Audiovox XMB10 User's Manual
Contents
1. Visit Our Website At www audiovox com Product Information Photos FAQ s Owner s Manuals 2005 Audiovox Electronics Corporation 150 Marcus Blvd Hauppauge New York 11788 128 7546 16 128 7546 16 of 162. bridges etc No sound from XMB10 speakers Headphones installed Remove headphones 14 128 7546 14 of 16 PaQ AUDIOYOX 12 MONTH LIMITED WARRANTY AUDIOVOX CORPORATION the Company warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in material or workmanship within 12 months from the date of original purchase such defect s will be repaired or replaced with new or reconditioned product at the Company s option without charge for parts and repair labor To obtain repair or replacement within the terms of this Warranty the product is to be delivered with proof of warranty coverage e g dated bill of sale specification of defect s transportation prepaid to an approved warranty station or the Company at the address shown below This Warranty does not extend to the elimination of externally generated static or noise to costs incurred for installation removal or reinstallation of the product damage to speakers accessories or vehicle and home electrical systems malfunction of satellite transmissions repeater signal or receiver unit This Warranty does not apply to any product or part thereof which in the opinion of the Company has suffered or been damaged through alteration improper installation mishandling misuse neglect accident or by removal or defacement of the factory serial number bar code label s THE EXTENT
3. of the Receiver indicating the Xpress is properly seated The receiver should now be attached securely to the mounting plate rear INSTALLING REMOVING Ty THE Xpress RECEIVER PUSH IN AT TOP TO SECURE IN PLACE c Apply power to the XMB10 by pressing the Power ON OFF button the LED indicator lights blue If the Receiver does not turn on at the same time press the Power On Off I button on the Receiver front panel 4 Removing the Receiver From the XMB10 Press the EJECT button on top of the Boom Box the receiver will swing out automatically Gently grasp each side of the Receiver at the top and pull straight up to disengage it from the mounting plate Xpress RECEIVER INSTALLED 128 7546 8 of 16 Interconnect Diagram RECEIVER BOOM BOX DC POWER XMB10 ADAPTER ANTENNA JACK JACK ANT T J DCPOWER I I 1 bl l I HIDE AWAY He eu ANTENNA DC 12V 1 5A CABLE WRAP Coo i l ee 1 TOAC Tf RECEIVER WALL ANTENNA A OUTLET t ou h LEE 5 Installing the Antenna For best reception the supplied antenna should be placed near a window if in the house or if outdoors in an open area and as high as possible some repositioning may be required to achieve optimum results The following guidelines are recommended a In a major city where XM ground repeaters are present you can usually place the antenna away from a window and stil
4. 546 11 of 16 Specifications Nominal Output Power per Channel Total Harmonic Distortion THD Frequency Response Signal to Noise Ratio Speaker Impedance Headphone Output Impedance Headphone Output Level Headphone Connector Type Auxiliary Input Impedance Auxiliary Input Level Auxiliary Connector Type Equalizer Frequency Overall XMB10 Dimensions Overall AC Adapter Dimensions XMB10 Weight 12 5 0 Watts Rms 0 3 at 1 Watt 30Hz to 20kHz gt 65dB Maximum 8 Ohms Nominal 32 Ohms 800 mV Maximum 3 5 mm Stereo Jack 8K Ohms Nominal 2 0 Volts Maximum 3 5 mm Stereo Jack 6dB Nominal at 2 5kHz 19 1 W x 7 5 Dx 8 43 H 485 mmW x 192 mmD x 214 mmH 1 92 D x 3 3 H x 2 2 W 48 7mmD x 84mmH x 56mmW 6 75 Lbs 3 06Kg 128 7546 12 of 16 Maintenance Periodic Inspection The XMB10 Boom Box should be inspected periodically for external damage At least once every 30 days of use perform the following checks 1 2 3 Inspect the Receiver connector for loose bent or broken pins misalignment etc make sure the Xpress Receiver connector is intact and exhibits no apparent damage Check the VOL control for freedom of motion without binding of any kind Make sure the antenna connector at the rear of the unit is free from damage of any kind and that the antenna lead plug mates correctly and securely Make sure the DC 12V connector at the rear of the unit is also free from damage of any kind and that
5. OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 48 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state U S A AUDIOVOX CORPORATION 150 MARCUS BLVD HAUPPAUGE NEW YORK 11788 e 1 800 645 4994 CANADA CALL 1 800 645 4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA 1287351 15 128 7546 15 of 16 GV E For Customer Service
6. Power Adapter ca P N 136 3990 S 1 pe 1 pc 1 pc XMB10 Boom Box P N 144 2484 Installation Wiring Precautions 1 If using the adapter make sure the adapter cable is not connected to an AC wall outlet until all inter connections have been made and verified The adapter power cable should be connected last 2 Incorrect installation may cause damage to the system 3 For antenna positioning refer to the Antenna Aiming procedure outlined in the Xpress XM Satellite Radio Receiver User Guide 128 7454 Setting Up and Installing Your Kit NOTE The XM signal can be received and pro cessed virtually anywhere as long as there are no obvious satellite signal obstructions such as high terrain trees overhangs etc In placing the antenna therefore these factors must be taken into account Boom Box XMB10 Controls The Xpress XM Boom Box XMB10 provides Power ON OFF and VOLUME pushbuttons A power on LED 128 7546 5 of 16 is also located on the front panel When the Xpress Receiver is installed in the boom box the 1 PHONES Jack Accepts a stereo headphone jack to provide private listening capability for the Boom Box 2 AUX Jack Accepts an audio input signal from an external audio device When using the AUX audio input turn the Receiver off to preserve battery power Adjust the volume level of the external audio device to obtain an audio output from t
7. Wi e MaWNAUDI YO Ess X press Satellite Radio R eceiver XMB10 Boom Box User Guide 128 7546 1 of 16 Released 9 15 05 CONTENTS Congratulation S onec tion Deeper bes a bedu Pr does T 3 EGG Regulallofis iie tte eite okeh o Riva fovetur aec e aE 4 Cautions and Warnirigs ere eee terere stein t er re kend ohh denen 4 Contents XMB O iiit eere e nate Fe eee 5 Installation Wiring Precautions 2 ceccccccceeeeeeeeeeeneceeeeeeeeeeeeeeeeeeeeeeeees 5 Setting Up and Installing Your Kit 5 eir detnr 5 Boom Box XMB10 GCODILFOIS s ierat etre deo neto Reo IRA Ame a tes 5 Interconnect DIAagr imi cen etx dee ER HR RR LONE URS 9 Positioning the XM Antenna eorr on eer adn eese 10 Specificato pee 12 Mealnteralio 4o ed dede tutes ane eh i das ea 13 Cleaning the XMB10 Boom Box sssseeeseemmenen 13 Ei ei ois 14 Warranty RTT ERN UE D HP S 15 2 128 7546 2 of 16 Congratulations Thank you for purchasing the Audiovox Xpress XM Satellite Radio Boom Box You are one step closer to experienc ing the latest innovation in XM Satellite Radio XM Satellite Radio will revolutionize your in home or On the Go entertainment XM features over 150 digital channels 100 commercial free music over 30 channels of news sports talk and entertainment over 20 dedicated channels of XM I
8. are bypassed automatically whenever the supplied AC Adapter is plugged into the DC 12V jack on the back panel COVER LATCHES COMPARTMENT BOOM BOX COVER NEGATIVE POSITIVE BATTERY COMPARTMENT COVER REMOVED POSITIVE NEGATIVE 7 Turn the Boom Box upside down to access the battery compartment 2 Push the battery cover latches forward and flip up the battery compartment cover to the open position 3 Insert eight 8 C Cell batteries observing battery polarity as shown then close the cover 2 Cabling Interconnections You can begin to enjoy Xpress XM Satellite Radio as soonas the Receiver and Boom Box Kit installation are complete Set up your Audiovox XMB10 by following theinterconnect diagram 3 Installing the Receiver in the XMB10 Install the receiver as follows IMPORTANT Make sure boom box power is off before installing and removing the Xpress Receiver a Press the EJECT button at the top of the XMB10 the spring loaded mounting plate will tilt forward MOUNTING PLATE DETENT RECEIVER COMPARTMENT EJECT BUTTON MOUNTING he PLATE Xpress CONNECTOR RECEIVER GUIDE PIN CONNECTOR 128 7546 7 of 16 b After making sure the connectors and guide pin hole are properly lined up gently lower the Xpress into the mounting plate and press down on the Xpress to mate the connectors together The raised detent on the mounting plate will enter the notch on the
9. audio is heard move the antenna to different positions on the surface until an audio output is heard This is the desiredantenna position and should be marked b After determining the optimum position turn off XMB10 and Receiver power disconnect the power adapter from the wall outlet receptacle if indoors and disconnect the antenna cable c When indoors plan the routing of the antenna cable to the cradle Make sure you avoid any obstructions that could crimp kink or twist the 11 cable use protective grommets wherever rough openings are encountered If the antenna is mounted outside route the cable from the antenna position to the interior of the home working the cable through the basement under a window sill etc make adjustments and take up slack whenever necessary If outdoors either leave the antenna in place atop the XMB10 or remove the antenna and find a location free from overhead obstructions such as tree branches or the roof of a tent or other temporary shelter Plug the antenna cable into the ANT connector on the back of the Boom Box When not using battery power as the primary power source plug the female end of the DC Adapter cable into the DC 12V receptacle on the rear of the Boom Box Plug the other end of the DC adapter cable into a 110 volt wall receptacle Apply power to the Boom Box and Receiver You are now ready to enjoy XM programming outdoors or within your home 128 7
10. he XMB10 The volume control on theexternal audio device should be set to mid range 3 VOLUME Pushbuttons Increase or decrease the volume of the audio output signal from the XMB10 To increase the volume level press the pushbutton to decrease the volume level press the pushbutton NOTE The Volume buttons on the Remote Control unit included w Receiver Combo will also control the volume output of the Boom Box Power On Status Low Battery LED The LED lights blue when the Power On Off pushbutton is pressed to apply power to the XMB10 When operating on AC current the LED will briefly flash approximately every 10 seconds When operating on DC batteries current the LED will briefly flash approximately every 5 seconds The LED will also indicate the status of the volume pushbuttons when the AUX Jack is in use the LED will flash each time the Volume or button is pressed until the maximum setting is reached in either direction Then the LED will resume power source flashing as before Power On Off Switch When pressed applies powerto the Boom Box the power on LED indicator 4 lights blue 6 EJECT Button Press this button to release the spring loaded XMB10 mounting plate to install and remove the Xpress Receiver from the Boom Box 128 7546 6 of 16 1 Battery Installation Your Boom Box can operate independently of AC power by installing 8 C Cell batteries as follows NOTE The batteries
11. l achieve the desired results b You can also place the antenna outside on the roof structure provided it is clear of any overhead obstructions 6 Antenna Placement Considerations The antenna should be placed on a relatively flat surface whenever possible When outdoors the antenna may be left in its mount atop the Boom Box provided no overhead obstructions are present 128 7546 9 of 16 To mount the antenna a Plug the antenna into the ANT connector on the back of the XMB10 b Leave the antenna in place on the Boom Box or remove the antenna from its mount uncoil the antenna cable and place it at the preferred location inside or outside the home If the Xpress Receiver display indicates NO SIGNAL the antenna needs to be repositioned In addition even if you are receiving the XM signal it is recommended that you optimize the position of your XM Antenna as described in this section enabling you toreceive the strongest possible signal andconsistent mute free reception c Your Xpress Receiver display has two different signal strengthindicators which will help you optimize the antenna s position The first is a basic signal strength indicator visible at the upper right corner of the display screen during normal listening It has from zero to three vertical bars three bars represent the strongest signal The 10 other is a higher resolution signal strength indicator screen showing Terrestrial and Satelli
12. nstant Traffic amp Weather and the deepest play list in the industry with access to over 2 million titles XM Satellite Radio service gives you the power to choose what you want to hear wherever and whenever you want it XM is America s 1 Satellite Radio provider with over 4 million customers Your Audiovox Xpress XM receiver must be used with an accessory kit such as the Audiovox Home Kit Boom Box or Vehicle Kit as required by your specific installation needs These kits are available at retailers where Audiovox main units are sold Required subscription for service sold separately Installation costs and other fees and taxes may apply including a one time activation fee All fees and programming subject to change College sports games subject to availability Subscriptions subject to Customer Agreement included with the XM Welcome Kit and available at www xmradio com Only available in the 48 contiguous United States 2005 XM Satellite Radio Inc XM is a trademark of XM Satellite Radio All rights reserved All other trademarks are the property of their respective owners 128 7546 3 of 16 FCC Regulations This unit complies with the interference limits relative to a Class B digital device applicable under Part 15 of the FCC Rules regarding installation in a residential environment If the unit is not installed in accordance with these instructions it could cause harmful interference to audio or television reception If
13. te indications which allow you to opti mally aim your XM Antenna To access and use this screen refer to the Xpress XM Satellite Radio Receiver User Guide 128 7454 7 Positioning the XM Antenna The antenna supplied with the XMB10 is a high gain type that can receive XM s signal from one of XM s satellites and or depending on where you live XM s terrestrial repeaters It is recommended that the antenna be positioned near a south facing window or outdoors with a clear view of the southeastern sky in order to receive the satellite signal In some cases it will be possible to receive XM s signal through standard home walls or a roof To position your antenna first set up the Boom Box as described earlier in this user guide Next position the antenna until you receive the strongest possible satellite sig nal If the satellite signal is not available you can op timize it for a terrestrial signal where available 128 7546 10 of 16 NOTE Do not cut the antenna cable and attempt to splice it or attach alternative connectors or cable The cable and connectors used in your XMB10 are specially chosen and attached at the factory to ensure that they will work with XM s unique frequency band Use an XM approved antenna extension kit from your local consumer electronics retailer Failure to do so could damage the unit a Apply power to the XMB10 Boom Box as outlined previously in paragraph 3c and obtain an audio output If no
14. the AC Adapter plug mates correctly and securely Check the antenna for any physical damage make sure the antenna lead is secure and not nicked or frayed Inspect the overall Boom Box case and speaker grilles for damage such as nicks scratches punctures etc Cleaning the XMB10 Boom Box When cleaning the Boom Box make sure the AC Adapter is unplugged from the power source Do not use liquid cleaners or aerosol cleaners Use a lint free cloth lightly dampened with water for cleaning the exterior of the Boom Box only 13 128 7546 13 of 16 Troubleshooting FAULT PROBABLE REMEDY CAUSE System does not turn on Receiver power is set to off Turn Receiver power on using the Xpress Power On Off button Batteries not installed or installed incorrectly Install batteries observing correct polarity XMB10 does not operate using As long as the AC power connector is at Remove power connector from rear batteries tached to the rear panel operation is disabled panel of XMB10 Intermittent operation Low battery level Replace batteries batteries ANTENNA error message Satellite antenna not connected to XMB10 ee satellite antenna to XMB10 rear panel rear panel ANT jack Xpress Receiver not firmly seated in cradle Press firmly down on the Receiver to mounting plate ensure that the connector is firmly mated to the Boom Box connector NO SIGNAL message Check for obstacles over or around antenna Change location to eliminate nearby obstacles
15. this condition persists after corrective action consult your dealer or experienced installation facility Cautions and Warnings 1 2 Within the home do not install the Boom Box ina position that obstructs viewing of any home entertainment component such as Television or stereo system indicators and displays Do not install or use the XMB10 in locations exposed to direct sunlight or in areas subject to extreme temperatures do not operate the unit in moist areas in rain or in areas adjacent to water such as pools hot tubs etc When outdoors position the XMB10 and antenna where there are no obvious satellite signal obstructions such as high terrain trees overhangs etc When installed indoors unplug the AC Power Adapter from the wall outlet when the XMB10 is not to be used for an extended period of time If batteries are installed set the Power On Off VOL control to the Off position to prevent unintentional battery discharge or remove the batteries To avoid possible damage to the Receiver Boom Box caused by battery leakage it is recommended that the batteries be removed when the Boom Box is not being used for an extended period of time Do not install or place the XMB10 on an inclined or unstable surface By adhering to these warnings and safety considerations serious accidents and or personal injury can be avoided 128 7546 4 of 16 Contents XMB10 Antenna P N 118 1155 Users Guide P N 128 7546 AC DC
Download Pdf Manuals
Related Search