Audiovox 1187001PL User's Manual
Contents
1. vehicle s dome light wires to the lights in video system Connect the red black wire from video system to the O E yellow purple wire Connect the purple wire from video system to the O E yellow wire Connect the black wire from video system to the O E pink wire See Fig 6 other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to the C pillar Down the C pillar to the floor Route the power lead to a fused accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring RCA plugs Remote Sensor extension etc to the VCP location See Figure 5 Connect per instructions included with the video system If video system if to be used as a television install an appropriate antenna per instructions included with the antenna i bo a lt x SS eee eee ae ee b x 3 Pp p arana j k Aa aa eee 3 P TEY eae 5 i m To ee Te ae a J 4 4 a z gt A r j BOE gt PEEN a E neS _ k ur in he z r 4 Eps x ol amp ai mp f sr S af fana FIGURE 6 geen Is VENEEN ERE FIGURE 7 9 Install A C switch into rear of console item 6 pg2 and O E bracket over A C switch Make sure control snaps securely into bracket See Figure 8 10 Secure bracket to con2. INSTALLATION INSTRUCTIONS FOR 55 0401x 121 SERIES 1187001PL 2001 DURANGO OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 Awl or similar tool 4 Digital Volt Meter 5 18 GA wire 9 6 Rubbing Alcohol 7 5 16 Hex Socket Bit 8 Razor knife or similar 9 Pencil or equivalent 10 Measuring tape 11 Masking tape 12 Audiovox Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF 128 6067 Feb 13 2001 INSTALLATION INSTRUCTION 44 0091A Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ITEM Description 1 2 SCREW 8 X 9 16 PWH SCREW 10 X 1 2 HWH TEK SCREW 6 32 X 3 4 PPH WASHER 3 5 mm MOUNTING BRACKET CONSOLE TEMPLATE QTY 2 2 INSTALLATION INSTRUCTION 44 0091A Feb 13 2001 Printed in the U S A I PREPARATION OF VEHICLE INTERIOR 1 Remove and retain rear A C controls by pulling downward D
3. isconnect wire harness See Figure 1 Set controls in a safe place for reuse later FIGURE 1 2 Cut template item 7 pg 2 in area 1 Locate and tape template to the headliner Make sure template is centered left to right in vehicle and mark area to be cut Remove template and trim headliner Cut template areas 2 amp 3 and reinstall the template to the headliner Ensure area 1 of the template hole locations are aligned with the OEM bracket holes Mark and trim headliner The rear cutout is critical do not overcut or the opening will be visible when the console is installed See Fig 2 Caution Before cutting headliner material check for wiring or other componentry above headliner Cut only where indicated FIGURE 2 3 Remove and retain O E A C switch bracket and screws See Figure 3 FIGURE 3 4 Carefully pull 3 A C wire harness clips from roof brace to extend length of wire harness It may be necessary to lower the driver s side of headliner at the B pillar to gain access to the 3 clip See Fig 4 Use caution when pulling on wire harness and pulling downward on headliner The connector should reach the rear cut out in headliner when all clips are released FIGURE 4 P porrn z 5 Install and route all video and audio cables and any PEER p ao P a CABLES A FIGURE 5 6 Using a digital volt meter check function of lights 7 Construct a 3 jumper harness that will connect the
4. sole brace using 2 two 8 x 9 16 screws item 1 pg 2 See Figure 8 Remove and retain mounting bracket and screws items 5 amp 3 pg2 from console item 6 pg2 Use rubbing alcohol to clean sheet metal in the cut out area in headliner Wipe surface dry with a clean cloth Remove protective tape from adhesive strips on mounting bracket item 5 pg2 Make sure bracket is centered prior to pressing tape against roof surface Once the tape is applied to the roof DO NOT REMOVE AND REPOSITION or the tape will not stick properly Install using 2 two O E screws in original holes and 2 two 10 x 1 2 TEK screws item 2 pg2 See Figure 7 FIGURE 8 14 15 16 17 II INSTALLATION OF CONSOLE 11 Raise console item 6 pg 2 into approximate position against headliner Connect O E wiring to A C control 12 Insert plastic flange on rear of console into opening in headliner Make sure console is centered left to right See Figure 9 13 Secure console secure front of console using 2 two 6 32 x 3 4 screws item 3 pg 2 FIGURE 9 Release video screen from locked position Lower video screen to viewing position for access to mounting locations in top of video system housing Raise video system into approximate position and connect all wiring to components Connect wiring and cabling to video system per instructions included with video system Check function of all components and lights See operating in
5. structions for video system operations check For further assistance refer to the video system manual for the technical support phone number listed for your area FIGURE 10 Insert video system into opening in console Note Make sure wires do not get pinched between video system and console Align holes in housing with holes in mounting bracket Secure using 4 four 6 32 x 3 4 screws and 4 four 3 5 mm washers items 3 amp 4 pg2 See Figure 10 Caution Do not overtighten screws 18 Raise video screen into locked position
Download Pdf Manuals
Related Search