Atdec TH3070CTW User's Manual
Contents
1. IMPORTANT This Addendum MUST be used Installation Addendum with the Installation Instructions supplied with Telehook Ceiling T E E E Hi O O IKC Tilt TH 3070 CTW TH 3070 CTW Back to Back Conversion Kit Component Checklist z WARNING Bits Box pay E Failure to follow these installation 5 b Y o instructions and those in the TH 3070 CTW R DD i D k JID ol may result in personal injury and or damage M8 xl mm M xl mm M5 xl mm to Audio Visual quipment M8 x 55mm M x 12mm Mounting Mounting Mounting Screw Grub Screw x3 screws x6 Screws x6 Screws x6 me jy Product check list k DD Us S O Wall Mount Wall Mount W mm Allen Key 5mm Allen Key 3mm Allen Key M4 xl mm Bracket Left Bracket Right 1 x TH 3070 CTW separate product Mounting gm Screws x6 a M8 x45mm W P Wall Mount 1 x Back to Back conversion kit J Washer x6 Locking Screws x2 Horizontal Bar Slider x2 Collar Front Check Component Checklist and Product Checklist Ensure you have received all components in both Component Checklist and Product Checklist Refer to the Telehook TH 3070 CTW Installation Instructions 1 Follow steps A B C on the Telehook TH 3070 CTW Installation Instructions 2 Follow step D on Telehook TH 3070 CTW Installation Instructions and repeat for 2nd display 3 Follow steps E F and repeat for 2nd display bracket Once complete continue step C below Attaching the2. Mount to the Ceiling Hanger haa Swivel Insert Collar Front M8 x 30mm Screws 1 Attach the three Swivel Inserts to the hanger 2 Attach the two front collars to the Hanger Pole so that they sit on at the height that has been chosen to mount the the swivel inserts as shown above Tighten the M8 x 30mm screws so display that the collars are secure on the hanger however do not over tighten Mounting the Display a Note The brackets should rest on the horizontal bar with the slider between the bracket M8 Small Washer Note This operation will require two persons 1 Lift one of the displays with brackets attached and hook the brackets over the sliders Hold the display firmly insert the two M8 x 45mm screws and tighten firmly using the Hex Tool 2 Repeat for 2nd Display Adjusting the viewing position of your display 1 Tilt Adjust 5 to 25 Tilt 5 to 25 Tilt one of the display brackets and adjust 1 Loosen both M8x45mm screws on the tilt angle of the display to the required position Tighten the two lock ing screws with Hex Tool provided 2 Repeat for 2nd Display WARNING Do not attempt to adjust tilt angle without firstly loosening locking screws Doing so may damage the product 2 Pan Adjust Horizontal Bar 1 Adjust grub screw 1 until the display sits level Once the display is level tighten grub s
3. crew 2 until it firmly tightens onto the 1 To adjust the pan position of the display loosen all four horizontal bar Tighten grub screw 3 until it M8 x 30mm screws with the 6mm Allen Key then rotate the Hanger firmly tightens onto the horizontal bar and Pole Collar to the desired position Once in position tighten all four prevents it from moving M8 x 30mm screws as tight as possible to lock the display in position 2 Repeat for 2nd Display Bracket F Refer to the Telehook TH 3070 CTW Installation Instructions Follow steps K and L in the Telehook TH 3070 CTW Installation Instructions to attach adhesive vinyl and apply additional security if required a atdec TFT Manufacturers are constantly releasing new monitor models Atdec does not accept responsibility if the mounting hole pattern does not comply with the international VESA standards Due to continuing product development the manufacturer reserves the right to alter specitications without notice Published 12 12 08
Download Pdf Manuals
Related Search