Atdec TH-3060-UFH User's Manual
Contents
1. TH 3060 UFH Installation Instructions 6telehook Flat screen wall mount Full Motion height adjustable Component Checklist Display Hardware Bag 5S yee Display Mounting panner oe Coach Screw x4 Ss SerRwe Bag 0 E 6mm 4mm M8 x 16mm x4 Nylon Anchor x4 Allen key M8 x 25mm x4 TS M Nyloc Nut x4 12mm Washer x4 M x 16mm x4 M6 x 6mm screw x4 KG 20mm Washer x4 M6 x 25mm x4 Tools required Philips head screwdriver 5mm 0 2 drill bit 10mm 0 39 masonary drill bit Mount f cap x2 Wall plate cover x2 y Display Bracket x2 Power drill IMPORTANT INFORMATION IMPORTANT Install Telehook Flatscreen wall mount as per Installation Instructions This product supports a minimum load of 5kg 111lbs and a maximum load of 25kg 55lbs This product supports VESA mounting hole configurations from 200mm x 200mm to 400mm x 400mm The Manufacturer accepts no responsibility for incorrect installation Step 1 Check Components Check you have received all parts against the Component Checklist and Hardware Step 2 Mounting Location This product has a feature where the arm will automatically lock in position when pushed up against the wall to the left If this feature is to be used allow clearance to the left when deciding the mounting location Wall Tocked position D Clearance i To unlock pull the chord down whi2. ep 8 Attach Mounting Rails To Display pm The Mounting rails support VESA hole configurations from 200mm x 200mm to 400mm x 400mm Only insert the M x 6mm screws in the mounting rail attached to the top of the display Tighten fully then undo one half turn ia oe Display mounting screw Mounting rail Step 9 Attach Display to Display Mount A Prior to attaching your Display check which of the three pairs of keyhole mounting positions on the Display Mount to use that will also allow access to the lower mounting slots eee in the top mounting B bracket into your chosen pair of keyhole mounting positions on the display mount keyholes SS of screws Step 10 Display Height Adjustment A The Arm may need to be adjusted to suit the weight of the display If the Display drops down the spring tension will need to be increased If the Display rises the spring tension will need to be decreased v Step 11 Tilt Adjustment DANAN 5 _ Uh loosen the nuts on both sides of the tilt mount Turn left nut Anti clockwise S Turn right nut Clockwise desired viewing angle v Installation complete e Aag Adjust the Display to the C Attach M x 6mm screws to the lower mounting rail to 4 secure the display Z More tension for heavier displays B To adju
3. lst ree movement moving the arm away from the wall Step 3 Install Arm to the wall Masonary Wall Timber Stud wall Drilled hole p Drilled hole Wall J a oY eJl TG Aa F fe f ie S Nylon Anchor W CA i ae Se ee Using a 10mm 0 39 masonary drill bit Drill four holes Using a 5mm 0 2 drill bit Drill three holes 60mm 2 4 60mm 2 4 deep deep f Secure the mounting plate to the wall using the Coach Secure the mounting plate to the wall using the Coach Screws supplied NOTE Use a stud finder to accurately locate the centre of the stud Ensure that all screws fix securely into stud Screws and Nylon Anchors supplied Step 4 Attach Wall Plate Covers Step 5 Attach Display Mount to Arm lt a A N N i ao a LAN Y al ATA Vo g vI De LEO g i lt lt KL g L a q a an a a i Washer al a a Mount lt M6 Nyloc Nut tighten firmly Step 6 Horizontal Rotation Adjustment Step 7 Attach Screw Covers 5 B This will a p allow 10 r Horizontal Ys g rotation Aoa AN g adjustment KEN g g J A From the tightened position undo each nut a quarter of a turn two times ED e J Sue E g n lt lt lt J Va l Note The nuts can be re tightened to gt j d secure the display in position or left to allow g IKA HA IU future changes a b St
4. st the tension use the supplied 6mm Allen Key less tension for lighter displays SSS U Tighten nuts to secure position Wall Turn left nut Clockwise C Bi LI Turn right nut Anti clockwise a ON atdec No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd Due to the continuing product development the manufacturer reserves the right to alter specifications without notice Published 07 09 12
Download Pdf Manuals
Related Search