Autostart CT-5060 User's Manual
Contents
1. To EXIT Valet Mode 1 With the key in the Ignition switch turn the key to the on RUN IGNITION and then oFF positions 5 times within 10 seconds 2 The Parking Light will flash twice indicating the Module is now out of Valet Mode The LED will turn off Remote Valet This feature will put your vehicle into Valet Mode using the remote transmitter instead of the Valet button as above Note Once the Electronic Valet is activated the remote starter and Alarm features are disabled To put the system into Valet Mode 1 Hold down the untock and start stop buttons simultaneously for 3 seconds 2 The Parking Lights will flash 3 times The siren will chirp twice and the LED will come on To take the system outof Valet Mode 1 Hold down the untock and start stop buttons simultaneously for 3 seconds 2 The Parking Lights will flash 2 times The siren will chirp twice then pause then chirp twice again and the LED will go our Panic Mode Safety feature Activate Panic Mode in an emergency situation CT 5060 User Guide P 4 In an emergency situation you can activate Panic Mode using the Lock or untock button This will e Shut down the engine e Disarm the Starter Kill and e Unlock the doors if untock is Activate the siren for 1 minute pressed See below for a description of the Starter e Or lock the door if tock is Kill pressed To activate Panic Mode e Press and hold the untock but2. MANUAL TRANSMISSION MULTI CHANNEL RE E STARTER AND FULL FEATURED ALARM S TEM User Guide Introduction sser 1 Remote Door LOCKS sses 6 Basic Remote Operation 1 Passive or Active Arming 7 Remote starting Your Vehicle 5 2 Disarmed Notification scseseeee 7 Remote startng sss 2 Shock Sense And Warn Away Setting the system to Ready Mode 2 SENSE sssessssessastenssenseeennensesenseansnsen 7 Remaining in Ready Mode vss 2 Siren CHIMS sisser 7 Vehicle Presets 3 Open Zone Notification ee 7 Driving Off 3 Ignition Controlled Door Locks 7 Idle MOC cecccccccscsccssestcssecsesseteetecetessees 3 Ignition RE LOCK eee 8 Valet Mode 4 Secure LOCK 8 Ignition Valet 4 Remote Trunk Release sanss 8 Remote Valet 4 Starter K ll lss 8 Panic MOC nnn 4 Engine Run TIME sssri 8 Quick LOCKOUT cccssscecsssseesssssecessees 5 Multi Car Operation 8 Cold Weather Mode cscs 5 Car FIN Er sser 9 Priority Door ACCESS sses 6 Diagnostics Chirps Diagnostics Chirp Delete enserrer 6 Parking Lights scscscsssssssssssesnssernserssscsn 9 User selectable Options sacs 6 Parking Lights Flash Rate Normal Operation 9 Sate S t ten 6 Introduction This Module is a state of the art combination of an Alarm system and a remote car starter It represents a major breakthrough in vehicle security technology and remote starter systems Basic Remote O peration This system is equipped with a 4 button multi channel two way transmitter It can
3. the vehicle e Press the Lock button if you need to lock the doors while the engine is running Caution Do not leave children or pets unattended in a car running in Idle Mode P 3 User Guide CT 5060 Valet Mode The system can be placed in Valet Mode to disable the remote starting capabilities If the vehicle needs to be serviced or if you park it indoors the Valet Mode will prevent the engine from being remote started accidentally To put the system into Valet Mode 1 Turn the key to the icNition on RUN position 2 Within 3 sec press the Valet button and release it The LED will come on The system is in Valet Mode To take the system outof Valet Mode 1 Turn the key to the IcNition on RUN position 2 Within 3 sec press and release the Valet button The LED will go out The system is out of Valet Mode The Valet button can only be used if the ignition key is in the IGNITION on RUN position Ignition Valet The system can be placed in Valet Mode to disable the remote starting capabilities If the vehicle needs to be serviced or if you park it indoors Valet Mode will prevent the engine from being accidentally started by remote control To ENTER Valet Mode 1 With the key in the Ignition switch turn the key to the on RUN IGNITION and then oFF positions 5 times within 10 seconds 2 The Parking Light will flash 3 times indicating the Module is now in Valet Mode The LED will turn on solid
4. this feature is enabled the user must press the start stop button 2 times within 3 seconds to remote start the vehicle If Swap Start Mode has been configured by your installer to remote start your vehicle press Lock and untock simultaneously Press start stop to trigger the aux 2 output Safe Start features will eliminate accidental remote starts e g when there are children playing with the transmitter Remote Door Locks If your system was installed with the Remote Door Locks option you will have the convenience of remote keyless entry To uNLock your doors and pisarm the system 1 Press and hold the untock button for approx 1 sec 2 The parking lights will flash twice and the LED will go out to confirm that the doors have been unlocked that the Starter Kill feature is disarmed if it was installed and that the Alarm is disabled To Lock your doors and arm the system 1 Press and hold the Lock button for approx 1 sec 2 The parking lights will flash once and the LED will flash slowly to confirm that the doors have been locked that the Starter Kill feature is enabled if it was installed and that the Alarm is armed CT 5060 User Guide P 6 Passive or Active Arming By default the system is configured to Passive Arming Mode In Passive Arming Mode the Starter Kill and the Alarm will automatically arm 30 seconds after the last door is closed The system will not arm itself if a door is left open Im
5. Turn the ignition key to the IGNITION on RUN position e Press and hold the start stop button for 3 seconds The parking lights will flash once To check whether Cold Weather Mode is active press and release the brake pedal the parking lights should stay on while your foot is on the brake pedal P 5 User Guide CT 5060 Priority Door Access This safety feature lets you unlock only the driver s door when you press the uNLock button on the transmitter and then untock the rest of the vehicle doors if the unLock button is pressed for a second time within 3 seconds Chirp Delete To temporarily disable the siren s chirp confirmations upon arming and disarming e g in a quiet neighbourhood 1 Press the trunk button 2 Within 3 seconds press the Lock or untock button to arm or disarm without any chirps Note Your installer can program the Chirps Disabled feature if you want the chirps to be permanently disabled User selectable O ptions The system was designed with flexibility and OEM integration in mind With its programmable options this unit can single handedly control nearly any electrical system in your vehicle Note The programming of your system should be left to a professional Changing any one of the settings may affect the operation of your system The user selectable options are as follows Safe Start Safety feature Safe Start features will prevent accidental remote starts If
6. an front and rear as well as heated seats if equipped should not be left on migu It is recommended to leave the settings on Low or mepium instead Windshield Wipers amp Radio amp Headlights Certain vehicles require the radio and or windshield wiper and or headlight circuits to become energized while running under remote start When leaving the vehicle you must ensure that the windshield wiper and headlight switches are orr Leaving the headlight Switch on on certain vehicles could cause them to remain on even after remote starter shut down resulting in a dead battery Driving O ff With the vehicle running under remote control press the untock button to pisarm and untock the doors Enter the vehicle and do the following e Turn the ignition key to the icnmion on RUN position Do not turn the key to the start position while the engine is running This will cause the starter motor to re engage e Press the brakes to disengage the remote starter unit You are now ready to drive off Idle Mode This feature allows you to remove the key from the ignition and leave the vehicle running for its pre programmed run time while you are away from your vehicle This feature is handy if you need to stop for a quick delivery or at a convenience store To enable the Idle Mode 1 Press and hold Lock uNLocK or sTaRT STop on your transmitter while the engine is running 2 The parking lights will come on 3 Remove the key exit
7. cles both equipped with identical systems to control both systems with only one remote transmitter To control the second vehicle simultaneously press the Trunk button and the button of the function you wish to use e Press TRUNK Lock button simultaneously s LOCK e P ESS TRUNK UNLOCK nnen UNLOCK POSS TRUNK START STOP occccccccrennnnsrnii START POSS TRUNK START STOP scccsccssssssessssssestssssesssesvssesseens STOP PSS TRUNK LOCK UNLOCK ccc AUX 3 TRUNK PreSS TRUNK START STOP FOF 3 SOC ccnn COLD WEATHER MODE CT 5060 User Guide P 8 Car Finder When enabled the Car Finder option will help you locate your vehicle by sending a pulsating signal through the horn or the siren To hear the signal press the Lock and unLock buttons simultaneously This will produce a pulsating signal for the time you keep the buttons pressed Diagnostics Chirps Diagnostics Parking Lights Lock and arm the system Lock confirmation Entering Mode 1 in the programming options Start attempt when engine is already running under remote control Unlock and disarm Transmitter learnt Entering Remote Valet Entering Mode 2 in programmi aes oe Lock and arm a zone is unprotected Entering Mode 3 in the programming options Unlock and disarm an intrusion occurred Entering Tach Learning procedure e Siren or Horn Chirp Timing adjustment Constantup e In Siren Mode alarm condition generated by a
8. g the trunk button for 3 sec on the transmitter or by pressing the trunk button twice within 3 sec Starter Kill This added security feature will immobilize your vehicle when the system is armed If your system was installed with the Starter Kill option you will not be able to start your vehicle with the key unless the system has been disarmed first The Starter Kill option follows the Alarm arming function and can therefore be programmed to be active will not arm automatically or passive will arm automatically In passive Mode the Starter Kill can be set to arm automatically in 30 seconds either with or without Siren chirps To disarm the Starter Kill press and hold the untock button on the transmitter The parking lights will flash twice If door locks were installed this will also unlock the doors In passive Mode the system will automatically re arm itself 30 seconds after unlocking the doors if the key has not been inserted in the ignition by then To arm the Starter Kill press and hold the tock button on the transmitter The parking lights will flash once If the door locks were installed this will also lock the doors Engine Run Time If you have a gas engine your system can be programmed to run the engine for 4 15 or 25 minutes 15 min default If you have a diesel engine it can be programmed to run the engine for 9 20 or 30 minutes 20 min default M ulti Car O peration This option allows the owner of two vehi
9. he alarm was triggered in which case there will be 4 chirps when unlocking e Open Zone Notification the system will warn for doors opened up to 10 seconds after arming e No Chirp the vehicle will not chirp under any circumstance O pen Zone Notification This feature will warn the user when a Door is left open upon the arming of the Module a 10 sec notification delay will take place after which the Siren will chirp 3 times if an open door is detected Ignition Controlled Door Locks This is an added security feature If your system was installed with the Ignition Controlled Door Locks option the doors will automatically be locked as soon as the key is turned to the IGNITION ON RUN position while the brakes are pressed When the key us turned to the oFF position the doors will automatically be unlocked P 7 User Guide CT 5060 Ignition Re Lock When the Ignition Controlled Door Locks option is enabled and the ignition is on should any door be unlocked and opened all the doors will be re locked next time the brake pedal is pressed Secure Lock This is an added security feature If your system was installed with the Secure Lock option it will automatically lock your doors and arm the system 4 seconds after your start your car by remote The system will automatically lock the doors again after shut down Remote Trunk Release If your system was installed with the Remote Trunk Release you can open your trunk by pressin
10. n intrusion by Panic to Mode or when the Module is powered up The Siren will sound fo 60 seconds 60 sec Constantup e In Horn Mode alarm condition generated by an intrusion by Panic to Mode or when the Module is powered up The Horn will sound fo 30 seconds 30 sec Parking Lights Flash Rate Normal Operation Flashes Description SC e Doors locked Starter Kill armed e End of Run Time e TRUNK button pressed e Start signal received by the Module Cold Weather Mode cancelled Cannot start after maximum number of attempts is reached Run Time cancelled Remote start attempt cancelled by remote Doors unlocked Starter Kill disarmed Exit Remote Valet Exit ignition valet P 9 User Guide CT 5060 e Entering Cold Weather Mode e Exit Ready Mode e Enter Remote Valet e Enter ignition valet e New Transmitter learnt e Tach learnt e Remote start attempt was made with a Tach or a vacuum signal detected before cranking e Unit reset occurs when the unit is reset to factory defaults e 12 volts detected on the Brake line cranking cancelled e Entering Tach Learning 10 e The Hood Switch line went to ground during cranking or run time ein Valet Mode al Home Valet Mode ONsolid Cold Weather Mode the Brake Pedal is being held down lel step one of the Programming Mode om leo ee e Entering Home Valet Mode ON4sec Lock or untock pulse if door pulse is configured to 4 sec e If the Ho
11. od Pin switch has been pressed twice the Unit went into step 1 of the Programming cycle and no Transmitter activity was detected for 20 seconds e Or the Unit went into step 1 of the Transmitter Code Learning procedure and no activity was detected for a few seconds The Unit has exited the Transmitter Code Learning procedure e If the Module gives irregular flashes 1 to 10 flashes followed by a pause followed by more flashes it is in Playback Mode This occurs when the Hood switch line is flashed 3 times e Panic Mode set off CT 5060 User Guide P
12. operate two independent identically equipped vehicles see Multi Car Operation for second car transmitter functions The functions of the transmitter are as follows DOC 3 55 CA September 9 2004 Manufactured in Canada by Autostart LOCK Locks the Doors and arms the STARTER KILL UNLOCK Unlocks the Doors and disarms the STARTER KILL TRUNK Opens the TRUNK or activates the AUX 3 output START STOP Remote starts or shuts down the Engine Cold Weather Mode ON if the button is pressed for 3 seconds Note Pressing the Lock and UNLOCK buttons at the same time will activate the aux 2 output Remote starting Your Vehicle Remote starting Press the start stop button for approx 1 second The parking lights will come on informing you that the unit has received your signal The engine will start approx 5 seconds later The parking lights will remain on during the pre programmed run time If the vehicle doesn t start at the first attempt the system will shut down wait a few seconds and try to start the engine again It will try to start the engine 3 times before giving up Setting the system to Ready Mode This unit is designed for Manual Transmissions only In order to remote start the vehicle the Unit must first be set to Ready mode Ifthe Unitis not set to Ready Mode it cannot remote start the vehicle Once the system has been set to Ready Mode the vehicle can be remote started and stopped at will as long a
13. portant note When the system re arms automatically or if there is an Alarm condition you can disarm the system by simply pressing the UNLOCK button Disarmed Notification This feature will notify the user when the vehicle was left disarmed after the Engine has been shut down and all doors have been closed after 10 seconds the horn will honk once if the doors have been left unlocked Shock Sense A nd Warn A way Sense This system can react to a full shock by triggering the Alarm it can also respond to a lighter shock 30 of the strength of a full shock by giving a wamavey without triggering an Alarm condition When the Engine is running after a remote start however the system will prevent any Alarm condition to be triggered it will still give a warning sound if warrramayis enabled Siren Chirps The siren will chirp to confirm the system s basic operations e By default when the doors are being locked the siren will give one chirp if none of the zones are active e fa zone is active as the doors are being locked the siren will give three chirps e When the doors are being unlocked the siren will give two chirps if no intrusion was detected e fan intrusion was detected as the doors are being unlocked the siren will give four chirps The system can alternatively be set to e Warning Mode no chirp during lock unlock unless a zone is active when locking in which case there will be 3 chirp upon locking or unless t
14. s the Unit never exits Ready Mode 1 Ensure that all the Doors are closed and that the Gear Lever is in the Neutral position 2 With the Engine already running apply the Parking Brake 3 Within 20 sec press Lock UNLock or start stop on the Transmitter The Parking Lights will flash 3 times quickly and remain lit 4 Remove the key the Engine will go on running 5 Exit the vehicle and close the Door 6 Press either a Lock to lock the Doors arm the Alarm and shut down the Engine b unLock to unlock the Doors and shut down the Engine c START STOP to shut down the Engine without affecting the Doors or d TRUNK to lock all Doors and engage idle mode Remaining in Ready M ode Once the vehicle is in Ready Mode you can start and stop the vehicle at wish However if any one of the following events occurs the vehicle will exit Ready Mode thus eliminating the remote start option until Ready Mode is restored CT 5060 User Guide P 2 Door opened Hood opened Brakes pressed Parking Brake disengaged e Key turned to the IcNiTion on Run position Should any of the above occur Ready Mode will be cancelled Note The unit will notify the user that it has exited Ready Mode by giving three slow flashes of the vehicle s Parking Lights V ehicle Presets Heater amp Heated Seat When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start Settings for the blower motor f
15. ton for approximately 3 seconds until the siren starts to sound and the parking lights flash this will unlock the doors before the siren sounds e Orpress and hold the Lock button for approximately 3 seconds until the siren starts to sound and the parking lights flash this will lock the doors before the siren sounds Panic Mode will automatically shut down after 1 minute Note To stop Panic Mode before the 1 minute delay press the Lock or UNLOCK button until the siren stops Quick Lockout Also called Secure Panic For fast protection the system will Lock all doors when you press the brake pedal while the siren is sounding Quick Lockout is only available when Panichas been activated Cold Weather Mode When the Cold Weather Mode is active the engine starts every 2 hours and runs for 4 minutes or for 9 or 20 minutes with Diesel engines the routine will go on for a period of 24 hours To enter Cold Weather Mode e Press and hold the startistop button for 3 seconds until the parking lights flash 3 times If Safe Start is enabled the start stop button must be pressed beforehand see below To enter Cold Weather Mode if Safe Start has been activated e Press and release the start stop button then press and hold the start stop button for 3 seconds until the parking lights flash 3 times To edtCold Weather Mode do any one of the following e Open the hood e Start the engine using the remote control e
Download Pdf Manuals
Related Search