Attwood 4131 User's Manual
Contents
1. Aft Deck Shower and Deck Washdown systems 4131 4133 and 4132 Installation Instructions Attwood marine hardware navigational lighting bilge pumps and other marine accessories are specified more than any other brand by America s best known boat manufacturers as original equipment Look to Attwood for quality replacement parts and marine accessories SAVE THESE INSTRUCTIONS Form Number 69337 Rev B 03 10 FEATURES The Attwood Aft Deck Shower system 4131 4133 is designed for use on pleasure boats to rinse off swimmers and pets and to spray away salt and sand The shower systems hot and cold faucets blend water for ideal temperature It can also be used for cold water only The Deck Washdown System 4132 was designed with a high pressure sprayer for use on sport fishing boats to wash down the rear decks The sprayer has a valve to regulate or shut off the water Both systems feature a high styled hinged cover to store and protect the sprayhead and controls They are both made of high impact engineering grade polycarbonate plastic REQUIRED FOR INSTALLATION e Cordless drill 1 8 3mm and 1 2 13mm drill bits e Six 8 x 3 4 stainless steel countersunk or panhead screws Determine which screw type by matching feature on housing Fiqure 1 e Keyhole or sabre saw e Screwdriver e Channel lock pliers or wrench set e Teflon tape optional e Brass or plastic standard 1 2 pipe end cap optional Figure 1 Counte2. ll four corners of the template Cut an 8 1 2 x 4 opening 2 Remove cover and sprayhead Place box in opening and mark all screw hole locations Remove box and drill pilot holes 3 Attach hose to pump outlet Wrap hose connections with teflon tape or use pipe joint compound to prevent leaks 4 Thread end of hose through hole in end of box and attach to end of sprayhead 5 Connect wiring of switch to pump using insulated crimp on connectors Fuse according to pump manufacturers specifications Run system to test all connections for leaks 6 Place box in cutout opening Check to be sure that the hose is free to be pulled out and pushed back into place Attach box using all six screws CAUTION Do not overtighten screws CARE AND MAINTENANCE Be sure to drain all water lines and fittings whenever system may be subjected to temperatures below freezing gt 41 4 s A ee ips Drill Bit TEMPLATE 8 1 2 aa 1 4 Radius y This product carries the standard Attwood one year limited warranty See product catalog for details 2003 Attwood Corporation 1016 N Monroe Street Lowell MI 49331 0260 www attwoodmarine com
3. r Sunk A WARNING Always remove the boat from the water before using 120V AC power tools LOCATION Select a location that will allow the cover to swing freely and allow room for hose storage and plumbing Panhead AFT DECK SHOWER 4131 4133 INSTALLATION 1 Using the template on the reverse side of these instructions drill a 1 2 hole at all four corners of the template Cut an 8 1 2 x 4 opening 2 Remove cover and sprayhead Place box in opening and mark all screw hole locations Remove box and drill pilot holes 3 Attach water lines to appropriate hot cold controls Wrap hose connections with teflon tape or use pipe joint compound to prevent leaks Note If only cold water connection is made it is important that the remaining hot water connection be sealed by installing a standard 1 2 pipe end cap to prevent accidental water discharge inside the boat 4 Attach spray hose to center threaded fitting between hot and cold connections 5 Place enclosed hot and cold labels on appropriate knobs 6 Thread end of hose through hole in end of box and attach to end of sprayhead 7 Test all connections for leaks 8 Place box in cutout opening Check to be sure that the hose is free to be pulled out and pushed back into place Attach box using all six screws CAUTION Do not overtighten screws DECK WASHDOWN 4132 INSTALLATION 1 Using the template on the reverse side of these instructions drill a 1 2 hole at a
Download Pdf Manuals
Related Search