply from the Passport 5430 without replacing it you must install a power filler panel to maintain the proper cooling airflow For instructions see Installing a Power Supply Filler Panel on page 16 Removing a Power Supply Filler Panel To remove a power supply filler panel 1 Using a flat tip screwdriver loosen the captive screw that fastens the power supply filler panel to the chassis until the filler panel disengages Figure 5 14 Figure 5 Removing a Power Supply Filler Panel FBR0059A 2 Pull the power supply filler panel away from the Passport 5430 Caution To maintain proper cooling never operate the Pass port 5430 with an empty power supply slot Save the filler panel to cover the slot in case you need to operate the Passport 5430 with a power supply removed Installing a Power Supply Filler Panel If you remove a power supply from the Passport 5430 without replacing it you must install a power supply filler panel to maintain the proper cooling airflow To install a power supply fill
9. KS UNLESS NORTEL NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT xiii Contents Preface 1 Before You Begin1 Text Conventions1 Acronyms2 Hard Copy Technical Manuals2 How to Get Help3 About the Power Supply 4 Checking Status Indicators6 AC Input Electrical Requirements8 Adding or Replacing a Power Supply 9 Adding a Second Power Supply10 Replacing a Power Supply12 Removing and Installing a Power Supply Filler Panel14 Removing a Power Supply Filler 1 4 Installing a Power Supply Filler Panel16 Connecting to the Power Source 17 Connecting to the AC Power Source17 XV Preface EN In this guide the Passport 5430 Multiservice Access Switch is referred to as the Passport 5430 Before You Begin This guide is intended for qualified service personnel who need to add or replace a Passport 5430 power supply A qualified service person should have appropriate technical training and experience and be aware of the hazards involved in installing and replacing power supplies Before installing the Passport 5430 ensure that all network wiring had been installed on the premises using standard cable system practices Text Conventions This guide uses the following text conventions italic text Indicates new terms and book titles Acronyms EIA Electronic Industries Association LED light emitting diode Hard Copy Technical Manuals You can print sel
10. Part No 306622 A Rev 00 January 2000 4401 Great America Parkway Santa Clara CA 95054 Installing a Power Module in the Passport 5430 Multiservice Access Switch NORTEL NETWORKS Copyright 2000 Nortel Networks All rights reserved Printed in the USA January 2000 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Nortel Networks NA Inc Trademarks NORTEL NETWORKS is a trademark of Nortel Networks BayRS BCC and Passport are trademarks of Nortel Networks All other trademarks and registered trademarks are the property of their respective owners Statement of Conditions In the interest of improving internal design operational function and or reliability Nortel Networks NA Inc reserves the right to make changes to the products described in this document without notice Nortel Networks NA Inc does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein USA Requirements Only Federal Communications Commission FCC Compliance Notice Radio Fre quency Notice Note This equipment has been tested and f
11. contained in the software will meet the Licensee s requirements b that the Software will operate in the hardware or software combinations that the Licensee may select c that the operation of the Software will be uninterrupted or error free or d that all defects in the operation of the Software will be corrected Nortel Networks is not obligated to remedy any Software defect that cannot be reproduced with the latest Software release These warranties do not apply to the Software if it has been i altered except by Nortel Networks or in accordance with its instructions ii used in conjunction with another vendor s product resulting in the defect or iii damaged by improper environment abuse misuse accident or negligence THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Licensee is responsible for the security of its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or altered files data or programs 4 Limitation of liability IN NO EVENT WILL NORTEL NETWORKS OR ITS LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORM
12. cts are licensed for use under the terms of the applicable Nortel Networks NA Inc Software License Agreement that accompanies such software and upon payment by the end user of the applicable license fees for such software 2 Restrictions on use reservation of rights The Software and user manuals are protected under copyright laws Nortel Networks and or its licensors retain all title and ownership in both the Software and user manuals including any revisions made by Nortel Networks or its licensors The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals Licensee may not modify translate decompile disassemble use for any competitive analysis reverse engineer distribute or create derivative works from the Software or user manuals or any copy in whole or in part Except as expressly provided in this Agreement Licensee may not copy or transfer the Software or user manuals in whole or in part The Software and user manuals embody Nortel Networks and its licensors confidential and proprietary intellectual property Licensee shall not sublicense assign or otherwise disclose to any third party the Software or any information about the operation design performance or implementation of the Software and user manuals that is confidential to Nortel Networks and its licensors however Licensee may grant permission to its consultants subcontractors and agents to use the Software at L
13. e 1 describes the power supply LEDs Table 1 AC Power Module LEDs LED State Meaning PS1 Off Power off On green Power supply is operating Rapid flashing Power supply failed green PS2 Off Power off On green Redundant power supply optional is operating Rapid flashing green Redundant power supply failed AC Input Electrical Requirements The installation site must meet the following electrical requirements for AC power Table 2 Table 2 Electrical Requirements Input Voltage Range Maximum Input Current 90 264 volts alternating current VAC 1 0 amperes A Table 3 lists the wall receptacle requirements for AC power Table 3 Wall Receptacle Requirements for AC Power Country Receptacle Voltage United States National Electrical Manufacturers Association 100 120 V and Canada NEMA 5 15R standard receptacle Any other Your Passport 5430 distributor attaches the 100 240 V country necessary plug to the power cable and informs you of the receptacle you need Adding or Replacing a Power Supply This chapter describes how to add or replace a Passport 5430 power supply as follows Topic Page Adding a Second Power Supply 10 Replacing a Power Supply 12 Removing and Installing a Power Supply Filler Panel 14 Adding a Second Power Supply To add a second power supply 1 Put on antistatic wrist strap
14. ect the unit from the network Nortel Networks NA Inc Software License Agreement NOTICE Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre enabled software each of which is referred to as Software in this Agreement BY COPYING OR USING THE SOFTWARE YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE If you do not accept these terms and conditions return the product unused and in the original shipping container within 30 days of purchase to obtain a credit for the full purchase price 1 License Grant Nortel Networks NA Inc Nortel Networks grants the end user of the Software Licensee a personal nonexclusive nontransferable license a to use the Software either on a single computer or if applicable on a single authorized device identified by host ID for which it was originally acquired b to copy the Software solely for backup purposes in support of authorized use of the Software and c to use and copy the associated user manual solely in support of authorized use of the Software by Licensee This license applies to the Software only and does not extend to Nortel Networks Agent software or other Nortel Networks software products Nortel Networks Agent software or other Nortel Networks software produ
15. ected technical manuals and release notes free directly from the Internet Go to support baynetworks com library tpubs Find the product for which you need documentation Then locate the specific category and model or version for your hardware or software product Using Adobe Acrobat Reader you can open the manuals and release notes search for the sections you need and print them on most standard printers You can download Acrobat Reader free from the Adobe Systems Web site www adobe com You can purchase selected documentation sets CDs and technical publications through the collateral catalog The catalog is located on the World Wide Web at support baynetworks com catalog html and is divided into sections arranged alphabetically CD ROMs section lists available CDs e Guides Books section lists books on technical topics e Technical Manuals section lists available printed documentation sets How to Get Help If you purchased a service contract for your Nortel Networks product from a distributor or authorized reseller contact the technical support staff for that distributor or reseller for assistance If you purchased a Nortel Networks service program contact one of the following Nortel Networks Technical Solutions Centers Technical Solutions Center Telephone Number Billerica MA 800 2LANWAN 800 252 6926 Santa Clara CA 800 2LANWAN 800 252 6926 Valbonne France 33 4 92
16. ed power supply installed until a replacement power supply is available 1 Turn off the power switch on the power supply you are replacing 12 2 Put on an antistatic wrist strap Caution Electrostatic discharge can damage hardware You must wear the antistatic wrist strap on your arm whenever you handle printed circuit boards Refer to the instructions enclosed with your antistatic wrist strap to attach it 3 Disconnect the power cable from the power connector on the power supply 4 Using a flat tip screwdriver loosen the captive screw that fastens the power supply to the chassis until the power supply disengages Figure 4 5 Grasp the handle and using both hands pull the power supply out of the Passport 5430 You can remove an operational power supply without affecting the operation of the Passport 5430 When you remove a power supply the associated LED PS1 or PS2 on the system processor module turns off and the Passport 5430 automatically redistributes the load to the remaining power supply 6 Grasping the handle guide the replacement power supply into the slot along the side guides and gently insert the supply see Figure 4 on page 11 7 Using a flat tip screwdriver tighten the captive screw until the power supply is seated firmly 8 Connect to the AC power source For instructions see Connecting to the AC Power Source on page 17 9 Turnon the power supply power switch Removing and
17. elves but should contact the appropriate electric inspection authority or electrician as appropriate Notice For equipment using loopstart lines please note that the Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 The REN is located on the FCC Rules Part 68 label located on the bracket of the module or on the back of the unit Canada CS 03 R gles et r glements Avis L tiquette d Industrie Canada identifie le mat riel homologu Cette tiquette certifie que le mat riel est conforme aux normes de protection d exploitation et de s curit des r seaux de t l communications comme le prescrivent les documents concernant les exigences techniques relatives au mat riel terminal Le Minist re n assure toutefois pas que le mat riel fonctionnera la satisfaction de l utilisateur Avant d installer ce mat riel l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l entreprise locale de t l communication Le mat riel doit galement tre install en suivant une m thode accept e de raccordement L abonn ne doit pas oublier qu il est possible que la conformit aux conditions nonc
18. er panel 1 Place the power supply filler panel over the empty power supply slot 2 Using a flat tip screwdriver tighten the captive screw until the power supply filler panel firmly covers the slot 16 Connecting to the Power Source RES This chapter describes how to connect the Passport 5430 to the AC power source Connecting to the AC Power Source To connect the power cable to the Passport 5430 1 Connect a power cable to the power connector on each of the power supplies Figure 6 Power switch Power supplies FBR0031A Figure 6 Connecting the Power Cable to the Passport 5430 2 Connect the remote end of the power cable to a grounded outlet 3 Turn the Passport 5430 on 18
19. ernment i export re export transfer or divert any such Software or technical data or any direct product thereof to any country to which such exports or re exports are restricted or embargoed under United States export control laws and regulations or to any national or resident of such restricted or embargoed countries or ii provide the Software or related technical data or information to any military end user or for any military end use including the design development or production of any chemical nuclear or biological weapons 9 General If any provision of this Agreement is held to be invalid or unenforceable by a court of competent jurisdiction the remainder of the provisions of this Agreement shall remain in full force and effect This Agreement will be governed by the laws of the state of California Should you have any questions concerning this Agreement contact Nortel Networks 4401 Great America Parkway P O Box 58185 Santa Clara California 95054 8185 Xii LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT UNDERSTANDS IT AND AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS LICENSEE FURTHER AGREES THAT THIS AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN NORTEL NETWORKS AND LICENSEE WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS AGREEMENT NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST NORTEL NETWOR
20. es Part 68 situ e sur le support du module ou l arri re de l unit FCC Part 68 Compliance Statement This equipment complies with Part 68 of FCC Rules All direct connections to telephone network lines must be made using standard plugs and jacks compliant with FCC Part 68 Please note the following 1 You are required to request service from the telephone company before you connect the unit to a network When you request service you must provide the telephone company with the following data When you request T1 Service you must provide the telephone company with The Facility Interface Code Provide the telephone company with all the codes below 04DU9 BN 1 544 MB D4 framing format 04DU9 DN 1 544 MB D4 framing format with B8ZF coding 04DU9 1KN 1 544 MB ESF framing format 04DU9 1SN 1 544 MB ESF framing format with B8ZF coding 04DU9 1ZN 1 544 MB ANSI ESF and ZBTSI without line power The telephone company will select the code it has available The Service Order Code s SOC 6 0Y The required Universal Service Order Code USOC jack RJ48C vii viii When you request ISDN U Interface Service you must provide the telephone company with The Facility Interface Code 02155 The Service Order Code s SOC 6 0F The required Universal Service Order Code USOC jack RJ49C When you request ISDN S T Interface Service you must provide the telephone company with The Service O
21. icensee s facility provided they have agreed to use the Software only in accordance with the terms of this license 3 Limited warranty Nortel Networks warrants each item of Software as delivered by Nortel Networks and properly installed and operated on Nortel Networks hardware or other equipment it is originally licensed for to function substantially as described in its accompanying user manual during its warranty period which begins on the date Software is first shipped to Licensee If any item of Software fails to so function during its warranty period as the sole remedy Nortel Networks will at its discretion provide a suitable fix patch or workaround for the problem that may be included in a future Software release Nortel Networks further warrants to Licensee that the media on which the Software is provided will be free from defects in materials and workmanship under normal use for a period of 90 days from the date Software is first shipped to Licensee Nortel Networks will replace defective media at no charge if it is returned to Nortel Networks during the warranty period along with proof of the date of shipment This warranty does not apply if the media has been damaged as a result of accident misuse or abuse The Licensee assumes all responsibility for selection of the Software to achieve Licensee s intended results and for the installation use and results obtained from the Software Nortel Networks does not warrant a that the functions
22. ound to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy If it is not installed and used in accordance with the instruction manual it may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense European Requirements Only EN 55 022 Statement This is to certify that the Nortel Networks Passport 5430 Multiservice Access Switchis shielded against the generation of radio interference in accordance with the application of Council Directive 89 336 EEC Article 4a Conformity is declared by the application of EN 55 022 Class A CISPR 22 Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take appropriate measures Achtung Dieses ist ein Ger t der Funkst rgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkst rungen auftreten in welchen F llen der Benutzer f r entsprechende Gegenma nahmen verantwortlich ist Attention Ceci est un produit de Classe A Dans
23. rder Code s SOC 6 0P The make model number and FCC Registration number of the NT1 Note ISDN S T cannot be directly connected to the network When you request Primary Rate ISDN Service you must provide the telephone company with The Facility Interface Code 04DU9 1SN 1 544 MB ESF framing format with B8ZF coding Service Order Code s SOC 6 0Y The required Universal Service Order Code USOC jack RJ48C Your telephone company may make changes to its facilities equipment operations or procedures that could affect the proper functioning of your equipment The telephone company will notify you in advance of such changes to give you an opportunity to maintain uninterrupted telephone service If the unit causes harm to the telephone network the telephone company may temporarily discontinue your service If possible they will notify you in advance but if advance notice is not practical you will be notified as soon as possible and will be informed of your right to file a complaint with the FCC 4 If you experience trouble with the unit please contact the Nortel Networks Technical Solutions Center in your area for service or repairs Repairs should be performed only by service personnel authorized by Nortel Networks United States 1 800 2LANWAN Valbonne France 33 4 92 96 69 68 Sydney Australia 61 2 9927 8800 Tokyo Japan 81 3 5740 1700 5 You are required to notify the telephone company when you disconn
Download Pdf Manuals
Related Search