Audiovox APS997E Owner's Manual
Contents
1. Model APS 997E Owners Guide 2 Way LCD Long Range Vehicle Security amp Remote Start System Table Of Contents Features and Options Page 2 4 Arming Your System Page 4 Protection While The System Is Armed Page 5 Disarming The System Page 5 6 Intrusion Signals and Tones Page 7 Valet Override Programming amp Safety Control Switch Page 7 Programming Custom Code Override Page 8 9 Eliminating the Normal amp Disarm Chirps Page 9 Remote Panic Operation Page 10 Remote Control Shock Sensor Selection Page 10 11 Push Button LED Receiver Safety Control Switch Page 11 Remote Starting Your Vehicle Page 11 12 Automatic Start Timer Operation Page 12 13 Optional Device Channels Page 13 15 Turbo Timer Mode Page 15 Telematic Upgrade Page 15 Two Way Remote Transceiver Screen Icons amp Indications Page 15 21 24 Hour Timed Start Setup Operation and Use Page 21 Temperature Start Mode Operation Page 21 Two Way Remote Function Program Chart Page 22 Functions At A Glance Page 23 Replacement or Additional Transmitters Programming Page 24 PATENTED www voxxintl com company patents Page 1 128 9309 1 of 24 5 Button Remote Start Security System With Plug In Shock Sensor amp Starter Disable IMPORTANT In order to provide you with the highest level of security to your vehi cle this system is equipped with selectable manual override circuitry It is possible that you will need to overri2. Any mild impact to the vehicle s glass will cause the alarm to sound a short series of warning tones Any strong impact to the vehicle s glass will cause the alarm to trigger for the full 30 second alarm cycle NOTE If the optional interior illumination circuit was installed the interior light will flash as well for the full 30 second alarm cycle DISARMING THE SYSTEM NOTE If the optional 2 step door unlock circuit is installed when the unlock Page 5 128 9309 5 of 24 transmitter button is activated the drivers door only will unlock pressing the unlock button a second time will cause all doors to unlock NOTE If your transmitter has been configured with single button Lock Unlock to activate the all door unlock feature press the Lock Unlock button a second time within 3 seconds of the first unlock command 1 As you approach the vehicle press and release the Unlock Disarm button on the keychain transmitter The dash mounted LED turns off The LED will start flashing rapidly indicating that the system is re arming automatically Open any door to suspend the automatic arming Parking Lights flash two times Ifthe parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify which zone was triggered Siren sounds two chirps If the siren sounds 4 chirps then the alarm was triggered in your absence Before turning the key on examine the L
3. OPTION 7X 0 00 MELODY ILLUMINATES DISPLAY BACKLIGHT DISPLAY FOR 10 SECONDS 1X 9 9 9 9 9 9 0 9 0 eb VIBRATE TONE SELECT 1X VIBRATES 4 TIMES OR BEEPS 1X ALARM CLOCK MODE 1 ON OFF MELODY SELECT ON OFF FAHRENHEIT CELSIUS 1 MELODY SELECT OPTION 1x F orC POWER SAVE MODE OR 1X MELODY PRIMARY OR SECONDARY TRUNK KEY LOCK BUTTON VEHICLE ON OFF 5 SECONDS MELODY Page 22 128 9309 of 22 of 24 APS 997 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING PASSIVE ARMING ACTIVE REARMING SLOW FLASHING OFF ON SOLID 3 FLASH PAUSE 2 FLASH PAUSE 1 FLASH PAUSE ARMED DISARMED VALET MODE INTRUSION ZONE 3 INTRUSION ZONE 2 INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP 2 CHIRPS 3 CHIRPS ARM DOOR OPENED 4 CHIRPS DISARM INTRUSION These chirps are optional and can be de activated ARM DISARM PARKING LAMP INDICATORS 1 FLASH 2 FLASHES 3 FLASHES ARM DISARM DISARM INTRUSION his device complies with Part 15 of the FCC rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions This device may not cause harmiul interference and 2 This device must accept any interference received including any interference that may cause undesired operation arning Changes or modifications not expressly approved by the party responsible for compliance could void the user s author
4. Enter the vehicle and turn the ignition key to the on position 2 Press and hold the Push Button switch until the LED turns on solid The system will remain in the valet mode 3 Toreturn to normal operation press and release the Push Button switch any time the ignition is on NOTE Always remember to return the vehicle to the valet off position This will ensure that the vehicle remains protected at all times MANUALLY OVERRIDING YOUR SYSTEM USING THE RECEIVERS PUSH BUTTON OVERRIDE SWITCH Your Security System can be disarmed without the use of the keychain transmit ter This is necessary since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails If your system has been selected for Valet Switch manual override as indicated on the last page of this manual to bypass the alarm system 1 Open the vehicle door The alarm will sound 2 Turn the ignition key to the ON position 3 Within 5 seconds press and release the push button override switch The alarm system will stop sounding and enter the bypassed mode You can now start and operate the vehicle normally Typically this override mode is used only if the transmitter has become inoperative Page 7 128 9309 7 of 24 PROGRAMMING YOUR TOM OVERRIDE CODE Unlike override switches easily found and defeated this security system allows the consumer to program a personal override code offering a higher level of security To take
5. Duration 1 Second 3 5 Seconds 1 Sec L Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter Or Selectable Through Software Dome Delay Learn Circuitry Two Vehicle Operation Remote Trunk Release must have electric trunk release Remote Keyless Entry must have power door locks Multiple Vehicle Capable Remote Power Window Roll Up WARNING Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged YOUR SPREAD SPRECTUM TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system Some of today s sophisticated auto thieves use a device known as a code grabber which will receive and store the signal from your key chain transmitter and re transmit at a later time to disarm your system Your Spread Spectrum transmitters will shift frequencies making it impossible for a thief to grab and rebroadcast your code Page 3 128 9309 3 of 24 your transmitter button is pressed more than fifty times while it is out of range of the vehicle children playing with your keys the transmitter will not operate w
6. Page 21 128 9309 21 of 24 TRANSMITTER TRANSMITTER ICON TONE VIBRATE FUNCTION BUTTON DISPLAYED SELECTION TIMING ADJUST MODE HRS TIMING ADJUST MODE MINS PRESS FOR 5 SECONDS 18 88 2 BEEP TONES PRESS 1X 18 88 ALARM CLOCK ADJUST MODE HRS ALARM CLOCK DJUST MODE MINS PRESS 2X 18 88 PRESS 3X 18 88 5 SELECTIONS PRESS PRESS 4 8 KEY BUTTON OR OPTION BUTTON TO SELECT ALARM CLOCK amp POWER UP MUSIC SELECT ALARM CLOCK ADJUST MODE ON OFF TIMING COUNT DOWN ADJUST MODE HRS TIMING COUNT DOWN ADJUST MODE MINS TIMING COUNT DOWN END MELODY SELECTION PRESS 5X ON OFF PRESS 6X 18 88 PRESS 7X 18 88 5 SELECTIONS PRESS PRESS 8X 8 KEY BUTTON OR OPTION BUTTON TO SELECT TIMING COUNT DOWN MODE SELECT ON OFF REMOTE START ON PRESS 10X 58 KEY BUTTON OR OPTION MELODY SELECT 2 BUTTON TO SELECT TRANSMITTER TRANSMITTER ICON TONE VIBRATE FUNCTION BUTTONS TO DISPLAYED OPERATION PRESS 10 MIN PARKING COUNT DOWN TIMER PRESS 9X ON OFF 5 SELECTIONS PRESS OPTION 0 10 MELODY 20 MIN PARKING MELODY COUNT DOWN TIMER HORTON 2x 0 20 30 MIN PARKING COUNT DOWN TIMER 60 MIN PARKING COUNT DOWN TIMER OPTION 0 30 MELODY OPTION 4X 1 00 MELODY 90 MIN PARKING COUNT DOWN TIMER 120 MIN PARKING COUNT DOWN TIMER OPTION 5X 1 30 MELODY MELODY OPTION 6x 2 00 PARKING COUNT DOWN TIMER OFF MODE
7. Trunk Key Buttons Page 13 128 9309 13 of 24 Other Transmitter button configurations are also available Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are Remote Car Starter O Remote Window Closure O Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter or by and independent button or combination of buttons For your vehicle this output is Controlled By L1 Trunk Key Button L1 Option Button Lock Unlock Buttons Lock Trunk Key Buttons Unlock Trunk Key Buttons Other Transmitter button configurations are also available Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are Remote Car Starter Remote Window Closure Remote Garage Door Interface To remotely operate the device ind
8. flash pattern Page 8 128 9309 of 8 of 24 You will notice the LED flashing five times pause and then flash two times pause This pattern will be repeated three times Indicating the new code 52 has been accepted and stored in memory NOTE If after step 7 the LED flashes a code other than what was just entered this indicates that the code has not been changed You will have to repeat steps 1 through 7 above being certain to note the following Acceptable digits 10ths or units are 1 through 9 The unit will not recognize a 0 Zero or no digit entered in any place units or tenths NOTE f 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code MANUALLY OVERRIDING YOUR SYSTEM USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed and the default override code of 11 is in the system s memory 1 Enter the vehicle and turn the ignition switch to the on position NOTE The siren will sound 2 Within 5 seconds press and release the Receivers push button switch 1 time 3 Within 5 seconds turn the ignition switch off then on 4 Within 5 seconds press and release the Receivers push button switch 1 time 5 Turn the ignition switch off then on and start the vehicle NOTE Ifyou have changed the programmed override code then substitute your new cod
9. three times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Again closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction If the siren horn did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual Doors Lock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when arming as an added convenience the system will turn on the headlights when the system is armed SILENT ARMING ACTIVE Feature must be active during programming During step 2 above hold the transmitter button for 2 seconds then release The unit will arm without the chirps for this one lock cycle Page 4 128 9309 of 4 of 24 Must be activated during programming 1 E the engine exit the vehicle and close and lock all doors hood lid and runk lid The dash mounted LED begins to flash rapidly indicating 30 second passive arming has begun 2 Opening any protected entry point during the 30 second passive arming cycle will immediately suspend automatic arming and the 30 second passive arming AM will restart when all doors are closed At the end of the passive arming cycle The dash mounted LED begins to flash slowl
10. ED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered If the siren did not sound when disarming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual Doors Unlock Optional L1 2 Step Doors Unlock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when disarming as an added convenience the system will turn on the headlights when the system is disarmed NI DISARMIN eature must be activated during programming During step above hold the transmitter button for unit will arm without the chirps for this one lock cycle HILE THE SYSTEM IS SOUNDING during a triggered state you wish to shut off the siren without disarming your Security system pros and release any transmitter button other than the Unlock Disarm button This action will turn off the siren yet leave the vehicle fully armed and protected This feature is particularly useful if you are aware of children ri playing near your vehicle that may accidentally lager your security system In this case you can cancel the siren sounding without isarming your alarm Page 6 128 9309 of 6 of 24 NTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle If an intrusion attempt has occurred the siren wi
11. advantage of this option programmable feature 9 must be selected for the Custom Code Option Consult your installation center for programming details The system comes from the factory with a pre programmed override code of 11 To change this default override code do the following 1 Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the on position Within 10 seconds press and release the Receivers push button switch 3 times Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time Within 10 seconds begin to enter your chosen 10ths digit by pressing and re leasing the Receivers push button switch from 1 up to 9 times Within 10 seconds of the last entered 10ths digit turn the ignition switch off then on Within 10 seconds begin to enter your chosen units digit by pressing and re leasing the Receivers push button switch from 1 up to 9 times Finish by turning the ignition switch to the OFF position If the new code was accepted the unit will report back the newly entered code by flashing the LED first indicating the 10ths digit pause and then the units digit The unit will report the new code three times with a one second pause between each code then the system will begin arming If the LED flash pattern reports the previously stored code the new code was no
12. annel 3 For Trunk Or For Remote Start 24 Hour Time Start Mode Cold Temperature Start Mode 2 or 4 Hour Automatic Start Mode Parking Meter Count Down Timer On LCD Remote Additional Count Down Timer Mode Remote Panic In All Modes Press amp Hold Lock Unlock Button For 3 Seconds To Engage Improved Custom Code Override User Selectable and Programmable Protected Push Button Valet Override Switch In Windshield Receiver 7 Function LED Arm Disarm Zone 1 Zone 2 Zone Valet Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output Additional Engine Immobilizer Output Optional Relay Required Page 2 128 9309 of 2 of 24 True Last Door Arming Hardwire Only Defective Zone By Pass Defective Zone Chirp Confirmation Unit Chirps To Report Zone Cleared 6 Tone Mini Siren Car Horn Output For Additional Alarm Response Improved Timing To Minimize RF Interference Additional Negative Trigger Input Hood and Trunk RF Inhibit With Ignition On Parking Light Flasher Relay On Board Plug In Dual Stage Shock Sensor Pre detect Full Trigger and City Mode Audible Arm Disarm Defect and Tamper Chirp Indications Headlight Control Output Illuminated Entry Control Output Active or Passive Arming Selectable Programmable Auto Lock On Off Programmable Auto Unlock On Off Drivers Door All Doors Er MARIS Door Lock Pulse
13. are 4 modes of operation that can be selected by the operator 1 Normal Operation default mode In this mode any strong vibrations will cause the siren to sound full detect for 30 seconds Any lesser vibration will cause the siren to emit about 6 short warn away chirps pre detect 2 Stage 1 Omit pre detect In this mode the warn away chirps created by the lesser vibration will be deleted If strong vibration occurs the siren will sound 3 Stage 2 Omit pre amp full detect In this mode both the pre detect stage and the full trigger stage of the sensor are defeated The unit will not react to vibration of any magnitude NOTE Shock Sensor Icon Is Displayed On The LCD Panel 4 Stage 3 City Mode In this mode the pre detect chirps will change from six pre warning tones to a full 10 seconds of warning chirps The full detect trigger duration will be reduced from 30 seconds to 15 seconds NOTE Setting the stage of the shock sensor will be effective for one arming cycle only Once the system has been disarmed the very next arming cycle will cause the sensor to default to the normal operation stage To change or adjust the shock sensor press and release the ARM button of you keychain transmitter Page 10 128 9309 of 10 of 24 1 Within 2 seconds of arming press and release the ARM button 1 time to defeat the pre detect stage of the shock sensor The lights will flash and the siren will chirp once 2 Within 2 seconds of
14. armed and the Panic Mode is activated the lights will flash unlock icon will be displayed and the siren will beep on the LCD screen URNING OFF BEEP TONES AT THE TRANSCEIVER When ever the vehicle is operated from the two way transmitter the unit 34 will beep responsive to the function executed at the vehicle 1 beep when armed 2 beeps when disarmed etc at times it may be inconvenient or too noisy to hear the beep tones so the system allows you to set the unit for vibrate mode To toggle on or off beep tones vibrate simultaneously press the F and unlock buttons The icons shown left will appear in the upper left hand corner of the screen to indicate vibrate If the alarm system has been triggered the icon displayed on the LCD transmitter will indicate which zone has been activated as well sound the beep tones or vibrate dependent upon the setting as shown above The following trigger patterns will be displayed um and the entry attempt was made to one of the vehicle oors Triggered and entry attempt was made to the vehicles Hood or Trunk o o Page 16 128 9309 of 16 of 24 hicle has been hit or bumped hard enough to cause a response from the vibration detector ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE If the arm disarm chirp tones have been turned off at the vehicle when you arm or disarm the display will indicate this as shown 2 and there will be no arm disarm chirps at the transmitter This
15. de you security system if the transmitter becomes lost or poen due to battery failure Reading the sections on Manually Overriding Your System is necessary to fully understand the procedure required to enable your vehicle in such situations In addition the chart on page 23 of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected Although the default mode is Valet Switch operation the system can be configured for Custom Code operation for enhanced security Confirm the override mode selected on page 23 of this manual and familiarize yourself with the section on it s operation FEATURES 1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control Six Channel Code Learning Programmable Receiver External Superheterodyne Transceiver Antenna w Push Button Switch amp LED Single Or Two User Programmable W Separate Control Outputs Single Button Lock Unlock or Separate Button Lock Unlock or Both sm Keyless Entry With Optional Access Guard must have power door ocks Selectable Manual Override Mode New Enhanced Panic Feature Any button other than unlock stops siren no change to the units state Smart Disarm If triggered elect to shut off siren or disarm entire unit Adjustable Shock Sensor Via The Transmitter Pre Detect Off Pre amp Full Detect Off City Mode Safe Start Output Controlled From Channel 3 Option Ch
16. e in emergency situations To use remote panic 1 Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds The alarm will immediately sound 2 To stop the alarm press and hold the Lock or Unlock button on the transmitter for 3 seconds If the button is not pressed the alarm will automatically stop after 30 seconds Also if any transmitter button other than the Lock or Unlock button is pressed and released the Panic mode will be turned off immediately The normal function of this transmitter button will be suspended during the Panic sounding period During the panic mode the Lock and Unlock buttons can be used to lock and unlock the doors if the option is installed however once the unlock disarm button is pressed the vehicle s starter inhibit device where installed will be disabled allowing the vehicle to start NOTE While in the Panic mode pressing and releasing the Lock or Unlock buttons will if the option is installed lock and unlock the doors respectively While in the panic mode anytime the Unlock button is pressed the panic feature will continue for the allotted 30 seconds however the security system will be disarmed allowing the vehicle to start RE SHOCK SENSOR MODE SELECTION The way in which your alarm system reacts to threatening vibrations created by attempts to enter the vehicle by breaking a window is adjustable by the transmitter immediately after arming There
17. e tenths for step 2 above and units for step 5 above You can selectively eliminate the normal arm and disarm chirps by holding the transmitter button slightly longer when arming or disarming This will prevent the siren chirps for one arm or disarm cycle If you find this inconvenient and wish to eliminate these chirps permanently 1 Turn the ignition switch on then off 2 Within 10 seconds of turning off the ignition press and release the Receivers push button switch 3 times 3 If the chirps were on before you started the siren will emit 2 short chirps indicating that the chirps are now off If the chirps were off before you started the siren will emit one short chirp indicating that the chirps are now on NOTE If the vehicle battery is disconnected then reconnected the unit will return to the default setting of chirps on Repeat the above procedure to eliminate the arm disarm chirps NOTE Your system must be programmed by the installation center to enable this feature NOTE Whenever the chirps are bypassed the 4 chirp intrusion indicator and 3 chirp defective zone indicator will always operate Since these are important warnings to you that something has happened they cannot be eliminated system must be programmed by the installation center to enable this eature Page 9 128 9309 9 of 24 REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for us
18. feature selection menu of your system Check with your installing dealer to ensure this feature is set to the on position Light The Display Press and release the F Function button one time The display will illuminate for 10 seconds Vibrate Or Tones Press the and unlock buttons simultaneously to toggle this feature on and off Daily Start Timer Only available on certain remote start units 24 Hour Start Timer Standing at the vehicle at the time you want it to A start press the option lock buttons simultaneously for 1 second The 24 transmitter will beep and display the 24 hr timer This is the time the vehicle will start when you follow the exit procedure In other words if you want the vehicle to start 6AM at 6AM of any morning standing at the vehicle press and hold the option lock buttons until you hear a beep and the 24 hr timer is displayed This establishes a starting time The Remote Start unit will start at the prescribed time once only This function must be activated by following the procedure below each time you want the vehi cle to start at the prescribed time Page 18 128 9309 of 18 of 24 To activate this function a Turn the ignition switch off b Within 10 seconds of step a depress and hold the brake pedal while press ing the key icon transmitter button 2 times c The unit will emit 2 chirps the transmitter will beep and the 24 Hour start timer icon on the display will remai
19. has the ability to be configured to a single press start if you so desire Please check with your installation center if your system was changed from the default safe start setting of two press start or if you wish to change your configuration WARNING Do not turn the key to the start position This will cause the starter motor to engage with the already running engine which could result in damage Step on the brake pedal to disengage the remote start unit The vehicle will continue to run but now on it s own power NOTE The engine will stop running before the expiration of the pre programmed run timer if you complete any of the following Press and release the programmed channel of your keychain transmitter two times within 2 seconds Depress the brake pedal Open the hood Move the red handled control switch to the off position Race the engine to above 4000 RPM OPERATING ON AUTOMATIC START UP TIMER MODE Your system has the ability to start the vehicle every 2 or 4 hours over a 48 hour period This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine WARNING Be certain that the vehicle is outdoors before using this or any remote vehicle starting device Arunning engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged 1 Turn
20. hen you return to the vehicle and Will need to be re aligned to the receiver To do this simply press button 1 lock two times within a one second time period The system will now respond to that transmitter each time a button is pressed NOTE This system is custom configurable and can be set up to operate with a number of options controlled from any transmitter button or button combination For reference we will describe operation assuming that your system is programmed for separate lock and unlock buttons Also reference will be made to the icons as shown on the buttons left NOTE The LCD based remote will be explained in detail further in this manual See System Status described later in this manual Consult your installation center if your system has been configured differently NOTE Your system has the option of using a siren the vehicle horn or both for the sounding device Where the siren is referenced below the horn or both may in fact chirp or beep ARMING THE SYSTEM ACTIVE 1 Turn off the engine exit the vehicle and close all doors hood lid and trunk lid 2 Press and release Lock Arm button on the keychain transmitter The dash mounted LED begins to flash slowly Parking Lights flash one time Siren sounds one chirp If the siren horn sounds 3 chirps then you have left a door trunk or hood lid ajar Simply close the opened entry point to provide full protection Ifthe e siren chirp
21. icated momentarily press or press and hold the appropriate transmitter button s as indicated above Channel 7 is an alternate output that can be controlled by the unlock button of the transmitter or by any independent button or combination of buttons For your vehicle this output is Controlled By L1 Trunk Key Button L1 Option Button Lock Unlock Buttons L1 Lock Trunk Key Buttons Unlock Trunk Key Buttons Page 14 128 9309 of 14 of 24 Other Transmitter button configurations are also available Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are O Remote Window Closure L1 Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above This system provides a means to cool down the vehicles turbo charger if so equipped allowing the vehicle to continue to run for a prescribed period of time every time the vehicle s engine is turned off This feature requires the system to be set up for turbo timer during installation Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run 3 5 or 10 mi
22. is true if the transmitter is set for vibrate mode as well ea Triggered and entry attempt was made to the vehicles glass or the ve When the vehicle is armed and a door is opened or ajar the transmitter will chirp 3 times the lights will flash and the display will indicate a door trigger as shown above When the door is closed or the zone clears the transmitter will chirp 1 time and the display will clear When the vehicle is armed and the hood or trunk is opened or ajar the trans mitter will chirp 3 times the lights will flash and the display will indicate a hood or trunk trigger as shown on the previous page When the hood or trunk is ora or the zone clears the transmitter will chirp 1 time and the display will clear PROGRAMMED TRANSMITTER NOTIFICATION PTN Every time after Disarm when the ignition key is turned on the unit s LED will report the number of transmitters programmed into the system This safety feature will alert you if an unauthorized transmitter has been programmed into your vehicle s security system acta pt knowledge from the factory there will be a 2 flash pause repeated 3 times indicating that two transmitters are programmed into the system If you note additional flashes there may have been an additional transmitter added without your knowledge or authorization If you notice a change in the transmitter LED report pattern you can correct this by looking up how to erase and reprogram your transmit
23. ity to operate the equipment NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment Page 23 128 9309 23 of 24 PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS BANK 1 Transmitter Model Name 145SP or 5BCR14SP Is Also Found On Back Of Transmitter Case Use Battery CR2032 For 145SP amp AAA For 5BCR14SP 1 Turn the koy lo the on position 2 Press and release the switch 3 times Siren Chirps 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren lun the ignition switch off The above action programs the Lock Unlock Start Trunk and Option 1 buttons which typical for most systems or additional channel programming beyond the option 1 button you can use any unused button or combination of buttons not in use In other words to access option channel 5 6 7 you would do the following From step 3 above a Press and release the valet programming button 4 additional times to get to channel 5 then press any unused transmitter button or button combination to program b From a press and release the valet programming button 1 time to get to channel 6 then press any unused transmitter button or button combination to program c From b press and release the valet program
24. ll chirp 4 times and the parking lights will flash 3 times when disarming the system Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered If the LED is flashing one time pause one time pause etc then an intrusion attempt was made to the shock sensor or an accessory triggering device that may have been added to the system If the LED is flashing two times pause two times pause etc then an intrusion attempt was made to a hood or trunk pin switch that was added to the system or to a light activated entry point if the alarm was installed using the voltage sensing feature If the LED is flashing three times pause three times pause etc then an intrusion attempt was made through one of the vehicle s doors These intrusion warning indicators are stored in the system s memory and will only be erased when the ignition key is turned on PUSH BUTTON LED RECEIVER VALET OVERRIDE SAFETY SWITCH The Push Button LED switch located in the receiver allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking atten dants or garage mechanics When the system is in valet mode all alarm functions are bypassed however the remote panic feature and remote door locks will remain operational To use the valet mode the system must first be disarmed either by using your keychain transmitter or by activating your personalized manual override code 1
25. ming button 1 time to get to channel 7 then press any unused transmitter button or button combination to program NOTE Not all systems have channels above 3 check with your installation center for options your system may or may not have NOTE Certain systems have the ability to utilize channels 6 amp 7 for driver priority programming For driver priority the vehicle must be equipped with this feature and the optional feature must be set up and installed by your installation center Once this feature is added when the unlock button of transmitter 1 16 used it will set driver 1 priority and when the unlock button of transmitter 2 is used it will set driver 2 priority In this situation the unlock button can be programmed into two receiver channels unlock channel 2 and driver priority 6 7 In other circumstance will the system allow a transmitter button to be programmed into 2 receiver channels at the same time This unit s transmitters can control two vehicles with Prestige Remote Systems To toggle primary or secondary vehicle press lock and trunk key buttons simultaneously for 5 seconds Transmitter Battery Replacement 1 Locate and remove the 00 point Phillips head screw on the back of the transmitter case 2 Carefully separate the front case from the rear 3 Slide the CR2032 battery out from under the battery clip and dispose of properly 4 Install the new battery with the side facing up away from the circuit b
26. minutes The transmitter will emit a beep tone when the timer expires to remind you to get back to your vehicle See following chart for setting the parking meter count down timer feature Alarm Clock Mode The transmitter has a built in alarm clock that can be set to beep at a cer 3 tain time each day The alarm clock mode must be set and the feature turned on To use this feature please refer to the chart on the following page NOTE Your system is shipped with two transmitters 1 two way shown on the left and the one way transmitter shown right The one and two way transmitters are programmed from the factory with separate lock amp un Page 19 128 9309 19 of 24 lock buttons the trunk key icon button operates remote start and remote trunk release where ap TUE plicable The option button and any button com 4 ination may be programmed to operate various options Consult your installation center for button programming and options that may have been added to your vehicle Although this is the default programming from the factory this can be changed for you to any configuration you prefer Please refer to the ransmitter program guides included with your kit NOTE A maximum of two of either style transmitter may be programmed to your unit BATTERY INDICATOR Your transmitter has a battery indicator that is shown in the upper right 111 corner of the screen as shown left This icon indicates a new batte
27. mode and will not start from RF or any other input Posse or otherwise To Exit R S Override Mode 1 With the system disarmed press and hold the push button found on the wind shield receiver in 2 Turn the ignition switch on off on off on off 3 The LED turns off indicating that the R S unit is fully functional one again The system WILL NOT start the vehicle if any one ofthe following conditions exists 1 The Vehicle Hood Is Opened 2 The Gear Selector Is In Any Gear Other Then Park 3 The Brake Is Depressed 4 The Safety Control Switch Is In The Off Position WARNINGT Be certain that the vehicle is outdoors before using this or any remote vehicle starting device Arunning engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged Page 11 128 9309 11 of 24 REMOTE START THE VEHICLE Press and release the programmed channel of your keychain transmitter two times within 2 seconds The vehicle will start and remain running for the pre programmed 5 10 15 or 20 minutes As a visual indication the parking lights will flash or turn on depending on the programming set up by your installation center When you arrive at your vehicle disarm the alarm system by pressing and releasing the arm disarm button of your keychain transmitter Enter the vehicle and turn the ignition key to the on position NOTE This system
28. n on The vehicle will start at the set time 24 hours from when set To toggle this feature off press the option lock buttons simultaneously until a beep Is heard and the 24 hr timer turns off NOTE The unit will start once and run for the prescribed time If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide NOTE To insure accurate 24 Hour Start up it is advisable to reset the start time periodically as time may drift slightly each day Timing Count Down The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important For instance 7 you may have a meeting 4 hours from now and you want a reminder in 3 Hrs and 45 Mins This additional count down timer allows you to set the count down up 19 Hours and 59 Minutes from the current time and when the timer reaches zero the transmitter will emit a tone or vibrate depen dent on your preferred setting See chart for setting the count down time for this feature Valet When the System is in the valet mode the icon shown will show in the z7 display when the status check buttons are activated Parking Meter Counter The transmitter has a built in clock that can count down from 10 20 30 60 90 or 120 minutes This feature is useful when parking the vehicle in a metered parking lot If the time on the parking meter is 30 minutes you can set the count down timer to 20
29. ntrolled By Trunk Key Button Other Transmitter button configurations are also available Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system This security system is equipped with an output which will activate when the ap propriate transmitter button is depressed for 4 seconds Although this output is intended to activate the trunk release option any other optional devices may be connected to this channel Consult your installation center for more information about this output ADDITIONAL REMOTE FUNCTION CHANNEL 4 Controlled By L1 Trunk Key Button L1 Option Button L1 Lock Unlock Buttons 1 Lock Trunk Key Buttons Unlock Trunk Key Buttons Other Transmitter button configurations are also available Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are Remote Car Starter O Remote Window Closure Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above Controlled By L1 Trunk Key Button L1 Option Button L1 Lock Unlock Buttons 1 Lock Trunk Key Buttons Unlock
30. nutes after the ignition switch is turned off To activate the turbo timer Anytime the engine is running for more than 15 seconds 1 Place the gear selector in park 2 Set the parking hand brake 3 Be certain your foot is off the brake pedal 4 Press the receiver s program Push Button switch 2 times within 5 seconds The parking lights will flash two times indicating the mode was successfully entered If your parking lights flashed four times this indicates the turbo mode was on and is now turned off With the turbo timer mode selected on after you ve arrived at your destination while the engine is still running set the parking brake pause 2 seconds then turn the ignition switch to the off position The engine will continue to run the allotted time according to the selection during installation If you do not want the vehicle to continue to run for one cycle simply step on the vehicle s brake or release the parking brake or activate the transmitter s start button two times in succession Any of these will cause the engine to turn off This system has the ability to have a Telematic Upgrade module connected to it This is a upgrade that can give you control of certain functions of your vehicle from a Telephone or in some cases a computer interface Please check with your installation center for most recent Telematic Upgrades If you had a Telematic Up grade installed the manual supplied with the upgrade unit will provide a o
31. oard 5 Close the case and reassemble in reverse of disassembly To purchase replacement transmitters or to get additional product information go to www prestigecarsecurity com PATENTED www voxxintl com company patents 2014 Voxx Electronics Corporation 150 Marcus Blvd Hauppauge NY 11788 128 9309 Page 24 128 9309 of 24 of 24
32. ow the exit procedure In other words if you want the vehicle to start 6AM at 6AM of any morning standing at the vehicle press and hold the option lock buttons until you hear a beep and the 24 hr timer is displayed This establishes a starting time The unit will start at the prescribed time once only This function must be selected each time you want the vehicle to start To activate this function a Turn the ignition switch off b Within 10 seconds of step a depress and hold the brake pedal while pressing the key icon transmitter button 2 times c The unit will emit 2 chirps the transmitter will beep and the start timer icon on the display will remain on The vehicle will start at the set time To toggle this feature off press the option lock buttons simultaneously until a beep is heard and the 24 hr timer turns off This icon will appear when the temp start mode is activated The vehicle will start one time automatically when the temperature reaches 0 WARNING Be certain vehicle is outside before activating this mode To toggle this feature on of off from the Locked Armed mode press the Option and Lock buttons simultaneously Available on certain remote start models only Throughout this manual you will find screen shots where they apply if using the two way transmitter If using the one way transmitter while the two way transmitter is within range of the vehicle the two way transmitter will update it s screen
33. perators manual advising of the features of the system and means available to control these features of your vehicle TRANSCEIVER ICONS AND THEIR INDICATIONS Refer to the LCD Transceiver Located On Page 18 and it s call outs which will be referred to in the following feature descriptions Page 15 128 9309 15 of 24 When Disarmed Press the Arm Lock button to Lock and the System f The Lock Icon is displayed on the LCD panel amp the parking lights flash once n When Armed Press the Disarm Unlock button to Unlock and Disarm the System The Unlock Icon is displayed on the LCD panel and the parking G lights flash twice Amm When the Key Icon Button Has Been Operated for seconds the trunk open Sam icon will flash on the LED Screen When the Key Icon Button is pressed 2 times in succession The reverse circle is epa on the LCD screen while the vehicle is running This icon will flash and the hour glass will indicate count down timer based on the run time set up by your installation center When the unit shuts off the Icon will turn off and the transmitter will play a melody NOTE Engine can be started in many modes armed disarmed valet etc The screen will display multiple icons indicative of these modes When the Panic Mode has been activated and the system is armed the vehicle s lights will flash the siren and lock icon will be displayed on the LCD screen and the siren will beep If the system is dis
34. ry shown with 3 bars As the battery deteriorates the bars will disappear bar indicates the battery should be replaced Replace battery with a fresh 1 5V AAA battery and dispose of the used battery properly Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote RANGE INDICATOR The range indicator will have bars to the side of the icon if the unit is out of range VIBRATE MODE ON This icon will be displayed if you select vibrate instead of tones To toggle vibrate on and off press F Unlock simultaneously ALARM CLOCK This icon will be toggled on and off when the F Trunk Key buttons are pressed simultaneously The feature must be set in the feature selection menu of the transmitter COUNT DOWN TIMER The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important Setting information shown on previous page POWER SAVE FEATURE Press the F and Lock buttons simultaneously to toggle this feature on and off With this mode on the battery in the transmitter will go into a power down mode when the unit is disarmed Page 20 128 9309 of 20 of 24 Standing at the vehicle at the time you want it to start press the option 24 lock buttons simultaneously for 1 seconds The transmitter will beep and display the 24 hr timer This is the time the vehicle will start when you fol l
35. step 1 press and release the ARM button 2 times to defeat the pre and full detect stages of the shock sensor The lights will flash and the siren will chirp twice 3 Within 2 seconds of step 1 press and release the ARM button 3 times to enter uc i Mode of operation The lights will flash and the siren will chirp three imes While under control of the remote start the system can be programmed to allow you to shunt the shock sensor from the transmitter If the system has been programmed simply press the lock button of your keychain transmitter anytime during the remote start cycle The shock sensor will be shunted for the entire run cycle and will resume normal operation after the remote start unit shuts off Check with your installation center to determine if this feature has been programmed into your system PUSH BUTTON LED RECEIVER SAFETY CONTROL SWITCH The Push Button LED control switch allows you to temporarily disable the remote starting function of the system This recommended whenever the vehicle is being serviced To place the system in the service mode 1 With the system disarmed unlocked and the ignition switch off press and hold 2 Turn the ignition switch on off on off on off 3 The LED begins to flash two short flashes followed by one long flashes and continues this pattern until returned to normal mode of operation This puts the unit into the R S Override mode indicating that the remote start is in the service
36. t entered correctly Please repeat steps 1 through 7 above considering the following NOTE Acceptable digits 10ths or units are 1 through 9 The unit will not recognize a 0 Zero or no digit entered in any place units or tenths NOTE f 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code CUSTOM CODE PROGRAMMING EXAMPLE To Change the code from the factory pre assigned code O you would do the following 1 Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the on position Within 10 seconds press and release the Receivers push button switch 3 times Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time Within 10 seconds begin to press and release the Receivers push button switch to set the tenths digit As per the example press and release 5 times to set the tenths digit to 5 Within 10 seconds of the last press of the pushbutton turn the ignition switch off then on Within 10 seconds begin to press and release the Receivers Push button switch to set the units digit As per the example press and release 2 times to set the units digit to 2 Turn the ignition switch to the off position Immediately observe the LED
37. ters found in the transmit ter programming guide This reprogram operation will erase all unauthorized or unwanted transmitters Page 17 128 9309 17 of 24 ADDITIONAL REMOTE FEATURES e two way remote control unit allows you to access status information from the vehicle check temperature light the display toggle the transmitter from beep tones to vibrate mode initiate daily start timer and temperature start Selection of these and other features are shown below NOTE Transmitter must be within operating range of the vehicle approximately 3000ft lt lt Option lt Function Button Press the lock key option buttons simultaneously for 1 second The vehicle s alarm will display the systems current status Check Temperature Only available on certain remote start units Press the option key buttons simultaneously for 1 second The vehicle s alarm will display the temperature Temperature is read from the alarm s module located below the dashboard This reading may be higher than actual ambient temperature due to the greenhouse effect and is relative only to the inside vehicle temperature Temperature Start Mode Available on certain models toggle this feature on or off from the armed mode press the Option amp Unlock Buttons simultaneously the temperature icon appear on or disappear from the display and the transmitter will emit a tone NOTE This feature must be active in the
38. the ignition key on then off 2 Within 10 seconds activate the RF start command two times Push the pro grammed channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated The vehicle on a 2 or 4 hour interval basis will automatically start run for the pre programmed time 5 10 15 or 20 minutes and then shut off This will continue for 48 hours NOTE The automatic start up timer can also be initiated from the keychain trans mitter To do this Page 12 128 9309 of 12 of 24 1 Start the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times 2 Shut off the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times 3 Within 10 seconds of step 2 activate the RF start command two times Push the second channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated To cancel the automatic start up timer do one of the following 1 Sa En vehicle manually with the use of the ignition key and depress the brake pedal 2 Remote start the vehicle using your keychain RF transmitter NOTE Option button used in combination is only available on the alternate remote transmitter and not available on the LCD Transmitter Co
39. y Parking Lights flash one time Siren sounds one chirp If the siren did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual L1 Doors Lock Optional Door locking during passive arming is a selectable feature The alarm can be pro grammed to allow the doors to lock only when arming using the keychain transmitter and they will not automatically lock during passive arming PROTECTION WHILE THE SYSTEM IS ARMED Opening any protected door hood or trunk lid will cause the alarm to immediately sound The alarm will continue to sound for 30 seconds then stop and continue to monitor all protected entry points If the thief left a door opened the alarm will sound for six 30 second cycles remain armed and ignore that triggered zone Whenever the system is armed the dash mounted LED indicator will slowly flash This serves as a visual deterrent to the potential thief The LED is a very low current bulb and will not cause the vehicle s battery to drain even when left unattended for extended periods Whenever the system is triggered the vehicle s parking lights will flash for the full 30 second alarm cycle attracting visual attention to the vehicle Optional Whenever the system is armed the vehicle s starting circuit will be bypassed If the thief should choose to ignore the siren the vehicle can not be started
Download Pdf Manuals
Related Search