Audiolab 8200A User's Manual
Contents
1. Any unauthorised repair or modification will void this warranty If any part is no longer available it will replaced with a fundional replacement part Any parts that are replaced will become the property of Audiolab Any repair or replacement under this warranty will not extend the poriod of warranty This warranty is valid only inthe country of purchase applies only to the first purchaser and is not transferable The following are not covered e Products on which the serial number hes bean removed altered or otherwise made illegibla e Normal wear and toar and cosmeticdamaga e Transportation or installation of the product e Acddental damage faults caused by commerdal use ads of God incorrect installation connedion or packaging misuse negled or careless operation or handling af the product which is not in accordance with Audiolab s usar instructions e Equipment thot hes baen operated in conjunction with unsuitable inappropriate cr faulty apparatus e Rapoirs or alterations carried out by parties other than 2 Introduction MODE RECORD INPUT SELECTOR SELECTOR Unpacking Unpack the produd fully The carton should contain e TheAudiolab 8200A integrored amplifier amp nelECpawercord suitable for your area e QnsRamote Handset with two AA botterles e Thisinstrudionmanudl If any item is missing or damaged report this to your dealer as soon as possible Retain the packing for future safe transport of your a2. TUNER AUX VIDEO IN TAPE 1 IN TAPE 2 IN The six inputs may be used for connecting any line level source VIDEO OUT TAPE 1 OUT TAPE 2 OUT Three sets of record outputs for connection of up to three stereo audio recorders e g tape recorder CD recorder audio recording input of DVD MP3 etc PRE AMP OUT 1 amp 2 Low impedance 100 ohm pre amplifier outputs for driving external power amplifiers sub woofers or signal processors Long cables may be used if required Pre amp outputs are switched off when integrated mode is selected or whenever amplifier is muted POWER AMP IN For driving the power amplifier input directly from an external source Only operates when pre power AV mode is selected LOUDSPEAKER TERMINALS Two sets of loudspeaker output terminals connected in parallel GROUND 7 Use only if phono pre amplifier and turntable are used and both are Class II double insulated no earth connection In this case the ground terminal can be connected to the metalwork of these units to eliminate residual hum The ground terminal must not be used as a safety earth If in doubt consult your dealer 4 Operation OUTPUT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Ce N21090 W b na N y Y N f b Ba Y x N P N y N E 4 zm e i be w l bb lt a LAG ALAD INAT AUDIOLAB HUNTINGDON UNITED KINGDOM PE29 6XU ATTENTION N Name NTEGRATED MOD
3. obvious cause before replacing the fuse with one of the correct rating and type The fuse values are 220 230V UK Korea etc T2 5AL 20mm Slow Blow 100 120V USA Japan etc T4 0AL 20mm SlowBlow Fuse Carrier The fuse is located in a slide in carrier which also contains a spare fuse The fuse carrier can only be pulled out after the IEC power cord is unplugged When the carrier is opened the first fuse to be seen is the spare fuse Remove and safely dispose of the fuse with the blown IEC Mains Connedor link before replacing it Class construction double insulated This product must not be connected to earth Power Cord An AC power cord is normally supplied with a mains plug suitable for your area If you have any doubts consult your dealer about obtaining a suitable power cord Important notice to UK users The appliance cord is terminated with a UK approved mains plug fitted with a 5A fuse If the fuse needs to be replaced an ASTA or BS approved BS1362 fuse rated at 5A must be used If you need to change the mains plug remove the fuse and dispose of this plug safely immediately after cutting it from the cord Connecting a Mains Plug The wires in the mains lead are coloured in accordance with the code Blue NEUTRAL Brown LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug proceed as follows The BLUE wire must be connected to the terminal marked w
4. other warranties whatsoever both express and implied including but not limited to the warranty of merchantability and fitness for a practical purposa This warranty provides benefits that are additional to and do not affect your statutory rights as a consumer Some countries and US states do not allow the exdusion or limitation of incidental or consaquantial damages or implied warranties so the axdusions in the paragraph above may not apply to you This warranty gives you spedfic legal rights and you may have other statutory rights which vary from state to state or country to country How to claim To obtain warranty service contac the Audiolab authorised dealer from which you purchased this produd Do not despatch goods without the prior agreement of tha dealer Audiolab or their authorised distributors If asked to return products for inspedion and or repair pack carefully preferably In the original cartons or packaging affording an equal degree of protedion and return prepaid If unsuitable packaging is used Audiolab may make a charge for the supply of new packaging Insurance is recommended as goods are returned at owner s risk Audiolab or their authorised distributors cannot be held liable for loss or damage intransit Packing insurance and freight on the return joumey will be paid by Audiolab or their authorised agents or distributor if corredive work proves to be necessary MUTE LED REMOTE RED Muts Dn CONTROLSENS
5. AUDIOLAB HUNTINGDON AA NAVE INTEGRATED voz i sz00n S No E CUCIOIC Lg S 2 DT IN o UNITED KINGDOM PE29 6XU DO pT FN ein AAW ALIDIO LAR LA K RIGHT 220 230V 50Hz 500W CH di b FUSE T4 0AL 250V CAUTION d Qj Audiola We f a AUDIOLAB HUNTINGDON o UNITED KINGDOM PE29 6XU RISQUES EAS OUVRIR DUE R WWW AUDIOLAB CO UK EI mm OUTPUT 220 230V 50Hz 440W NAME STEREO MODEL 8200P S No ie XE de eGooo999 QO999 446 opa 090000 ges GEI 990 Q990 9099900 OOO INPUT AUDIOLAB HUNTINGDON audiolab e A m CAUTION ATTENTION S EH audiolab o an WWW AUDIOLAB CO UK ay a BDA SBD w TRIGGER TRIGGER une NA une WF Switching On Make sure all the connections to and from the amp are secure and correct Make sure the operating mode is correctly set Plug the power cord into the wall socket and the amplifier Switch on at the mains and then switch on the 8200A The power indicator lights The unit is operational The amplifier may be operated via the front panel or the remote handset Gs NOTE Selecting MUTE from the front panel will disable the mute function on the UTPUTS IN
6. EL 8200A S No WWW AUDIOLAB CO UK RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR LEFT l HOLDER INPUT V LOUDSPEAKER TERMINALS V AMPLIFIER AMPLIFIER GA INPUT OUTPUTS TAPE2 TAPE 1 DVDEIC Standard Loudspeaker Connection Connecting Loudspeakers Switch power off when connecting loudspeakers Sa OUTPUT p tes Use good quality low resistance loudspeaker cable Connect the Positive RED terminal of the 68 amplifier to the Positive RED terminal of the 4 loudspeaker Connect the Negative BLACK ee terminals similarly When connecting loudspeakers tighten the Operating Modes Although the 8200A is an integrated amplifier it can function as a separate pre amplifier and power amplifier This allows the unit to be used in a variety of stereo and multichannel modes NOTE When switching modes the making and breaking of connections may momentarily operate the muting function on the 8200A Integrated Mode The pre amplifier section is internally connected to the power amplifier Pre amp outputs are not operational External subwoofers processors or amplifiers will not receive any signal Pre Power Mode The pre amplifier section is internally connected to the power amplifier The pre amplifier outputs are operational A powered subwoofer can be connected to the pre amplifier outputs A second power amplifier can be connected for bi amplifying as shown in the diagram An additional po
7. OR RED Power On VOLUME VOLUME HEADPHONE CONTROL SOCKET Remote Handset Buttons shown in white control the 8200A Buttons shown in grey operate Audiolab CD players and have no affacton the 02004 As the handset uses RC5 coding it will operate many other players Check with your dealer Mute Toggles mute On off Does not function if the MODE switch on the front panal is set to muta Input Press to select listening source Tha INPUT salador onthe front panel turns oo as Ji 2099 0906 OO OO a Salad muta to turn off pre amplifier outputs loudspeakers or headphones See sedion 4 for further details Headphons Socket Sockat for connection of headphones Unplug headphones when not in usa Conneding headphones mutes the loudspaakers and disconneds the pre amplifier outputs and power amplifier inputs If you wish to record the record input must be seleded manually Follow the polarity indications in the battery compartment Always replace batteries in pairs Use new batteries of the same type and rating ideally from the same manufacturer Controls And Functions Power Switch When power is switched on the 8200A is muted for 8 seconds 0 iDi Volume 3 Press vor 4 to raiseor lower the volume The VOLUME control on the front panel turns 3 Input amp Output Connections 220 230V 50Hz 440W FUSE T2 5AL 250V e eo FUSE MAINS RIGHT Signal Connections CD
8. PUT handset To restore normal operation select an operating mode A V PROCESSOR 290090 OOO Z sno aI cudiolab e A s
9. as been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Warning To reduce the risk of fire or electrical shock do not expose this product to rain or moisture The product must not be exposed to dripping and splashing and no object filled with liquids such as a vase of flowers should be placed on the product No naked flame sources such as candles should he placed on the product Caution Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate this device This equipment has been tested and found to comply with the limits for a Class B digitial device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by tuning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orientate or re locate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult
10. d do not hesitate to contact your dealer While cleaning is in progress the AC power cord must be unplugged from the AC power supply socket Any grease or dirt on the equipment may be removed with a soft lint free cloth slightly moistened with a mild solution of warm water and detergent or washing up liquid Do not use any other solutions or solvents Retain original packaging fortransporting equipment Il you have any queries regarding the use of Audiolab equipment consult your dealer Service Addresses UK IAG Servica Contra Unit 4 St Margaret s Way Stukeley Meadows Ind Estate Huntingdon Cambs PE29 GEB England Tel 44 0 1480 452561 Fax 44 0 1480 13403 Audiolab limited warranty Audiolab Lid warrants this produd subject to the terms and conditions below to be free from defects in materials and workmanship During tha warranty period Audiclab will repair or replace at Audiolab s option this product or any defective part in this product if it is found to be detective due to faulty materials workmanship or fundion The warranty period may vary from couniry to country Terms and conditions The warranty starts on the date of purchase or the date of delivery if this is later You must provide proof of purchase delivery batore work can be carried out Without this proof any work carried out will be chargeable to you All work will be carried out by Audiolab or its authorised agents or distributors
11. e it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product Headphone Output Output impedance 330 Q Suitable for headphones 8 2 2 kQ impedance Record Output VIDEO OUT TAPE 1 OUT TAPE 2 OUT Output impedance 1 kQ Gain from input to record output dB x1 Muting Muting controlled manually or automatically Accessories Supplied AC Power Cord Instruction Manual B200RC Remote Control with 2 x AA batteries Operating Temperature Range 10 35 C Power Requirements Depending on Region 50 60Hz 100 V 110 120 V and 220 230 V models available Maximum Power Consumption 440 V Dimensions WXHXD 445x74x335 mm including feet terminals and controls 445x 64 x302 mm excluding feet terminals and controls Weight Net 7 4 kg Shipping 8 8 kg Audiolab reserves the right to alter design and specification without notice Specification may vary for different countries Audiolab is a member of the International Audio Group repe was purchased They can take this product for environmental safe recycling IAG A LAB Mains supply and safety Mains Supply The mains operating voltage of all Audiolab units is shown on the rear panel If this does not match the voltage in your area consult your dealer The mains supply fuse is located on the rear panel of the unit If it has broken check for any
12. e product Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wider blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Use only attachments accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid h
13. ejlejlegh ue EM ha ato aereo 1 olpne mMMM o nu TU Z9OLLEV O8VLO Xxed OOZZVvv OSVLO IBL 1X9 6Z3d uopBunund Yed ssauisng euruJ3 qunog uBieJa os asnoH OVI qejoipny RECORD VOLUME GD L E pre mute integrated pre power pre power AV S200A OUTPUT TAPE 2 TAPE 1 VDEO CD 220 230V 50Hz 440W HS C AVS AVS HAXN VR AK N FUSE T2 5AL 250V imu Gr ean imu den mw Gens imu den Ex ba bad ba Q n21090 a D Be di N S WX Gef NEY Sey NEY NES IAG A LAB RIR AUDIOLAB HUNTINGDON CAUTION ATTENTION d RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE NAME INTEGRATED MODEL 8200A S No EE e U ICH e CH alle UNITED KINCDOM PEZ ai DO NOT OPEN NE PAS OUV WWW AUDIOLAB CO UK o2 00A User Instructions audiolab CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER REMOVEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ADVERTISSEMENT RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit Read these instructions Keep these instructions In the event that you pass the product to a third party this instruction manual should be provided along with th
14. ith the letter N or coloured BLUE or BLACK The BROWN wire must be connected to the terminal marked with the letter L or coloured Neutral BROWN or RED Power Amplifier Protection Circuits Short Circuit Protection If the output terminals are connected together or there is a short caused by a faulty speaker or connecting lead the amplifier will mute and un mute until the fault condition is removed DC Offset Protection If there is an internal or external fault which may cause DC voltage to be presented to the loudspeaker the amplifier will mute and stay muted until the fault is removed Thermal Protection If the amplifier is driven excessively for long periods or the output devices are pushed beyond their safe operating area the amplifier will switch off and then switch back on again when it has cooled down In all cases ifthe amplifier does not respond to remedial action consult your dealer Service and Warranty Servicing Servicing of Audiolab produds should only be carried out by authorised service agents If service is required the equipment should be returned securely packaged preferably using original packaging to your dealer In the UK equipment may be returned to the LAG Service Centra Always telephone before returning any equipment A nore should be enclosed giving your name address telephone number and a bristdescription of the reason for retum If you require Service outside the Warranty perio
15. mplifier If you dispose of tha packing do so with regard to any recycling regulations in your area Inserting Batteries in the Handset The battery compartmentis on the rear ofthe handset Unwrap the batteries open the compartment cover and Insert the batteries MODE SWITCH Always switch the power off before changing connedions Input Selector Turn to seled the listening source The 8200A mutes briefly when a new input is selected Volume Control Adjusts playing volume Always turn the volume up gradually Record Selactor Turn to seled source to record to Tape 1 Tape 2 or Video The connedians can also be used to connect to any recorder with analogue inputs such as a CD DAT recorder etc Record selactor and input selector operate independently It is possible to record from any source whilst listening to another Mode Switch Sala integrated whan using 8200 as an integrated amplifier Audiolab or its authorisad agents or distributors e Produdsnot purchased from an Audiolab authorised dealer e Produdsthat were not new at the time of original purchase e Produdssold csis osseen or with all faults Repairs or replacements cs provided under this warranty are tha exclusive remedy of the consumer Audiolab shall not be liable for any inddental or consequential damages for breach of any express or implied warranty in this product Except to tho extent prohibited by low this warranty Is exdusive and in lau of all
16. the dealer or an experienced radio TV technician for help Important Note The batteries supplied with this unit should be treated with care and not punctured or damaged Used batteries should be disposed of in full conformity with recycling regulations in your area NEVER dispose of batteries in a fire or in the general rubbish 6 Specifications Rated Output Power 60 W 18 dBW per channel into rated load impedance 8 Ohms with both channels driven Inputs CD TUNER AUX VIDEO TAPE 1 TAPE 2 125mV 20k 2 IHF POWER AMP 782 mV 47 KQ Gain PRE AMP 9dB 1 kHz POWER AMP 29 0 dB 1 kHz Signal To Noise Ratio CD TUNER AUX VIDEO TAPE 1 TAPE2 Better than 80dB IHF rel 0 5 V pre amp output POWER AMP better than 80dB IHF rel 0 dBW Frequency Response CD TUNER AUX VIDEO TAPE 1 TAPE 2 and POWER AMP 20 Hz 20 kHz 0 5 dB 1 Hz 65 kHz 3dB Total Harmonic Distortion amp Noise Less than 0 07 9o Channel Balance Within 1 dB Channel Separation Better than 60 dB 1 kHz any input Crosstalk Better than 80 dB 1 kHz Polarity phase Non inverting for all inputs and outputs Pre amp Output PRE OUT 1 and PRE OUT 2 Output Impedance 100 Q Maximum Output gt 7 3 V RMS Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health trom uncontrolled waste disposal recycl
17. wer amplifier can also be connected to drive a second pair of speakers in a remote location Pre Mode All signals to and from the power amplifier of the 8200A are disconnected In this mode the 8200A functions as a stand alone pre amplifier The pre amplifier section of the 8200A can be connected to a stereo power amplifier or to two monobloc amplifiers Pre Power AV The pre amplifier and power amplifier sections operate independently This mode can be used to connect a multichannel AV processor The processor should be connected via any spare tape output or as an alternative one of the pre amp outputs weisen AN terminals securely by hand Make there are no loose strands of wire which could You can connect a speaker switching box or headphone adaptor to the unused set of speaker terminals cause shorts Bi Wired Loudspeaker Connection eng SES ables Loudspeaker bi wiring offers improved sound quality because high and low frequency signals are carried individually to the loudspeaker drive units 20mm RED BLACK OUTPUT Connecting Cables PRE POWER MODE POWER AMP IN PRE AMP OUT 1 amp 2 INTERNAL LINK LOUDSPEAKERS RS ACTIVE tne ACTIVE integrated ACTIVE OPERATIONAL pre power ACTIVE OPERATIONAL pre power AV ACTIVE ACTIVE OPERATIONAL RIGHT OUTPUT LEFT s 220 230V 50Hz 440W pm FUSE T2 5AL 250V e eif G e e E ege 699999 ege GTO GOOOOO 990 2 di b
Download Pdf Manuals
Related Search