Audiovox PSB110 Owner's Manual
Contents
1. lt ie G Bo z Ke Q O fae 10 C per O Ranges shown are estimates and can be effected by weather or Solid Beep Fast Beep Slow Beep Your system may alert to some situations and accuracy can be effected by the examples of situations below Always use mirrors and caution when backing Always completely test the system after installation or modification Sensors that are dirty covered with snow ice heavy rain or other objects can cause false alerts or reduce sensitivity Do not cover sensors with paint protection film stickers vehicle wrap or any other material as this will block the sensor If the automatic self test alerts you to a problem STOP Park Look Seek service on the sensor system before using for parking Sensor installation Sensor maintenance DO NOT directly spray the sensors with high pressure car wash wands Normal drive through car washes are OK Washing your car with low pressure water and a soft sponge or cloth is always the best way to insure a clean sensor surface and best operation If your sensors are covered by snow and ice use warm water to melt away the ice Do not use a scraper over the sensor surface this could damage the sensor and effect it s operation Sand mud and road debris should also be washed away with warm water soap and a soft cleaning cloth to insure the sensor surface is not damaged Each sensor has UP and2. use of a relay not included in order to use the white backup light as a trigger Low current systems may not be able to supply enough power to operate additional equipment and could Cause poor erratic or operational issues as well as possibly setting a code or check vehicle light Red P Reversing light Buzzer PSB110 Remark 1 spare sensor connector A D is for upgrading to 4 sensor system 2 2 sensor system don t pull out plug A D Troubleshooting e After Installation the buzzer or display does not operate A Check all wire connections B Make sure the vehicle ignition is on C Is the vehicle in Reverse White reverse lamp is on D Is there enough current in the lamp circuit to operate the sensors LED and low current lighting systems may require additional power and a relay e The system shows a damaged or non working sensor A Make sure all sensor connections are secure at the module B Check to make sure all waterproof connectors at the sensors lead are correctly connected and secure C Make sure the sensor is not covered or blocked D Make sure that the sensor has not been damaged e The system instantly gives a solid or false warning A Are all sensors connected correctly B Is the power source ground correct and sufficient to operate the system C Are the sensors in correctly with UP in the correct position f these problems persist A For consu
3. Specifications e Input voltage 9 16V DC e Beep SPL 70 90 dB e Display range 0 3 m 2 5m 1 ft 8 2 ft e Buzzer range 0 3m 1 5m 1ft 4 9ft e Sensor installation height 45 cm 65 cm Sensor Mounting Hole Size 18 8mm Buzzer or LED display Buzzer LED indicator Distance Display l M a 3 7 e fF eae PAPINE ASSIS VS SIN Manual PSB110 PSB120 VOXX Electronics Corporation Hauppauge NY 11788 Technical Assistance 1 800 323 4815 All rights reserved 2014 VOXX Printed in China Specifications subject to change without notice REV2 6 2014 Self test function PSB110 With Buzzer When Reverse gear is selected the system will automatically test each sensor each time 1 If all sensors are working normally you will hear one beep 2 If one or all sensors are damaged or defective you will hear 3 beeps 3 If the system is non functional you will not hear a confirmation beep 1 All sensors are working normally Beep once 2 Damaged sensor is detected O00000 oo0000 Important notice 1 This product utilizes high voltage Any unauthorized modifications or damage to the product may result in electrical shock Handle all components with care Inspect regularly for damage to components and cabling 2 You are responsible for ensuring that the installation of this product does not void or affect the vehicle manufacturer s warranty VOXX Electronics Corporat
4. an arrow on the rear of the sensor It is important that the sensors are installed correctly and positioned with the up arrow pointing straight up Sensors installed incorrectly may false have reduced sensitivity or not work at all The sensors included in this kit are designed to be used in plastic bumper installations ONLY with the drill it included in the kit To install in metal bumpers use Advent Drill bit part PSBMDRB Not included in this kit BEFORE DRILLING MEASURE MARK AND CHECK BEHIND THE BUMPER TO INSURE YOU DO NOT HIT ANY METAL SENSOR SUPPORT OR ANY OTHER OBSTRUCTIONS The sensor must be mounted vertical and straight for proper operation Measure the bumper for proper placement see above Mark location with a grease pencil Check behind location to insure your OK to drill here If OK use the supplied hole saw to drill your mounting hole Use caution to not slip and scratch the bumper TIP Use tape around the hole to protect the paint lt Rear bumper Guide the sensor wire through the hole Insure the sensor is inserted with the arrow UP Push firmly into the hole Connect the extension leads to the sensors and note A B C D for later connection Route all wires from the sensors to the control module located in the rear of the vehicle interior Make sure all wires are securely attached to the vehicle using wire ties and your opening into the vehicle does not have sharp edges that could damage t
5. he wires Sensor wires CAN NOT be extended Seal the hole entering the vehicle with a grommet or silicone Follow the included wiring instructions to complete your installation Installation diagram Sensors MUST be installed and plugged in as shown for correct zones D c Buzzer B A Display 1 5ft lt H lt 2 1ft 45cm lt H lt 65cm Space sensors as shown above Even spacing will result in the best operation After installation is complete you should test the system With the vehicle on a flat surface with no obstructions not inside the shop ignition OFF and parking brake engaged Turn the ignition on and have someone inside the vehicle place their foot on the brake and shift the vehicle to Reverse Stand to the side of the vehicle and place your hand over each sensor one at a time You will hear a beep or see the display confirming operation of each sensor Once done place the vehicle in PARK Next using a traffic cone or board 1 x 3 placed 9 feet or more behind the vehicle do not stand behind the vehicle slowly backup to the object The sensor should give you a series of beeps increasing in speed until you reach the safety zone The buzzer will give a solid tone STOP The system is working correctly if all of these tests are successful NEVER STAND BEHIND A MOVING VEHICLE TO TEST SENSORS OR HOLD THE TEST OBJECT NOTE Vehicles with LED type reverse lamps and or low current lighting circuits may require the
6. ion or its subsidiaries are not liable in full or in part for improper installation resulting in loss or damage to property or for voiding all or part of the vehicle manufacturer s warranty 3 Do not apply excessive force to any of the components contained within this kit Excessive force used before during or after installation that results in a damaged or non functional part will void all warranties 4 Please follow the procedures in this installation manual Improper installation or modification of this product will void all warranties This product is intended to assist in safe driving by signaling the driver of the distance to obstacles in close proximity to the vehicle while the vehicle is in reverse moving slowly You as the driver are solely responsible for the safe operation of your vehicle and the safety of your passengers according to your local traffic regulations Do not use any features of this system to the extent it distracts you from safe driving Your first priority while driving should always be the safe operation of your vehicle VOXX International Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructions PSB120 With Display When Reverse gear is selected the system will automatically test each sensor each time If all sensors are working normally you will hear one beep If the system is non functional you will no
7. mers Please contact the installing dealer or car dealer B Dealer Installer 1 Replace the ECU and check the system 2 Repeat the system testing instructions to identify the issue 3 Replace any non functioning sensor Contact VOXX Tech support at 800 323 4815 for further help
8. t hear a confirmation beep If one or all sensors are damaged or defective you will hear and see Beeps three times e The number and locations of damaged sensors are shown on the display 1 All sensors are working normally Beep once C 2 Damaged sensor is detected Number of damaged sensors B C Damaged sensor locations About the product This Rear Parking Sensor System is designed to assist the driver by providing an alert when an object is behind the vehicle whenever the vehicle is shifted into reverse Never rely solely on this product to ensure the area is clear of children and or obstructions This product is not intended to replace existing safety procedures but rather to add an additional safety tool for your vehicle Your backup sensing system transmits and receives ultrasonic waves from the sensors mounted in your vehicle s rear bumper As the transmitted waves bounce off obstacles behind your vehicle and are received back by the sensors the unit s control box converts these waves into warning sounds or beeps which alerts you the driver of obstacles behind your vehicle Key features e 4 sensor system with audible buzzer or LED display e Anti false alert technology e Self test function e All weather design How does the system work Distance Safe 0 6 0 9m 2 0 3 0ft 0 9 1 5m 3 0 5 0ft G O O i 2 gt 49 3
Download Pdf Manuals
Related Search