Audiovox VM9216BT Installation Manual
Contents
1. Installation Guide What s in the Box VM9216BT Head Unit Single DIN Sleeve External Microphone Trim Ring Power Speaker Harness Owner s Manual NAV104 Microphone Harness Installation Guide Hardware Bag Tools and Supplies You will need these tools and supplies to install your VM9216BT Torx type flat head and Philips screwdrivers Wire cutters and strippers Tools to remove existing radio screwdriver socket wrench set or other tools Electrical tape Crimping tool Volt meter test light Crimp connections e 18 gauge wire for power connections e 16 18 gauge speaker wire VM9216BT Disconnecting the Battery To prevent a short circuit be sure to turn off the ignition and remove the negative battery cable prior to installation NOTE If the VM9216BT is to be installed in a car equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be lost Under these conditions use extra caution during installation to avoid causing a short circuit Pre installation 1 Remove the four screws that attach the mounting sleeve to the radio and remove the sleeve 2 Install the2. TH REVERSE E Gearbox amp E Switch WSS roun Ignition Switch ACC RED T amc i e__ ACC oe BATTERY YELLOW e om aa FUSE 15A Battery L l BLACK C Q BATTERY Ground w SAM pus SiriusXM Antenna Jack Ca Connector lt lt A Antenna Antenna control Connect this lead to a motorized antenna turn on lead BLUE Maximum current draw 300mA i HOC ANT CONT BLUE WHITE External power amplifier control gt e PCONT Car Phone BROWN Mute leave open if not connected MUTE S o o ae FRONTL a WHITE BLACK FRonTL T E FRONT L xe L GREY C GREY BLACK A FRONT RH FRONT R a w FRONT R es PURPLE GREEN BLACK REAR R a REAR R ees REAR L i REAR L 128 9183
3. For basic iPod connectivity you can use the white 30 pin to USB iPod cable that came with your Apple device For iPod video or photo playback you must purchase the jLink USB cable Connect the iPod cable to the rear chassis iPod inputs USB 3 5mm connectors and route the iPod cable to an accessible part of the dash area for easy connectivity For occasional iPod use keep an iPod cable in your glove box and use it to connect the iPod to the front USB connector Speen CAMERA YELLOW VIDEO OUT REAR R REARL FRONTR FRONT L SUBWOOFER YELLOW Rear View Video Camera Rear Video J i fe Is Need Help For technical assistance call the Jensen customer support line at 1 800 323 4815 eT PARKING BRAKE PRK SW PINK External Power Amplifier Co O Z iss f Steering Wheel Control SWC Requires PAC SWI PS Interface Adapter Sold Separately lms 4 MICROPHONE NAV BUS i External Microphone NAV104 Connector D optional equipment GREEN WHITE
4. mounting sleeve a Install mounting sleeve into the dashboard or optional adapter Do not force the sleeve into the opening or cause it to bend or bow b Locate the series of bend tabs along the top bottom and sides of the mounting sleeve With the sleeve fully inserted into the dashboard opening bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard c Install the support strap to make the unit more stable 3 Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve CAUTION Be careful not to damage the car wiring VM9216BT Wiring WARNING Only connect the unit to a 12 volt power supply with proper grounding Complete wiring as illustrated in the wiring diagram on page 4 Once the wiring is complete reconnect the battery negative terminal If there is no ACC available connect the ACC lead to the power supply with a switch NOTE When replacing a fuse be sure to use correct type and amperage to avoid damaging the radio The VM9216BT uses one 15 amp fuse located in the black filter box in line with the main wire harness Final Installation After completing the wiring connections turn the unit on to confirm operation ignition switch must be on If unit does not operate recheck all wiring until the problem is corrected Once proper operation is achieved turn off the ignition switch and proceed with final mounting of the chass
5. is 1 Connect the wiring adapter to the existing wiring harness 2 Connect the antenna lead 3 Carefully slide the radio into the mounting sleeve making sure it is right side up and secure with the original four screws 4 Attach one end of the perforated support strap Supplied to the screw stud which is screwed into the threaded insert on the back of the unit using the hex nut provided Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided Bend the strap to position it as necessary 5 Replace any items you removed from the dashboard CAUTION The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration NOTE For proper operation of the CD DVD player the chassis must be mounted within 20 ISO DIN Installation of horizontal Make sure the unit is mounted within this limitation 1 Remove the mounting sleeve brackets 2 Remove the trim ring 3 Mount the factory brackets on the new radio using the existing screws from the old radio 4 Slide the radio chassis into the dash opening and secure 5 Re install the dash panel Wiring Diagram IMPORTANT Incorrect wiring connections can damage the unit Follow the wiring instructions carefully or have the installation handled by an experienced technician VM9216BT
Download Pdf Manuals
Related Search