Audiovox LCM50 User's Manual
Contents
1. 128 6549 7 of 12 C Controls Indicators Connectors Front View 1 2 3 4 5 6 8 AUDIOWOX COLOR monitor POWER SOURCE IR PICTURE VOLUME AV3 IN FPE Headphone Jack Power Button Source Button IR Sensor Picture Select Button Volume Down Button 7 Volume Up Button AV3 In Jack x 6 7 8 128 6549 8 of 12 Rear View DIN Jack 10 11 12 13 14 15 16 17 18 DC 12V Input Red 12V DC Black Ground Audio Input L 2 Audio Input R 2 Video Input 2 Audio Input L 1 Audio Input R 1 Video Input 1 IR Repeater Connector IR Repeater Transmitter 128 6549 9 of 12 Note This cable 18 is used to connect to a Video Cassette Player or DVD player that doesn t accept the IR Repeater 1 8 3 5mm style plug 17 The IR Repeater Transmitter is provided with an adhesive that allows it to adhere to the remote sensor of the Video Cassette Player or DVD player Remove the backing covering the adhesive and place the IR Repeater Transmitter directly over the Video remote sensor of Cassette Player or DVD player D Operation 1 Connect the monitor power input plug 10 to a DC power source Red plug 12 VDC Black plug to ground 2 Connect the external video source output signal from VCP DVD TV etc to the VIDEO IN jack 13 or 16 3 Press power button 2 to turn the monitor on and off The backlight for the2. AUDIOVOX CORPORATION LCM50 Headrest 5 0 LCD Monitor AUDIOWOX 5 LCD COLOR MONITOR POWER SOURCE IR PICTURE VOLUME A IN O 00 6 Owner s Manual 128 6549 1 of 12 Released 12 5 02 EXPLANATION OF GRAPHIC SYMBOLS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are A The exclamation point within a triangle is intended to alert the user that important operating and servicing instructions WARNING TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD DO NOT OPEN CAUTION This product is designed to operate with a 12 volt negative ground battery system Disconnect the ground wire from the battery terminal before connect ing the electrical system Refer to the electrical connection diagram to avoid wrong connection of the electrical system Always use authorized service center for service assistance Do not operate the monitor at temperatures below 32 F 0 C or above 104 F 40 C Keep the monitor clean and dry Never attempt your own repairs This unit should be installed and re paired by qualified technicians or service personnel Do not drop the monitor or expose to strong impacts Do
3. button will turn brighter 4 Press the volume up 5 or down 6 button to adjust the volume level 5 Press the picture button 4 to adjust the picture display characteris tics The adjustments will be shown on the On Screen Display in the following sequence Color Brightness Contrast and TINT While in the picture select mode video adjustment press the up button 5 to increase the selected adjustment level or press the down button 6 to decrease the level 10 128 6549 10 of 12 THIS PAGE LEFT BLANK INTENTIONALLY 11 128 6549 11 of 12 E Specification 1 Type 2 Power Source 3 Power Consumption 4 Connection Terminals 5 Operating Temperature 6 Storage Temperature 7 Dimensions 8 Video Format Color Liquid Crystal Display LCD Monitor 12 VDC 0 5W 2 x RCA AV Inputs DC 12V Input IR Input 32 F 104 F 0 C 40 C 4 F 176 F 20 C 80 C 140 0W x 111 0H x 33D mm 5 5 W x 4 4 H x 1 3 D NTSC 9 Resolution 600 Pixels Horizontal x 234 Pixels Vertical 2002 Audiovox Electronics Corp Hauppauge NY 128 6549 12 128 6549 120f 12
4. this time 7 This will leave you with an X cut as shown 8 Pull the flaps up and cut the foam beneath the material to the proper depth Cut all four sides of the foam 9 Using your fingers tear the foam out of the headrest leav ing a recess where the shell will be inserted NOTE Atthis point you will need to install the harness up through the area into the recess It may be help ful to follow one of the posts and tie wrap it to the post for restraint 128 6549 6 of 12 10 Lay the flaps of the headrest ma terial down into the recess and in sert the Mounting Tray into the re cess Check for fit If it does not fit properly you may need to re move some more foam NOTE The Mounting Tray will need to be secured to the headrest either by using tie straps screws etc 11 12 13 14 Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor Make sure the connector locks into place In sert the Monitor into the Mount ing Tray and secure the cable using tie wraps or screws Turn the Monitor around and in sert it into the Mounting Tray housing Snap into place Connect the Monitor power input plug to a DC power source Red plug 12 VDC Yellow plug 12 VDC Constant and Black plug to ground Connect the external video source output signal from VCP DVD TV Etc to the VIDEO IN jack Test the system to verify proper installation 7
5. not expose to direct sunlight for extended periods of time Use proper insulation material to prevent short circuiting of the supply system 2 128 6549 2 of 12 IMPORTANT An LCD panel and or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information system control rear or side observation or naviga tion If the LCD panel or video monitor is used for television reception video or DVD play the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in park or when the vehicle s parking brake is applied An LCD panel or video monitor used for television reception video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver s seat where it will not be visible directly or indirectly to the operator of the motor vehicle A Precaution 1 Before installation verify that it will not damage electrical wires fuel lines brake lines hoses exhaust system components or any other items that will impair the operation of the vehicle 2 Ensure the cable has already been pulled through the supporting pipe before installing the base into the headrest Ensure there is no foreign material trapped inside the enclosure before installing the monitor into the base Tighten all screws bolts nuts securely for installati
6. on To avoid electrical hazards do not disassemble the cabinet of the monitor 5 Use only the supplied DIN cable Disconnect the cable from the signal source before disconnecting it from the monitor after turning off the whole system 6 Do not use gasoline thinners or other thinning liquids to clean the unit Remove dust and stains with a damp cloth 3 128 6549 3 of 12 B Installation Front View Top View Clametell 1 Installation will vary from vehicle to vehicle as headrests in vehicles are not standard 2 This unit is intended for installation by professional installers 3 The kit consists of the screen assembly a clam shell housing a trim ring 1 key to remove the screen from the housing and a wiring harness 128 6549 4 of 12 Headrest Mounting 1 Remove the headrest from the vehicle for easi est installation 2 Lay headrest on a flat sur face 3 Center trim collar on head rest as shown NOTE Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down 4 Using a Permanent Marker mark headrest material along the interior of the Trim Ring 5 Remove the Trim Ring and mark an X from cor ner to corner as shown Mounting Tray Trim Monitor Ring 1 1 1 Headrest gt 128 6549 5 of 12 6 Using the utility knife cut the headrest material along the X lines Do not cut the mate rial along the other lines at
Download Pdf Manuals
Related Search