Audiovox MM56A User's Manual
Contents
1. Using your fingers tear the foam out of the headrest leav ing a recess where the shell will be inserted NOTE Atthis point you will need to install the harness up through the area into the recess It may be help ful to follow one of the posts and tie wrap it to the post for restraint 128 6544 6 of 12 10 Lay the flaps of the headrest ma terial down into the recess and in sert the Mounting Tray into the re cess Check for fit If it does not fit properly you may need to re move some more foam NOTE The Mounting Tray will need to be secured to the headrest either by using tie straps screws etc 11 Guide the cable through the side 12 13 14 e e e opening of the Mounting Tray and plug it into the Monitor Make sure the connector locks into place In sert the Monitor into the Mount ing Tray and secure the cable using tie wraps or screws Turn the Monitor around and in sert it into the Mounting Tray housing Snap into place Connect the Monitor power input plug to a DC power source Red plug 12 VDC Yellow plug 12 VDC Constant and Black plug to ground Connect the external video source output signal from VCP DVD TV Etc to the VIDEO IN jack Test the system to verify proper installation 7 128 6544 7 of 12 C Controls Indicators Connectors Front View 1 AUX Input Jack 2 Earphone Jack 3 Color Adjust Up Down Buttons 4 Brightness Adjust Up D2. CD 960 W x 234 H Lines 114 2 W x 83 5 H mm CCFL NTSC PAL auto switch Composite video signal 1Vp p 75ohm 10 000 Hours 10 K Ohms 0 3 W Maximum 16 Ohms 32 Ohms 15 kHz 1 Vp p 12 VDC 15 Ripple 0 5 Vp p Max 8 Watts Max 300 Nit Typical 30 Degrees 10 Degrees 45 Degrees 32 F 140 F 0 C 60 C 4 F 140 F 20 C 60 C 85 RH Max 85 RH Max 156 0W x 126 0H x 34 5D mm 500 Grams 16 0 Ounces 12 128 6544 12 of 12
3. MOVIES 2 G0 Color TFT LCD Monitor MM56A Owner s Manual 128 6544 1 of 12 Released 02 11 04 poc EXPLANATION OF GRAPHIC SYMBOLS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSON NEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are A A The exclamation point within a triangle is intended to alert the user that important operating and servicing instructions WARNING TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD DO NOT OPEN Ay CAUTION This product is designed to operate with a 12 volt negative ground battery system Disconnect the ground wire from the battery terminal before connect ing the electrical system Refer to the electrical connection diagram to avoid wrong connection of the electrical system Always use authorized service center for service assistance Do not operate the monitor at temperatures below 32 F 0 C or above 104 F 40 C Keep the monitor clean and dry Never attempt your own repairs This unit should be installed and re paired by qualified technicians or service personnel Do not drop the monitor or expose to strong impacts Do not expose to direct sunlight for extended periods of time Use proper insulation material to prevent short circuiting of the supply system 2 128 6544 2 of 12 IM
4. PORTANT An LCD panel and or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information system control rear or side observation or naviga tion If the LCD panel or video monitor is used for television reception video or DVD play the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in park or when the vehicle s parking brake is applied An LCD panel or video monitor used for television reception video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver s seat where it will not be visible directly or indirectly to the operator of the motor vehicle A Precaution 1 Before installation verify that it will not damage electrical wires fuel lines brake lines hoses exhaust system components or any other items that will impair the operation of the vehicle 2 Ensure the cable has already been pulled through the supporting pipe before installing the base into the headrest Ensure there is no foreign material trapped inside the enclosure before installing the monitor into the base 3 Tighten all screws bolts nuts securely for installation 4 To avoid electrical hazards do not disassemble the cabinet of the monitor 5 Use only the supplied DIN cable Disconnect the cable from the signal source before di
5. own Buttons 5 Power On Off Button 6 Volume Increase Decrease Thumbwheel Control 128 6544 8 of 12 Exploded View HEADREST TRIM HEADREST Vi SHROUD N COLOR MONITOR 6 DIN Connectors 7 Signal Cable 8 Black Wire Ground 9 Red Wire 12 Vdc Input 10 White RCA Jack Audio Input L 11 Red RCA Jack Audio Input R 12 Yellow RCA Jack Video Input 128 6544 9 of 12 D Operation 1 Connect the red monitor power input wire 9 to a DC power source Red 12 VDC and the Black wire 8 to ground 2 Connect the external video source output signal from VCP DVD TV etc to the VIDEO IN jack 12 3 Press power button 4 to turn the monitor on and off The backlight for the button will intensify 4 Adjust the volume increase decrease thumbwheel 5 to adjust the volume level 5 Press the Color 2 and Brightness 3 buttons to adjust the respec tive picture display characteristics 10 128 6544 10 of 12 THIS PAGE LEFT BLANK INTENTIONALLY 11 128 6544 11 of 12 E Specifications Display Resolution Active Area Backlight Input Signal Lamp Life Audio Specifications Input Impedance Audio Output Earphone Bandwidth Input Level Power Source Power Consumption Brightness Viewing Angle Top Bottom Left Right Operating Temperature Storage Temperature Operating Humidity Storage Humidity Overall Dimensions Weight 2004 AEC Hauppauge NY 5 6 Color TFT L
6. sconnecting it from the monitor after turning off the whole system 6 Do not use gasoline thinners or other thinning liquids to clean the unit Remove dust and stains with a damp cloth 3 128 6544 3 of 12 B Installation Front View Top View ui it t Monitor Key 1 Installation will vary from vehicle to vehicle as headrests in vehicles are not standard 2 This unit is intended for installation by professional installers 3 The kit consists of the screen assembly a clam shell housing a trim ring 1 key to remove the screen from the housing and a wiring harness 128 6544 4 of 12 Headrest Mounting Remove the headrest from the vehicle for easi est installation Lay headrest on a flat sur face Center trim collar on head rest as shown NOTE Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down 4 Using a Permanent Marker 5 mark headrest material along the interior of the Trim Ring Remove the Trim Ring and mark an X from cor ner to corner as shown Mounting Tray Monitor Ring Headrest 128 6544 5 of 12 6 Using the utility knife cut the headrest material along the X lines Do not cut the mate rial along the other lines at this time 7 This will leave you with an X cut as shown 8 Pull the flaps up and cut the foam beneath the material to the proper depth Cut all four sides of the foam 9
Download Pdf Manuals
Related Search