ATD Tools Clock ATD-701 User's Manual
Contents
1. ATD 701 Non contact Infrared Thermometer Instruction manual Compact rugged and easy to use Just aim and push the button read target surface temperatures in less than a second Safely measure surface temperatures of hot hazardous or hard to reach objects without contact gt Reflected energy ransmiited energy j ae 1 Emitted energy e Lt 7 1 eee Lh AN Object AA N WU i 1h 1 i Infrared thermometer measures the surface temperature of an object The unit s optics sense emitted reflected and transmitted energy which is collect and focused onto a detector The unit s electronics transmitted energy which is display on the unit For increased ease and accuracy the laser pointer makes aiming even more precise Infrared thermometer should be protected from the following EMF electro magnetic fields from arc welders induction heaters Thermal shock cause by large or abrupt ambient temperature changes allow 1 hour for unit to stabilize before use Do not leave the unit on or near objects of high temperature Do not point laser at eye or indirectly off reflective surfaces When take measurement point thermometer toward the object to be measured and hold the red trigger The object under test should be larger than the spot size calculated by the field of view diagram 2 Distance amp spot size As the distance from the object increase the spot size of measuring area b2. california to cause cancer bi defects or other reproductive harm Always wear appropriate safety equipment and clothing whe product Study understand and follow all instru provided with this product
3. ecomes larger D S 10 1 mma SOmme TOOmme q jji 10mm TI an ae S 3 Field of view Make sure the target is larger than the unit s spot size The smaller the target the closer measuring distance When accuracy is critical make sure the target is at least twice as large as the spot size 4 Emissivity Most organic materials and painted or oxidized surfaces have an emissivity of 0 95 Inaccurate readings will result from measuring shiny or polished metal surfaces To compensate cover the surface to be measured with masking tape or flat black paint Measure the tape or painted surface when the tape or painted reach the same temperature as the material underneath Trigger h i al Battery door finger indents Figure 2 7 Figure 1 F 1 Press battery door clip install battery correctly Pull the trigger LCD display reading amp battery icon Release the trigger and the reading will hold for 7 seconds LCD display Laser pointer turn on prompt Alarm of high temperature prompt Alarm of Low temperature prompt Data Hold Measure result Emissivity Temperature unit C Temperature unit F rgomimogdw D gt Figure 3 M 2 Locating a hot spot aim the thermometer outside the area of interest then scan across with up and down motions until you locate the hot spot please turn on the laser to for accurate measuring Figure 4 Figure 5 3 Diagram descrip
4. tion 1 Trigger Press for turn on and then display test result and hold data 7 seconds automatically HOLD after unclamping switch Turn off automatically after 10 seconds without operate 2 Laser pointer button press it for turn on laser pointer press again for turn off 3 Back light Up button In Alarm temperature and setting emissivity mode for adjust value up In other mode for turn on back light When product working press it for turn on back light press again for turn off 4 MODE button Press MODE button for cycle options MAX AVG MIN HAL LAL mode A MAX Measure maximum data current B MIN Measure minimum data current C AVG Calculate the average of all measure data D HAL Alarm of high temperature Option HAL mode press UP or DN button for set alarm temperature When LCD display H means measure result exceeded the alarm temperature E LAL Alarm of low temperature Option HAL mode press UP or DN button for set alarm temperature When LCD display L means measure result under the alarm temperature 5 T DN button In Alarm temperature and setting emissivity mode for adjust value down When turn on product and press direct for C select 6 SET button Press for setting emissivity And press UP or DN for adjust from 0 1 1 0 Press SET button again for exit setting mode 7 LCD display 8 Battery door When replace ba
5. ttery please using the finger indents to pull open the battery door Maintenance 1 Lens cleaning Blow off lose particles using clean compressed air Gently brush remaining debris away with a moist cotton cloth 2 Case cleaning Clean the case with a damp sponge cloth and mild soap 3 Please take out the battery when not using for a long time Note 1 Donot use solvent to clean lens 2 Donot submerge the unit in water pecitications range S 3 Cor 3 of rdg 30 C to 0 C 22 to 32 Accuracy 2 Cor 2 of rdg 0 C to 100 C 32 to 212 F 3 Cor 3 of rdg 2100 C 212 F 1 of reading or 1 C 0 1 1 0 adjustable 10 95 RH non condensing epeaine 0 C to 60 C 32 to 140 F temperature 20 60 C 4 140 F without battery Note Display AL means ambient temp lower than 0 Display AH means ambient temp higher than 60 C Display above code in normal ambient temp probable means this meter was broken Attached list Applicable Emissivity for Different Material For reference only Material Emissivity Material Emissivity _ Bast ozo fol f 0o Brick 090 Paper 095 Concrete 095 San o9 Dirt Snow Ce E E e __ 98 Twoo ooa WARNING Always wear ANSI approved safety goggles when using this product Normal use of this product is likely to expose the user to dust and or microscopic particles containing chemica known to the state of
Download Pdf Manuals
Related Search