AudioSource Amp Seven T User's Manual
Contents
1. Mi AudioSource Owner s Manual Amp Seven T Stereo Power Amplifier with Internal Bridging Ai etre We hope that you will enjoy your AudioSource Amp Seven T Please take a few moments to read this manual and be sure to retain this document for future reference Note If any part of this product is damaged or missing do not contact your AudioSource dealer Please call us directly at 800 435 7115 Using the Controls Front Panel Power This front panel button will manually switch the Amp Seven T on or off A multicolored LED indicates its power status To use the Auto On feature leave this front panel switch in the on position Speaker Selector The Amp Seven T has two pairs of speaker outputs Press button A to activate the A outputs Press button B to activate the B outputs Both A and B outputs may be used simultaneously provided the combined impedance does not fall below 2 ohms Before pressing either of the speaker selector buttons be sure that the level controls are set at the minimum position Input Level Controls These knobs adjust the incoming signal level and thereby act as volume controls We recommend that you set these at CAUTION MAROF ELETO GOW DO NOT OFEN SA Fh QUE O OHOO ELEOTRIOE NE RRO WUVRE min 288 orl Number hadh Tuvan midpoint and use your signal source receiver CD player preamplifier etc to adjust the volume CAUTION SA FUE CE OHO ELEOTRIOWE NE REOR wiwi 222. cts have fallen or liquid has been spilled into the appli ance c The appliance has been exposed to rain d The appli ance does not appear to operate normally or exhibits a marked change in performance or e The appliance has been dropped or the enclosure damaged Servicing The user should not attempt to service the appliance beyond that described in the operating instructions All other servicing should be referred to qualified service personnel Product Servicing In the event that your Amp Seven T fails to operated properly please contact the dealer where you purchased the unit Or you may contact AudioSource directly for further assistance Enjoy your new purchase This manual provides detailed diagrams and instructions for setting up your equipment Our commitment to your satisfaction doesn t end there We also offer friendly toll free assistance 1 800 HELP 115 Amp Seven T Specifications Amplifier Power Output 200 watts per channel 500 watts monobridged Total Harmonic Distortion Intermodulation Distortion Frequency Response Signal to Noise Ratio Input Sensitivity 0 cece eee 0 8 V Line Input Impedance 30K Q Line Design and specifications are subject to change without notice Mi AudioSource 9300 NorthDecatur Portland OR 97203 Tel 503 286 9300 Fax 503 978 3302 audiosource Phoenixgold com www audiosource net Headroom Functions Mono Bridging Rear Panel Auto Manual Power Switch Rear Pan
3. el Line RCA In Outputs Speaker A Left Right Speaker B Left Right Line Out Thru RCA Dimensions 16 1 2 W x 4 H x 13 1 4 D Weight 2000 AudioSource Inc
4. nnect to other amplifier or component inputs including when daisy chaining components These Stereo Setup In this configuration the bridging switch is off for stereo operation Connect the line out jacks from a stereo signal source to the line in jacks of your Amp Seven T Next connect your speak ers to the terminals marked Speaker A observing proper polarity red for and black for Connect a second pair of speakers to the terminals marked Speaker B Select between the A and or B speakers using the front panel speaker selector buttons Mono Setup inet In this configuration the bridging Ci a Armen switch is on Connect the line out from a signal source to the right line in of vn DDO your Amp Seven T Connect your mono T aeaaeae eee speaker to the terminals of your Amp Seven T following the example in the diagram opposite Use the right level A control on the front panel to adjust the volume Orri Nutone Maden Tuja Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Warning To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture Caution To reduce the risk of electric shock do not remove cover or back no user serviceable parts inside Refer servicing to qualified service personnel Caution To prevent electric shock match wide blade of pl
5. tion openings or placed in a built in situation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Sources The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance Grounding or Polarization Precautions should be taken so that the grounding or polariza tion means of an appliance is not defeated Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed on or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The appliance should be cleaned only as recommended by the manufacturer Power Lines An outdoor antenna should be located away from power lines Non Use Periods The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings Damage Requiring Service The appliance should be serviced by qualified service personnel when a The power supply cord or the plug has been damaged b Obje
6. ug to wide slot fully insert Attention Pour eviter les chocs electriques introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu au fond The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Read Instructions All the safety and operating instructions should be read before the appliance is operated Retain Instructions The safety and operating instructions should be adhered to Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Water and Moisture The appliance should not be used near water For example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool etc Ventilation The appliance should be situated so that its location or position does not interfere with its proper ventilation For example the appliance should not be situated on a bed sofa rug or similar surface that may block the ventila
7. waa ath CE ponet EVENE com e fs orl Number ban d In Tuvan Using the Controls Back Panel Manual Auto Power Switch Rear Panel In the Auto mode the Amp Seven T will turn on automatically when an input signal is sensed In the absence of an input signal the Amp Seven T will shut down automatically In the Auto mode the front panel power switch should always remain in the on posi tion In the Manual mode use the front panel power switch to activate the Amp Seven T Hooking up the Wires Audio signals travel out of one component and into another so all of your connections should go from out to in Line In If you are connecting a preamp or other signal source to the Amp Seven T connect the this signal source s line out jacks to the Amp Seven T s line in jacks Bridging Switch In addition to providing 200 watts RMS per channel in the stereo mode your Amp Seven T can be used as a high power 500 watt RMS mono amplifier Simply toggle the bridging switch from the stereo position to the mono position For mono applications use only the right channel input Similarly use only the right channel input level control Be sure to observe the correct speaker connections for bridged applications Because of the Amp Seven T s high power output in the mono mode we recommend initially setting the right level control at minimum and then adjusting the volume to the desired level Line Out Thru The line in thru jacks are used to co
Download Pdf Manuals
Related Search