Audiovox 1181279 User's Manual
Contents
1. overtighten screws Raise video screen into locked position Install speaker grille item 12 pg 2 Align clips in grille with holes in console and press firmly See Fig 13 If speaker upgrade kit was not installed install cover plate item 13 pg 2 at rear of console and secure using 2 two 6 X 3 8 screws item 5 pg 2 See Figure 13 Install cover plate decal item 14 pg 2 Install dome light in original manner FIGURE 13 a A2. D SEE FIGURE 9 FOR SUGGESTED LOCATIONS Sa l E oot FIGURE 9 HI INSTALLATION OF CONSOLE NOTE Additional assistance in mounting the overhead console in vehicle is advised to prevent damage to console or components Caution Do not overtighten screws Use extra support for the console until secured to the vehicle failure to do so may cause damage to console or installed components 13 Install and route all video and audio cables and any other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to B pillar Down the B pillar to the floor and underneath scuff panel Up the passenger s side kick panel and across the bottom side of dash panel Route the power lead to a fused accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring RCA plugs Remote Sensor extension etc to the VCP location See Figure 10 Connect per instructions included with the video system If video system if to be used as a television install an appropriate antenna per instructions included with the antenna 14 Construct a jumper harness that will connect the vehicle s dome light to the black and white wires from the lights in video system FIGURE 10 15 Raise console item 11 pg 2 into approximate position and connec
3. INSTALLATION INSTRUCTIONS FOR 50 0285x 015 SERIES 1181279 CHEVROLET VENTURE OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 T 15 TORX bit driver 4 Razor knife or similar 5 Awl or similar tool 6 1 4 hex socket bit 7 18 GA wire 4 8 Audiovox Series 640 650 Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF June 2 1999 INSTALLATION INSTRUCTION 44 0034A Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ITEM Description QTY 1 SCREW 10 X 1 2 HWH 7 2 SCREW 8 X 3 4 PWH 6 1 3 SCREW 6 32 x 3 4 PPH 6 4 WASHER 6 4 5 SCREW 6 X 1 2 PFH 2 2 6 FRONT MOUNTING BRACKET 1 7 REAR MOUNTING BRACKET 1 3 8 SWITCH MOUNTING BRACKET 4 9 ADAPTER i 4 10 WIRE HARNESS 1 11 CONSOLE i 5 12 SPEAKER GRILLE 2 13 COVER PLATE 1 14 COVER PLATE DECAL 1 I PARATION OF VEHICLE INTERIOR June 2 1999 INSTALLATION INSTRUCTION 4400304 Pr
4. ight If applicable align and fasten O E screws in O E clips in the roof of the vehicle Secure using 4 four 10 x1 2 screws item 1 pg 2 See Fig 5 8 Inset rear mounting bracket item 7 pg 2 with bent edges upward between headliner and sheet metal roof Slide bracket rearward until tabs engage rear O E brace Make sure that bracket engages securely Align slots in bracket with the center line scribed in the roof Secure brackets together using 3 three 10 x1 2 screws item 1 pg 2 See Figure 5 FIGURE 5 9 Install jumper wire harness item 10 pg 2 to O E HARNESS extend the O E M audio control harness 1f equipped See Figure 6 FIGURE 6 Il PREPARATION OF CONSOLE FOR INSTALLATION IF VEHICLE IS NOT EQUIPPED WITH FACTORY REAR A C AND REAR AUDIO CONTROLS PROCEED TO STEP 13 10 Carefully remove cover from respective switch location on console item 11 pg 2 if applicable See Fig 7 11 Using a razor knife trim away tab FIGURE 7 12 Install A C switch on driver s side opening and audio controls on passenger s side opening Note Make sure switches and controls are installed in the proper direction Remove backing from tape on switch mounting brackets item 8 pg 2 and install 1 one bracket on top and 1 one on bottom of each switch Press firmly on brackets to secure to switch and inside of console FIGURE 8 IF SPEAKER UPGRADE KIT WAS PURCHASED INSTALL PER INSTRUCTIONS PROVIDE
5. inted in the US A 2 IF VEHICLE IS NOT EQUIPPED WITH FACTORY REAR A C AND REAR AUDIO CONTROLS PROCEED TO STEP 4 1 Carefully remove the O E M console mounted to inner roof of vehicle by pulling downward on sides to release clips See Figure 1 2 Lower console and disconnect wiring at 3 three locations Remove and f t EKontrols from console and lay them in a safe place Discard console See Fig 2 FIGURE 2 3 Remove and retain 2 two O E M screws which secure plastic panel Slide panel rearward until front edge of panel can be lowered through headliner Slide forward and discard panel See Figure 3 4 Using a razor knife Caety trim headliner as shown Make sure the 27 cut is centered left to right in vehicle Caution Before cutting headliner material check for wiring or other componentry above headliner Cut only where indicated DO NOT OVERCUT HEADLINER See Figure 4 5 Remove and retain O E dome light Caution Headliner material is brittle Use care when removing dome light Access dome light clip through opening previously cut in headliner 6 Scribe a center line on the sheet metal roof of vehicle FIGURE 4 7 Remove and retain 2 two screws which secure front mounting bracket item 6 pg 2 to console item 11 pg 2 Install front mounting bracket over O E brace align slot with center line scribe and front edge of the O E brace Make sure that the bracket is centered left to r
6. t all wiring to components 16 Position console against headliner Loosely install using 2 two 6 32 x 3 4 screws item3 pg 2 through the smaller holes in bracket on console into threaded clips on front mounting bracket See fig 11 17 Using a scribe or similar tool align holes in speaker area with slots in mounting bracket Loosely secure sides of console using 2 two 8 x 3 4 screws item 2 pg 2 See figure 11 Make sure console alignment is straight then tighten all screws 18 Release video screen from locked position Lower video screen to viewing position for access to tae iat Wo riian P FIGURE 11 2 24 25 26 2i mounting location in top of video system housing 19 Raise video system into approximate position and connect all wiring to components Connect wiring and f So FIGURE 12 cabling to video system per instructions included with video system Check function of all components and lights See operating instructions for video system operations check For further assistance refer to the video system manual for the technical support phone number listed for your area Insert video system into opening in console Note Make sure wires do not get pinched o system and console 22 Align holes in housing with clips in mounting bracket Secure using 4 four 6 32x 3 4 screws item 3 pg 2 and 4 four 6 washers item 4 pg 2 See Figure 12 Caution Do not
Download Pdf Manuals
Related Search