Audiovox 50-0245x-002 SERIES User's Manual
Contents
1. be used as a FIGURE 4 television install an appropriate antenna per instructions included with the antenna 6 Construct a jumper harness that will connect the vehicle s dome light wires to the lights in video system Connect the white wire from video system to the O E black blue wire Connect black wire from video system to the chassis ground 7 Place the overhead console in vehicle and loosely fit it against headliner Check that console is centered in vehicle and matches all contours of headliner Using an awl or similar tool align the rear mounting hole with hole in bracket Apply upward pressure to console and secure using 1 one 8 x 3 4 screw See Fig 5 Release video screen from locked position and mark the locations of the mounting bosses in the video system on the mounting bracket using an awl or similar tool Remove console from vehicle 8 Using 3 32 4 four holes in mounting bracket at locations previously marked 9 Raise console into approximate position and connect all wiring to components Route video cable through hole in bracket and connect wiring and cabling to video system per instructions included with video system 10 Check function of all components and lights See operating instructions for video system operations check For further assistance refer to the video system manual for the technical support phone number listed for your area 11 Carefully position console against headliner2. INSTALLATION INSTRUCTIONS FOR 50 0245x 002 SERIES 1181285 50 0245x 014 SERIES 1181286 FORD EXPLORER OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 3 32 drill bit 4 Razor knife or similar 5 Awl or similar tool 6 18 GA wire 4 6 7 Audiovox Series 640 650 Video Module July 7 1999 INSTALLATION INSTRUCTION 44 0026B Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ITEM Description QTY SCREW 8 X 3 4 3 PWH A 1 MOUNTING BRACKET 1 CONSOLE 1 2 I PREPARATION OF VEHICLE INTERIOR 1 Carefully trim headliner as shown Caution Before cutting headliner material check for wiring or other componentry above headliner Cut only where indicated Make sure that the 8 1 2 cut is centered left to right in vehicle See Figure 1 2 Remove and retain 2 two O E screws which secures O E bracket to roof brace
3. Release video screen from locked position Lower video screen to viewing position for access to mounting locations in top of video system housing and align holes in housing with holes in mounting bracket Secure using hardware supplied with video system See Figure 5 Caution Do not overtighten screws Make sure that wires do not get pinched between bosses on video system and mounting bracket Close video screen 12 Secure rear of console using 1 one 8 x 3 4 screw item 1 pg 2 See Figure 5 FIGURE 3
4. See Fig 1 FIGURE 1 3 Install console mounting bracket item 2 pg 2 over O E bracket on roof brace Secure rear of bracket using 2 two O E screws Secure front of bracket using 2 two 8 x 3 4 screws item l pg 2 See Figure 2 FIGURE 2 II PREPARATION OF CONSOLE FOR INSTALLATION 4 Install the video system in console item 3 pg 2 and secure using hardware supplied with video system Start all screws before tightening Begin with the rear center screw then alternately tighten screws around the perimeter of pod See Figure 3 Refer to owner s manual supplied with video system Caution Do not overtighten screws INSTALLATION INSTRUCTION 44 0026B July 7 1999 Printed in the U S A INSTALLATION OF CONSOLE 5 Install and route all video and audio cables and any other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to B pillar Rearward to the C pillar Down the C pillar to the floor Route the _ ACCESSORY CONTROLLED SOURCE power lead to an accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring RCA plugs Remote Sensor extension etc to the VCP location See Figure 4 Connect per instructions included with the video system If video system if to
Download Pdf Manuals
Related Search