Audiovox 640 User's Manual
Contents
1. Scribe a center line on the sheet metal roof of I PREPARATION OF VEHICLE INTERIOR 1 Remove and retain O E dome light by gently prying downward on rear edge of lens then slide frame assembly out Disconnect wiring and lay dome light in a safe place See Fig 1 FIGURE 1 reference location carefully measure amp trim headliner as shown Caution Before cutting headliner material check for wiring or other componentry above headliner Cut only where indicated Make sure that the 7 cut is centered left to right in vehicle See Figure 2 DO NOT OVERCUT HEADLINER the vehicle in front and rear of openings in headliner This will be used for bracket alignment See Figure 2 r vs re gt Fr ae FS FIGURE 2 4 Install mounting bracket item 6 pg 2 with the bent edges upward Slide bracket rearward until rear tabs engage rear O E roof brace Align notches in bracket with center lines scribed on roof See Fig 3 and Fig 4 5 Secure front of bracket to front roof brace using 2 two 10 X 1 2 screws item 1 pg 2 FIGURE 3 6 Make sure tabs on mounting bracket engage O E roof brace and notch aligns with center line See Figure 4 FIGURE 4 7 Construct a jumper harness that will connect the vehicle s dome light wires to the lights in video system Connect the white wire to the O E pink wire Connect the black wire to the O E yellow wire See Figure 5 8 Using a test light test function of2. 7 FIGURE 7 13 14 15 16 Release video screen from locked position Lower video screen to viewing position for access to mounting location in top of video system housing Raise video system into approximate position and connect all wiring to components Connect wiring and cabling to video system per instruction included with video system Check function of all component and lights See operating instruction for video system operations check For further assistance refer to the video system manual for the technical support phone number listed for your area FIGURE 8 Insert video system into opening in console Note Make sure wires do not get pinched between video system and console Align holes in housing with clips in mounting bracket Secure using 4 four 6 32x 3 4 screws item 2 pg 2 and 4 four 3 5mm washers item 3 pg 2 See Figure 8 Caution Do not overtighten screws 17 Tighten screw previously installed to secure rear of console to headliner Caution Do not overtighten screws or damage to vehicle roof may occur 18 Raise video screen into locked position 19 Install speaker grille tem 7 pg 2 Align clips in grille with holes in console and press firmly See Figure 9 20 If speaker upgrade kit was not installed install cover plate item 9 pg 2 at front of console and secure using 2 6 X 1 2 screws item 5 pg 2 21 Install cover plate decal item 10 pg 2 FIGURE 9
3. INSTALLATION INSTRUCTIONS FOR 50 0305x 015 SERIES 1181272 1999 DODGE DURANGO OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter Awl or similar tool 4 Razor knife or similar 18 GA wire 4 6 6 1 4 Hex Socket Bit Test light 8 Audiovox Series 640 650 Video Module oe NOT FOR VEHICLES EQUIPPED WITH SUN ROOF NOT FOR USE IN VEHICLES EQUIPPED WITH FACTORY REAR A C Nov 8 1999 INSTALLATION INSTRUCTION 44 0044A Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ITEM Description QTY 1 1 SCREW 10 X 1 2 HWH 2 2 SCREW 6 32 X 3 4 PPH 6 3 WASHER 3 5 mm 4 2 4 SCREW 8 X 1 1 2 PWH 1 5 SCREW 6 X 1 2 PFH 2 3 6 MOUNTING BRACKET 1 7 SPEAKER GRILLE 1 4 8 CONSOLE 1 9 COVER PLATE 1 10 COVER PLATE DECAL 1 5 INSTALLATION INSTRUCTION 44 0044A Nov 8 1999 Printed in the U S A U Using the front edge of dome light opening as a
4. lights 9 Install O E dome light in original manner FIGURE 5 10 Install and route all video and audio cables and any other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to B pillar Down the B pillar to the floor Route the power lead to an accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring RCA plugs Remote Sensor extension etc to the VCP location See Figure 6 Connect per instructions included with the video system If video system if to be used as a television install an appropriate antenna per instructions included with the antenna FIGURE 6 II INSTALLATION OF CONSOLE IF SPEAKER UPGRADE KIT WAS PURCHASED INSTALL PER INSTRUCTIONS PROVIDED 11 Raise console item 8 pg 2 into approximate position against headliner Loosely install using 2 two 6 32 x 3 4 screws item 2 pg 2 through the smaller holes in bracket on console into threaded clips on front mounting bracket See Figure 7 12 Using a scribe or similar tool align hole in rear of console with slot in rear mounting bracket Loosely secure rear of console using 1 one 8 x 1 1 2 screw item 4 pg 2 Make sure console alignment is straight then tighten 2 two 6 32 screws previously installed See Figure
Download Pdf Manuals
Related Search