Autostart CT-1010 User's Manual
Contents
1. Keyless Entry And Alarm System CT 1010 Installation Guide Table of Contents Included in the Kit 1 Dome Light Delay 000 7 Installation Points to Remember 2 Retain Accessory Output 7 Programmable Features 2 Zone 2 Disable Output 7 Harness Description 0c00 3 Multi car Operation 0 0 0 c T How to Flash the Hood Pin 4 Resetting the Module 00 000 0 T Programming a Transmitter 4 Diagnostics Parking Lights Flash Programming Options 4 PRES EEEE E E A 8 Closing Up 8 Included in the Kit Please review the installation guide before beginning the installation especially the wiring diagram and the programming options It is very important that you familiarize yourself with the programming and operation of the system even if you have already installed an alarm system in the past There are many great new features that may be overlooked if the manual is not read you would therefore not maximize the unit s potential Prior to the installation make sure that all the hardware components required to install the system are in the box Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product be that either damage to the vehicle itself or to the Unit This Unit must be installed by a certified technician using all safety devices supplied Only2. registered technicians will be eligible to use the Prostart technical support telephone service Please review the Installation Guide carefully before beginning any work DOC 1 06 November 10 2006 Manufactured in Canada by Autostart Installation Points to Remember O O The following is a list of components included in the kit 1 Control unit 2 CT 200 transmitters 1 plug in L E D 1 Hood pin switch 1 plug in valet button O OOOO o 1 user guide o 1 installation guide The kit also includes the following harnesses o 1 2 pin Wire harness o 1 5 pin Main harness When working on a vehicle always leave a window open Never leave the keys in the car Leave them on a workbench with a window rolled down If possible remove courtesy light fuse to prevent battery drain Inspect vehicle for any body damage or electrical problems Make sure that all the switches and controls operate properly Verify that the vehicle starts and idles properly Never install control unit where it could interfere with normal operation or obstruct service technicians Do not disconnect the battery on vehicles equipped with air bags and anti theft radios Programmable Features The unit was designed with flexibility and OEM integration in mind The system gives installers the output flexibility that every good installer is looking for this unit can be customized and used for almost every possible application With the
3. 3 see programming options This wire will provide a constant 500mA output when the system is armed locked by remote control It can be 12 BLACK Zone 2 Disable connected to an external starter interrupt relay PINK Output armed output This wire should be connected to a single pole double throw relay this wire will connect to pin 85 on the relay and pin 86 will be connected to the ignition wire Installation Guide P 3 3 PIN CONNECTOR 2 WIRE HARNESS Wire Wire colour Description Programmable 500mA negative output 1 10 sec 7 10 sec 4 Unlock output sec or double 1 4 sec pulse ON 250 ms OFF 500 ms ON 250 ms 2 Nowire 12V This pin provides 12V output for INV 200 module BROWN Lock output Programmable 500mA negative output 1 10 sec 7 10 sec or 4 sec pulse 2 PURPLE WIRES These wires serve as a starter kill Cut the factory starter wire from the vehicle in half and connect the two cut wires to the 14 AWG purple wires on the module How to Flash the Hood Pin e Press and hold the hood pin for 4 seconds e Release the hood pin Parking Lights ON e While the parking lights are on press down the hood pin once more ON for 20 seconds and release the hood pin immediately e You now have 20 seconds to select one of the sub menus Programming a Transmitter The transmitter does not come pre programmed and must be programmed after the wiring of the module is completed Th
4. ches its minimum value 10 ms the siren horn will sound 1 long chirp e To save the settings and exit horn chirp duration adjustment press the MLS MLE buttons simultaneously or the press o button on the two way remote The siren horn will sound 3 chirps Then turn the ignition key to the OFF position P 6 Installation Guide Note As a rule you will hear only one short chirp for each adjustment of the horn chirp duration Nevertheless you will hear a long chirp approx 1 second long if either the minimum value 10 ms or maximum value 250 ms is reached Dome Light Delay When the doors are being closed and the vehicle is armed the module will check the dome light to detect whether a door has been left open If the dome light is on the system will generate three chirps to warn the user that a door has been left open There is one chirp if Mode 1 Function 5 Option 2 is selected Retain Accessory Output Retain Accessory output is activated as soon as key is turned to the ON position When the key goes from ON to OFF position the accessory output stays ON and a countdown period of 10 minutes is set The output is turned OFF after 10 minutes or if a door is opened anytime during the countdown period Note The Accessory Output is also turned off while starting the car Zone 2 Disable Output The unit is equipped with a zone 2 disable output that can be used to immobilize the vehicle when the system is arm
5. cting the function press one of the corresponding buttons to select the option for Option 1 fe for Option 5 ka for Option 2 ce 4 for Option 6 la for Option 3 Ld for Option 4 Programming Options MODE 1 INDICATES DEFAULT SETTING FUNCTION 1 Ignition controlled door locks OPTION 1 Ignition lock disabled OPTION 2 Ignition lock enabled OPTION 3 Ignition unlock ONLY OPTION 4 Ignition lock ONLY FUNCTION 2 Door lock pulse timing OPTION 1 7 10 sec lock unlock pulses OPTION 2 4 sec lock unlock pulses OPTION 3 7 10 sec lock pulse and two sec unlock pulses OPTION 4 1 10 sec lock unlock pulses FUNCTION 3 AUX3 Programming Press the ke button for 4 seconds for options 1 through 5 OPTION 1 Constant while button is pressed OPTION 2 Toggle ON Toggle OFF OPTION 3 60 second pulse OPTION 4 1 second pulse with Unlock pulse and Disarm pulse OPTION 5 1 second pulse with Disarm pulse Once the Trunk is closed Arm pulse after 5 sec delay OPTION 6 Disarm function with UNLOCK button FUNCTION 4 AUX2 Programming Use with 4 button for options 1 through 4 and car finder OPTION 1 Constant while button is pressed Car finder disabled OPTION 2 Toggle ON Toggle OFF with 30 seconds timeout or until ignition ON Car finder disabled OPTION 3 30 second pulse Car finder disabled OPTION 4 60 second pulse Car finder disabled OPTION 5 Retain accessory output Car finder enabled OPTION 6 Arm output Car fi
6. e system can retain up to 4 different transmitter codes if a fifth transmitter is programmed the code of the first transmitter in memory will be lost To erase all transmitters from memory perform a module reset Proceed as follows to program a new transmitter 1 Flash the hood pin see above the parking lights will stay on for up to 20 seconds Before the lights go out turn the ignition key to the ON RUN position When the lights are off turn the key to the OFF position Press and hold the SA or i button until the parking lights flash 5 times quickly The transmitter has been stored in memory To exit close the hood oo ih To program a transmitter on the second vehicle for multi car operation you must press the ba button instead of SMA or oi in step 4 of the transmitter programming procedure Programming Options The system is equipped with two custom programming menus that allow the installer to custom fit the outputs of the system according to the requirements of each vehicle Proceed as follows to enter custom programming 1 Flash the hood pin switch see above the parking lights will stay on for up to 20 seconds 2 Before the lights go out press and hold the valet button and then press one of the following buttons Me ener to access mode 1 cH era re ET to access mode 2 3 The parking lights will flash to confirm entry into a mode 4 Release the valet button P 4 Installation Guide After sele
7. ed Zone 2 disable operates in addition to the built in starter kill The unit will give a negative output when the system is armed locked by remote this wire can therefore control an external relay to interrupt the fuel pump or the Ignition The starter kill circuit can be configured to passive mode to arm automatically with a 1 minute timeout Otherwise it can be configured to active mode in which it must be armed by the user Note Installation of a 2 zone disable requires an external relay not included Multi car Operation This allows the user to control two systems with one transmitter Both vehicles must be equipped with identical modules The remote transmitter of the primary vehicle can control the starter kill system the door lock and unlock operations of the second vehicle The remote transmitter of the second vehicle can also operate the primary vehicle To program a transmitter for a second vehicle under multi car operation you must press on he button of the transmitter in step 4 of transmitter programming procedure see page 4 Resetting the Module The system is equipped with a reset function that allows the installer to erase all transmitter codes and return all programming options to their factory defaults To reset the module 1 Flash the hood pin switch see on page 4 the parking lights will stay on for up to 20 seconds 2 Immediately press and release the valet button 5 times 3 The parking lights wi
8. integration of timed latched and ON OFF outputs this unit can single handedly control virtually any electrical system in the car The programmable features are as follows 1 2 3 Ignition Controlled Door Locks o 1 12 pin principal auxiliary harness o 1 3 pin connector cable Always use a grommet when running wires into the engine compartment Never run wires through bare or sharp metal Always solder and tape all connections Never ground the control unit to the steering column of the vehicle When you probe test the wires of a harness make sure you check the plug in connector The wires for the air bags aren t always identified on the harness split loom or a yellow tape However they are always identified on the connector Keep the Transceiver away from other types of antennas GPS Onstar Make sure all security equipment is installed the Valet switch the hood pin and the warning label e OFF by default This feature will LOCK all the Doors of the vehicle while the Ignition Key is in the IGNITION ON RUN position and only when all the doors are closed there is no recurrence of this action The unit will UNLOCK all Doors when the Ignition Key is turned back to the OFF position e f Ignition Lock Only is selected the system will only LOCK all Doors while the Ignition Key is in the IGNITION ON RUN position and only when all the doors are closed there is no recurrence of this action e f option Igniti
9. ll flash 8 times upon reset Note After a reset has been performed the system will set all options back to their default values see the programming page for default values and all transmitters will need to be programmed again Installation Guide P 7 Diagnostics Parking Lights Flash Rate FLASHES DESCRIPTION Guck i Locked by transmitter system armed starter kill alarm _ e Unlocked by transmitter system disarmed starter kill alarm 2 Quick e System has exited valet mode e System has entered valet mode 8 Quick Unit reset Occurs when the unit is reset to factory defaults Closing Up Use tie wraps or screws to properly secure the starter Module and keep the wiring away from any moving parts such as the Parking Brakes or Steering Column Shafts Mount all switches in good and accessible locations where they do not risk getting kicked or hit accidentally Most comebacks are the result of misunderstandings about how a product works or performs Take the time to properly explain all functions and features to the customers before they leave the premises Doing this will save time and money Always make all your connections before plugging in the Module and be sure to test all functions properly before closing up the installation P 8 Installation Guide
10. nder enabled FUNCTION 5 AUX1 Programming OPTION 1 Priority door OPTION 2 Dome light output for 60 seconds OPTION 3 Arm output OPTION 4 Disarm output OPTION 5 Retain accessory output Installation Guide P 5 MODE 2 INDICATES DEFAULT SETTING FUNCTION 1 Re lock OPTION 1 Disabled OPTION 2 Enabled Relock all doors 60 seconds after unlocking and no door nor trunk is opened FUNCTION 2 Siren Horn Chirps Available only on some models OPTION 1 Warning chirp only Lock confirmation if Lock button is pressed more than once 3 chirps if a door is opened and Lock button pressed 4 chirps if Unlock button is pressed and an intrusion occurred OPTION 2 Chirp enabled OPTION 3 Chirp enabled with open zone notification Siren Horn warning 10sec after arming if a door is opened OPTION 4 Chirp disabled Lock confirmation if Lock button is pressed more than once FUNCTION 3 Arming OPTION 1 Active arming OPTION 2 Passive arming 60 seconds rearm OPTION 3 Passive arming 60 seconds rearm No TWO STAGE disarm OPTION 4 Active arming with disarm notification ignition ON to OFF door opened and then closed FUNCTION 4 Ignition monitoring with Siren Horn mode Available only on some models OPTION 1 Siren mode with ignition monitoring disabled OPTION 2 Siren mode with ignition monitoring enabled OPTION 3 Horn mode with ignition monitoring disabled OPTION 4 Horn mode with ignition monitoring enabled FUNCTION 5 Negati
11. on Unlock Only is selected the system will UNLOCK all Doors when the key is turned to the OFF position provided that the Ignition key was in the IGNITION ON RUN position Passive or Active Arming e Passive with a 1 min time out by default The alarm system on this unit can be set to active mode in which it will not arm itself automatically or to passive mode arms itself automatically with a 1 minute timeout Door Lock Pulse Duration e sec lock and 4 sec unlock pulses by default This system can be programmed to give either 3 5 sec lock unlock pulses this is used to control vacuum door lock system for instance on Mercedes or a single sec lock pulse with a double 4 sec unlock pulse this is used for double pulse disarm unlock systems as in the Maxima Pathfinder and Volkswagen P 2 Installation Guide Alarm 050 4 Relock e f you unlock the doors with the remote transmitter but do not open any door or trunk within 60 seconds the doors will automatically relock Harness Description 5 PIN HARNESS This wire must be connected to bare unpainted metal the 1 BLACK GPEHASS SOREN chassis or true body ground It is preferable that you use a INPUT factory ground bolt rather than a self tapping screw Connect to the 12 V power feed of the vehicle at the Ignition 12V POWER INPUT harness The source wire should have 12 V without Ignition key in the cylinder GREY C aie on Connect this wire to the in
12. stalled hood pin switch supplied YELLOW PARKING LIGHT EX BLACK INPUT Connect to ground or 12 V for polarity control on pin 5 PARKING LIGHT Connect to parking lights circuit of the vehicle This wire will OUTPUT give either a positive or a negative output depending on the polarity of pin 4 YELLOW 12 PIN HARNESS Description Connect to the Ignition wire of the vehicle The source wire should have 12 V with the ignition key in the IGNITION ON RUN and CRANK positions IGINITION INPUT 2 PURPLE OO O M GREY Ee Light BLUE TRUNK INPUT Connect to the wire that tests ground with trunk open When connected to the wire that provides ground when remote GREY NEGATIVE started this input will cause the alarm system to ignore the GREEN TRIGGER INPUT ignition and shock sense while running by remote start Trigger alarm input selected by Default WHITE s NA WHITE BLACK INPUT This wire should monitor all the doors e ep C NeuT opened lsualy he domeinen o RED INPUT opened usually the dome light circuit neo ae This wire will provide 500mA ground output depending on the Light BLUE output configuration of Mode 1 Function 5 see programming options AESSR This wire will provide 500mA ground output depending on the BROWN output configuration of Mode 1 Function 4 see programming options This wire will provide 500mA ground output depending on the GREEN output configuration of Mode 1 Function
13. ve trigger OPTION 1 Ignition and shock bypass under remote start OPTION 2 Trigger alarm input Siren Horn Chirp Duration Adjustment Available only on some models The default horn chirp duration is 25 ms In order to adjust the timing for the Siren select MODE 2 FUNCTION 4 OPTION 1 or 2 To adjust the timings for the Horn select MODE 2 FUNCTION 4 OPTION 3 or 4 The siren horn chirp duration can be configured by following these steps 1 Flash the hood pin switch see on page 4 the parking lights will stay on for up to 20 seconds 2 Within 20 sec press and hold the valet button 3 Press the 4 button to enter horn chirp duration adjustment Siren or Horn will chirp 5 times 4 Proceed as follows to change the horn chirp duration a Every time you press the T button the system will increase horn chirp duration by 3 ms When chirp duration reaches its maximum value 250 ms the siren horn will sound 1 long chirp b Every time you press the button the system will increase horn chirp duration by 10 ms When chirp duration reaches its maximum value 250 ms the siren horn will sound 1 long chirp c Every time you press the E button the system will decrease the horn chirp duration by 3 ms When chirp duration reaches its minimum value 10 ms the siren horn will sound 1 long chirp d Every time you press the be button the system will decrease the horn chirp duration by 10 ms When chirp duration rea
Download Pdf Manuals
Related Search